Chipping Away at the Monolith: Dispelling the Myth of Father Noninvolvement in Children's Early Literacy Development

Current research stresses the importance of parent involvement in their children 's academic development. Parents reading and writing with their young children is shown to prepare them for the benefits of for ma I education. Studies completed on parent participation in early literacy activities have tended to look at mothers ' role. Few researchers have investigated the contributions fathers have made. The results of a study completed on father-child early literacy practices are presented. Fathers reported engaging in reading and writing activities with their children for three reasons: To prepare their children for school, to bond with their children, and to assist their children in language skill development. Recommendations are provided on how to encourage fathers to participate in early literacy practices

Reliability and Failure Modes of Implant-Supported Y-TZP and MCR Three-Unit Bridges

Purpose: Chipping within veneering porcelain has resulted in high clinical failure rates for implant-supported zirconia (yttria-tetragonal zirconia polycrystals [Y-TZP]) bridges. This study evaluated the reliability and failure modes of mouth-motion step-stress fatigued implant-supported Y-TZP versus palladium-silver alloy (PdAg) three-unit bridges. Materials and Methods: Implant-abutment replicas were embedded in polymethylmethacrylate resin. Y-TZP and PdAg frameworks, of similar design (n = 21 each), were fabricated, veneered, cemented (n = 3 each), and Hertzian contact-tested to obtain ultimate failure load. In each framework group, 18 specimens were distributed across three step-stress profiles and mouth-motion cyclically loaded according to the profile on the lingual slope of the buccal cusp of the pontic. Results: PdAg failures included competing flexural cracking at abutment and/or connector area and chipping, whereas Y-TZP presented predominantly cohesive failure within veneering porcelain. Including all failure modes, the reliability (two-sided at 90% confidence intervals) for a ""mission"" of 50,000 and 100,000 cycles at 300 N load was determined (Alta Pro, Reliasoft, Tucson, AZ, USA). No difference in reliability was observed between groups for a mission of 50,000. Reliability remained unchanged for a mission of 100,000 for PdAg, but significantly decreased for Y-TZP. Conclusions: Higher reliability was found for PdAg for a mission of 100,000 cycles at 300 N. Failure modes differed between materials.

Fatigue life and failure modes of crowns systems with a modified framework design

Objectives: To evaluate the effect of framework design on the fatigue life and failure modes of metal ceramic (MC, Ni-Cr alloy core, VMK 95 porcelain veneer), glass-infiltrated alumina (ICA, In-Ceram Alumina/VM7), and veneered yttria-stabilized tetragonal zirconia polycrystals (Y-TZP, IPSe.max ZirCAD/IPS e.max,) crowns. Methods: Sixty composite resin tooth replicas of a prepared maxillary first molar were produced to receive crowns systems of a standard (MCs, ICAs, and Y-TZPs, n = 10 each) or a modified framework design (MCm, ICAm, and Y-TZPm, n = 10 each). Fatigue loading was delivered with a spherical steel indenter (3.18 mm radius) on the center of the occlusal surface using r-ratio fatigue (30-300 N) until completion of 10(6) cycles or failure. Fatigue was interrupted every 125,000 cycles for damage evaluation. Weibull distribution fits and contour plots were used for examining differences between groups. Failure mode was evaluated by light polarized and SEM microscopy. Results: Weibull analysis showed the highest fatigue life for MC crowns regardless of framework design. No significant difference (confidence bound overlaps) was observed between ICA and Y-TZP with or without framework design modification. Y-TZPm crowns presented fatigue life in the range of MC crowns. No porcelain veneer fracture was observed in the MC groups, whereas ICAs presented bulk fracture and ICAm failed mainly through the veneer. Y-TZP crowns failed through chipping within the veneer, without core fractures. Conclusions: Framework design modification did not improve the fatigue life of the crown systems investigated. Y-TZPm crowns showed comparable fatigue life to MC groups. Failure mode varied according to crown system. (C) 2010 Elsevier Ltd. All rights reserved.

Monolithic CAD/CAM Lithium Disilicate Versus Veneered Y-TZP Crowns: Comparison of Failure Modes and Reliability After Fatigue

Purpose: The aim of this research was to evaluate the fatigue behavior and reliability of monolithic computer-aided design/computer-assisted manufacture (CAD/CAM) lithium disilicate and hand-layer-veneered zirconia all-ceramic crowns. Materials and Methods: A CAD-based mandibular molar crown preparation, fabricated using rapid prototyping, served as the master die. Fully anatomically shaped monolithic lithium disilicate crowns (IPS e.max CAD, n = 19) and hand-layer-veneered zirconia-based crowns (IPS e.max ZirCAD/Ceram, n = 21) were designed and milled using a CAD/CAM system. Crowns were cemented on aged dentinlike composite dies with resin cement. Crowns were exposed to mouth-motion fatigue by sliding a WC-indenter (r = 3.18 mm) 0.7 mm lingually down the distobuccal cusp using three different step-stress profiles until failure occurred. Failure was designated as a large chip or fracture through the crown. If no failures occurred at high loads (> 900 N), the test method was changed to staircase r ratio fatigue. Stress level probability curves and reliability were calculated. Results: Hand-layer-veneered zirconia crowns revealed veneer chipping and had a reliability of < 0.01 (0.03 to 0.00, two-sided 90% confidence bounds) for a mission of 100,000 cycles and a 200-N load. None of the fully anatomically shaped CAD/CAM-fabricated monolithic lithium disilicate crowns failed during step-stress mouth-motion fatigue (180,000 cycles, 900 N). CAD/CAM lithium disilicate crowns also survived r ratio fatigue (1,000,000 cycles, 100 to 1,000 N). There appears to be a threshold for damage/bulk fracture for the lithium disilicate ceramic in the range of 1,100 to 1,200 N. Conclusion: Based on present fatigue findings, the application of CAD/CAM lithium disilicate ceramic in a monolithic/fully anatomical configuration resulted in fatigue-resistant crowns, whereas hand-layer-veneered zirconia crowns revealed a high susceptibility to mouth-motion cyclic loading with early veneer failures. Int J Prosthodont 2010; 23: 434-442.

Reliability of Metalloceramic and Zirconia-based Ceramic Crowns

Despite the increasing utilization of all-ceramic crown systems, their mechanical performance relative to that of metal ceramic restorations (MCR) has yet to be determined. This investigation tested the hypothesis that MCR present higher reliability over two Y-TZP all-ceramic crown systems under mouth-motion fatigue conditions. A CAD-based tooth preparation with the average dimensions of a mandibular first molar was used as a master die to fabricate all restorations. One 0.5-mm Pd-Ag and two Y-TZP system cores were veneered with 1.5 mm porcelain. Crowns were cemented onto aged (60 days in water) composite (Z100, 3M/ESPE) reproductions of the die. Mouth-motion fatigue was performed, and use level probability Weibull curves were determined. Failure modes of all systems included chipping or fracture of the porcelain veneer initiating at the indentation site. Fatigue was an acceleration factor for all-ceramic systems, but not for the MCR system. The latter presented significantly higher reliability under mouth-motion cyclic mechanical testing.

Development of a Model for the Ice Scraping Process, October 1996

A laboratory study has been conducted with two aims in mind. The first goal was to develop a description of how a cutting edge scrapes ice from the road surface. The second goal was to investigate the extent, if any, to which serrated blades were better than un-serrated or "classical" blades at ice removal. The tests were conducted in the Ice Research Laboratory at the Iowa Institute of Hydraulic Research of the University of Iowa. A specialized testing machine, with a hydraulic ram capable of attaining scraping velocities of up to 30 m.p.h. was used in the testing. In order to determine the ice scraping process, the effects of scraping velocity, ice thickness, and blade geometry on the ice scraping forces were determined. Higher ice thickness lead to greater ice chipping (as opposed to pulverization at lower thicknesses) and thus lower loads. Behavior was observed at higher velocities. The study of blade geometry included the effect of rake angle, clearance angle, and flat width. The latter were found to be particularly important in developing a clear picture of the scraping process. As clearance angle decreases and flat width increases, the scraping loads show a marked increase, due to the need to re-compress pulverized ice fragments. The effect of serrations was to decrease the scraping forces. However, for the coarsest serrated blades (with the widest teeth and gaps) the quantity of ice removed was significantly less than for a classical blade. Finer serrations appear to be able to match the ice removal of classical blades at lower scraping loads. Thus, one of the recommendations of this study is to examine the use of serrated blades in the field. Preliminary work (by Nixon and Potter, 1996) suggests such work will be fruitful. A second and perhaps more challenging result of the study is that chipping of ice is more preferable to pulverization of the ice. How such chipping can be forced to occur is at present an open question.

Development of a Model for the Ice Scraping Process Iowa Department of Transportation Project HR 361 Final Report, October 1996

A laboratory study has been conducted with two aims in mind. The first goal was to develop a description of how a cutting edge scrapes ice from the road surface. The second goal was to investigate the extent, if any, to which serrated blades were better than un-serrated or "classical" blades at ice removal. The tests were conducted in the Ice Research Laboratory at the Iowa Institute of Hydraulic Research of the University of Iowa. A specialized testing machine, with a hydraulic ram capable of attaining scraping velocities of up to 30 m.p.h. was used in the testing. In order to determine the ice scraping process, the effects of scraping velocity, ice thickness, and blade geometry on the ice scraping forces were determined. Higher ice thickness lead to greater ice chipping (as opposed to pulverization at lower thicknesses) and thus lower loads. S~milabr ehavior was observed at higher velocities. The study of blade geometry included the effect of rake angle, clearance angle, and flat width. The latter were found to be particularly important in developing a clear picture of the scraping process. As clearance angle decreases and flat width increases, the scraping loads show a marked increase, due to the need to re-compress pulverized ice fragments. The effect of serrations was to decrease the scraping forces. However, for the coarsest serrated blades (with the widest teeth and gaps) the quantity of ice removed was significantly less than for a classical blade. Finer serrations appear to be able to match the ice removal of classical blades at lower scraping loads. Thus, one of the recommendations of this study is to examine the use of serrated blades in the field. Preliminary work (by Nixon and Potter, 1996) suggests such work will be fruitful. A second and perhaps more challenging result of the study is that chipping of ice is more preferable to pulverization of the ice. How such chipping can be forced to occur is at present an open question.

A 3 years retrospective study of survival for zirconia-based single crowns fabricated from intraoral digital impressions.

OBJECTIVE: To evaluate the clinical performance of glass-ceramic/zirconia crowns fabricated using intraoral digital impressions - a retrospective study with a three-year follow-up. METHODS: 70 consecutive patients with a total of 86 glass-ceramic/zirconia crowns were treated by a single clinician using standardized clinical and laboratory protocols. A complete digital workflow was adopted for the purpose except for the veneering procedure for the glass-ceramic crowns. Occlusal adjustments were made before the ceramic glazing procedure. Before cementation, all abutments where carefully cleaned with a 70% alcoholic solution and air dried. Cementation was performed using dual-curing, self-adhesive resin cement. Patients were re-examined after 12, 24 and 36 months, to assess crown chipping/fractures. RESULTS: After the three-year follow-up, none of the zirconia-based restoration was lost ("apparent" survival rate 100%) otherwise, the chipping rate of the veneering material increased from 9.3% after 12 months, to 14% after 24 months to 30.2% after 36 months. As a consequence, the "real" success rate after 3 years was 69.8%. CONCLUSIONS: After 3 years the success rate of zirconia-based crowns was 69.8%, while the incidence of the chipping was 30.2%. Assuming an exponential increase in chipping rate between 12 and 36 months it can be argued that, among others, the fatigue-mechanism could be advocated as the main factor for the failure of glass-ceramic veneered zirconia especially after 24 months.

Survival of zirconia- and metal-supported fixed dental prostheses: a systematic review

Purpose: The aim of this review was to systematically evaluate and compare the frequency of veneer chipping and core fracture of zirconia fixed dental prostheses (FOPS) and porcelain-fused-to-metal (PFM) FDPs and determine possible influencing factors. Materials and Methods: The SCOPUS database and International Association of Dental Research abstracts were searched for clinical studies involving zirconia and PFM FDPs. Furthermore, studies that were integrated into systematic reviews on PFM FDPs were also evaluated. The principle investigators of any clinical studies on zirconia FDPs were contacted to provide additional information. Based on the available information for each FOP, a data file was constructed. Veneer chipping was divided into three grades (grade 1 = polishing, grade 2 = repair, grade 3 = replacement). To assess the frequency of veneer chipping and possible influencing factors, a piecewise exponential model was used to adjust for a study effect. Results: None of the studies on PFM FDPs (reviews and additional searching) sufficiently satisfied the criteria of this review to be included. Thirteen clinical studies on zirconia FDPs and two studies that investigated both zirconia and PFM FDPs were identified. These studies involved 664 zirconia and 134 PFM FDPs at baseline. Follow-up data were available for 595 zirconia and 127 PFM FDPs. The mean observation period was approximately 3 years for both groups. The frequency of core fracture was less than 1% in the zirconia group and 0% in the PFM group. When all studies were included, 142 veneer chippings were recorded for zirconia FDPs (24%) and 43 for PFM FDPs (34%). However, the studies differed extensively with regard to veneer chipping of zirconia: 85% of all chippings occurred in 4 studies, and 43% of all chippings included zirconia FDPs. If only studies that evaluated both types of core materials were included, the frequency of chipping was 54% for the zirconia-supported FDPs and 34% for PFM FDPs. When adjusting the survival rate for the study effect, the difference between zirconia and PFM FDPs was statistically significant for all grades of chippings (P = .001), as well as for chipping grade 3 (P = .02). If all grades of veneer chippings were taken into account, the survival of PFM FDPs was 97%, while the survival rate of the zirconia FDPs was 90% after 3 years for a typical study. For both PFM and zirconia FDPs, the frequency of grades 1 and 2 veneer chippings was considerably higher than grade 3. Veneer chipping was significantly less frequent in pressed materials than in hand-layered materials, both for zirconia and PFM FDPs (P = .04). Conclusions: Since the frequency of veneer chipping was significantly higher in the zirconia FDPs than PFM FDPs, and as refined processing procedures have started to yield better results in the laboratory, new clinical studies with these new procedures must confirm whether the frequency of veneer chipping can be reduced to the level of PFM. Int J Prosthodont 2010;23:493-502

IRTOPALATERÄN KEHITTÄMINEN SÄRMÄ- JA PROFILOINTIHAKETUKSEEN

Diplomityön tarkoituksena on kehittää irtopalaterä sahahakkeen valmistukseen. Tutkimuksessa perehdytään lastun irtoamisen perusteisiin ja lastun kulkeutumiseen ulos terältä. Tutkimuksessa keskeisenä osana ovat laboratoriokokeet joissa suurnopeuskameralla kuvaamalla selvitetään lastun kulkeutuminen. Saatujen tulosten perusteella muodostetaan terän toimivuuden kannalta keskeiset suunnitteluperusteet. Tutkimuksen kirjallisessa osuudessa selvitetään lastun muodostuminen ja siihen vaikuttavat tekijät.

Eräällä pelkkahakkurilla tuotetun selluhakkeen laatujakauman hallinta

Tämän diplomityön tarkoituksena on selvittää eräällä pelkkahakkurilla tuotetun selluhakkeen laadun vaihtelua ja laadun hallinnan mahdollisuuksia. Tutkittu laite on Veisto Oy:n suunnittelema ja valmistama HewSaw R200 - pelkkahakkuri. Tutkimuksessa selvitetään sahauksen yhteydessä pelkkahakkurilla tuotettavaan selluhakkeeseen vaikuttavien parametrien: hakkurin pyörimisnopeuden, tukin syöttönopeuden, hakkurin terien vaihtovälin, selluhakkeen palakoon, tukkiluokan, puun lämpötilan ja puulajin välisiä korrelaatioita ja edellä mainittujen tekijöiden vaikutusta tuotettavan hakkeen palakokojakaumaan. Tämä palakokojakauma määrää selluhakkeen laadunmäärityksessä käytettävän, niin sanotun hintakertoimen. Kyseinen hintakerroin määritellään SCAN – CM 40 – standardin mukaisella seulonnalla. Tämä standardi on käytössä laadunmäärityksen perusteena kaikilla pohjoismaisilla sellutehtailla.Tutkimuksen kirjallisessa osuudessa esitellään sahateollisuuden merkittävimmät sahausmenetelmät ja sivuotteiden tuotanto . Seuraavassa osassa käsitellään erikseen selluhaketta sahateollisuuden sivutuotteena ja sen taloudellista merkitystä sahateollisuudessa. Jatkossa keskitytään selluhakkeen tuottamiseen pelkkahakkurilla ja puun työstämiseen liittyviin periaatteisiin.Tutkimuksen kokeellisessa osuudessa tutkittaan, eri sahalaitoksilta otettujen hakenäytteiden perusteella, tärkeimmiksi havaittujen tuotantoparametrien vaikutusta selluhakkeen laatuun ja saantoon. Näytteitä otettiin tutkimuksen kokeellisessa osuudessa yhteensä noin 250 kappaletta. Tutkimuksen tuloksia käsittelevässä osuudessa on annettu malli tutkitulla HewSaw R200 - pelkkahakkurilla tuotetun selluhakkeen laadun ja määrän arvioimiseen.

Cost-Efficiency of Birch Sprinkling in Kraft Pulping

Työn tavoitteena oli selvittää koivun kasteluvarastoinnin kannattavuus selluteollisuudessa. Lisäksi tutkittiin, kuinka kastelu vaikuttaa puuaineeseen varastoinnin aikana ja kuinka koivun kasteluvarastointi vaikuttaa puun kuorintaan ja haketukseen, keitettävyyteen, vaalenevuuteen sekä sellun laatuun. Enocellin puukentälle rakennettiin kasteluvarasto, jossa varastoitiin 40,000 m3sob koivua. Kastelu oli päällä huhtikuusta lokakuuhun asti. Kastelun vaikutusta puuaineen muutoksiin arvioitiin lahotutkimusten avulla. Tehdaskoeajoissa verrattiin tuoretta, kasteluvarastoitua ja kuivavarastoitua koivua. Puuaines säilyi lähes muuttumattomana yhden kesän kasteluvarastoinnissa. Kastellulla koivulla terveen puun osuus oli yli 85 % kesän lopussa, kun se oli alle 20 % kuivavarastoidulla koivulla. Kuorinnan puuhäviö laskee selvästi kastelukoivulla ja myös hakkeen laatu oli parempaa kuin kuivavarastoidulla koivulla. Kastelukoivulla hakkeen kuoripitoisuus oli vain 0.13 %. Kuoren kuiva-aine oli 12 prosenttiyksikköä alhaisempi kuin kuivalla koivulla, mutta kuoren lämpöarvossa ero oli vain 1 €/ADt. Varastointimenetelmällä ei ollut vaikutusta hakkeen keitettävyyteen, mutta tuoreella puulla keitettävyys oli parempi kuin varastoidulla puulla. Sellun asetoniuutepitoisuus oli samalla tasolla tuoreella ja kastellulla puulla. Kuivalla syyspuulla uutetaso oli korkeampi, vaikka hartsisaippuan annostusta nostettiin 10 kg/ADt. Betulinolitaso oli kastellulla puulla erittäin alhainen puun hyvän kuoriutuvuuden vuoksi. Kastellun ja tuoreen puun vaalenevuus oli parempi kuin kuivalla puulla. Aktiivikloorin kulutus oli 3 – 4 kg/ADt alhaisempi kuin kuivalla syyspuulla. Puun varastoinnilla ei ollut vaikutusta sellun laatuun. Koivun kasteluvarastoinnin kannattavuus on erittäin hyvä. Tuotantokustannukset määritettiin tuoreelle, kastellulle, kierrätetylle sekä kuivalle koivulle. Kasteluvarastointi laskee tuotantokustannuksia noin 10 €/ADt verrattuna kierrätettyyn koivuun. Kuivavarastoidun puun käyttö nostaa tuotantokustannuksia noin 5 €/ADt verrattuna kastelukoivuun. Kierrätetyn ja kuivavarastoidun puun kustannusero johtuu kierrätyskustannuksista. Kasteluvarastolle, jota käytettiin kesällä 2004, takaisinmaksuaika on vain 0.4 vuotta. Jos tavoiteltu takaisinmaksuaika olisi kaksi vuotta, niin perusinvestointi 80,000 m3sob varastolle voisi maksaa noin 370 k€.