Development of a simple UV-spectrophotometric method for the determination of lansoprazole and study of its degradation profile

A UV-spectrophotometric method is described for the determination of lansoprazole (LAN). The method is based on the measurement of the absorbance of LAN solution in acetonitrile at 281 nm. The system obeyed Beer's law over the concentration range of 1.25-25.0 µg/mL. The degradation behavior of LAN was investigated under dry heat treatment, UV-degradation, acid hydrolysis, alkali hydrolysis and oxidation; and found to degrade extensively under acid hydrolysis, alkali hydrolysis and oxidation. The method was applied to the determination of LAN in capsule and the results were statistically compared with those of the reference method by applying Student's t-test and F-test.

Degradation of all-inkjet-printed organic thin-film transistors with TIPS-pentacene under processes applied in textile manufacturing

Printed electronics represent an alternative solution for the manufacturing of low-temperature and large area flexible electronics. The use of inkjet printing is showing major advantages when compared to other established printing technologies such as, gravure, screen or offset printing, allowing the reduction of manufacturing costs due to its efficient material usage and the direct-writing approach without requirement of any masks. However, several technological restrictions for printed electronics can hinder its application potential, e.g. the device stability under atmospheric or even more stringent conditions. Here, we study the influence of specific mechanical, chemical, and temperature treatments usually appearing in manufacturing processes for textiles on the electrical performance of all-inkjet-printed organic thin-film transistors (OTFTs). Therefore, OTFTs where manufactured with silver electrodes, a UV curable dielectric, and 6,13-bis(triisopropylsilylethynyl) pentance (TIPS-pentacene) as the active semiconductor layer. All the layers were deposited using inkjet printing. After electrical characterization of the printed OTFTs, a simple encapsulation method was applied followed by the degradation study allowing a comparison of the electrical performance of treated and not treated OTFTs. Industrial calendering, dyeing, washing and stentering were selected as typical textile processes and treatment methods for the printed OTFTs. It is shown that the all-inkjet-printed OTFTs fabricated in this work are functional after their submission to the textiles processes but with degradation in the electrical performance, exhibiting higher degradation in the OTFTs with shorter channel lengths (L=10 μm).

The identification, distribution and persistence of oxamyl and its degradation products in planted corn seed, seedling root and soil from oxamyl-treated corn seeds

A simple method was developed for treating corn seeds with oxamyl. It involved soaking the seeds to ensure oxamyl uptake, centrifugation to draw off excess solution, and drying under a stream of air to prevent the formation of fungus. The seeds were found to have an even distribution of oxamyl. Seeds remained fungus-free even 12 months after treatment. The highest nonphytotoxic treatment level was obtained by using a 4.00 mg/mL oxamyl solution. Extraction methods for the determination of oxamyl (methyl-N'N'-dimethyl-N-[(methylcarbamoyl)oxy]-l-thiooxamimidate), its oxime (methyl-N',N'-dimethyl-N-hydroxy-1-thiooxamimidate), and DMCF (N,N-dimethyl-1-cyanoformanade) in seed" root, and soil were developed. Seeds were processed by homogenizing, then shaking in methanol. Significantly more oxamyl was extracted from hydrated seeds as opposed to dry seeds. Soils were extracted by tumbling in methanol; recoveries range~ from 86 - 87% for oxamyl. Root was extracted to 93% efficiency for oxamyl by homogenizing the tissue in methanol. NucharAttaclay column cleanup afforded suitable extracts for analysis by RP-HPLC on a C18 column and UV detection at 254 nm. In the degradation study, oxamyl was found to dissipate from the seed down into the soil. It was also detected in the root. Oxime was detected in both the seed and soil, but not in the root. DMCF was detected in small amounts only in the seed.

Photo-assisted electrochemical degradation of the commercial herbicide atrazine

This paper presents a degradation study of the pesticide atrazine using photo-assisted electrochemical methods at a dimensionally stable anode (DSA (R)) of nominal composition Ti/Ru(0.3)Ti(0.7)O(2) in a prototype reactor. The effects of current density, electrolyte flow-rate, as well as the use of different atrazine concentrations are reported. The results indicate that the energy consumption is substantially reduced for the combined photochemical and electrochemical processes when compared to the isolated systems. It is observed that complete atrazine removal is achieved at low current densities when using the combined method, thus reducing the energy required to operate the electrochemical system. The results also include the investigation of the phytotoxicity of the treated solutions.

Stability study of darunavir ethanolate tablets applying a new stability-indicating HPLC method

Chemical and physical degradation of drugs may result in altered therapeutic efficacy and even toxic effects. Therefore, the aim of this work was to study the stability of darunavir and to develop and validate a liquid chromatography (LC) method to determine darunavir in raw material and tablets in the presence of degradation products. The novel method showed to be linear from 6.0 to 21.0 μg/mL, with high precision (CV < 2%) and accuracy (recuperation of 99.64%). It is simple and reliable, free of placebo interferences. The robustness of the method was evaluated by a factorial design using seven different parameters. Forced degradation study was done under alkaline, acidic, and oxidative stress at ambient temperature and by heating. The LC method was able to quantify and separate darunavir and its degradation products. Darunavir showed to be unstable under alkaline, acid, and oxidative conditions. The novelty of this study is understanding the factors that affect darunavir ethanolate stability in tablets, which is the first step to unravel the path to know the degradation products. The novel stability-indicating method can be used to monitor the drug and the main degradation products in low concentrations in which there is linearity.

Interaction between bradykinin potentiating nonapeptide (BPP9a) and beta-cyclodextrin: A structural and thermodynamic study

Herein, we demonstrate the physical and chemical characterizations of the supramolecular complex formed between beta-cyclodextrin (beta CD) and bradykinin potentiating nonapeptide (BPP9a), an endogenous toxin found in Bothrops jararaca. Circular dichroism results indicate a conformational change in the BPP9a secondary structure upon its complexation with beta CD. Nuclear magnetic resonance results, mainly from NOESY experiments, and theoretical calculations showed a favorable interaction between the tryptophan residue of BPP9a and the beta CD cavity. Thermodynamic inclusion parameters were investigated by isothermal titration calorimetry, demonstrating that beta CD/BPP9a complex formation is an exothermic process that results in a reduction in entropy. Additionally, in vitro degradation study of BPP9a against trypsin (37 degrees C, pH 7.2) showed higher stability of peptide in presence of beta CD. This beta CD/BPP9a complex, which presents new chemical properties arising from the peptide inclusion process, may be useful as an antihypertensive drug in oral pharmaceutical formulations. (C) 2011 Elsevier B.V. All rights reserved.

Estudo inicial da degradação in vivo de poli(L-co-D,L ácido lático), sintetizado em laboratório, aplicado como prótese tibial em coelhos

The copolymer poly (L-co-D,L lactic acid), PLDLA, has gained prominence in the field of temporary prostheses due to the fact that their time of degradation is quite compatible with the requirement in the case of osseous fracture. In this work the in vivo degradation of devices from copolymer, as a system of plates and screws, used in fixation of the tibia of rabbits was studied. The devices were implanted in 15 adult rabbits, albinos, New Zealand race, and they were used as control devices of alloys of titanium (Ti-6Al-4V/ V grade). The use of copolymers, synthesized in the laboratory, was tested in the repair of fracture in rabbits'tibias, being assessed in the following times: 2 weeks, 2 months and 3 months. Morphological analysis of tissue surrounding the plate and screw system, for 2 weeks of implantation, showed the presence of osteoblasts, indicating a pre bone formation. After 2 months there was new bone formation in the region in contact with the polymer. This bone growth occurred simultaneously with the process of PLDLA degradation, invading the region where there was polymer and after 3 months there was an intense degradation of the copolymer and hence greater tissue invasion compared to 2 months which characterized bone formation in a region where the polymer degraded. The in vivo degradation study of the devices for PLDLA by means of histological evaluations during the period of consolidation of the fracture showed the efficiency of plate and screw system, and it was possible to check formation of bone tissue at the implantation site, without the presence of inflammatory reaction

Estudo da degradação de membranas arquitetónicas

Dissertação de mestrado Internacional em Sustentabilidade do Ambiente Construído

Evaluation of Control Structures for Stabilizing Degrading Stream Channels in Western Iowa, Phases II and III, HR-208A, 1985

Since the turn of the century, tributaries to the Missouri River in western Iowa have entrenched their channels to as much as six times their original depth. This channel degradation is accompanied by widening as the channel side slopes become unstable and landslides occur. The deepening and widening of these streams have endangered about 25% of the highway bridges in 13 counties [Lohnes et al. 1980]. Grade stabilization structures have been recommended as the most effective remedial measure for stream degradation [Brice et al., 1978]. In western Iowa, within the last seven years, reinforced concrete grade stabilization structures have cost between $300,000 and $1,200,000. Recognizing that the high cost of these structures may be prohibitive in many situations, the Iowa Department of Transportation (Iowa DOT) sponsored a study at Iowa State University (ISU) to find low-cost alternative structures. This was Phase I of the stream degradation study. Analytical and laboratory work led to the conclusion that alternative construction materials such as gabions and soil-cement might result in more economical structures [Lohnes et al. 1980]. The ISU study also recommended that six experimental structures be built and their performance evaluated. Phase II involved the design of the demonstration structures, and Phase III included monitoring and evaluating their performance.

Avaliação da degradação do diclofenaco sódico utilizando H2O2/fenton em reator eletroquímico

This paper describes a degradation study of the anti-inflammatory sodium diclofenac in aqueous medium using an electro-chemical flow reactor with a gas diffusion electrode as cathode. Two degradation processes were compared: by H2O2 electro-generated and H2O2 electro-generated/Fe(II). Concentration of sodium diclofenac was determined during the experiments by HPLC. The changes in chemical oxigen demand (COD) were also evaluated. Under the specific reaction conditions, 350 mg L-1 of H2O2 was electro-generated and 99.2% of sodium diclofenac was degradated, with 27.4% COD reduction. At the same conditions, but using Fe(II), drug degradation was 99.4% and the COD reduction was 63.2%.

Degradação fotocatalítica de sulfametoxazol, trimetoprima e diclofenaco em solução aquosa

In this work the photocatalytic degradation of sulfametoxazole, trimethoprim and potassium diclofenac was evaluated by using TiO2 and ZnO photocatalysts. In optimized experimental conditions (pH 4, TiO2: 50 mg) the TiO2-photocatalysis allowed an almost total degradation of the studied drugs with mineralization of about 80% at reaction times of 120 min. Some mechanistic differences were observed between TiO2 and ZnO in the degradation study involving potassium diclofenac. At the first reaction times the use of ZnO leads to generation of transient species that strongly absorb in the UV spectral region, a fact not observed in studies involving TiO2.

Development and validation of a stability-indicating UPLC method for rosuvastatin and its related impurities in pharmaceutical dosage forms

The present work describes a novel stability-indicating reversed-phase ultra performance liquid chromatography method for the separation and quantification of rosuvastatin (RSV) and its related impurities in the pharmaceutical dosage forms under forced degradation conditions. An unknown degradation impurity detected in the acid degradation was identified by using quadrupole time-of-flight mass spectrometry. The chromatographic separation was carried out on C-18 column (100 x 2.1 mm, 1.7 μm) using isocratic elution with methanol and 0.1% trifluoroacetic acid (50:50). The total run time was 12 min within which RSV as well as all related impurities and degradation products were separated. The developed method was validated for RSV and related impurities in pharmaceutical dosage forms.

Biobased films prepared from NaOH/thiourea aqueous solution of chitosan and linter cellulose

In the present study, films based on linter cellulose and chitosan were prepared using an aqueous solution of sodium hydroxide (NaOH)/thiourea as the solvent system. The dissolution process of cellulose and chitosan in NaOH/thiourea aqueous solution was followed by the partial chain depolymerization of both biopolymers, which facilitates their solubilization. Biobased films with different chitosan/cellulose ratios were then elaborated by a casting method and subsequent solvent evaporation. They were characterized by X-ray analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), thermal analysis, and tests related to tensile strength and biodegradation properties. The SEM images of the biofilms with 50/50 and 60/40 ratio of chitosan/cellulose showed surfaces more wrinkled than the others. The AFM images indicated that higher the content of chitosan in the biobased composite film, higher is the average roughness value. It was inferred through thermal analysis that the thermal stability was affected by the presence of chitosan in the films; the initial temperature of decomposition was shifted to lower levels in the presence of chitosan. Results from the tests for tensile strength indicated that the blending of cellulose and chitosan improved the mechanical properties of the films and that an increase in chitosan content led to production of films with higher tensile strength and percentage of elongation. The degradation study in a simulated soil showed that the higher the crystallinity, the lower is the biodegradation rate.

Estudo da degradação de resinas compostas pela ação de bebidas alcoólicas: análise de fluorescência e rugosidade superficial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização físico-química e avaliação toxicológica preliminar do copolímero sulfato de condroitina-co-N-isopropilacrilamida para uso farmacêutico

A Indústria Farmacêutica utiliza polímeros em forma de nanopartículas em formulações de liberação controlada e vetorizada por possuírem baixo custo em relação a demais métodos de preparações de formas farmacêuticas, aparentemente não serem reconhecidos pelo sistema de defesa do organismo, proporcionar melhora da eficácia, diminuição da toxicidade e da dose de fármaco administrado. O sulfato de condroitina-co-Nisopropilacrilamida (SCM + NIPAAm) é um copolímero proposto para este fim, a partir da reação de um polímero sintético, o poli N-isopropilacrilamida (PNIPAAm), com características termossensíveis, com um natural, o Sulfato de Condroitina (SC), com características bioadesivas. Assim, a copolimerização pode ser capaz de somar estas propriedades e aperfeiçoar o seu uso como um veículo para liberação controlada. Este trabalho objetivou, portanto, realizar a caracterização fisico-quimica das partículas de sulfato de condroitina e Nisopropilacrilamida e do copolímero SCM+NIPAAm (2,5 % e 5%) e do SCM+PNIPAAm 2,5% e uma avaliação toxicológica parcial de um destes copolímeros que apresentar as melhores propriedades de um eficiente carreador de fármacos, selecionado a partir dos ensaios de caracterização físico-química. Para determinar a estrutura química dos sistemas particulados e analisar os seus componentes químicos, foi realizada a Espectroscopia de Ressonância Magnética Nuclear (RMN) e Espectroscopia do Infravermelho com Transformada de Fourrier (FTIR); Para analisar a morfologia das partículas, foi usado a Microscopia Eletrônica de Varredura (MEV); A Termogravimetria/ Termogravimetria Derivada e Análise Térmica Diferencial (TG/DTG) foi usada para avaliar o comportamento térmico dos sistemas particulados, bem como auxiliar na análise de Cinética de Degradação (CD, método de Flynn-Wall-Ozawa); Foi ainda realizado a técnica de degradação in vitro e a determinação carga superficial e tamanho de partículas (análise do Potencial Zeta, PZ). Para avaliar a toxicidade, foi realizado o bioensaio em microcrustáceo Artemia salina (24 e 48 h), viabilidade celular (citotoxicidade) em células PC-12 (método do MTT) e também a toxicidade aguda oral em camundongos. As análises de RMN, FTIR e MEV demonstraram semelhança quanto ao aspecto estrutural e morfológico entre os copolímeros estudados. As análises de TG demonstraram que o SCM+NIPAAm 5% apresentou maior estabilidade térmica em relação aos demais copolímeros avaliados, uma vez que sua decomposição polimérica ocorre em temperaturas superiores, em torno de 233ºC. O DTA demonstrou valores de temperaturas concordantes com os eventos térmicos de decomposição apresentados pelas curvas das análises TG. Sua estabilidade foi confirmada através da CD e estudo de degradação in vitro, apresentando, respectivamente, Ea > 100 kJ mol^-1 e perda de 48% da sua massa inicial após três meses. Além disso, SCM+NIPAAm 5% apresentou diâmetro de partícula inferior a 200 nm e índice de polidispersão de 0,35, além do PZ > -30mV, caracteristicas de um promissor candidato a carreador de fármacos. Em relação às avaliações toxicológicas, o SCM+NIPAAm 5% não apresentou toxicidade no bioensaio de A. salina (CL₅₀ > 1000) e no modelo celular avaliado, dentro das concentrações e circunstâncias de exposição estudadas. O SCM+NIPAAm 5%, na dose oral de 2000 mg/kg, não apresentou nenhum sinal evidente de toxicidade em camundongos, o que foi corroborado pela ausência de alterações anatomo-histopatológicas. A copolimerização do Sulfato de Condroitina e N-isopropilacrilamida na concentração estudada, dada suas características físico-químicas e toxicológicas preliminares, apresenta propriedades que contribuem para a proposta de um sistema que constitui uma nova forma de liberação controlada, especialmente de fármacos.