Electrochemical current-sensing atomic force microscopy in conductive solutions

Insulated atomic force microscopy probes carrying gold conductive tips were fabricated and employed as bifunctional force and current sensors in electrolyte solutions under electrochemical potential control. The application of the probes for current-sensing imaging, force and current–distance spectroscopy as well as scanning electrochemical microscopy experiments was demonstrated.

Distributed active traction control system applied to the RoboCup middle size league

This work addresses the problem of traction control in mobile wheeled robots in the particular case of the RoboCup Middle Size League (MSL). The slip control problem is formulated using simple friction models for ISePorto Team robots with a differential wheel configuration. Traction was also characterized experimentally in the MSL scenario for relevant game events. This work proposes a hierarchical traction control architecture which relies in local slip detection and control at each wheel, with relevant information being relayed to a higher level responsible for global robot motion control. A dedicated one axis control embedded hardware subsystem allowing complex local control, high frequency current sensing and odometric information procession was developed. This local axis control board is integrated in a distributed system using CAN bus communications. The slipping observer was implemented in the axis control hardware nodes integrated in the ISePorto robots and was used to control and detect loss of for traction. %and to detect the ball in the kicking device. An external vision system was used to perform a qualitative analysis of the slip detection and observer performance results are presented.

Dipòsit i caracterització de capes primes orgàniques de P3HT:PCBM per a aplicacions fotovoltaiques

En un món on el ritme de la societat actual ens ha portat a considerar les energies enovables com a prioritat vital i necessària i en el que es preveu que la demanda energètica augmenti un 50% fins al 2030, l'interès en la recerca de materials emiconductors orgànics per aplicacions de captura solar, ha assolit un potencial enorme de cara al futur. Molts són el avantatges que presenten aquest tipus de materials en front als seus homòlegs inorgànics. La facilitat de fabricació, la utilització de materials més econòmics i amb menys impacte ambiental, així com la possibilitat de produir dispositius flexibles, són algunes de les atractives aracterístiques que presenten aquests materials. No obstant, certs inconvenients om les baixes eficiències energètiques dels dispositius, i la inestabilitat ambiental ue es tradueix en un temps de vida molt reduït, fan que encara s'hagi d'invertir sforç per aconseguir que aquests materials puguin ser utilitzats en el camp de la aptura d'energia solar. El material més prometedor fins a data d'avui és el P3HT:PCBM. Es tracta d'un sistema polímer:molècula lleugera, on el P3HT actua com a component donador del sistema i el PCBM actua com a component acceptor. Les propietats optoelectròniques i eficiències energètiques de combinats orgànics P3HT:PCBM epèn en gran mesura de la seva morfologia i microestructura. Paràmetres com la proporció entre els components, el dissolvent utilitzat en la dissolució, així com 'aplicació de determinats tractaments tèrmics afecten de forma crítica a la seva orfologia. Durant el present treball s'han utilitzat diverses tècniques de caracterització per a estudiar determinades propietats que presenten aquest tipus de aterials. Entre les tècniques experimentals utilitzades hi trobem la microscòpia FM, l'espectroscòpia Raman i la conductimetria AFM o current sensing AFM CS-AFM). Els experiments en temps real durant l'escalfament de capes primes 3HT:PCBM, mostren que el P3HT pateix una cristal·lització al voltant dels 140ºC, permetent el reordenament de les molècules i un millor solapament del sorbitals [pi]-[pi]*, que resulta en un increment del transport de forats a través de la fase donadora del material. Paralel·lament, entre els 80-120ºC, el material també presenta determinats canvis tant en el comportament dels enllaços, com en la cristal·linitat del material, provocant una quasi transició de fase que atribuïm a la transició vitrea del material. Per altra banda, experiments amb conductimetria AFM realitzats en sistemes P3HT:HDPE mostren un signicatiu augment en la eva estabilitat ambiental, que es tradueix en un augment del temps de vida, sense una pèrdua considerable en els seus valors de conducció. Tot i la combinació del P3HT amb proporcions de polímers aïllants de fins al 80%, el sistema és capaç de no perdre la capacitat de transport gràcies a la formació de fases i dominis rics en P3HT. El present treball posa de manifest que ens trobem davant d'una tecnologia emergent i que nous estudis i esforços en la recerca d'aquest tipus materials és fonamental per aconseguir nous resultats i posicionar als materials semiconductors orgànics com una alternativa viable en el camp dels dispositus fotovoltaics. Assumint dades procedents de la tecnologia actual utilitzada en aquest tipus de materials, estudis i avaluacions ambientals i econòmiques mostren que petits increments tant en les eficiències com en el temps de vida de dispositius basats en aterials orgànics, posicionarien a aquest material com a alternativa totalment viable en el mercat fotovoltaic d'un futur proper.

Transport properties across the La2/3Ca1/3MnO3/SrTiO3 heterointerface

The transport properties across La2/3Ca1/3MnO3/SrTiO3 (LCMO/STO) heterostructures with different thicknesses of the STO insulating barrier have been studied by using atomic force microscopy measurements in the current sensing (CS) mode. To avoid intrinsic problems of the CS method we have developed a nanostructured contact geometry of Au dots. The conduction process across the LCMO/STO interface exhibits the typical features of a tunneling process.

Virranmittausanturin suunnittelu ja simulointi taajuusmuuttajakäyttöön

Virranmittausantureita tarvitaan monenlaisissa käyttökohteissa, joissa ne mittaavat sekä virran suuruuttaettä laatua ja toimivat osana niiden säätelyjärjestelmää. Virranmittausantureita tarvitaan myös vikatilanteiden määrittämiseen erilaisissa suojauspiireissä. Taajuusmuuttajissa virranmittaus on hyvin tärkeää ja suurista virroista sekä taajuuksista johtuen se täytyy suunnitella huolella. Tässä diplomityössä käsitellään ja tutkitaan eri virranmittausmenetelmiä, joiden avulla taajuusmuuttajan luotettava virranmittaus voidaan toteuttaa. Työssä tutkitaan eri menetelmiä virranmittauksen toteuttamiseksi, minkä jälkeen niistä valitaan sopiva menetelmä ja tutkitaan sen eri toteutusvaihtoehtoja. Sopivan toteutusvaihtoehdon valinnan jälkeen työssä suunnitellaan oma virranmittausanturi, joka sopii nimenomaisesti taajuusmuuttajakäyttöön. Suunnitellun anturin ominaisuuksia tutkitaan lopuksi simuloimalla, jonka jälkeen arvioidaan sen soveltumista käytännön sovelluksiin sekä arvioidaan erilaisia keinoja sen parantamiseksi.

Relay protection in active distribution networks

Increasingly growing share of distributed generation in the whole electrical power system’s generating system is currently a worldwide tendency, driven by several factors, encircling mainly difficulties in refinement of megalopolises’ distribution networks and its maintenance; widening environmental concerns adding to both energy efficiency approaches and installation of renewable sources based generation, inherently distributed; increased power quality and reliability needs; progress in IT field, making implementable harmonization of needs and interests of different-energy-type generators and consumers. At this stage, the volume, formed by system-interconnected distributed generation facilities, have reached the level of causing broad impact toward system operation under emergency and post-emergency conditions in several EU countries, thus previously implementable approach of their preliminary tripping in case of a fault, preventing generating equipment damage and disoperation of relay protection and automation, is not applicable any more. Adding to the preceding, withstand capability and transient electromechanical stability of generating technologies, interconnecting in proximity of load nodes, enhanced significantly since the moment Low Voltage Ride-Through regulations, followed by techniques, were introduced in Grid Codes. Both aspects leads to relay protection and auto-reclosing operation in presence of distributed generation generally connected after grid planning and construction phases. This paper proposes solutions to the emerging need to ensure correct operation of the equipment in question with least possible grid refinements, distinctively for every type of distributed generation technology achieved its technical maturity to date and network’s protection. New generating technologies are equivalented from the perspective of representation in calculation of initial steady-state short-circuit current used to dimension current-sensing relay protection, and widely adopted short-circuit calculation practices, as IEC 60909 and VDE 0102. The phenomenon of unintentional islanding, influencing auto-reclosing, is addressed, and protection schemes used to eliminate an sustained island are listed and characterized by reliability and implementation related factors, whereas also forming a crucial aspect of realization of the proposed protection operation relieving measures.

A 12 kW three-phase low THD rectifier with high-frequency isolation and regulated DC output

A robust 12 kW rectifier with low THD in the line currents, based on an 18-pulse transformer arrangement with reduced kVA capacities followed by a high-frequency isolation stage is presented in this work. Three full-bridge (buck-based) converters are used to allow galvanic isolation and to balance the dc-link currents, without current sensing or current controller. The topology provides a regulated dc output with a very simple and well-known control strategy and natural three-phase power factor correction. The phase-shift PWM technique, with zero-voltage switching is used for the high-frequency dc-dc stage. Analytical results from Fourier analysis of winding currents and the vector diagram of winding voltages are presented. Experimental results from a 12 kW prototype are shown in the paper to verify the efficiency, robustness and simplicity of the command circuitry to the proposed concept.

A new three-phase low THD power supply with high-frequency isolation and 60V/200A regulated DC output

This work proposes a new isolated high power factor 12kW power supply based on an 18-pulse transformer arrangement. Three full-bridge converters are used for isolation and to balance the DC-link currents, without current sensing or a current controller. The topology provides a regulated DC output with a very simple control strategy. Simulation and experimental results are presented in this paper.

Desenvolvimento de sistema de aquisição e processamento para aplicações em qualidade de energia

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Advanced CMOS Interfaces for Bio-Nanosensors

The improvement of devices provided by Nanotechnology has put forward new classes of sensors, called bio-nanosensors, which are very promising for the detection of biochemical molecules in a large variety of applications. Their use in lab-on-a-chip could gives rise to new opportunities in many fields, from health-care and bio-warfare to environmental and high-throughput screening for pharmaceutical industry. Bio-nanosensors have great advantages in terms of cost, performance, and parallelization. Indeed, they require very low quantities of reagents and improve the overall signal-to-noise-ratio due to increase of binding signal variations vs. area and reduction of stray capacitances. Additionally, they give rise to new challenges, such as the need to design high-performance low-noise integrated electronic interfaces. This thesis is related to the design of high-performance advanced CMOS interfaces for electrochemical bio-nanosensors. The main focus of the thesis is: 1) critical analysis of noise in sensing interfaces, 2) devising new techniques for noise reduction in discrete-time approaches, 3) developing new architectures for low-noise, low-power sensing interfaces. The manuscript reports a multi-project activity focusing on low-noise design and presents two developed integrated circuits (ICs) as examples of advanced CMOS interfaces for bio-nanosensors. The first project concerns low-noise current-sensing interface for DC and transient measurements of electrophysiological signals. The focus of this research activity is on the noise optimization of the electronic interface. A new noise reduction technique has been developed so as to realize an integrated CMOS interfaces with performance comparable with state-of-the-art instrumentations. The second project intends to realize a stand-alone, high-accuracy electrochemical impedance spectroscopy interface. The system is tailored for conductivity-temperature-depth sensors in environmental applications, as well as for bio-nanosensors. It is based on a band-pass delta-sigma technique and combines low-noise performance with low-power requirements.

Progetto e realizzazione di un sistema di test per sensori a effetto hall a banda larga

Un ambito di largo interesse nel campo dell’elettronica, è quello delle misure di corrente a larga banda, in cui la richiesta per sistemi a basso costo è aumentata sensibilmente nel corso del tempo. La causa di questo interessamento è dovuto al più frequente utilizzo di sistemi switched power ad alta frequenza, che necessitano di sensori di correnti isolati e ad alte prestazioni. L’intero lavoro prende in considerazione un sensore di nuova generazione per le misure di corrente, capace di raggiungere prestazioni oltre lo stato dell’arte. L’elaborato presentato vede, quindi, come obiettivo la creazione di un setup stabile per effettuare misure sui chip prodotti. Partendo dallo studio di fattibilità, della componentistica necessaria e dei compromessi per mantenere i costi, si giunge ad una soluzione flessibile e adatta alle misurazioni richieste. L’elaborato partirà con una introduzione sugli effetti fisici e la descrizione del componente fondamentale, passando a test funzionali effettuati su setup provvisori atti a ottenere informazioni basilari per la prosecuzione del lavoro. Infine verranno concepite e realizzate due schede a circuiti stampati per rispondere alle esigenze di progetto.

Utilising presence in places to support mobile interaction

Physical places are given contextual meaning by the objects and people that make up the space. Presence in physical places can be utilised to support mobile interaction by making access to media and notifications on a smartphone easier and more visible to other people. Smartphone interfaces can be extended into the physical world in a meaningful way by anchoring digital content to artefacts, and interactions situated around physical artefacts can provide contextual meaning to private manipulations with a mobile device. Additionally, places themselves are designed to support a set of tasks, and the logical structure of places can be used to organise content on the smartphone. Menus that adapt the functionality of a smartphone can support the user by presenting the tools most likely to be needed just-in-time, so that information needs can be satisfied quickly and with little cognitive effort. Furthermore, places are often shared with people whom the user knows, and the smartphone can facilitate social situations by providing access to content that stimulates conversation. However, the smartphone can disrupt a collaborative environment, by alerting the user with unimportant notifications, or sucking the user in to the digital world with attractive content that is only shown on a private screen. Sharing smartphone content on a situated display creates an inclusive and unobtrusive user experience, and can increase focus on a primary task by allowing content to be read at a glance. Mobile interaction situated around artefacts of personal places is investigated as a way to support users to access content from their smartphone while managing their physical presence. A menu that adapts to personal places is evaluated to reduce the time and effort of app navigation, and coordinating smartphone content on a situated display is found to support social engagement and the negotiation of notifications. Improving the sensing of smartphone users in places is a challenge that is out-with the scope of this thesis. Instead, interaction designers and developers should be provided with low-cost positioning tools that utilise presence in places, and enable quantitative and qualitative data to be collected in user evaluations. Two lightweight positioning tools are developed with the low-cost sensors that are currently available: The Microsoft Kinect depth sensor allows movements of a smartphone user to be tracked in a limited area of a place, and Bluetooth beacons enable the larger context of a place to be detected. Positioning experiments with each sensor are performed to highlight the capabilities and limitations of current sensing techniques for designing interactions with a smartphone. Both tools enable prototypes to be built with a rapid prototyping approach, and mobile interactions can be tested with more advanced sensing techniques as they become available. Sensing technologies are becoming pervasive, and it will soon be possible to perform reliable place detection in-the-wild. Novel interactions that utilise presence in places can support smartphone users by making access to useful functionality easy and more visible to the people who matter most in everyday life.

Eddy current testing system with scanning probe head having parallel and normal sensing coils

An eddy current testing system consists of a multi-sensor probe, a computer and a special expansion card and software for data-collection and analysis. The probe incorporates an excitation coil, and sensor coils; at least one sensor coil is a lateral current-normal coil and at least one is a current perturbation coil.

Eddy current testing program with scanning probe head having parallel and normal sensing coils

An eddy current testing system consists of a multi-sensor probe, computer and a special expansion card and software for data collection and analysis. The probe incorporates an excitation coil, and sensor coils; at least one sensor coil is a lateral current-normal coil and at least one is a current perturbation coil.