Clay ratio as a tracer to assess the origin of soil-derived dust

IEECAS SKLLQG

Sedimentary facies, clay mineralogy and geochemistry of the Paleogene sediments of ODP Site 105-647

Claystones immediately overlying the early Eocene age ocean-floor basalt, cored at Ocean Drilling Program (ODP) Site 647, underwent hydrothermal and thermal alterations originating from the basalt, which resulted in changes in both the mineralogical and chemical composition of the sediments. Chlorites and higher magnesium and iron concentrations were found in the lowermost sediment sequence. Upcore, changes in the bulk chemical composition of the sediments become smaller, when compensated for variations in the carbonate content originating from biogenic and authigenic components. Chlorite disappears upcore, but still only part of the swelling clay minerals have survived the thermal influence. Thirty meters above the basalt, the clay mineralogy and chemical composition become uniform throughout the Paleogene section. Iron-rich smectites (i.e., nontronitic types), totally dominate the clay mineral assemblage. Biogenic components, responsible for the dominant part of the calcite and cristobalite contents, vary in amount in the upper part, and so do the authigenic carbonate and sulfide contents. Detrital components, such as kaolinite, illite, quartz, and feldspars, make up a very small proportion of the sediment record. The nontronitic smectites are believed to be authigenic, formed by a supply of iron from the continuous formation of ocean-floor basalt in the ridge area that reacted with the detrital and biogenic silicates and alumina silicates.

Clay mineral distribution in sediment core AND-2A

Clay mineral assemblages in sediments from ANDRILL drill core AND-2A were used to reconstruct the Neogene palaeoenvironment. For the first time a clay mineral data set can be presented for southern McMurdo Sound, Ross Sea, Antarctica, that covers an expanded and fairly continuous Lower and Middle Miocene section. Although the occurrence of some authigenic smectites, zeolites and opal-CT documents diagenetic processes, the clay mineral assemblages allow a subdivision of the core into three intervals that reflect changes in provenance and volcanic activity. Interval I (1000-440 mbsf, 20.0-16.5 Ma) is characterised by a dominant sediment source in the Transantarctic Mountains. Frequent and short-term changes in the illite and smectite concentrations were caused by the influx of volcanic sediment components from southern McMurdo Sound and by diagenesis. Interval II (440-225 mbsf, 16.5-15.0 Ma) has much more uniform illite and smectite contents. The assemblage is derived from the Transantarctic Mountains. Interval III (225-0 mbsf, 15.0-0 Ma, containing major hiatuses) shows a distinctly enhanced volcanic influence and sediment components that come from the south of McMurdo Sound. The AND-2A clay mineral assemblages indicate persistent physical weathering conditions and do not mirror the Mid-Miocene Climatic Optimum. They indicate that the climatic changes were probably not strong enough to cause a modification in the weathering regime on the Antarctic continent.

Nanostructured metal oxides as adsorbents and photocatalysts

This research underlines the extensive application of nanostructured metal oxides in environmental systems such as hazardous waste remediation and water purification. This study tries to forge a new understanding of the complexity of adsorption and photocatalysis in the process of water treatment. Sodium niobate doped with a different amount of tantalum, was prepared via a hydrothermal reaction and was observed to be able to adsorb highly hazardous bivalent radioactive isotopes such as Sr2+ and Ra2+ions. This study facilitates the preparation of Nb-based adsorbents for efficiently removing toxic radioactive ions from contaminated water and also identifies the importance of understanding the influence of heterovalent substitution in microporous frameworks. Clay adsorbents were prepared via a two-step method to remove anionic and non-ionic herbicides from water. Firstly, layered beidellite clay was treated with acid in a hydrothermal process; secondly, common silane coupling agents, 3-chloro-propyl trimethoxysilane or triethoxy silane, were grafted onto the acid treated samples to prepare the adsorption materials. In order to isolate the effect of the clay surface, we compared the adsorption property of clay adsorbents with ƒ×-Al2O3 nanofibres grafted with the same functional groups. Thin alumina (£^-Al2O3) nanofibres were modified by the grafting of two organosilane agents 3-chloropropyltriethoxysilane and octyl triethoxysilane onto the surface, for the adsorptive removal of alachlor and imazaquin herbicides from water. The formation of organic groups during the functionalisation process established super hydrophobic sites along the surfaces and those non-polar regions of the surfaces were able to make close contact with the organic pollutants. A new structure of anatase crystals linked to clay fragments was synthesised by the reaction of TiOSO4 with laponite clay for the degradation of pesticides. Based on the Ti/clay ratio, these new catalysts showed a high degradation rate when compared with P25. Moreover, immobilized TiO2 on laponite clay fragments could be readily separated out from a slurry system after the photocatalytic reaction. Using a series of partial phase transition methods, an effective catalyst with fibril morphology was prepared for the degradation of different types of phenols and trace amount of herbicides from water. Both H-titanate and TiO2-(B) fibres coated with anatase nanocrystal were studied. When compared with a laponite clay photocatalyst, it was found that anatase dotted TiO2-(B) fibres prepared by a 45 h hydrothermal treatment followed by calcination were not only superior in performance in photocatalysis but could also be readily separated from a slurry system after photocatalytic reactions. This study has laid the foundation for the development of the ability to fabricate highly efficient nanostructured solids for the removal of radioactive ions and organic pollutants from contaminated water. These results now seem set to contribute to the development of advanced water purification devices in the future. These modified nanostructured materials with unusual properties have broadened their application range beyond their traditional use as adsorbents, to also encompass the storage of nuclear waste after concentrating from contaminated water.

Simultaneous adsorption of Cd(II) and phosphate on Al13 pillared montmorillonite

Al13 pillared montmorillonites (AlPMts) prepared with different Al/clay ratios were used to remove Cd(II) and phosphate from aqueous solution. The structure of AlPMts was characterized by X-ray diffraction (XRD), Thermogravimetric analysis (TG), and N2 adsorption–desorption. The basal spacing, intercalated amount of Al13 cations, and specific surface area of AlPMts increased with the increase of the Al/clay ratio. In the single adsorption system, with the increase of the Al/clay ratio, the adsorption of phosphate on AlPMts increased but that of Cd(II) decreased. Significantly enhanced adsorptions of Cd(II) and phosphate on AlPMts were observed in a simultaneous system. For both contaminants, the adsorption of one contaminant would increase with the increase of the initial concentration of the other one and increase in the Al/clay ratio. The enhancement of the adsorption of Cd(II) was much higher than that of phosphate on AlPMt. This suggests that the intercalated Al13 cations are the primary co-adsorption sites for phosphate and Cd(II). X-ray photoelectron spectroscopy (XPS) indicated comparable binding energy of P2p but a different binding energy of Cd3d in single and simultaneous systems. The adsorption and XPS results suggested that the formation of P-bridge ternary surface complexes was the possible adsorption mechanism for promoted uptake of Cd(II) and phosphate on AlPMt.

Properties of lime stabilised steam-cured blocks for masonry

The paper addresses certain issues pertaining to the technology of lime-stabilised steam-cured blocks used for masonry construction. Properties of lime-stabilised steam-cured blocks using expansive soils and tank bed soils have been examined. Influence of parameters like steam curing period, lime content and fly ash content on wet strength of blocks is studied. Steam curing of lime stabilised blocks at 80degreesC for about 20 hours at atmospheric pressure leads to considerably higher strengths when compared with curing under wet cloth at ambient temperatures. Clay-fly ash fractions of the mix control the optimum lime content yielding maximum strength. Long-term strength behaviour of steam-cured blocks has been monitored. The results indicate a favourable lime-clay ratio for stable long-term strength. A small-scale steam cured block production system has been designed and implemented to construct a load bearing masonry structure, thus demonstrating the potential of steam-cured block as a material for masonry construction.

Caracteristicas gerais e classificacao de solos basalticos da regiao Central do Estado de Sao Paulo.

Giving a special emphasis on soil classification relative to their positions in the landscape, five soil profiles in the Barra Bonita-Jau area were characterized through morphological, granulometric and chemical routine soil analysis. It was observed that the soil structure gradually changes from strong blocks with cutans (lowlands and smooth parts - Jau). In this direction, the silt/clay ratio and the base saturation is reduced, and the aluminium saturation increases. -from English summary

Superfícies geomórficas e variabilidade de latossolos em uma vertente sobre arenito-basalto em Jaboticabal (SP)

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Influência da razão Al/argila no processo de pilarização de esmectita

As amostras de esmectita do estado do Pará, Amazônia, Brasil foram caracterizadas utilizando XRD, ²⁷Al MAS NMR, FTIR e análise textural por curvas isotérmicas de adsorção-dessorção de nitrogênio. Na produção das argilas pilarizadas foi usado como íon intercalante, o Al₁₃ (o íon de keggin), obtido pela reação das soluções AlC_l36H₂O/NaOH, com razão molar OH/Al=2. Foram adotadas as proporções (Al/Argila): 5, 10, 20 e 25 meq/g de argila, com intercalação em 25 ºC, durante as 3 h e calcinada a 450 ºC (temperatura adequada da calcinação). O resultado mostrou que o processo de pilarização aumentou o espaçamento basal da argila natural de 14,02 para 18,84 Å e a área superficial de 44,30 para 198,03 m²/g (Al/Argila=25meq/g de argila, pH=4). O material preparado com relação Al/Argila=25meq/g de argila mostrou a incorporação máxima de Al. A estabilidade térmica da argila natural foi melhorada pelo procedimento de pilarização.

Estratigrafia do Andar Alagoas na sub-bacia do Tucano Norte, Bahia

Pós-graduação em Geociências e Meio Ambiente - IGCE