The influence of fatty acid methyl ester profiles on inter-cycle variability in a heavy duty compression ignition engine

With the advent of alternative fuels, such as biodiesels and related blends, it is important to develop an understanding of their effects on inter-cycle variability which, in turn, influences engine performance as well as its emission. Using four methanol trans-esterified biomass fuels of differing carbon chain length and degree of unsaturation, this paper provides insight into the effect that alternative fuels have on inter-cycle variability. The experiments were conducted with a heavy-duty Cummins, turbo-charged, common-rail compression ignition engine. Combustion performance is reported in terms of the following key in-cylinder parameters: indicated mean effective pressure (IMEP), net heat release rate (NHRR), standard deviation of variability (StDev), coefficient of variation (CoV), peak pressure, peak pressure timing and maximum rate of pressure rise. A link is also established between the cyclic variability and oxygen ratio, which is a good indicator of stoichiometry. The results show that the fatty acid structures did not have a significant effect on injection timing, injection duration, injection pressure, StDev of IMEP, or the timing of peak motoring and combustion pressures. However, a significant effect was noted on the premixed and diffusion combustion proportions, combustion peak pressure and maximum rate of pressure rise. Additionally, the boost pressure, IMEP and combustion peak pressure were found to be directly correlated to the oxygen ratio. The emission of particles positively correlates with oxygen content in the fuel as well as in the air-fuel mixture resulting in a higher total number of particles per unit of mass.

Autoxidation of conjugated linoleic acid methyl ester in the presence of α-tocopherol: the hydroperoxide pathway

The autoxidation of conjugated linoleic acid (CLA) is poorly understood in spite of increasing interest in the beneficial biological properties of CLA and growing consumption of CLA-rich foods. In this thesis, the autoxidation reactions of the two major CLA isomers, 9-cis,11-trans-octadecadienoic acid and 10-trans,12-cis-octadecadienoic acid, are investigated. The results contribute to an understanding of the early stages of the autoxidation of CLA methyl ester, and provide for the first time a means of producing and separating intact CLA methyl ester hydroperoxides as well as basic knowledge on lipid hydroperoxides and their hydroxy derivatives. Conjugated diene allylic monohydroperoxides were discovered as primary autoxidation products formed during autoxidation of CLA methyl esters in the presence and absence of α-tocopherol. This established that one of the autoxidation pathways of CLA methyl ester is the hydroperoxide pathway. Hydroperoxides were produced from the two major CLA methyl esters by taking advantage of the effect of α-tocopherol to promote hydroperoxide formation. The hydroperoxides were analysed and separated first as methyl hydroxyoctadecadienoates and then as intact hydroperoxides by HPLC. The isolated products were characterized by UV, GC-MS, and NMR techniques. In the presence of a high amount of α-tocopherol, the autoxidation of CLA methyl ester yields six kinetically-controlled conjugated diene monohydroperoxides and is diastereoselective in favour of one particular geometric isomer as a pair of enantiomers. The primary autoxidation products produced from the two major CLA isomers include new positional isomers of conjugated diene monohydroperoxides, the 8-, 10-, 12-, and 14-hydroperoxyoctadecadienoates. Furthermore, two of these new positional isomers have an unusual structure for a cis,trans lipid hydroperoxide where the allylic methine carbon is adjacent to the cis instead of the usual trans double bond. The 1H and 13C NMR spectra of nine isomeric methyl hydroxyoctadecadienoates and of ten isomeric methyl hydroperoxyoctadecadienoates including the unusual cis,trans hydroperoxides, i.e. Me 8-OOH-9c,11t and Me 14-OOH-10t,12c, were fully assigned with the aid of 2D NMR spectroscopy. The assigned NMR data enabled determination of the effects of the hydroxyl and hydroperoxyl groups on the carbon chemical shifts of CLA isomers, identification of diagnostic signals, and determination of chemical shift differences of the olefinic resonances that may help with the assignment of structure to as yet unknown lipid hydroperoxides either as hydroxy derivatives or as intact hydroperoxides. A mechanism for the hydroperoxide pathway of CLA autoxidation in the presence of a high amount of α-tocopherol was proposed based on the characterized primary products, their relative distribution, and theoretical calculations. This is an important step forward in CLA research, where exact mechanisms for the autoxidation of CLA have not been presented before. Knowledge of these hydroperoxide formation steps is of crucial importance for understanding the subsequent steps and the different pathways of the autoxidation of CLA. Moreover, a deeper understanding of the autoxidation mechanisms is required for ensuring the safety of CLA-rich foods. Knowledge of CLA oxidation and how it differs from the oxidation of nonconjugated polyunsaturated fatty acids may also be the key to understanding the biological mechanisms of CLA activity.

Structure of N-tert-butyloxycarbonyl-[alpha]-aminoisobutyryl-DL-pipecolyl-[alpha]-aminoisobutyric acid methyl ester

C20H35N3O6 (Boc-Aib-DL-Pip-Aib-OMe, Boc = tert-butyloxycarbonyl, Aib = alpha-aminoisobutyric acid, Pip = pipecolic acid, OMe = methoxy), M(r) = 413.5, monoclinic, P2(1)/c, a = 18.055 (3), b = 15.048 (3), c = 17.173 (3) angstrom, beta = 91.7 (1)-degrees, V = 4663.8 (9) angstrom3, Z = 8, D(m) = 1.16, D(x) = 1.178 Mg m-3, lambda(Mo Kalpha) = 0.71069 angstrom, mu = 0.081 mm-1, F(000) = 1792, T = 297 K. The final R value for 4925 [I greater-than-or-equal-to 3sigma(I)] reflections is 0.065 (wR = 0.067). The peptide backbone of the two independent molecules in the asymmetric unit is folded at the -Aib-Pip- sequence to form a type-I (I') beta-bend stabilized by a 1 <-- 4 intramolecular N-H...O=C hydrogen bond between the Aib(3) peptide N-H and Boc urethane C=O groups.

Congruence of fatty acid methyl ester profiles and morphological characters of arbuscular mycorrhizal fungi in Gigasporaceae.

Arbuscular mycorrhizal (AM) fungi (Order Glomales, Class Zygomycetes) are a diverse group of soil fungi that form mutualistic associations with the roots of most species of higher plants. Despite intensive study over the past 25 years, the phylogenetic relationships among AM fungi, and thus many details of evolution of the symbiosis, remain unclear. Cladistic analysis was performed on fatty acid methyl ester (FAME) profiles of 15 species in Gigaspora and Scutellospora (family Gigasporaceae) by using a restricted maximum likelihood approach of continuous character data. Results were compared to a parsimony analysis of spore morphological characters of the same species. Only one tree was generated from each character set. Morphological and developmental data suggest that species with the simplest spore types are ancestral whereas those with complicated inner wall structures are derived. Spores of those species having a complex wall structure pass through stages of development identical to the mature stages of simpler spores, suggesting a pattern of classical Haeckelian recapitulation in evolution of spore characters. Analysis of FAME profiles supported this hypothesis when Glomus leptotichum was used as the outgroup. However, when Glomus etunicatum was chosen as the outgroup, the polarity of the entire tree was reversed. Our results suggest that FAME profiles contain useful information and provide independent criteria for generating phylogenetic hypotheses in AM fungi. The maximum likelihood approach to analyzing FAME profiles also may prove useful for many other groups of organisms in which profiles are empirically shown to be stable and heritable.

Combustion analysis of microalgae methyl ester in a common rail direct injection diesel engine

In this study, the biodiesel properties and effects of blends of oil methyl ester petroleum diesel on a CI direct injection diesel engine is investigated. Blends were obtained from the marine dinoflagellate Crypthecodinium cohnii and waste cooking oil. The experiment was conducted using a four-cylinder, turbo-charged common rail direct injection diesel engine at four loads (25%, 50%, 75% and 100%). Three blends (10%, 20% and 50%) of microalgae oil methyl ester and a 20% blend of waste cooking oil methyl ester were compared to petroleum diesel. To establish suitability of the fuels for a CI engine, the effects of the three microalgae fuel blends at different engine loads were assessed by measuring engine performance, i.e. mean effective pressure (IMEP), brake mean effective pressure (BMEP), in cylinder pressure, maximum pressure rise rate, brake-specific fuel consumption (BSFC), brake thermal efficiency (BTE), heat release rate and gaseous emissions (NO, NOx,and unburned hydrocarbons (UHC)). Results were then compared to engine performance characteristics for operation with a 20% waste cooking oil/petroleum diesel blend and petroleum diesel. In addition, physical and chemical properties of the fuels were measured. Use of microalgae methyl ester reduced the instantaneous cylinder pressure and engine output torque, when compared to that of petroleum diesel, by a maximum of 4.5% at 50% blend at full throttle. The lower calorific value of the microalgae oil methyl ester blends increased the BSFC, which ultimately reduced the BTE by up to 4% at higher loads. Minor reductions of IMEP and BMEP were recorded for both the microalgae and the waste cooking oil methyl ester blends at low loads, with a maximum of 7% reduction at 75% load compared to petroleum diesel. Furthermore, compared to petroleum diesel, gaseous emissions of NO and NOx, increased for operations with biodiesel blends. At full load, NO and NOx emissions increased by 22% when 50% microalgae blends were used. Petroleum diesel and a 20% blend of waste cooking oil methyl ester had emissions of UHC that were similar, but those of microalgae oil methyl ester/petroleum diesel blends were reduced by at least 50% for all blends and engine conditions. The tested microalgae methyl esters contain some long-chain, polyunsaturated fatty acid methyl esters (FAMEs) (C22:5 and C22:6) not commonly found in terrestrial-crop-derived biodiesels yet all fuel properties were satisfied or were very close to the ASTM 6751-12 and EN14214 standards. Therefore, Crypthecodinium cohnii- derived microalgae biodiesel/petroleum blends of up to 50% are projected to meet all fuel property standards and, engine performance and emission results from this study clearly show its suitability for regular use in diesel engines.

Iridoid glucosides from Randia spinosa (Rubiaceae)

An iridoid glucoside: randinoside, along with five known iridoids: galioside, deacetylasperulosidic acid methyl ester, scandoside methyl ester, geniposide and gardenoside, were isolated from the stems of Randia spinosa. The structures were determined by spectroscopic analysis, including 2D NMR techniques. © 2003 Elsevier Science Ltd. All rights reserved.

A 1h And 13c Magnetic Resonance And Infrared Spectroscopic Study Of Coordinated 2-Aminocyclopentene-1-Dithiocarboxylic Acid And Its S-Methyl Ester

The ligating properties of 2-aminocyclopentene-1-dithiocarboxylic acid and its S-methyl esters were investigated. Complexes with Zn(II), Cd(II) and Hg(II) halides were synthesized and characterized by infrared and proton and carbon-13 NMR studies. The results are concordant with a bidentate coordination of the -CS2 group to the metal ions

In vitro phototoxicity of 5-aminolevulinic acid and its methyl ester and the influence of barrier properties on their release from a bioadhesive patch.

opical administration of excess exogenous 5-aminolevulinic acid (ALA) leads to selective accumulation of the potent photosensitiser protoporphyrin IX (PpIX) in neoplastic cells, which can then be destroyed by irradiation with visible light. Due to its hydrophilicity, ALA penetrates deep lesions, such as nodular basal cell carcinomas (BCCs) poorly. As a result, more lipophilic esters of ALA have been employed to improve tissue penetration. In this study, the in vitro release of ALA and M-ALA from proprietary creams and novel patch-based systems across normal stratum corneum and a model membrane designed to mimic the abnormal stratum corneum overlying neoplastic skin lesions were investigated. Receiver compartment drug concentrations were compared with the concentrations of each drug producing high levels of PpIX production and subsequent light-induced kill in a model neoplastic cell line (LOX). LOX cells were found to be quite resistant to ALA- and M-ALA-induced phototoxicity. However, drug concentrations achieved in receiver compartments were comparable to those required to induce high levels of cell death upon irradiation in cell lines reported in the literature. Patches released significantly less drug across normal stratum corneum and significantly more across the model membrane. This is of major significance since the selectivity of PDT for neoplastic lesions will be further enhanced by the delivery system. ALA/M-ALA will only be delivered in significant amounts to the abnormal tissue. PpIX will only then accumulate in the neoplastic cells and the normal surrounding tissue will be unharmed upon irradiation.

A Heat and Light Mediated Synthetic Sequence Serendipitous Synthesis of Methyl Ester of Tris-Norpterosin-E

Synthesis of methyl ester of 3-oxo-indan-5-acetic acid (3), an analogue of the natura1 product pterosin-E (4), starting from cyclopentadiene (1) and p-benzoquinone (2) using a sequence of six ground and excited state reactions, is described.

Synthesis and imidization of poly(amic methyl ester)s

The synthesis and characterization of a series of poly(amic methyl ester)s from five aromatic dianhydrides and a diamine, 4,4'-oxydianiline (ODA), are described. These poly(amic ester)s are obtained by the low-temperature polycondensation from dianhydrides derived diester-diacyl chlorides and ODA in DMAc solution with the inherent viscosities in the 0.5-0.9 dL/g range. These precursors are readily soluble in aprotic solvents. A detailed thermal study of the imidization process is presented, based on dynamic and isothermal TGA measurements, FTIR spectroscopy, and dynamic mechanical analysis. (C) 1997 John Wiley & Sons, Inc.

Electron impact and chemical ionization mass spectral analyses of methyl esters species of free mycolic acid fraction from Rhodococcus lentifragmentus

The free mycolic acid fraction from Rhodococcus lentifragmentus was derivatized to methyl esters and further fractionated into saturated (F-0), monounsaturated (F-1) and diunsaturated (F-2) species using argentation-TLC. Methyl esters fractions F-0, F-1 and F-2, accounting for approximately 7.4%, 53.1% and 39.5%, respectively, were analyzed by electron impact (EI) and chemical ionization (CI) mass spectrometries. According to EI-MS, peaks observed for M(+)-18, that were prominent compared to those representing M(+)-32 and M(+)-(18 + 32), indicated that the carbon chain size ranged from C-36 to C-48. The pyrolytic cleavage of methyl mycolates (R(2)-CHOH-CH(R(1))-COOCH3), following the McLafferty rearrangement released fragment ions corresponding to, (a) the alpha-subunit, representing the fatty acid methyl ester (R(1)-CH2-COOCH3), methyl hexadecanoate, methyl tetradecanoate and methyl dodecanoate in decreasing order of relative intensity of peaks, and (b) the beta-subunit, representing the meroaldehyde moiety (R(2)-CHO). The saturated meroaldehyde species exhibited peaks representing meroaldehyde minus 18 mass units in which R(2) ranged from C19H39 to C31H63. The monunsaturated species exhibited peaks representing the meroaldehyde in which R(2) ranged from C19H37 to C31H61; peaks corresponding to meroaldehyde minus 18 mass units appeared only in the most abundant components, C29H57CHO, C27H53CHO, C25H49CHO and C31H61CHO, in a decreasing order of relative abundance. The diunsaturated species exhibited peaks essentially corresponding to meroaldehyde in which R(2) corresponded to C31H59 and C29H55; the latter displayed a relative intensity that was about one-half compared to that of the former. Fractions F-0, F-1 and F-2 showed a more intense pyrolytic fragmentation under CI-MS in contrast to results found under EI-MS. Therefore, peaks representing the alpha-subunit and the beta-subunit were more prominent than the ones representing the fragmentation of the hydrocarbon chain. Moreover, the beta-subunit of saturated species exhibited peaks corresponding to meroaldehyde plus hydrogen, and no dehydration of the beta-subunit occurred in this case. In turn, the beta-subunit of monounsaturated and diunsaturated species showed peaks representing both the meroaldehyde plus hydrogen and its dehydration product plus hydrogen. Thus, the presence of unsaturation in the meroaldehyde subunit of methyl mycolate facilitates appearance of dehydration fragment ions under chemical ionization procedure.

Fumaric acid monoethyl ester-functionalized poly(D,L-Lactide)/N-vinyl-2- pyrrolidone Resins for the preparation of tissue engineering scaffolds by stereolithography

Polymer networks were prepared by photocross-linking fumaric acid monoethyl ester (FAME) functionalized, three-armed poly(D,L-lactide) oligomers using Af-vinyl-2-pyrrolidone (NVP) as diluent and comonomer. The use of NVP together with FAME-functionalized oligomers resulted in copolymerization at high rates, and networks with gel contents in excess of 90 were obtained. The hydrophilicity of the poly(D,L-lactide) networks increases with increasing amounts of NVP, networks containing 50 wt of NVP absorbed 40 of water. As the amount of NVP was increased from 30 to 50 wt , the Young's modulus after equilibration in water decreased from 0.8 to 0.2 GPa, as opposed to an increase from 1.5 to 2.1 GPa in the dry state. Mouse preosteoblasts readily adhered and spread onto all prepared networks. Using stereolithography, porous structures with a well-defined gyroid architecture were prepared from these novel materials. This allows the preparation of tissue engineering scaffolds with optimized pore architecture and tunable material properties.

Influence of fatty acid structure on fuel properties of algae derived biodiesel

Physical and chemical properties of biofuel are influenced by structural features of fatty acid such as chain length, degree of unsaturation and branching of the chain. A simple and reliable calculation method to estimate fuel property is therefore needed to avoid experimental testing which is difficult, costly and time consuming. Typically in commercial biodiesel production such testing is done for every batch of fuel produced. In this study 9 different algae species were selected that were likely to be suitable for subtropical climates. The fatty acid methyl esters (FAMEs) of all algae species were analysed and the fuel properties like cetane number (CN), cold filter plugging point (CFPP), kinematic viscosity (KV), density and higher heating value (HHV) were determined. The relation of each fatty acid with particular fuel property is analysed using multivariate and multi-criteria decision method (MCDM) software. They showed that some fatty acids have major influences on the fuel properties whereas others have minimal influence. Based on the fuel properties and amounts of lipid content rank order is drawn by PROMETHEE-GAIA which helped to select the best algae species for biodiesel production in subtropical climates. Three species had fatty acid profiles that gave the best fuel properties although only one of these (Nannochloropsis oculata) is considered the best choice because of its higher lipid content.