Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Development of a process for the production and purification of alpha- and beta-galactooligosaccharides from Bifobacterium bifidum NCIMB 41171

Synthesis of prebiotic alpha- and beta-galactooligosaccharides (GOS) using the whole cells of Bifidobacterium bifidum NCIMB 41171 was investigated. Determination of alpha- and beta-galactosidase activities showed them to be at 3 and 205 g(-1) of freeze dried biomass, respectively, and they increased to 5 and 344 U g(-1), respectively, when cells were treated with toluene. Starting with 450-500 mg mL(-1) lactose, maximum GOS concentrations were observed at 80-85% lactose conversions and the mixtures contained oligosaccharides (with a degree of polymerisation >= 3) at 77-109 mg mL(-1) and trans-galactosylated disaccharides between 85-115 mg mL(-1). The GOS yield values varied between 36% and 43%. An alpha-linked disaccharide was detected and its presence was confirmed by gas chromatography mass spectroscopy. Cells were re-used up to 8 times without changes in reaction times or the substrate conversions to GOS. Oligosaccharide synthesis was not inhibited by the presence of glucose or galactose. The mixtures were successfully purified from glucose (92% of glucose removed) by fermentation with Saccharomyces cerevisiae with no losses in the oligosaccharide content and only a small decrease on the galactose. (c) 2006 Elsevier Ltd. All rights reserved.

Development of a process model for the automatic miniload warehouse expansion

This paper provides an insight to the development of a process model for the essential expansion of the automatic miniload warehouse. The model is based on the literature research and covers four phases of a warehouse expansion: the preparatory phase, the current state analysis, the design phase and the decision making phase. In addition to the literature research, the presented model is based on a reliable data set and can be applicable with a reasonable effort to ensure the informed decision on the warehouse layout. The model is addressed to users who are usually employees of logistics department, and is oriented on the improvement of the daily business organization combined with the warehouse expansion planning.

Development of a process for producing an ashless, low-sulfur fuel from coal.

Prepared for the Office of Coal Research, Dept. of the Interior...by the Pittsburg & Midway Coal Mining Co., Kansas City, Mo.

Reliability modelling and verification of manufacturing processes based on process knowledge management

Reliability modelling and verification is indispensable in modern manufacturing, especially for product development risk reduction. Based on the discussion of the deficiencies of traditional reliability modelling methods for process reliability, a novel modelling method is presented herein that draws upon a knowledge network of process scenarios based on the analytic network process (ANP). An integration framework of manufacturing process reliability and product quality is presented together with a product development and reliability verification process. According to the roles of key characteristics (KCs) in manufacturing processes, KCs are organised into four clusters, that is, product KCs, material KCs, operation KCs and equipment KCs, which represent the process knowledge network of manufacturing processes. A mathematical model and algorithm is developed for calculating the reliability requirements of KCs with respect to different manufacturing process scenarios. A case study on valve-sleeve component manufacturing is provided as an application example of the new reliability modelling and verification procedure. This methodology is applied in the valve-sleeve component manufacturing processes to manage and deploy production resources.

A configuration framework of manufacturing strategy paradigm in state owned enterprises within China's petrochemical industry:building context-embedded configurations for the paradigm of strategic manufacturing management from exploratory case studies

The role of the production system as a key determinant of competitive performance of business operations- has long been the subject of industrial organization research, even predating the .explicit conceptua1isation of manufacturing, strategy in the literature. Particular emergent production issues such as the globalisation of production, global supply chain management, management of integrated manufacturing and a growing e~busjness environment are expected to critically influence the overall competitive performance and therefore the strategic success of the organization. More than ever, there is a critical need to configure and improve production system and operations competence in a strategic way so as to contribute to the long-term competitiveness of the organization. In order to operate competitively and profitably, manufacturing companies, no matter how well managed, all need a long-term 'strategic direction' for the development of operations competence in order to consistently produce more market value with less cost towards a leadership position. As to the long-term competitiveness, it is more important to establish a dynamic 'strategic perspective' for continuous operational improvements in pursuit of this direction, as well as ongoing reviews of the direction in relation to the overall operating context. However, it also clear that the 'existing paradigm of manufacturing strategy development' is incapable of adequately responding to the increasing complexities and variations of contemporary business operations. This has been factually reflected as many manufacturing companies are finding that methodologies advocated in the existing paradigm for developing manufacturing strategy have very limited scale and scope for contextual contingency in empirical application. More importantly, there has also emerged a deficiency in the multidimensional and integrative profile from a theoretical perspective when operationalising the underlying concept of strategic manufacturing management established in the literature. The point of departure for this study was a recognition of such contextual and unitary limitations in the existing paradigm of manufacturing strategy development when applied to contemporary industrial organizations in general, and Chinese State Owned Enterprises (SOEs) in particular. As China gradually becomes integrated into the world economy, the relevance of Western management theory and its paradigm becomes a practical matter as much as a theoretical issue. Since China markedly differs from Western countries in terms of culture, society, and political and economic systems, it presents promising grounds to test and refine existing management theories and paradigms with greater contextual contingency and wider theoretical perspective. Under China's ongoing programmes of SOE reform, there has been an increased recognition that strategy development is the very essence of the management task for managers of manufacturing companies in the same way as it is for their counterparts in Western economies. However, the Western paradigm often displays a rather naive and unitary perspective of the nature of strategic management decision-making, one which largely overlooks context-embedded factors and social/political influences on the development of manufacturing strategy. This thesis studies the successful experiences of developing manufacturing strategy from five high-performing large-scale SOEs within China’s petrochemical industry. China’s petrochemical industry constitutes a basic heavy industrial sector, which has always been a strategic focus for reform and development by the Chinese government. Using a confirmation approach, the study has focused on exploring and conceptualising the empirical paradigm of manufacturing strategy development practiced by management. That is examining the ‘empirical specifics’ and surfacing the ‘managerial perceptions’ of content configuration, context of consideration, and process organization for developing a manufacturing strategy during the practice. The research investigation adopts a qualitative exploratory case study methodology with a semi-structural front-end research design. Data collection follows a longitudinal and multiple-case design and triangulates case evidence from sources including qualitative interviews, direct observation, and a search of documentations and archival records. Data analysis follows an investigative progression from a within-case preliminary interpretation of facts to a cross-case search for patterns through theoretical comparison and analytical generalization. The underlying conceptions in both the literature of manufacturing strategy and related studies in business strategy were used to develop theoretical framework and analytical templates applied during data collection and analysis. The thesis makes both empirical and theoretical contributions to our understanding of 'contemporary management paradigm of manufacturing strategy development'. First, it provides a valuable contextual contingency of the 'subject' using the business setting of China's SOEs in petrochemical industry. This has been unpacked into empirical configurations developed for its context of consideration, its content and process respectively. Of special note, a lean paradigm of business operations and production management discovered at case companies has significant implications as an emerging alternative for high-volume capital intensive state manufacturing in China. Second, it provides a multidimensional and integrative theoretical profile of the 'subject' based upon managerial perspectives conceptualised at case companies when operationalising manufacturing strategy. This has been unpacked into conceptual frameworks developed for its context of consideration, its content constructs, and its process patterns respectively. Notably, a synergies perspective towards the operating context, competitive priorities and competence development of business operations and production management has significant implications for implementing a lean manufacturing paradigm. As a whole, in so doing, the thesis established a theoretical platform for future refinement and development of context-specific methodologies for developing manufacturing strategy.

Blockade of T-cell costimulation prevents development of experimental chronic renal allograft rejection.

Blocking CD28-B7 T-cell costimulation by systemic administration of CTLA4Ig, a fusion protein which binds B7 molecules on the surface of antigen-presenting cells, prevents rejection and induces tolerance in experimental acute allograft rejection models. We tested the effect of CTLA4Ig therapy on the process of chronic renal allograft rejection using an established experimental transplantation model. F344 kidneys were transplanted orthotopically into bilaterally nephrectomized LEW recipients. Control animals received low dose cyclosporine for 10 days posttransplantation. Administration of a single injection of CTLA4Ig on day 2 posttransplant alone or in addition to the low dose cyclosporine protocol resulted in improvement of long-term graft survival as compared with controls. More importantly, control recipients which received cyclosporine only developed progressive proteinuria by 8-12 weeks, and morphological evidence of chronic rejection by 16-24 weeks, including widespread transplant arteriosclerosis and focal and segmental glomerulosclerosis, while animals treated with CTLA4Ig alone or in addition to cyclosporine did not. Competitive reverse transcriptase-PCR and immunohistological analysis of allografts at 8, 16, and 24 weeks showed attenuation of lymphocyte and macrophage infiltration and activation in the CTLA4Ig-treated animals, as compared with cyclosporine-alone treated controls. These data confirm that early blockade of the CD28-B7 T-cell costimulatory pathway prevents later development and evolution of chronic renal allograft rejection. Our results indicate that T-cell recognition of alloantigen is a central event in initiating the process of chronic rejection, and that strategies targeted at blocking T-cell costimulation may prove to be a valuable clinical approach to preventing development of the process.

Koordinaattimittauksen kehittäminen metsäkonetuotannossa

Tämän diplomityön tarkoituksena oli koordinaattimittauksen kehittäminen ja systematisointi metsäkoneen valmistuksessa. Työssä tutkittiin kannettavalla nivelvarsimittalaitteella tehtävää koordinaattimittausta tehtaan omille tuotteille, valmistuksen apuvälineille ja toimittajilta tuleville osille. Tavoitteena oli mittaustoiminnan kokonaisvaltainen kehittäminen ja vastauksia haettiin seuraaviin tutkimuskysymyksiin: Mitä kohteita tulee mitata? Missä tuotantovaiheessa mittausta tarvitaan? Kuinka mittaustuloksia tulee käsitellä ja hyödyntää? Kuinka paljon mittaustoiminta vaatii resursseja ja kuinka hyvin käytössä oleva koordinaattimittauslaite soveltuu yrityksen tuotantoon? Lisäksi pohdittiin koordinaattimittauksen merkitystä yritykselle ja etsittiin kehityskohteita mittaustoiminnasta? Tutkimusaineistona käytettiin vuosien 2007 – 2008 aikana saatuja koordinaattimittauskokemuksia ja mittaustuloksia. Lisäksi tutkittiin yrityksen sisäisiä poikkeamaraportteja ja tutustuttiin koordinaattimittauslaitteen ja mittausohjelman toimintaan sekä yrityksen tuotantoon. Tutkimuksessa tultiin siihen tulokseen, että koordinaattimittauksen ensisijainen tavoite tulee olla valmistusprosessin kehittäminen ja mittauslaitetta tulee käyttää tehokkaasti hyväksi uusien tuotteiden valmistuksen alkuvaiheessa.

Tuotantoprosessin kehittäminen LEAN -periaatteita hyödyntäen

Tutkimuksen tarkoituksena oli löytää keinoja kehittää kansainvälisen komponenttitoimittajan tilaus-toimitusprosessia ja parantaa sitä Lean –filosofiaan pohjautuvien menetelmien avulla. Työn teoreettisessa osuudessa tarkasteltiin toimittajayhteistyön muotoja ja kilpailukykyyn vaikuttavia tekijöitä kansainvälisessä ympäristössä Toisena tarkastelun kohteena oli Lean –filosofiaan pohjautuvat, tuotantoprosessille soveltuvat kehittämismenetelmät. Empiirinen osuus keskittyi tilaustoimitusprosessiin tutkimusyrityksessä. Tutkimuksessa selvisi, että resurssien ja osaamisen merkitys tuotannon laadussa ja kehittämisessä on merkittävä. Lisäksi monipuolinen osaaminen tuo joustavuutta toimitusketjuun ja parantaa sisäistä asiakkuus –ajattelua. Tilaustoimitusketjun tehokkuutta voidaan parantaa hyödyntäen tapaukselle parhaiten soveltuvia Lean –menetelmiä ja kehittämällä toimittajayhteistyötä.

Development of new rapid prototyping process

Purpose - The purpose of this paper is to identify the key elements of a new rapid prototyping process, which involves layer-by-layer deposition of liquid-state material and at the same time using an ultraviolet line source to cure the deposited material. This paper reports studies about the behaviour of filaments, deposition accuracy, filaments interaction and functional feasibility of system. Additionally, the author describes the process which has been proposed, the equipment that has been used for these studies and the material which was developed in this application. Design/methodology/approach - The research has been separated into three study areas in accordance with their goals. In the first, both the behaviour of filament and deposition accuracy was studied. The design of the experiment is described with focus on four response factors (bead width, filament quality, deposition accuracy and deposition continuity) along with function of three control factors (deposition height, deposition velocity and extrusion velocity). The author also studied the interaction between filaments as a function of bead centre distance. In addition, two test samples were prepared to serve as a proof of the methodology and to verify the functional feasibility of the process which has been studied. Findings - The results show that the proposed process is functionally feasible, and that it is possible to identify the main effects of control factors over response factors. That analysis is used to predict the condition of process as a function of the parameters which control the process. Also identified were distances of centre beads which result in a specific behaviour. The types of interaction between filaments were analysed and sorted into: union, separation and indeterminate. At the end, the functional feasibility of process was proved whereby two test parts could be built. Originality/value - This paper proposes a new rapid prototyping process and also presents test studies related to this proposition. The author has focused on the filament behaviour, deposition accuracy, interaction between filaments and studied the functional feasibility of process to provide new information about this process, which at the same time is useful to the development of other rapid prototyping processes.

Development of a platform for lean manufacturing simulation games

More than ever, the economic globalization is creating the need to increase business competitiveness. Lean manufacturing is a management philosophy oriented to the elimination of activities that do not create any type of value and are thus considered a waste. One of the main differences from other management philosophies is the shop-floor focus and the operators' involvement. Therefore, the training of all organization levels is crucial for the success of lean manufacturing. Universities should also participate actively in this process by developing students' lean management skills and promoting a better and faster integration of students into their future organizations. This paper proposes a single realistic manufacturing platform, involving production and assembly operations, to learn by playing many of the lean tools such as VSM, 5S, SMED, poke-yoke, line balance, TPM, Mizusumashi, plant layout, and JIT/kanban. This simulation game was built in tight cooperation with experienced lean companies under the international program “Lean Learning Academy,”http://www.leanlearningacademy.eu/ and its main aim is to make bachelor and master courses in applied sciences more attractive by integrating classic lectures with a simulated production environment that could result in more motivated students and higher study yields. The simulation game results show that our approach is efficient in providing a realistic platform for the effective learning of lean principles, tools, and mindset, which can be easily included in course classes of less than two hours.

Development of procedures for the design, optimization and manufacturing of customized orthopaedic and trauma implants: Geometrical/anatomical modelling from 3D medical imaging

Tese de Doutoramento (Programa Doutoral em Engenharia Biomédica)

Development of a retrospective job exposure matrix for PCB-exposed workers in capacitor manufacturing

Objectives: Polychlorinated biphenyls (PCBs) are considered probable human carcinogens by the International Agency for Research on Cancer and one congener, PCB126, has been rated as a known human carcinogen. A period-specific job exposure matrix (JEM) was developed for former PCB-exposed capacitor manufacturing workers (n=12,605) (1938-1977). Methods: A detailed exposure assessment for this plant was based on a number of exposure determinants (proximity, degree of contact with PCBs, temperature, ventilation, process control, job mobility). The intensity and frequency of PCB exposures by job for both inhalation and dermal exposures, and additional chemical exposures were reviewed. The JEM was developed in nine steps: (1) all unique jobs (n=1,684) were assessed using (2) defined PCB exposure determinants; (3) the exposure determinants were used to develop exposure profiles; (4) similar exposure profiles were combined into categories having similar PCB exposures; (5) qualitative intensity (high-medium-low-baseline) and frequency (continuous-intermittent) ratings were developed, and (6) used to qualitatively rate inhalation and dermal exposure separately for each category; (7) quantitative intensity ratings based on available air concentrations were developed for inhalation and dermal exposures based on equal importance of both routes of exposure; (8) adjustments were made for overall exposure, and (9) for each category the product of intensity and frequency was calculated, and exposure in the earlier era was weighted. Results: A period-specific JEM modified for two eras of stable PCB exposure conditions. Conclusions: These exposure estimates, derived from a systematic and rigorous use of the exposure determinant data, lead to cumulative PCB exposure-response relationships in the epidemiological cancer mortality and incidence studies of this cohort. [Authors]

Development of Special Pumps Repair Process

Tässä diplomityössä käsitellään erikoispumppujen korjausprosessia teollisuuspumppujen korjauksiin erikoistuneessa konepajassa. Työn pääasiallinen tarkoitus on tuotantoprosessin kehittäminen ja tuotantovaiheiden esitteleminen. Tavoitteen taustalla on pyrkimys entisestään parantaa palvelukykyä ja asiakastyytyväisyyttä.Kolme eri keinoa päätavoitteen saavuttamiseksi ovat tuotannon suunnittelun ja ohjauksen kehittäminen, työssä käsiteltyjen pumpputyyppien korjausprosessien läpäisyaikojen lyhentäminen sekä korjausvaiheiden määrittely ja esittely vaihe vaiheelta. Työssä käsiteltyjä erikoispumpputyyppejä ovat imupumput, monijaksopumput sekä pysty/potkuripumput.Tuotannonsuunnittelun ja -ohjauksen kehittämiseksi sekä läpäisyaikojen lyhentämiseksi työssä etsittiin vaihtoehtoisia toimintatapoja. Kolmas tavoite, eli korjausvaiheiden määrittely, toteutettiin esittelemällä korjausprosessin vaiheet käsitellyillä pumpputyypeillä.Tuloksena saatiin keinoja tuotannon suunnittelun ja hallinnan kehittämiseksi. Useimmat keinot koskevat toimintatapojen selkiyttämistä. Myös keinoja läpäisyaikojen lyhentämiseksi löydettiin. Tietyllä imupumpputyypillä ja -koolla läpäisyajan lyheneminen oli 25 % ja osalla monijaksopumpuista jopa 75 %. Tulokset saavutetaan varastoimalla tiettyjä komponentteja, joilla on pitkä valmistus- tai korjausaika. Pysty/potkuripumppujen korjauksen läpäisyaikaa ei saatu lyhennettyä työn rajausten puitteissa Näiden tulosten lisäksi korjausprosessin toimintatavat määriteltiin.

Characterization Of Process Efficiency Improvement In Laser Additive Manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, has gained a lot of interest in past recent years within various industries, such as medical and aerospace industries. LAM enables fabrication of complex 3D geometries by melting metal powder layer by layer with laser beam. Research in laser additive manufacturing has been focused in development of new materials and new applications in past 10 years. Since this technology is on cutting edge, efficiency of manufacturing process is in center role of research of this industry. Aim of this thesis is to characterize methods for process efficiency improvements in laser additive manufacturing. The aim is also to clarify the effect of process parameters to the stability of the process and in microstructure of manufactured pieces. Experimental tests of this thesis were made with various process parameters and their effect on build pieces has been studied, when additive manufacturing was performed with a modified research machine representing EOSINT M-series and with EOS EOSINT M280. Material used was stainless steel 17-4 PH. Also, some of the methods for process efficiency improvements were tested. Literature review of this thesis presents basics of laser additive manufacturing, methods for improve the process efficiency and laser beam – material- interaction. It was observed that there are only few public studies about process efficiency of laser additive manufacturing of stainless steel. According to literature, it is possible to improve process efficiency with higher power lasers and thicker layer thicknesses. The process efficiency improvement is possible if the effect of process parameter changes in manufactured pieces is known. According to experiments carried out in this thesis, it was concluded that process parameters have major role in single track formation in laser additive manufacturing. Rough estimation equations were created to describe the effect of input parameters to output parameters. The experimental results showed that the WDA (width-depth-area of cross-sections of single track) is correlating exponentially with energy density input. The energy density input is combination of the input parameters of laser power, laser beam spot diameter and scan speed. The use of skin-core technique enables improvement of process efficiency as the core of the part is manufactured with higher laser power and thicker layer thickness and the skin with lower laser power and thinner layer thickness in order to maintain high resolution. In this technique the interface between skin and core must have overlapping in order to achieve full dense parts. It was also noticed in this thesis that keyhole can be formed in LAM process. It was noticed that the threshold intensity value of 106 W/cm2 was exceeded during the tests. This means that in these tests the keyhole formation was possible.