Minimizing Circulating Current in Parallel-Connected Photovoltaic Inverters

Parallel-connected photovoltaic inverters are required in large solar plants where it is not economically or technically reasonable to use a single inverter. Currently, parallel inverters require individual isolating transformers to cut the path for the circulating current. In this doctoral dissertation, the problem is approached by attempting to minimize the generated circulating current. The circulating current is a function of the generated common-mode voltages of the parallel inverters and can be minimized by synchronizing the inverters. The synchronization has previously been achieved by a communication link. However, in photovoltaic systems the inverters may be located far apart from each other. Thus, a control free of communication is desired. It is shown in this doctoral dissertation that the circulating current can also be obtained by a common-mode voltage measurement. A control method based on a short-time switching frequency transition is developed and tested with an actual photovoltaic environment of two parallel inverters connected to two 5 kW solar arrays. Controls based on the measurement of the circulating current and the common-mode voltage are generated and tested. A communication-free method of controlling the circulating current between parallelconnected inverters is developed and verified.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Tropfenbasierte Multiphasen – Mikroreaktionstechnologie in organisch-chemischer Synthese

In der vorliegenden Doktorarbeit werden neue, mikrofluidische Verfahren, zur Durchführung chemischer Reaktionen in mehrphasigen Systemen präsentiert. rnDas Einschließen von Reaktionspartnern in einzelne Segmente, deren Volumina im Bereich von Mikro- bis Femtoliter liegen und die dadurch erzeugten enormen, spezifischen Oberflächen, ermöglichen Massentransportprozesse über die Phasengrenzfläche zwischen einzelnen Segmenten, drastisch zu intensivieren. Aufgrund geringer räumlicher Ausdehnungen einzelner Kompartimente und durch vorherrschende, zirkulierende Strömungen in den einzelnen Abschnitten, sind Diffusions- und Konvektionsprozesse in diesen rasch, sodass an der Grenzfläche gebildete, reaktive Intermediate in sehr kurzen Zeitintervallen umgesetzt werden können. rnrn

Phase diagram of the three-band half-filled Cu-O two-leg ladder

We determine the phase diagram of the half-filled two-leg ladder both at weak and strong coupling, taking into account the Cu d(x)(2)-y(2) and the O p(x) and p(y) orbitals. At weak coupling, renormalization group flows are interpreted with the use of bosonization. Two different models with and without outer oxygen orbitals are examined. For physical parameters, and in the absence of the outer oxygen orbitals, the D-Mott phase arises; a dimerized phase appears when the outer oxygen atoms are included. We show that the circulating current phase that preserves translational symmetry does not appear at weak coupling. In the opposite strong-coupling atomic limit the model is purely electrostatic and the ground states may be found by simple energy minimization. The phase diagram so obtained is compared to the weak-coupling one.

Plasmodium vivax: Induction of CD4(+)CD25(+)FoxP3(+) Regulatory T Cells during Infection Are Directly Associated with Level of Circulating Parasites

Circulation CD4(+)CD25(+)FoxP3(+) regulatory T cells (Tregs) have been associated with the delicate balancing between control of overwhelming acute malaria infection and prevention of immune pathology due to disproportionate inflammatory responses to erythrocytic stage of the parasite. While the role of Tregs has been well-documented in murine models and P. falciparum infection, the phenotype and function of Tregs in P. vivax infection is still poorly characterized. In the current study, we demonstrated that patients with acute P. vivax infection presented a significant augmentation of circulating Tregs producing anti-inflammatory (IL-10 and TGF-beta) as well as pro-inflammatory (IFN-gamma, IL-17) cytokines, which was further positively correlated with parasite burden. Surface expression of GITR molecule and intracellular expression of CTLA-4 were significantly upregulated in Tregs from infected donors, presenting also a positive association between either absolute numbers of CD4(+)CD25(+)FoxP3(+)GITR(+) or CD4(+)CD25(+)FoxP3(+)CTLA-4(+) and parasite load. Finally, we demonstrate a suppressive effect of Treg cells in specific T cell proliferative responses of P. vivax infected subjects after antigen stimulation with Pv-AMA-1. Our findings indicate that malaria vivax infection lead to an increased number of activated Treg cells that are highly associated with parasite load, which probably exert an important contribution to the modulation of immune responses during P. vivax infection.

Oral ingestion of a hydrolyzed gelatin meal in subjects with normal weight and in obese patients: Postprandial effect on circulating gut peptides, glucose and insulin

Gut hormones Ighrelin, peptide YY (PYY) and ghrcagon-like peptide-1 (GLP-1)] are an important group of hormones that target appetite control. They are released from endocrine L cells of the small bowel in proportion to the volume, components and calories in a meal. In the current study, 20 g of gelatin (flavored and sweetened) were given to obese patients (n=12) and lean subjects (n=10). Subsequently, plasma samples were collected at-30-minute intervals rip to 180 minutes and glucose, insulin, PYY, GLP-1 and ghrelin were assayed using specific and sensitive immunofluorometric and radioimmunoassays. As expected, obese patients had normal serum glucose levels, higher serum insulin, and lower plasma concentration of ghrelin at all times compared to lean subjects. GLP-1 plasma levels were significantly elevated at 60 minutes, peaking at 120 minutes in obese patients and lean subjects. As a consequence, there was a significant rise in serum insulin levels with a significantly higher peak level at 60 min (obese) and 30 min (lean). There were no significant changes in PYY plasma concentrations and no correlation was found between body mass index and concentrations of ghrelin, PYY and GLP-1 in the group of obese patients. In conclusion, a single gelatin meal induces a rise in plasma GLP-1 followed by an increase in serum levels of insulin. These findings may be applied to maximize satiety in obese patients as a means of improving adherence to calorie-controlled diets as well as provide better control of diabetic patients.

Increases in circulating matrix metalloproteinase-9 levels following fibrinolysis for acute pulmonary embolism

Introduction: Fibrinolyis is one of the first line therapies in high risk pulmonary embolism (PE) according to current guidelines. Previous studies showed that brinolytic therapy with tPA (tissue plasminogen activator, or alteplase) upregulates the concentrations of matrix metalloproteinases (MMPs) and contributes to hemorrhagic transformation after cardioembolic stroke. However, no previous study has described the circulating MMPs levels following fibrinolysis for acute PE. Materials and Methods: We serially measured the circulating levels of MMPs (MMP-9 and MMP-2) and their endogenous inhibitors, the tissue inhibitor of metalloproteinase (TIMP)-1 and TIMP-2 in alteplase and in streptokinase-treated patients with acute PE by gelatin zymography and by enzyme-linked immunosorbent assays, respectively. Results: We found that therapy of PE streptokinase or with alteplase is associated increased pro-MMP-9, but not MMP-2, concentrations for up to 24 hours, whereas no significant changes were found in TIMP-1 or TIMP-2 concentrations. This alteration returned to normal 3 to 5 days after thrombolysis. This is the first study reporting on MMPs alterations following fibrinolysis for acute PE. Conclusions: We found transient increases in circulating pro-MMP-9 levels following fibrinolysis for acute PE. Our findings support the hypothesis that increased MMP-9 levels may underlie the risk of intracerebral hemorrhage or other bleeding complication of thrombolysis for acute PE, and the use of MMP inhibitors may decrease such risk. (C) 2010 Elsevier Ltd. All rights reserved.

Current status of herpesvirus identification in the oral cavity of HIV-infected children

INTRODUCTION: Some viruses of the Herpesviridae family are frequently the etiologic agents of oral lesions associated with HIV. The aim of this study was to identify the presence of herpes simplex virus types 1 and 2 (HSV-1, HSV-2), Varicella Zoster virus (VZV), Epstein-Barr virus (EBV), human cytomegalovirus (HCMV), human herpesvirus type 6, type 7 and type 8 (HHV-6, HHV-7 and HHV-8) in the oral cavity of HIV-infected children/adolescents and verify the association between viral subtypes and clinical factors. METHODS: The cells of oral mucosa were collected from 50 HIV infected children/adolescents, 3-13 years old (mean age 8.66). The majority (66%) of selected were girls, and they were all outpatients at the pediatric AIDS clinic of a public hospital in Rio de Janeiro. Nested-PCR was used to identify the viral types. RESULTS: Absence of immunosuppression was observed in 66% of the children. Highly active antiretroviral therapy (HAART) was used by 72.1% of selected and moderate viral load was observed in 56% of the children/adolescents. Viral types were found in 86% of the children and the subtypes were: HSV-1 (4%), HSV-2 (2%), VZV (4%), EBV (0%), HCMV (24%), HHV6 (18%), HHV-7 (68%), HHV8 (0%). CONCLUSIONS: The use of HAART has helped to reduce oral lesions, especially with herpes virus infections. The health professionals who work with these patients should be aware of such lesions because of their predictive value and the herpes virus can be found circulating in the oral cavity without causing lesions.

Serial measurement of the circulating levels of tumour necrosis factor and its soluble receptors 1 and 2 for monitoring leprosy patients during multidrug treatment

Leprosy is an infectious and contagious spectral disease accompanied by a series of immunological events triggered by the host response to the aetiologic agent, Mycobacterium leprae . The induction and maintenance of the immune/inflammatory response in leprosy are linked to multiple cell interactions and soluble factors, primarily through the action of cytokines. The purpose of the present study was to evaluate the serum levels of tumour necrosis factor (TNF)-α and its soluble receptors (sTNF-R1 and sTNF-R2) in leprosy patients at different stages of multidrug treatment (MDT) in comparison with non-infected individuals and to determine their role as putative biomarkers of the severity of leprosy or the treatment response. ELISA was used to measure the levels of these molecules in 30 healthy controls and 37 leprosy patients at the time of diagnosis and during and after MDT. Our results showed increases in the serum levels of TNF-α and sTNF-R2 in infected individuals in comparison with controls. The levels of TNF-α, but not sTNF-R2, decreased with treatment. The current results corroborate previous reports of elevated serum levels of TNF-α in leprosy and suggest a role for sTNF-R2 in the control of this cytokine during MDT.

Circulating insulin-like growth factor-I in pregnancy and maternal risk of breast cancer.

BACKGROUND: Elevated serum concentrations of insulin-like growth factor (IGF)-1 have been associated with increased risk of breast cancer. Previously, we reported a similar association in samples obtained during pregnancy. The current study was conducted to further characterize the association of IGF-1 during pregnancy with maternal breast cancer risk. METHODS: A case-control study was nested within the Finnish Maternity Cohort. The study was limited to primiparous women less than 40 years of age, who donated blood samples during early (median, 12 weeks) pregnancy and delivered a single child at term. Seven hundred and nineteen women with invasive breast cancer were eligible. Two controls (n = 1,434) were matched to each case on age and date at blood donation. Serum IGF-1 concentration was measured using an Immulite 2000 analyzer. Conditional logistic regression was used to estimate odds ratios (OR) and 95% confidence intervals (CI).RESULTS: No significant associations were observed between serum IGF-1 concentrations and breast cancer risk in both the overall analysis (OR 1.08 (95% CI 0.80-1.47) and in analyses stratified by histological subtype, lag-time to cancer diagnosis, age at pregnancy or age at diagnosis.CONCLUSIONS: There was no association between IGF-1 and maternal breast cancer risk during early pregnancy in this large nested case-control study.Impact:Serum IGF-1 concentrations during early pregnancy may not be related to maternal risk of breast cancer.

Current concepts in the pathogenesis of urea cycle disorders.

The common feature of urea cycle diseases (UCD) is a defect in ammonium elimination in liver, leading to hyperammonemia. This excess of circulating ammonium eventually reaches the central nervous system, where the main toxic effects of ammonium occur. These are reversible or irreversible, depending on the age of onset as well as the duration and the level of ammonium exposure. The brain is much more susceptible to the deleterious effects of ammonium during development than in adulthood, and surviving UCD patients may develop cortical and basal ganglia hypodensities, cortical atrophy, white matter atrophy or hypomyelination and ventricular dilatation. While for a long time, the mechanisms leading to these irreversible effects of ammonium exposure on the brain remained poorly understood, these last few years have brought new data showing in particular that ammonium exposure alters several amino acid pathways and neurotransmitter systems, cerebral energy, nitric oxide synthesis, axonal and dendritic growth, signal transduction pathways, as well as K(+) and water channels. All these effects of ammonium on CNS may eventually lead to energy deficit, oxidative stress and cell death. Recent work also proposed neuroprotective strategies, such as the use of NMDA receptor antagonists, nitric oxide inhibitors, creatine and acetyl-l-carnitine, to counteract the toxic effects of ammonium. Better understanding the pathophysiology of ammonium toxicity to the brain under UCD will allow the development of new strategies for neuroprotection.

Prospective evaluation of circulating VEGF in patients with advanced non-small cell lung cancer treated with bevacizumab, pemetrexed and cisplatin in the trial SAKK19/09.

Aim: Bevacizumab is a monoclonal antibody directed against the vascular endothelial growth factor (VEGF). The previous phase II trial ABIGAIL (Reck, 2010) suggested circulating VEGF as a prognostic, but not predictive, biomarker for patients (pts) with non-small cell lung cancer (NSCLC) treated with bevacizumab. We prospectively measured VEGF in the multicenter phase II trial SAKK19/09 (NCT01116219). Methods: SAKK19/09 enrolled 77 evaluable patients (pts) with previously untreated, advanced nonsquamous NSCLC and EGFR wild type. Pts received 4 cycles of cisplatin 75mg/m2 (or carboplatin AUC5), pemetrexed 500mg/m2 and bevacizumab 7.5mg/kg, followed by maintenance therapy with pemetrexed and bevacizumab until progression by RECIST1.1. Follow-up CT scans were performed every 6 weeks until week 54 and every 12 weeks thereafter. Baseline EDTA blood samples were sent by same-day courier to the central laboratory for centrifugation, aliquoting, and freezing. Upon completion of enrollment, aliquots were thawed, and VEGF quantification was performed centrally using Luminex® Performance Assay Human Base Kit A (R&D Systems, Abingdon, UK). The mean value was used to stratify pts into two groups (low versus high VEGF). Best response rate assessed by RECIST1.1 (CR + PR versus SD + PD). Results: Clinical results of the SAKK19/09 trial were reported previously (Gautschi, 2013). Baseline plasma VEGF was detectable in 71 of 77 (92%) evaluable patients treated with chemotherapy and bevacizumab. The mean value was 74.9 pg/ml, the median 47.5 pg/ml, and the range 3.55 to 310 pg/ml. Using the mean as a predefined cutoff value, 50 patients had low VEGF levels and 21 patients had high VEGF levels. High VEGF was significantly associated with shorter PFS (4.1 vs 8.3 months, HR = 2.56; 95%CI: 1.43- 4.57; p = 0.0015) and OS (8.7 vs 17.5 months, HR = 2.67; 95% CI: 1.37-5.20; p = 0.0041), but not with best response rate ( p = 0.2256). Conclusions: Consistent with the ABIGAIL trial, circulating VEGF was prognostic, but not predictive for response, in the current trial. Further work is ongoing to identify potentially predictive biomarkers for bevacizumab, using comprehensive proteomic analyses. Disclosure: S.I. Rothschild: I received honoraria for the participation in advisory boards from Eli Lilly and Roche and for presentations at scientific symposiums sponsored by Roche; O. Gautschi: Honoraria for advisory boards of Eli Lilly and Roche; R. Cathomas: Advisory board member: Eli Lilly. All other authors have declared no conflicts of interest.

Current status of the waste-to-energy chain in the County of North Savo, Finland

The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.

Electro-Oxidation Treatment of Pulp and Paper Mill Circulating Waters and Wastewaters

Interest in water treatment by electrochemical methods has grown in recent years. Electrochemical oxidation has been applied particularly successfully to degrade different organic pollutants and disinfect drinking water. This study summarizes the effectiveness of the electrochemical oxidation technique in inactivating different primary biofilm forming paper mill bacteria as well as sulphide and organic material in pulp and paper mill wastewater in laboratory scale batch experiments. Three different electrodes, borondoped diamond (BDD), mixed metal oxide (MMO) and PbO2, were employed as anodes. The impact on inactivation efficiency of parameters such as current density and initial pH or chloride concentration of synthetic paper machine water was studied. The electrochemical behaviour of the electrodes was investigated by cyclic voltammetry with MMO, BDD and PbO2 electrodes in synthetic paper mill water as also with MMO and stainless steel electrodes with biocides. Some suggestions on the formation of different oxidants and oxidation mechanisms were also presented during the treatment. Aerobic paper mill bacteria species (Deinococcus geothermalis, Pseudoxanthomonas taiwanensis and Meiothermus silvanus) were inactivated effectively (>2 log) at MMO electrodes by current density of 50 mA/cm2 and the time taken three minutes. Increasing current density and initial chloride concentration of paper mill water increased the inactivation rate of Deinococcus geothermalis. The inactivation order of different bacteria species was Meiothermus silvanus > Pseudoxanthomonas taiwanensis > Deinococcus geothermalis. It was observed that inactivation was mainly due to the electrochemically generated chlorine/hypochlorite from chloride present in the water and also residual disinfection by chlorine/hypochlorite occurred. In real paper mill effluent treatment sulphide oxidation was effective with all the different initial concentrations (almost 100% reduction, current density 42.9 mA/cm2) and also anaerobic bacteria inactivation was observed (almost 90% reduction by chloride concentration of 164 mg/L and current density of 42.9 mA/cm2 in five minutes). Organic material removal was not as effective when comparing with other tested techniques, probably due to the relatively low treatment times. Cyclic voltammograms in synthetic paper mill water with stainless steel electrode showed that H2O2 could be degraded to radicals during the cathodic runs. This emphasises strong potential of combined electrochemical treatment with this biocide in bacteria inactivation in paper mill environments.