Dissipation of DDT in a heavily contaminated soil in Mato Grosso, Brazil

After the prohibition of organochlorine-pesticide use in Brazil for controlling insect vector diseases, Mato Grosso State gathered the exceeding DDT and stored it irregularly in an open air area that belongs to the National Health Foundation, causing soil contamination. This study aimed to evaluate the contamination level and dissipation of p,p′-DDT and p,p′-DDE in this area. For that, surface soil samples were collected on 19 September 2000, 15 December 2000, 4 April 2001 and soil samples 30-40 cm; 60-70 cm and 90-100 cm deep were taken from five points in the studied area on 17 July 2001. The contaminants were determined by a small scale method which consists on extraction and clean-up steps combined into one step by transferring soil samples mixed with neutral alumina to a chromatographic column prepacked with neutral alumina and elution with hexane:dichloromethane (7:3 v:v). The eluate was concentrated and the analytes were quantified by gas chromatography with an electron-capture detector. p,p′-DDT at surface soil ranged from 3800 to 7300 mg kg -1. 30-40 cm deep soil sample concentrations varied from 0.036 to 440 mg kg -1 while 90-100 cm deep samples varied from 0.069 to 180 mg kg -1. Volatilization is probably the main dissipation process. The p,p′-DDT is moving slowly downward in the soil profile, however, the levels of this contaminant are high enough to present risk to underground waters. © 2005 Elsevier Ltd. All rights reserved.

Electrochemical oxidation of wastewater containing aromatic amines using a flow electrolytic reactor

Aromatic amines are environmental pollutants and represent one of the most important classes of industrial and natural chemicals. Some types of complex effluents containing these chemical species, mainly those originated from chemicals plants are not fully efficiently treated by conventional processes. In this work, the use of electrochemical technology through an electrolytic pilot scale flow reactor is considered for treatment of wastewater of a chemical industry manufacturer of antioxidant and anti-ozonant substances used in rubber. Experimental results showed that was possible to remove between 65% and 95% of apparent colour and chemical oxygen demand removal between 30 and 90% in 60 min of treatment, with energy consumption rate from 26 kWh m-3 to 31 kWh m-3. Absorbance, total organic carbon and toxicity analyses resulted in no formation of toxic by-products. The results suggest that the presented electrochemical process is a suitable method for treating this type of wastewater, mainly when pre-treated by aeration. Copyright © 2013 Inderscience Enterprises Ltd.

Interactions métaboliques entre le bisphénol A et le naproxène dans un modèle de foie de rat isolé et perfusé

L'exposition aux mélanges de contaminants (environnementaux, alimentaires ou thérapeutiques) soulève de nombreuses interrogations et inquiétudes vis-à-vis des probabilités d'interactions toxicocinétiques et toxicodynamiques. Une telle coexposition peut influencer le mode d’action des composants du cocktail et donc de leur toxicité, suite à un accroissement de leurs concentrations internes. Le bisphénol A (4 dihydroxy-2,2-diphenylpropane) est un contaminant chimique répandu de manière ubiquitaire dans notre environnement, largement utilisé dans la fabrication des plastiques avec l’un des plus grands volumes de production à l’échelle mondiale. Il est un perturbateur endocrinien par excellence de type œstrogèno-mimétique. Cette molécule est biotransformée en métabolites non toxiques par un processus de glucuronidation. L'exposition concomitante à plusieurs xénobiotiques peut induire à la baisse le taux de glucuronidation du polluant chimique d'intérêt, entre autres la co-exposition avec des médicaments. Puisque la consommation de produits thérapeutiques est un phénomène grandissant dans la population, la possibilité d’une exposition simultanée est d’autant plus grande et forte. Sachant que l'inhibition métabolique est le mécanisme d'interaction le plus plausible pouvant aboutir à une hausse des niveaux internes ainsi qu’à une modulation de la toxicité prévue, la présente étude visait d'abord à confirmer et caractériser ce type d'interactions métaboliques entre le bisphénol A et le naproxène, qui est un anti-inflammatoire non stéroïdiennes (AINS), sur l'ensemble d'un organe intact en utilisant le système de foie de rat isolé et perfusé (IPRL). Elle visait ensuite à déterminer la cinétique enzymatique de chacune de ces deux substances, seule puis en mélange binaire. Dans un second temps, nous avons évalué aussi l’influence de la présence d'albumine sur la cinétique métabolique et le comportement de ces deux substances étudiées en suivant le même modèle de perfusion in vivo au niveau du foie de rat. Les constantes métaboliques ont été déterminées par régression non linéaire. Les métabolismes du BPA et du NAP seuls ont montré une cinétique saturable avec une vélocité maximale (Vmax) de 8.9 nmol/min/ mg prot de foie et une constante d'affinité de l'enzyme pour le substrat (Km) de 51.6 μM pour le BPA et de 3 nmol/min/mg prot de foie et 149.2 μM pour le NAP. L'analyse des expositions combinées suggère une inhibition compétitive partielle du métabolisme du BPA par le NAP avec une valeur de Ki estimée à 0.3542 μM. Les résultats obtenus montrent que l’analyse de risque pour les polluants environnementaux doit donc prendre en considération la consommation des produits pharmaceutiques comme facteur pouvant accroitre le niveau interne lors d’une exposition donnée. Ces données in vivo sur les interactions métaboliques pourraient être intégrées dans un modèle pharmacocinétique à base physiologique (PBPK) pour prédire les conséquences toxicococinétique (TK) de l'exposition d'un individu à ces mélanges chimiques.

Interactions métaboliques entre le bisphénol A et le naproxène dans un modèle de foie de rat isolé et perfusé

L'exposition aux mélanges de contaminants (environnementaux, alimentaires ou thérapeutiques) soulève de nombreuses interrogations et inquiétudes vis-à-vis des probabilités d'interactions toxicocinétiques et toxicodynamiques. Une telle coexposition peut influencer le mode d’action des composants du cocktail et donc de leur toxicité, suite à un accroissement de leurs concentrations internes. Le bisphénol A (4 dihydroxy-2,2-diphenylpropane) est un contaminant chimique répandu de manière ubiquitaire dans notre environnement, largement utilisé dans la fabrication des plastiques avec l’un des plus grands volumes de production à l’échelle mondiale. Il est un perturbateur endocrinien par excellence de type œstrogèno-mimétique. Cette molécule est biotransformée en métabolites non toxiques par un processus de glucuronidation. L'exposition concomitante à plusieurs xénobiotiques peut induire à la baisse le taux de glucuronidation du polluant chimique d'intérêt, entre autres la co-exposition avec des médicaments. Puisque la consommation de produits thérapeutiques est un phénomène grandissant dans la population, la possibilité d’une exposition simultanée est d’autant plus grande et forte. Sachant que l'inhibition métabolique est le mécanisme d'interaction le plus plausible pouvant aboutir à une hausse des niveaux internes ainsi qu’à une modulation de la toxicité prévue, la présente étude visait d'abord à confirmer et caractériser ce type d'interactions métaboliques entre le bisphénol A et le naproxène, qui est un anti-inflammatoire non stéroïdiennes (AINS), sur l'ensemble d'un organe intact en utilisant le système de foie de rat isolé et perfusé (IPRL). Elle visait ensuite à déterminer la cinétique enzymatique de chacune de ces deux substances, seule puis en mélange binaire. Dans un second temps, nous avons évalué aussi l’influence de la présence d'albumine sur la cinétique métabolique et le comportement de ces deux substances étudiées en suivant le même modèle de perfusion in vivo au niveau du foie de rat. Les constantes métaboliques ont été déterminées par régression non linéaire. Les métabolismes du BPA et du NAP seuls ont montré une cinétique saturable avec une vélocité maximale (Vmax) de 8.9 nmol/min/ mg prot de foie et une constante d'affinité de l'enzyme pour le substrat (Km) de 51.6 μM pour le BPA et de 3 nmol/min/mg prot de foie et 149.2 μM pour le NAP. L'analyse des expositions combinées suggère une inhibition compétitive partielle du métabolisme du BPA par le NAP avec une valeur de Ki estimée à 0.3542 μM. Les résultats obtenus montrent que l’analyse de risque pour les polluants environnementaux doit donc prendre en considération la consommation des produits pharmaceutiques comme facteur pouvant accroitre le niveau interne lors d’une exposition donnée. Ces données in vivo sur les interactions métaboliques pourraient être intégrées dans un modèle pharmacocinétique à base physiologique (PBPK) pour prédire les conséquences toxicococinétique (TK) de l'exposition d'un individu à ces mélanges chimiques.

Pollutant characteristics on roof surfaces for evaluation as a stormwater harvesting catchment

This paper presents the outcomes of a study which focused on evaluating roof surfaces as stormwater harvesting catchments. Build-up and wash-off samples were collected from model roof surfaces. The collected build-up samples were separated into five different particle size ranges prior to the analysis of physico-chemical parameters. Study outcomes showed that roof surfaces are efficient catchment surfaces for the deposition of fine particles which travel over long distances. Roof surfaces contribute relatively high pollutant loads to the runoff and hence significantly influence the quality of the harvested rainwater. Pollutants associated with solids build-up on roof surfaces can vary with time, even with minimal changes to total solids load and particle size distribution. It is postulated that this variability is due to changes in distant atmospheric pollutant sources and wind patterns. The study highlighted the requirement for first flush devices to divert the highly polluted initial portion of roof runoff. Furthermore, it is highly recommended to not to harvest runoff from small intensity rainfall events since there is a high possibility that the runoff would contain a significant amount of pollutants even after the initial runoff fraction.

Influence of physical and chemical properties of solids on heavy metal adsorption

Partition of heavy metals between particulate and dissolve fraction of stormwater primarily depends on the adsorption characteristics of solids particles. Moreover, the bioavailability of heavy metals is also influenced by the adsorption behaviour of solids. However, due to the lack of fundamental knowledge in relation to the heavy metals adsorption processes of road deposited solids, the effectiveness of stormwater management strategies can be limited. The research study focused on the investigation of the physical and chemical parameters of solids on urban road surfaces and, more specifically, on heavy metal adsorption to solids. Due to the complex nature of heavy metal interaction with solids, a substantial database was generated through a series of field investigations and laboratory experiments. The study sites for the build-up pollutant sample collection were selected from four urbanised suburbs located in a major river catchment. Sixteen road sites were selected from these suburbs and represented typical industrial, commercial and residential land uses. Build-up pollutants were collected using a wet and dry vacuum collection technique which was specially designed to improve fine particle collection. Roadside soil samples were also collected from each suburb for comparison with the road surface solids. The collected build-up solids samples were separated into four particle size ranges and tested for a range of physical and chemical parameters. The solids build-up on road surfaces contained a high fraction (70%) of particles smaller than 150ìm, which are favourable for heavy metal adsorption. These solids particles predominantly consist of soil derived minerals which included quartz, albite, microcline, muscovite and chlorite. Additionally, a high percentage of amorphous content was also identified in road deposited solids. In comparing the mineralogical data of surrounding soil and road deposited solids, it was found that about 30% of the solids consisted of particles generated from traffic related activities on road surfaces. Significant difference in mineralogical composition was noted in different particle sizes of build-up solids. Fine solids particles (<150ìm) consisted of a clayey matrix and high amorphous content (in the region of 40%) while coarse particles (>150ìm) consisted of a sandy matrix at all study sites, with about 60% quartz content. Due to these differences in mineralogical components, particles larger than and smaller than 150ìm had significant differences in their specific surface area (SSA) and effective cation exchange capacity (ECEC). These parameters, in turn, exert a significant influence on heavy metal adsorption. Consequently, heavy metal content in >150ìm particles was lower than in the case of fine particles. The particle size range <75ìm had the highest heavy metal content, corresponding with its high clay forming minerals, high organic matter and low quartz content which increased the SSA, ECEC and the presence of Fe, Al and Mn oxides. The clay forming minerals, high organic matter and Fe, Al and Mn oxides create distinct groups of charge sites on solids surfaces and exhibit different adsorption mechanisms and bond strength, between heavy metal elements and charge sites. Therefore, the predominance of these factors in different particle sizes leads to different heavy metal adsorption characteristics. Heavy metals show preference for association with clay forming minerals in fine solids particles, whilst in coarse particles heavy metals preferentially associate with organic matter. Although heavy metal adsorption to amorphous material is very low, the heavy metals embedded in traffic related materials have a potential impact on stormwater quality.Adsorption of heavy metals is not confined to an individual type of charge site in solids, whereas specific heavy metal elements show preference for adsorption to several different types of charge sites in solids. This is attributed to the dearth of preferred binding sites and the inability to reach the preferred binding sites due to competition between different heavy metal species. This confirms that heavy metal adsorption is significantly influenced by the physical and chemical parameters of solids that lead to a heterogeneity of surface charge sites. The research study highlighted the importance of removal of solids particles from stormwater runoff before they enter into receiving waters to reduce the potential risk posed by the bioavailability of heavy metals. The bioavailability of heavy metals not only results from the easily mobile fraction bound to the solids particles, but can also occur as a result of the dissolution of other forms of bonds by chemical changes in stormwater or microbial activity. Due to the diversity in the composition of the different particle sizes of solids and the characteristics and amount of charge sites on the particle surfaces, investigations using bulk solids are not adequate to gain an understanding of the heavy metal adsorption processes of solids particles. Therefore, the investigation of different particle size ranges is recommended for enhancing stormwater quality management practices.

Pollutant concentrations within households in Lao PDR and association with housing characteristics and occupants' activities

The paper presents the results of a study conducted to investigate indoor air quality within residential dwellings in Lao PDR. Results from PM 10, CO, and NO2 measurements inside 167 dwellings in Lao PDR over a five month period (December 2005-April 2006) are discussed as a function of household characteristics and occupant activities. Extremely high PM10 and NO2 concentrations (12 h mean PM10 concentrations 1275 ± 98 μg m-3 and 1183 ± 99 μg m-3 in Vientiane and Bolikhamxay provinces, respectively; 12 h mean NO2 concentrations 1210 ± 94 μg m-3 and 561 ± 45 μg m-3 in Vientiane and Bolikhamxay, respectively) were measured within the dwellings. Correlations, ANOVA analysis (univariate and multivariate), and linear regression results suggest a substantial contribution from cookingandsmoking.The PM10 concentrations were significantly higher in houses without a chimney compared to houses in which cooking occurred on a stove with a chimney. However, no significant differences in pollutantconcentrations were observed as a function of cooking location. Furthermore, PM10 and NO2 concentrations were higher in houses in which smoking occurred, suggestive of a relationship between increased indoor concentrations and smoking (0.05 < p < 0.10). Resuspension of dust from soil floors was another significant source of PM10 inside the house (634 μg m-3, p < 0.05).

Source characterisation of road dust based on chemical and mineralogical composition

Road dust contain potentially toxic pollutants originating from a range of anthropogenic sources common to urban land uses and soil inputs from surrounding areas. The research study analysed the mineralogy and morphology of dust samples from road surfaces from different land uses and background soil samples to characterise the relative source contributions to road dust. The road dust consist primarily of soil derived minerals (60%) with quartz averaging 40-50% and remainder being clay forming minerals of albite, microcline, chlorite and muscovite originating from surrounding soils. About 2% was organic matter primarily originating from plant matter. Potentially toxic pollutants represented about 30% of the build-up. These pollutants consist of brake and tire wear, combustion emissions and fly ash from asphalt. Heavy metals such as Zn, Cu, Pb, Ni, Cr and Cd primarily originate from vehicular traffic while Fe, Al and Mn primarily originate from surrounding soils. The research study confirmed the significant contribution of vehicular traffic to dust deposited on urban road surfaces.

Human health risk of toxic chemical pollutants generated from traffic and land use activities

The research project developed a quantitative approach to assess the risk to human health from heavy metals and polycyclic aromatic hydrocarbons in urban stormwater based on traffic and land use factors. The research outcomes are expected to strengthen the scientifically robust management and reuse of urban stormwater. The innovative methodology developed can be applied to evaluate human health risk in relation to toxic chemical pollutants in urban stormwater runoff and for the development of effective risk mitigation strategies.

Destruction of Chemical Agents in a Plasma Reactor with Working Gas of Hydrogen

The conceptual development of a simple scale-adaptive reactive pollutant dispersion model

The paper develops the basis for a self-consistent, operationally useful, reactive pollutant dispersion model, for application in urban environments. The model addresses the multi-scale nature of the physical and chemical processes and the interaction between the different scales. The methodology builds on existing techniques of source apportionment in pollutant dispersion and on reduction techniques of detailed chemical mechanisms. © 2005 Published by Elsevier Ltd.

Microfabries of lacustrine sediments to pollutant adsorption from a polluted Eutrophic lake, the Yangtze delta region

Two types of microfabrics relating to pollutant adsorption were studied in the scanning electronic microscope (SEM) in a polluted, eutrophic lake, the Yangtze delta region. Agglutinational texture or the aggregates of small particles are composed of clay minerals and fine organic fragments among the silty grains and the coatings with a thickness about 1 mu m were on the surfaces of the silty grains in the sediments. The chemical constituents of the aggregates and the coatings are K, Na, Ca, Mg, Si, Al, O, Fe, Ti, C, N and P determined in X-ray energy spectrometry connected with the SEM. In some cases, Pb was detected in the aggregates in the top sediment. It is suggested that nutrients and metals are adsorbed to the aggregates, which were formed by electrostatic attraction of physicochemical floes. The coatings on the surface of quartz grains were formed by the interaction of dissociated Al, Si, Fe, etc from silicates with dissolved N, P and C nutrients in interstitial water, which was aroused by human pollution to the lake in recent two decades.

Pollution and pollutant transport in the geosphere - An introduction to the symposium

Environmental research in earth sciences is focused on the geosphere, i.e. (1) waters and sediments of rivers, lakes and oceans, and (2) soils and underlying shallow rock formations,both water-unsaturated and -saturated. The subsurface is studied down to greater depths at sites where waste repositories or tunnels are planned and mining activities exist. In recent years, earth scientists have become more and more involved in pollution problems related to their classical field of interest, e.g. groundwater, ore deposits, or petroleum and non-metal natural deposits (gravel, clay, cement precursors). Major pollutants include chemical substances, radioactive isotopes and microorganisms. Mechanisms which govern the transport of pollutants are of physical, chemical (dissolution, precipitation, adsorption), or microbiological (transformation) nature. Land-use planning must reflect a sustainable development and sound scientific criteria. Today's environmental pollution requires working teams with an interdisciplinary background in earth sciences, hydrology, chemistry, biology, physics as well as engineering. This symposium brought together for the first time in Switzerland earth and soil scientists, physicists and chemists, to present and discuss environmental issues concerning the geosphere.