A comparative study of airborne particulate pollution at two bus stations of different site geography

Airborne particulate pollutant is considered to be one of the major harmful emissions produced by vehicle engines as it has been directly linked to serious health problems. Passengers spend long times at bus stations and may be exposed to high concentrations of pollution. Particle pollution at two bus stations in Brisbane, Australia were monitored. The two bus stations consisted of markedly different site geography and surroundings with one situated in a street canyon and the other elevated above ground level. The same flow of traffic operated through both stations. Real time measurements of ultrafine particle concentration, size distribution and meteorological conditions were carried out on the platform continuously over several days. The results showed that the particle number concentrations were significantly different at the two stations, suggesting that the layout of site geometry and surroundings was a dominant determining factor through the injection of fresh air into the station platforms and the rates of dilution.

Airborne particulate matter at a bus station : concentration levels and governing parameters

Traffic emissions are an important contributor to ambient air pollution, especially in large cities featuring extensive and high density traffic networks. Bus fleets represent a significant part of inner city traffic causing an increase in exposure to general public, passengers and drivers along bus routes and at bus stations. Limited information is available on quantification of the levels, and governing parameters affecting the air pollution exposure at bus stations. The presented study investigated the bus emissions-dominated ambient air in a large, inner city bus station, with a specific focus on submicrometer particles. The study’s objectives were (i) quantification of the concentration levels; (ii) characterisation of the spatio-temporal variation; (iii) identification of the parameters governing the emissions levels at the bus station and (iv) assessment of the relationship between particle concentrations measured at the street level (background) and within the bus station. The results show that up to 90% of the emissions at the station are ultrafine particles (smaller than 100 nm), with the concentration levels up to 10 times the value of urban ambient air background (annual) and up to 4 times the local ambient air background. The governing parameters affecting particle concentration at the station were bus flow rate and meteorological conditions (wind velocity). Particle concentration followed a diurnal trend, with an increase in the morning and evening, associated with traffic rush hours. Passengers’ exposure could be significant compared to the average outdoor and indoor exposure levels.

Quantification of particle emission characteristics and development of an emission model for use in transport microenvironments affected by traffic emissions

Vehicle emitted particles are of significant concern based on their potential to influence local air quality and human health. Transport microenvironments usually contain higher vehicle emission concentrations compared to other environments, and people spend a substantial amount of time in these microenvironments when commuting. Currently there is limited scientific knowledge on particle concentration, passenger exposure and the distribution of vehicle emissions in transport microenvironments, partially due to the fact that the instrumentation required to conduct such measurements is not available in many research centres. Information on passenger waiting time and location in such microenvironments has also not been investigated, which makes it difficult to evaluate a passenger’s spatial-temporal exposure to vehicle emissions. Furthermore, current emission models are incapable of rapidly predicting emission distribution, given the complexity of variations in emission rates that result from changes in driving conditions, as well as the time spent in driving condition within the transport microenvironment. In order to address these scientific gaps in knowledge, this work conducted, for the first time, a comprehensive statistical analysis of experimental data, along with multi-parameter assessment, exposure evaluation and comparison, and emission model development and application, in relation to traffic interrupted transport microenvironments. The work aimed to quantify and characterise particle emissions and human exposure in the transport microenvironments, with bus stations and a pedestrian crossing identified as suitable research locations representing a typical transport microenvironment. Firstly, two bus stations in Brisbane, Australia, with different designs, were selected to conduct measurements of particle number size distributions, particle number and PM2.5 concentrations during two different seasons. Simultaneous traffic and meteorological parameters were also monitored, aiming to quantify particle characteristics and investigate the impact of bus flow rate, station design and meteorological conditions on particle characteristics at stations. The results showed higher concentrations of PN20-30 at the station situated in an open area (open station), which is likely to be attributed to the lower average daily temperature compared to the station with a canyon structure (canyon station). During precipitation events, it was found that particle number concentration in the size range 25-250 nm decreased greatly, and that the average daily reduction in PM2.5 concentration on rainy days compared to fine days was 44.2 % and 22.6 % at the open and canyon station, respectively. The effect of ambient wind speeds on particle number concentrations was also examined, and no relationship was found between particle number concentration and wind speed for the entire measurement period. In addition, 33 pairs of average half-hourly PN7-3000 concentrations were calculated and identified at the two stations, during the same time of a day, and with the same ambient wind speeds and precipitation conditions. The results of a paired t-test showed that the average half-hourly PN7-3000 concentrations at the two stations were not significantly different at the 5% confidence level (t = 0.06, p = 0.96), which indicates that the different station designs were not a crucial factor for influencing PN7-3000 concentrations. A further assessment of passenger exposure to bus emissions on a platform was evaluated at another bus station in Brisbane, Australia. The sampling was conducted over seven weekdays to investigate spatial-temporal variations in size-fractionated particle number and PM2.5 concentrations, as well as human exposure on the platform. For the whole day, the average PN13-800 concentration was 1.3 x 104 and 1.0 x 104 particle/cm3 at the centre and end of the platform, respectively, of which PN50-100 accounted for the largest proportion to the total count. Furthermore, the contribution of exposure at the bus station to the overall daily exposure was assessed using two assumed scenarios of a school student and an office worker. It was found that, although the daily time fraction (the percentage of time spend at a location in a whole day) at the station was only 0.8 %, the daily exposure fractions (the percentage of exposures at a location accounting for the daily exposure) at the station were 2.7% and 2.8 % for exposure to PN13-800 and 2.7% and 3.5% for exposure to PM2.5 for the school student and the office worker, respectively. A new parameter, “exposure intensity” (the ratio of daily exposure fraction and the daily time fraction) was also defined and calculated at the station, with values of 3.3 and 3.4 for exposure to PN13-880, and 3.3 and 4.2 for exposure to PM2.5, for the school student and the office worker, respectively. In order to quantify the enhanced emissions at critical locations and define the emission distribution in further dispersion models for traffic interrupted transport microenvironments, a composite line source emission (CLSE) model was developed to specifically quantify exposure levels and describe the spatial variability of vehicle emissions in traffic interrupted microenvironments. This model took into account the complexity of vehicle movements in the queue, as well as different emission rates relevant to various driving conditions (cruise, decelerate, idle and accelerate), and it utilised multi-representative segments to capture the accurate emission distribution for real vehicle flow. This model does not only helped to quantify the enhanced emissions at critical locations, but it also helped to define the emission source distribution of the disrupted steady flow for further dispersion modelling. The model then was applied to estimate particle number emissions at a bidirectional bus station used by diesel and compressed natural gas fuelled buses. It was found that the acceleration distance was of critical importance when estimating particle number emission, since the highest emissions occurred in sections where most of the buses were accelerating and no significant increases were observed at locations where they idled. It was also shown that emissions at the front end of the platform were 43 times greater than at the rear of the platform. The CLSE model was also applied at a signalled pedestrian crossing, in order to assess increased particle number emissions from motor vehicles when forced to stop and accelerate from rest. The CLSE model was used to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses including 1 car travelling in 1 direction (/1 direction), 14 cars / 1 direction, 1 bus / 1 direction, 28 cars / 2 directions, 24 cars and 2 buses / 2 directions, and 20 cars and 4 buses / 2 directions. It was found that the total emissions produced during stopping on a red signal were significantly higher than when the traffic moved at a steady speed. Overall, total emissions due to the interruption of the traffic increased by a factor of 13, 11, 45, 11, 41, and 43 for the above 6 cases, respectively. In summary, this PhD thesis presents the results of a comprehensive study on particle number and mass concentration, together with particle size distribution, in a bus station transport microenvironment, influenced by bus flow rates, meteorological conditions and station design. Passenger spatial-temporal exposure to bus emitted particles was also assessed according to waiting time and location along the platform, as well as the contribution of exposure at the bus station to overall daily exposure. Due to the complexity of the interrupted traffic flow within the transport microenvironments, a unique CLSE model was also developed, which is capable of quantifying emission levels at critical locations within the transport microenvironment, for the purpose of evaluating passenger exposure and conducting simulations of vehicle emission dispersion. The application of the CLSE model at a pedestrian crossing also proved its applicability and simplicity for use in a real-world transport microenvironment.

Subtropical futures : Victoria Park re-imagined

Brisbane, the capital of Queensland, in South-East Queensland is situated on the Brisbane River, one of the largest rivers (and floodplains) on the east coast of Australia. The river defines the city and gives it its name. The river has been a natural place to accommodate some population growth for the city with high-density development that capitalises on the natural amenity, cycleways and a string of parks and the flatter land. The major floods of 2011 and the scare of 2013, has seen a more malevolent quality of the river and shift of thinking on its role within the city. The floods have made council, for the first time, acquire prime development sites near the river, with proposals for high density development and made them parks, at great cost. The pressure for population growth in Brisbane remains. 140,000 new dwellings are required by 2031. Brownfield sites are less plentiful and there is interest to rethink of some of the other strategic locations in the city away from the river on higher ground and steeper slopes. Some of these places are currently open spaces. Victoria Park Golf Course sits on a high ridge line and a very strategic part of the city just north of the city centre is one of the few remaining golf courses close to the centre of an Australian capital city. While it is a public course and a valuable community asset, it has been compromised by the recently completed northern busway with two bus stations constructed on its edges. It is bounded on the west and north-east by two major community facilities, the Queensland University of Technology (QUT) to the west and RBW Hospital at its northern end. In a city in need of urban consolidation, perhaps it is time to review the future of the golf course. This question has been investigated as a conjecture in the Master of Architecture program at the QUT. The project has been to re-imagine Victoria Park as a new city parkland and a place that makes an urban connection from the QUT to the hospital. This new urban precinct is be a medium to high-density transit oriented development that capitalises on the bus way stations and the proximity of the university and hospital. The precinct will frame/define/interact with the new major urban park for the city. A key question being addressed is how the design can embody and define principles of a subtropical urbanism. Students are identifying the appropriate street and block structure, density and built form to be accommodated on blocks that define and activate a rich sequence of streets and public spaces. The paper will present a critical overview of the project work that provides a lens to how future professionals may respond to these issue that will be the focus of their professional lives.

Discussions in Space

The Discussions in Space (DiS) offers an interactive, fast-paced social media channel for local governments, organisations or institutions to engage with local residents or visitors in public spaces, such as city squares, shopping malls, train or bus stations, museums. It facilitates a public discussion and opinion forum through the installation of a large public screen, which passers-by can directly interact with using their mobile phone’s SMS and/or Internet capabilities. The concise and fast-paced nature of the system is aimed to be particularly effective to engage with typically younger demographics, which may not provide their feedback through more traditional means.

Runaway and Throwaway Youth: Time for Policy Changes and Public Responsibility

The traditional American dream of owning a home, obtaining a college education, and working at a good, paying job is only that, a dream, for scores of homeless youth in America today. There is a growing street population of young people who have been thrown out of their homes by their caretakers or their families, and who face life-threatening situations each day. For these youth, the furthest thing in their lives is reaching the so-called “American Dream;” and their most immediate need is survival, simply living out the day in front of them. They have few options that lead to a decent and safe living environment. Their age, lack of work experience, and absence of a high school diploma make it most difficult to find a job. As a result, they turn to other means for survival; runaways and throwaways are most vulnerable to falling prey to the sex trade, selling drugs, or being lured into human trafficking, and some steal or panhandle. Street youth end up spending their nights in bus stations or finding a room in an abandoned building or an empty stairwell to sleep. Attempting to identify a specific number of homeless youth is difficult at best, but what is even more perplexing is our continued inability to effectively protect our children. We are left with a basic question framed by the fundamental tenets of justice: what is a community’s responsibility to its youth who, for whatever reason, end up living on the streets or in unsafe, abusive environments? The purpose of this paper is to briefly outline the characteristics of homeless youth, in particular differentiating between throwaways and runaways; explore the current federal response to homeless youth; and finally, address the nagging question that swirls around all children: can we aggressively aspire to be a community where every child is healthy and safe, and able to realize his or her fullest potential?

Hydro-sedimentary parameters measurements within the proglacial area of the Bossons glacier (Mont-Blanc massif, France)

This dataset presents hydro-sedimentary data within the Bossons glacier proglacial area. Bossons glacier is rapidly retreating and its proglacial area is deglaciated for ~ 30 years. It is an intriguing location to study periglacial, proglacial and subglacial erosion processes which requires estimating Total Dissolved Solid (TDS) and Total Suspended Solid (TSS) concentrations, and discharge. Measurements were performed at three distinct locations within Bosson glacier watershed : Bossons downstream (BDS), Bossons upstream (BUS) and Crosette (CRO). The latter is located at the glacier termini whereas BDS and BUS stations are farther downstream from the glacier, at 1.5 and 1.15 km, respectively .

Key quality factors and travellers profiles at interurban interchanges

La planificación y las políticas de transporte no pueden descuidar la calidad del servicio, considerando que influye notablemente en el cambio modal del coche hacia otros medios de transporte más sostenibles. El concepto se aplica también a los intercambiadores de transporte público, los nodos del sistema donde se cruzan las distintas redes del transporte público y privado. Aunque se han logrado numerosos avances para medir y evaluar la calidad en el sector del transporte público, se han dedicado relativamente pocos esfuerzos a investigar estos aspectos relacionados con la calidad de los intercambiadores del transporte público. Este trabajo de investigación se concentra en la calidad del servicio de la transferencia modal en los intercambiadores interurbanos, según la perspectiva de los viajeros. Su objetivo es identificar los factores clave de la calidad del servicio y los perfiles de los viajeros en los intercambiadores. La investigación es exploratoria y ofrece información acerca de la percepción de los viajeros intermodales relacionada con los aspectos de la calidad, aportando nuevos elementos y datos para adentrarse en estudios más detallados. La metodología del trabajo combina técnicas de análisis estadístico multivariante para analizar los datos de las encuestas sobre la satisfacción de los clientes y se subdivide en tres etapas. En primer lugar, se ha implementado el análisis de correspondencias múltiples para explorar los constructos latentes relacionados con la satisfacción de las características cualitativas de los intercambiadores interurbanos, identificando así los factores clave de la calidad. En segundo lugar, se ha aplicado un análisis de conglomerados de k-medias sobre los factores clave de calidad para clasificar a los viajeros en grupos de usuarios de transportes homogéneos, de acuerdo con su percepción de satisfacción, identificando de este modo los perfiles de los viajeros. Por último, se han formulado sugerencias y recomendaciones sobre la calidad para respaldar la formulación de políticas, estableciendo las prioridades para los intercambiadores interurbanos. La metodología se aplicó en cuatro intercambiadores interurbanos (estaciones de ferrocarriles o de autobuses ) en Madrid, Zaragoza, Gothenburg y Lion, analizando los datos recogidos mediante una encuesta de satisfacción del cliente llevada a cabo en 2011 en los cuatro casos de estudio, donde se interconectan distintos medios de transporte público y privado, de corta y larga distancia. Se recogieron datos sobre la satisfacción de los viajeros con 26 criterios de calidad, así como información sobre aspectos socio-económicos y pautas de comportamiento de viajes. Mediante el análisis de correspondencias múltiples se identificaron 4-5 factores clave de calidad en cada intercambiador, que se asocian principalmente con el sistema de emisión de billetes, el confort y la interconexión, mientras que los viajeros no perciben los temas clásicos como la información. Mediante el análisis de conglomerados se identificaron 2-5 perfiles de viajeros en cada intercambiador. Se reconocieron dos grupos de viajeros en casi todos los casos de estudio: viajeros de cercanía/trabajadores y turistas. Por lo que concierne a las prioridades para apoyar a las partes interesadas en la formulación de políticas, la expedición de billetes es el factor clave para los intercambiadores interurbanos españoles, mientras que la interconexión y los aspectos temporales se destacan en los intercambiadores de Francia y Suecia. Quality of Service can not be neglected in public transport planning and policy making, since it strongly influences modal shifts from car to more sustainable modes. This concept is also related to Public Transport interchanges, the nodes of the transport system where the different sub-systems of public passenger transport and personal vehicles meet. Although a lot of progress has been generally done to measure and assess quality in public transport sector, relatively little investigation has been conducted on quality at PT interchanges. This research work focusses on Quality of Service in the use of transfer facilities at interurban interchanges, according to current travellers’ perspective. It aims at identifying key quality factors and travellers profiles at interurban interchanges. The research is exploratory and offers insight into intermodal travellers’ perception on quality aspects, providing new elements and inputs for more definitive investigation. The methodology of the work combines multivariate statistical techniques to analyse data from customer satisfaction surveys and is subdivided in three steps. Firstly, multiple correspondence analysis was performed to explore latent constructs as concern satisfaction of quality attributes at interurban interchanges, thus identifying the so-called Key Quality Factor. Secondly, k-means cluster analysis was implemented on the key quality factors to classify travellers in homogeneous groups of transport users, according to their perception of satisfaction, thus identifying the so-called Travellers Profiles. Finally, hints and recommendations on quality were identified to support policy making, setting priorities for interurban interchanges. The methodology was applied at four interurban interchanges in Madrid, Zaragoza, Gothenburg and Lyon, analysing the data collected through a customer satisfaction survey carried out in 2011 at the four railway or bus stations where different modes of public and private transport are interconnected covering both short and long trips. Data on travellers’ satisfaction with 26 quality attributes were collected, as well as information on socio-economical and travel patterns. Through multiple correspondence analysis were identified 4-5 key quality factors per interchange. They are mainly related to ticketing, comfort and connectivity, while classical issues, as information, are not perceived as important by travellers’. Through cluster analysis were identified 2-5 travellers profiles per interchange. Two groups of travellers can be found in almost all case studies: commuter / business travellers and holiday travellers. As regards the priorities to support stakeholders in policy making, ticketing is the key-issue for the Spanish interurban interchanges, while connectivity and temporal issues emerge in the French and Swedish case studies.

Modelling bus lost time : an additional parameter influencing bus dwell time and station platform capacity at a BRT station platform

The common approach to estimate bus dwell time at a BRT station is to apply the traditional dwell time methodology derived for suburban bus stops. In spite of being sensitive to boarding and alighting passenger numbers and to some extent towards fare collection media, these traditional dwell time models do not account for the platform crowding. Moreover, they fall short in accounting for the effects of passenger/s walking along a relatively longer BRT platform. Using the experience from Brisbane busway (BRT) stations, a new variable, Bus Lost Time (LT), is introduced in traditional dwell time model. The bus lost time variable captures the impact of passenger walking and platform crowding on bus dwell time. These are two characteristics which differentiate a BRT station from a bus stop. This paper reports the development of a methodology to estimate bus lost time experienced by buses at a BRT platform. Results were compared with the Transit Capacity and Quality of Servce Manual (TCQSM) approach of dwell time and station capacity estimation. When the bus lost time was used in dwell time calculations it was found that the BRT station platform capacity reduced by 10.1%.

Busway platform bus capacity analysis

Bus Rapid Transit (BRT), because of its operational flexibility and simplicity, is rapidly gaining popularity with urban designers and transit planners. Earlier BRTs were bus shared lane or bus only lane, which share the roadway with general and other forms of traffic. In recent time, more sophisticated designs of BRT have emerged, such as busway, which has separate carriageway for buses and provides very high physical separation of buses from general traffic. Line capacities of a busway are predominately dependent on bus capacity of its stations. Despite new developments in BRT designs, the methodology of capacity analysis is still based on traditional principles of kerbside bus stop on bus only lane operations. Consequently, the tradition methodology lacks accounting for various dimensions of busway station operation, such as passenger crowd, passenger walking and bus lost time along the long busway station platform. This research has developed a purpose made bus capacity analysis methodology for busway station analysis. Extensive observations of kerbside bus stops and busway stations in Brisbane, Australia were made and differences in their operation were studied. A large scale data collection was conducted using the video recording technique at the Mater Hill Busway Station on the South East Busway in Brisbane. This research identified new parameters concerning busway station operation, and through intricate analysis identified the elements and processes which influence the bus dwell time at a busway station platform. A new variable, Bus lost time, was defined and its quantitative descriptions were established. Based on these finding and analysis, a busway station platform bus capacity methodology was developed, comprising of new models for busway station lost time, busway station dwell time, busway station loading area bus capacity, and busway station platform bus capacity. The new methodology not only accounts for passenger boarding and alighting, but also covers platform crowd and bus lost time in station platform bus capacity estimation. The applicability of this methodology was shown through demonstrative examples. Additionally, these examples illustrated the significance of the bus lost time variable in determining station capacities.

Modeling Bus Rapid Transit station bus queuing for Bus Rapid Transit station bus operation analysis

Stations on Bus Rapid Transit (BRT) lines ordinarily control line capacity because they act as bottlenecks. At stations with passing lanes, congestion may occur when buses maneuvering into and out of the platform stopping lane interfere with bus flow, or when a queue of buses forms upstream of the station blocking inflow. We contend that, as bus inflow to the station area approaches capacity, queuing will become excessive in a manner similar to operation of a minor movement on an unsignalized intersection. This analogy is used to treat BRT station operation and to analyze the relationship between station queuing and capacity. In the first of three stages, we conducted microscopic simulation modeling to study and analyze operating characteristics of the station under near steady state conditions through output variables of capacity, degree of saturation and queuing. A mathematical model was then developed to estimate the relationship between average queue and degree of saturation and calibrated for a specified range of controlled scenarios of mean and coefficient of variation of dwell time. Finally, simulation results were calibrated and validated.

How do driver compensation schemes affect bus system performance?: a comparison between fixed wage and "guerra por el boleto" in Santiago, Chile.

Two systems of bus driver compensation exist in Santiago, Chile. The majority of drivers are paid per passenger transported, which leads to drivers trying to maximize the number of passengers each one conveys. Some of these effects are beneficial, such as a more active effort to minimize the problem of bus bunching, while others, such as aggressive driving, can be harmful. Drivers are said to "race" and the term "War for the Fare" is commonly used. Drivers also pay freelance workers called "sapos" to provide spacing information. Similar phenomena occur in other Latin American capitals.The other system, a fixed wage, is used by 2 companies holding recently awarded concessions for routes feeding metro stations.This paper discusses, quantitatively and qualitatively, the effects of these two compensation systems on accidents, quality of service, attitudes of both users and drivers, and average waiting times for passengers.

Intermodal exchange stations in the city of Madrid

The City of Madrid is putting into operation Intermodal Exchange Stations (IESs) to make connections between urban and suburban transportation modes easier for users of public transportation. The purpose of this article is to evaluate the actual effects that the implementation of IESs in the City of Madrid has on the affected stakeholders: users, public transportation operators, infrastructure managers, the government, the abutters and other citizens. We develop a methodology intended to help assess the welfare gains and losses for each stakeholder. Then we apply this methodology to the case study of the Avenida de América IES in the city of Madrid. We found that it is indeed possible to arrive at win–win solutions for the funding of urban transportation infrastructure, as long as the cost-benefit ratio of the project is high enough. Commuters save travel time. Bus companies diminish their costs of operation. The abutters gain in quality of life. The private operator of the infrastructure makes a fair profit. And the government is able to promote these infrastructure facilities without spending more of its scarce budgetary resources.

Modeling and optimization of frequencies on congested bus lines

In this paper some mathematical programming models are exposed in order to set the number of services on a specified system of bus lines, which are intended to assist high demand levels which may arise because of the disruption of Rapid Transit services or during the celebration of massive events. By means of this model two types of basic magnitudes can be determined, basically: a) the number of bus units assigned to each line and b) the number of services that should be assigned to those units. In these models, passenger flow assignment to lines can be considered of the system optimum type, in the sense that the assignment of units and of services is carried out minimizing a linear combination of operation costs and total travel time of users. The models consider delays experienced by buses as a consequence of the get in/out of the passengers, queueing at stations and the delays that passengers experience waiting at the stations. For the case of a congested strategy based user optimal passenger assignment model with strict capacities on the bus lines, the use of the method of successive averages is shown.