Study of sunless tanning formulas using molted snake skin as an alternative membrane model

Sunless tanning formulas have become increasingly popular in recent years for their ability to give people convincing tans without the dangers of skin cancer. Most sunless tanners currently on the market contain dihydroxyacetone (DHA), a keto sugar with three carbons. The temporary pigment provided by these formulasis designed to resemble a UV-induced tan. This study evaluated the effectiveness of carbomer gels and cold process self emulsifying bases on skin pigmentation, using different concentrations of a chemical system composed of DHA and N-acetyl tyrosine, which are found in moulted snake skins and their effectiveness was tested by Mexameter (R) MX 18. Eight different sunless tanning formulas were developed, four of which were gels and four of which were emulsions (base, base plus 4.0%, 5.0% and 6.0% (w/w) of a system of DHA and N-acetyl tyrosine). Tests to determine the extent of artificial tanning were done by applying 30 mg cm(-2) of each formula onto standard sizes of moulted snake skin (2.0 cm x 3.0 cm). A Mexameter (R) MX 18 was used to evaluate the extent of coloration in the moulted snake skin at T(0) (before the application) and after 24, 48, 72, 168, 192 and 216 h. The moulted snake skins can be used as an alternative membrane model for in vitro sunless tanning efficacy tests due to their similarity to the human stratum corneum. The DHA concentration was found to influence the initiation of the pigmentation in both sunless tanning systems (emulsion and gel) as well as the time required to increases by a given amount on the tanning index. In the emulsion system, the DHA concentration also influenced the final value on the tanning index. The type of system (emulsion or gel) has no influence on the final value in the tanning index after 216 h for samples with the same DHA concentration.

Levylämmönsiirtimen mitoitus ja optimointi erityisesti lämpöpumpuissa

Työn tavoitteena on laatia käsikirjamainen läpileikkaus levylämmönsiirtimen rakenteesta ja käytöstä lämpöpumppulaitteistoissa. Kylmäprosessin tarkastelun lisäksi on eri lähteistä haettu yhtälöitä lämmönsiirron ja painehäviönlaskentaan. Lähdeaineistona on käytetty lämmönsiirron oppikirjoja, joiden lisäksi on käyty läpi suuri joukko tieteellisen tutkimuksen julkaisemia tutkimusraportteja levylämmönsiirtimen mitoituksesta erilaisissa käyttökohteissa. Oppikirjoissa ei ole esitetty varsinaisesti levylämmönsiirtimen laskentamenetelmiä, vaan niissä esitetään lämmönsiirron perusyhtälöt. Varsinainen lämmönsiirtolevyprofiilin laskentaan perustuva lähdeaineisto on löytynyt lämmönsiirtoon erikoistuneista julkaisuista. Lämmönsiirto tapahtuu aina kuumemmasta kylmempään tilaan. Lämmönsiirto eri virtausaineiden välillä toteutetaan lämmönsiirtimien avulla. Lämmönsiirrintyyppejä on olemassa lukuisia, joista yksi yleisesti käytetty tyyppi on levylämmönsiirrin. Tässä konstruktiossa on mahdutettu paljon lämmönsiirtopintaa ulkomitoiltaan pieneen tilaan. Tämä siirrintyyppi on eduksi silloin, kun virtaavat aineet ovat puhtaita ja niillä ei ole likaavaa vaikutusta lämmönsiirtopinnoille. Lämpöpumpulla tarkoitetaan laitetta, jolla voidaan käyttää hyödyksi lämmönlähteen matalaa lämpötilatasoa nostamalla lämpötilatasoa kompressorin puristustyön avulla korkeampaan lämpötilatasoon. Lämpöpumppulaitteiston toiminta perustuu kylmäprosessin toimintaan. Kylmäprosessin läpikäynti auttaa lukijaa hahmottamaan, millainen prosessi on kysymyksessä ja mitä komponentteja liittyy kylmäprosessiin. Tässä diplomityössä esitetyt yhtälöt antavat suuntaa, millä tavalla levylämmönsiirtimien ominaisuuksia voidaan laskea ja mitkä tekijät vaikuttavat siirtimien mitoittamiseen. Tarkemmat vaihdinkohtaiset laskentakorrelaatiot muotoutuvat vasta sitten, kun valmis tuote on testattu laboratorio-olosuhteissa ja siitä on saatu lämpötila-, virtaus- ja painesuhteet selville. Tämän jälkeen voidaan mittaustuloksiin perustuen rakentaa matemaattinen malli, jolla laskennallisesti määritelläänvaihtimien ominaisuudet. Lisäksi on esitetty yleisiä tapoja, joilla voidaan määritellä lämmönsiirtimien lämpöpintoja.

Kaksivaiheisen lämmöntalteenottoprosessin soveltuvuus poistoilmanvaihtoiseen kerrostaloon

Diplomityön tavoitteena oli tarkastella perinteistä poistoilmanvaihtoa käyttävän kerrostalon lämmöntalteenottoa menetelmällä, joka yhdistää poistoilmalämpöpumpun ja maalämpöpumpun toiminnat. Nostamalla maalämpöpumpulle tulevan veden lämpötilaa saadaan nostettua järjestelmän COP-arvoa, jolla on suuri merkitys laitteen energiateknisen toiminnan kannalta. Laskelmat tehtiin Suomen rakennusmääräyskokoelman ohjeiden mukaisesti käyttämällä MX6- energiaohjelmaa sekä simuloimalla kylmäprosessia. Tulokset yhdistettiin taulukkolaskentaohjelmassa, ja näin saatiin teoreettinen säästölaskelma, joka perustuu arvioituun kuukausittaiseen energian keskikulutukseen, ts. taseeseen. Työssä todettiin, että poistoilmalämpöpumppu saattaisi kuluttaa poistoilman lämmöntalteenotossa liikaa sähköä, työssä tarkoitetulla tavalla. Kulutus olisi enemmän kuin maalämpöpumpun COP-arvon parantamisella saatava rahallinen hyöty. Koneellisen poistoilman välittämän energian tehokas käyttö on kuitenkin yksi mahdollisuus säästää maalämpöreikien poraamisessa, jos kerrostalossa harkittaisiin kokonaan maalämpöön siirtymistä.

Ileal amino acid digestibility in canola meals from yellow- and black-seeded Brassica napus and Brassica juncea fed to growing pigs

Twelve ileal cannulated pigs (30.9 ± 2.7 kg) were used to determine the apparent (AID) and standardized (SID) ileal digestibility of protein and AA in canola meals (CM) derived from black- (BNB) and yellow-seeded (BNY) Brassica napus canola and yellow-seeded Brassica juncea (BJY). The meals were produced using either the conventional pre-press solvent extraction process (regular meal) or a new, vacuum-assisted cold process of meal de-solventization (white flakes) to provide 6 different meals. Six cornstarch-based diets containing 35% canola meal as the sole source of protein in a 3 (variety) × 2 (processing) factorial arrangement were randomly allotted to pigs in a 6 × 7 incomplete Latin square design to have 6 replicates per diet. A 5% casein diet was fed to estimate endogenous AA losses. Canola variety and processing method interacted for the AID of DM (P = 0.048), N (P = 0.010), and all AA (P < 0.05), except for Arg, Lys, Phe, Asp, Glu, and Pro. Canola variety affected or tended to affect the AID of most AA but had no effect on the AID of Lys, Met, Val, Cys, and Pro, whereas processing method had an effect on only Lys and Asp and tended to affect the AID of Thr, Gly and Ser. The effects of canola variety, processing method, and their interaction on the SID values for N and AA followed a similar pattern as for AID values. For the white flakes, SID of N in BJY (74.2%) was lower than in BNY and BNB, whose values averaged 78.5%; however, among the regular meals, BJY had a greater SID value for N than BNY and BNB (variety × processing, P = 0.015). For the white flakes, the SID of Ile (86.4%), Leu (87.6%), Lys (88.9%), Thr (87.6%) and Val (84.2%) in BNB were greater than BNY and BJY. Opposite results were observed for the regular processing, with SID of Lys (84.1%), Met (89.5%), Thr (84.1%), and Val (83.6%) being greater in BJY, followed by BNB and BNY(variety × processing, P < 0.057). The SID of Met was greatest for the white flakes (90.2%) but least for the regular processing (83.0%) in BNY (variety × processing, P < 0.057). It was concluded that the AID and SID of N and AA of the CM tested varied according to canola variety and the processing method used. Overall, the SID values for Ile, Leu, Lys, Met, Thr, and Val averaged across CM types and processing methods were 81.8, 82.6, 83.4, 85.9, 80.8, and 78.4%, respectively.

Development of a Mix Design Process for Cold-in-Place Rehabilitation Using Foamed Asphalt, December 2005

Report by Iowa Department of Transportation about pavements materials.

Validation of the New Mix Design Process for Cold In-Place Rehabilitation Using Foamed Asphalt, 2007

Asphalt pavement recycling has grown dramatically over the last few years as a viable technology to rehabilitate existing asphalt pavements. Iowa's current Cold In-place Recycling (CIR) practice utilizes a generic recipe specification to define the characteristics of the CIR mixture. As CIR continues to evolve, the desire to place CIR mixture with specific engineering properties requires the use of a mix design process. A new mix design procedure was developed for Cold In-place Recycling using foamed asphalt (CIR-foam) in consideration of its predicted field performance. The new laboratory mix design process was validated against various Reclaimed Asphalt Pavement (RAP) materials to determine its consistency over a wide range of RAP materials available throughout Iowa. The performance tests, which include dynamic modulus test, dynamic creep test and raveling test, were conducted to evaluate the consistency of a new CIR-foam mix design process to ensure reliable mixture performance over a wide range of traffic and climatic conditions. The “lab designed” CIR will allow the pavement designer to take the properties of the CIR into account when determining the overlay thickness.

Effect of cold-working process on corrosion behavior of copper

The microstructure, microhardness, texture and corrosion resistance of cold-swaged and cold-wiredrawn copper rods were evaluated. Elongated grains along the deformation direction were observed for both materials and the width of these grains decreased with the increase of reduction in area. Wiredrawn copper rods have higher microhardness than the swaged rods for the same reduction in area. The copper grains in both cold-worked rods presented a preferential orientation in the [1 1 0] crystallographic direction but this trend was more pronounced for swaged rods. The corrosion resistance of wiredrawn copper rods investigated in H(2)SO(4) solutions was lower than that of swaged rods, and for both deformed materials the corrosion resistance decreased with the deformation degree. (C) 2011 Elsevier Ltd. All rights reserved.

Corrosion Characteristics And Mechanical Properties Of Aluminum Coatings Applied By The Cold Spray Process

Aluminum coatings were applied to 2024-T3 and 7075-T6 aluminum alloys via the Cold Spray process. The coatings were applied to substrateswith various surface preparation and Cold Spray carrier gas combinations. Some samples were coated with an additional sealant with and without a chromate conversion layer. An exhaustive corrosion analysis was then performed which utilized a number of long termand accelerated tests in order to characterize the corrosion protection of the coatings.

Computer simulation for tube-making by the cold roll-forming process

The conventional design of forming rolls depends heavily on the individual skill of roll designers which is based on intuition and knowledge gained from previous work. Roll design is normally a trial an error procedure, however with the progress of computer technology, CAD/CAM systems for the cold roll-forming industry have been developed. Generally, however, these CAD systems can only provide a flower pattern based on the knowledge obtained from previously successful flower patterns. In the production of ERW (Electric Resistance Welded) tube and pipe, the need for a theoretical simulation of the roll-forming process, which can not only predict the occurrence of the edge buckling but also obtain the optimum forming condition, has been recognised. A new simulation system named "CADFORM" has been devised that can carry out the consistent forming simulation for this tube-making process. The CADFORM system applied an elastic-plastic stress-strain analysis and evaluate edge buckling by using a simplified model of the forming process. The results can also be visualised graphically. The calculated longitudinal strain is obtained by considering the deformation of lateral elements and takes into account the reduction in strains due to the fin-pass roll. These calculated strains correspond quite well with the experimental results. Using the calculated strains, the stresses in the strip can be estimated. The addition of the fin-pass roll reduction significantly reduces the longitudinal compressive stress and therefore effectively suppresses edge buckling. If the calculated longitudinal stress is controlled, by altering the forming flower pattern so it does not exceed the buckling stress within the material, then the occurrence of edge buckling can be avoided. CADFORM predicts the occurrence of edge buckling of the strip in tube-making and uses this information to suggest an appropriate flower pattern and forming conditions which will suppress the occurrence of the edge buckling.

Modified Steels for Cold-Forming U-Bolts Used In Leaf Springs Systems

In this work, a low alloy steel and a fabrication process were developed to produce U-Bolts for commercial vehicles. Thus, initially five types of no-heat treated steel were developed with different additions of chrome, nickel, and silicon to produce strain hardening effect during cold-forming processing of the U-Bolts, assuring the required mechanical properties. The new materials exhibited a fine perlite and ferrite microstructure due to aluminum and vanadium additions, well known as grain size refiners. The mechanical properties were evaluated in a servo-hydraulic test machine system-MTS 810 according to ASTM A370-03; E739 and E08m-00 standards. The microstructure and fractography analyses of the cold-formed steels were performed by using optical and scanning electronic microscope techniques. To evaluate the performance of the steels and the production process, fatigue tests were carried out under load control (tensile-tensile), R = 0.1 and f = 30 Hz. The Weibull statistic methodology was used for the analysis of the fatigue results. At the end of this work the 0.21% chrome content steel, Alloy 2, presented the best fatigue performance.

Importance of considering a material micro-failure criterion in the numerical modelling of the shot peening process applied to parabolic leaf springs

Shot peening is a cold-working mechanical process in which a shot stream is propelled against a component surface. Its purpose is to introduce compressive residual stresses on component surfaces for increasing the fatigue resistance. This process is widely applied in springs due to the cyclical loads requirements. This paper presents a numerical modelling of shot peening process using the finite element method. The results are compared with experimental measurements of the residual stresses, obtained by the X-rays diffraction technique, in leaf springs submitted to this process. Furthermore, the results are compared with empirical and numerical correlations developed by other authors.

Manipulation of quantum state transfer in cold Rydberg atom collisions

We investigate the role of the dc Stark effect in multilevel pairwise interactions between cold Rydberg atoms. We have observed the decay of nD + nD quasi-molecules by detecting the products in the (n + 2) P state after pulsed excitation for 29 <= n <= 41. The decay rate can be manipulated with a dc electric field and requires a consideration of the multilevel nature of the process to explain the observations. The time dependence of the (n + 2) P signal is found to support a time-dependent picture of the dynamics.

Adaptation for tandem cold mill models

The ideal conditions for the operation of tandem cold mills are connected to a set of references generated by models and used by dynamic regulators. Aiming at the optimization of the friction and yield stress coefficients an adaptation algorithm is proposed in this paper. Experimental results obtained from an industrial cold rolling mill are presented. (C) 2008 Elsevier B.V. All rights reserved.

Adequacy of Cold Rolling Models to Upgrade Set-up Generation Systems

This paper presents two strategies for the upgrade of set-up generation systems for tandem cold mills. Even though these mills have been modernized mainly due to quality requests, their upgrades may be made intending to replace pre-calculated reference tables. In this case, Bryant and Osborn mill model without adaptive technique is proposed. As a more demanding modernization, Bland and Ford model including adaptation is recommended, although it requires a more complex computational hardware. Advantages and disadvantages of these two systems are compared and discussed and experimental results obtained from an industrial cold mill are shown.

Review of Contact and Dynamic Phenomena in Cold Roll Forming

This review reflects the state of the art in study of contact and dynamic phenomena occurring in cold roll forming. The importance of taking these phenomena into account is determined by significant machine time and tooling costs spent on worn out forming rolls replacement and equipment adjustment in cold roll forming. Predictive modelling of the tool wear caused by contact and dynamic phenomena can reduce the production losses in this technological process.