Electron Beam Welding In-Process Control and Monitoring

This work presents the results of an investigation of processes in the melting zone during Electron Beam Welding(EBW) through analysis of the secondary current in the plasma.The studies show that the spectrum of the secondary emission signal during steel welding has a pronounced periodic component at a frequency of around 15–25 kHz. The signal contains quasi-periodic sharp peaks (impulses). These impulses have stochastically varying amplitude and follow each other inseries, at random intervals between series. The impulses have a considerable current (up to 0.5 A). It was established that during electron-beam welding with the focal spot scanning these impulses follow each other almost periodically. It was shown that the probability of occurrence of these high-frequency perturbation increases with the concentration of energy in the interaction zone. The paper also presents hypotheses for the mechanism of the formation of the high-frequency oscillations in the secondary current signal in the plasma.

Thick Section Laser Beam Welding of Structural Steels: Methods for Improving Welding Efficiency

Laser beam welding (LBW) is applicable for a wide range of industrial sectors and has a history of fifty years. However, it is considered an unusual method with applications typically limited to welding of thin sheet metal. With a new generation of high power lasers there has been a renewed interest in thick section LBW (also known as keyhole laser welding). There was a growing body of publications during 2001-2011 that indicates an increasing interest in laser welding for many industrial applications, and in last ten years, an increasing number of studies have examined the ways to increase the efficiency of the process. Expanding the thickness range and efficiency of LBW makes the process a possibility for industrial applications dealing with thick metal welding: shipbuilding, offshore structures, pipelines, power plants and other industries. The advantages provided by LBW, such as high process speed, high productivity, and low heat input, may revolutionize these industries and significantly reduce the process costs. The research to date has focused on either increasing the efficiency via optimizing process parameters, or on the process fundamentals, rather than on process and workpiece modifications. The argument of this thesis is that the efficiency of the laser beam process can be increased in a straightforward way in the workshop conditions. Throughout this dissertation, the term “efficiency” is used to refer to welding process efficiency, specifically, an increase in efficiency refers an increase in weld’s penetration depth without increasing laser power level or decreasing welding speed. These methods are: modifications of the workpiece – edge surface roughness and air gap between the joining plates; modification of the ambient conditions – local reduction of the pressure in the welding zone; modification of the welding process – preheating of the welding zone. Approaches to improve the efficiency are analyzed and compared both separately and combined. These experimentally proven methods confirm previous findings and contribute additional evidence which expand the opportunities for laser beam welding applications. The focus of this research was primarily on the effects of edge surface roughness preparation and pre-set air gap between the plates on weld quality and penetration depth. To date, there has been no reliable evidence that such modifications of the workpiece give a positive effect on the welding efficiency. Other methods were tested in combination with the two methods mentioned above. The most promising - combining with reduced pressure method - resulted in at least 100% increase in efficiency. The results of this thesis support the idea that joining those methods in one modified process will provide the modern engineering with a sufficient tool for many novel applications with potential benefits to a range of industries.

The effects of some variables on CO2 laser-MAG hybrid welding

The CO2-laser-MAG hybrid welding process has been shown to be a productive choice for the welding industry, being used in e.g. the shipbuilding, pipe and beam manufacturing, and automotive industries. It provides an opportunity to increase the productivity of welding of joints containing air gaps compared with autogenous laser beam welding, with associated reductions in distortion and marked increases in welding speeds and penetration in comparison with both arc and autogenous laser welding. The literature study indicated that the phenomena of laser hybrid welding are mostly being studied using bead-on-plate welding or zero air gap configurations. This study shows it very clearly that the CO2 laser-MAG hybrid welding process is completely different, when there is a groove with an air gap. As in case of industrial use it is excepted that welding is performed for non-zero grooves, this study is of great importance for industrial applications. The results of this study indicate that by using a 6 kW CO2 laser-MAG hybrid welding process, the welding speed may also be increased if an air gap is present in the joint. Experimental trials indicated that the welding speed may be increased by 30-82% when compared with bead-on-plate welding, or welding of a joint with no air gap i.e. a joint prepared as optimum for autogenous laser welding. This study demonstrates very clearly, that the separation of the different processes, as well as the relative configurations of the processes (arc leading or trailing) affect welding performance significantly. These matters influence the droplet size and therefore the metal transfer mode, which in turn determined the resulting weld quality and the ability to bridge air gaps. Welding in bead-onplate mode, or of an I butt joint containing no air gap joint is facilitated by using a leading torch. This is due to the preheating effect of the arc, which increases the absorptivity of the work piece to the laser beam, enabling greater penetration and the use of higher welding speeds. With an air gap present, air gap bridging is more effectively achieved by using a trailing torch because of the lower arc power needed, the wider arc, and the movement of droplets predominantly towards the joint edges. The experiments showed, that the mode of metal transfer has a marked effect on gap bridgeability. Transfer of a single droplet per arc pulse may not be desirable if an air gap is present, because most of the droplets are directed towards the middle of the joint where no base material is present. In such cases, undercut is observed. Pulsed globular and rotational metal transfer modes enable molten metal to also be transferred to the joint edges, and are therefore superior metal transfer modes when bridging air gaps. It was also found very obvious, that process separation is an important factor in gap bridgeability. If process separation is too large, the resulting weld often exhibits sagging, or no weld may be formed at all as a result of the reduced interaction between the component processes. In contrast, if the processes are too close to one another, the processing region contains excess molten metal that may create difficulties for the keyhole to remain open. When the distance is optimised - i.e. a separation of 0-4 mm in this study, depending on the welding speed and beam-arc configuration - the processes act together, creating beneficial synergistic effects. The optimum process separation when using a trailing torch was found to be shorter (0-2 mm) than when a leading torch is used (2-4 mm); a result of the facilitation of weld pool motion when the latter configuration is adopted. This study demonstrates, that the MAG process used has a strong effect on the CO2-laser-MAG hybrid welding process. The laser beam welding component is relatively stable and easy to manage, with only two principal processing parameters (power and welding speed) needing to be adjusted. In contrast, the MAG process has a large number of processing parameters to optimise, all of which play an important role in the interaction between the laser beam and the arc. The parameters used for traditional MAG welding are often not optimal in achieving the most appropriate mode of metal transfer, and weld quality in laser hybrid welding, and must be optimised if the full range of benefits provided by hybrid welding are to be realised.

Green welding in practice

Efficient production and consumption of energy has become the top priority of national and international policies around the world. Manufacturing industries have to address the requirements of the government in relation to energy saving and ecologically sustainable products. These industries are also concerned with energy and material usage due to their rising costs. Therefore industries have to find solutions that can support environmental preservation yet maintain competitiveness in the market. Welding, a major manufacturing process, consumes a great deal of material and energy. It is a crucial process in improving a product’s life-cycle cost, strength, quality and reliability. Factors which lead to weld related inefficiencies have to be effectively managed, if industries are to meet their quality requirements and fulfil a high-volume production demand. Therefore it is important to consider some practical strategies in welding process for optimization of energy and material consumption. The main objective of this thesis is to explore the methods of minimizing the ecological footprint of the welding process and methods to effectively manage its material and energy usage in the welding process. The author has performed a critical review of the factors including improved weld power source efficiency, efficient weld techniques, newly developed weld materials, intelligent welding systems, weld safety measures and personnel training. The study lends strong support to the fact that the use of eco-friendly welding units and the quality weld joints obtained with minimum possible consumption of energy and materials should be the main directions of improvement in welding systems. The study concludes that, gradually implementing the practical strategies mentioned in this thesis would help the manufacturing industries to achieve on the following - reduced power consumption, enhanced power control and manipulation, increased deposition rate, reduced cycle time, reduced joint preparation time, reduced heat affected zones, reduced repair rates, improved joint properties, reduced post-weld operations, improved automation, improved sensing and control, avoiding hazardous conditions and reduced exposure of welder to potential hazards. These improvement can help in promotion of welding as a green manufacturing process.

Heat Treatment and Yb-Fiber Laser Welding of a Maraging Steel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Study and experimental characterization of the laser welding process for the manufacturing of electric powertrain components in the automotive industry

The PhD project that will be presented in this thesis is focused on the study and optimization of the production process for the manufacturing of electrical powertrain components in the automotive field using the laser beam welding process (LBW). The objective is to define, through experimental activities, an optimized process condition for applications in the electrical field that can be generalized, that is, which guarantees its reproducibility as the types of connections vary and which represents the basis for extending the method to future applications in e-mobility sector. The work developed along two lines of research, the convergence of which made it possible to create prototypes of battery modules based on different types of lithium-ion cells and stator windings for electric motors. On the one hand, the different welding configurations involving the production of batteries based on pouch cells and therefore the welding of aluminum and copper in dissimilar configuration were studied, while for the prismatic cells only one configuration was analyzed. On the other hand, the welding of pure copper hairpins with rectangular shape in edge joint configuration was studied for the production of stator windings. The experimental tests carried out have demonstrated the feasibility of using the LBW process for the production of electric powertrain components entirely designed and developed internally as the types of materials and welding configurations vary; the methodologies required for the characterization methods, necessary for the end-of-line tests, for the evaluation of the properties of the different joint configurations and components (battery and electric motor) were also defined with the aim of obtaining the best performance. The entire doctorate program was conducted in collaboration with Ferrari Auto S.p.A. and the direct industrial application of the issues addressed has been faced.

Schweißgerechte Struktur- und Prozessstrategien im Flugzeugbau

Aluminium, Fuselage,Fuselage Construction, Hot Cracking, Laser Beam Welding, Stringer, Weldability, Welding, Welding Process, Airbus, A318, A380, AA6013, AA6056

Hitsausmenetelmät ja niiden kehittämismahdollisuudet painelaitteiden valmistuksessa

Työn tavoitteena oli painelaitteiden hitsaustuotannon kehittäminen. Keinoina olivat käytössä olevien hitsausprosessienkehittäminen tai niiden käytön tehostaminen ja mahdollisesti muiden hitsausprosessien, kuten plasma-, laser- tai hybridihitsauksen, käyttöönotto. Työn teoriaosassa käsiteltiin painelaitteiden valmistuksessa käytettävät hitsausprosessit ja niiden kehittämiskeinot, hitsauskustannuksen muodostuminen sekä miten näihin kustannuksiin voidaan vaikuttaa. Lisäksi tarkasteltiin painelaitteiden valmistuksessa käytettävien materiaalien hitsattavuutta ja laadunvarmistusta. Tutkimusosuudessa käytiin läpi valmistuksen nykytila ja tehtiin tuotannon analysointi kehittämiskohteeksi valitulle lämmönsiirtimelle. Kehitysehdotuksenatuotannon tehostamiseksi ehdotettiin MAG-täytelanka- ja jauhekaarihitsauksen käytön lisäämistä. Lisäksi ehdotettiin juurituen käyttöä ja hitsauksen mekanisoinnin lisäämistä. Plasma- tai hybridihitsauksen käytöllä todettiin pystyttävän lyhentämään läpimenoaikoja. Ennen laitteistohankintojen tekoa täytyy tehdä lisäselvityksiä soveltuvuuden ja kannattavuuden varmistamiseksi.

Modeling dynamic behavior in tilting pad gas journal bearings

Thisresearch deals with the dynamic modeling of gas lubricated tilting pad journal bearings provided with spring supported pads, including experimental verification of the computation. On the basis of a mathematical model of a film bearing, a computer program has been developed, which can be used for the simulation of a special type of tilting pad gas journal bearing supported by a rotary spring under different loading conditions time dependently (transient running conditions due to geometry variations in time externally imposed). On the basis of literature, different transformations have been used in the model to achieve simpler calculation. The numerical simulation is used to solve a non-stationary case of a gasfilm. The simulation results were compared with literature results in a stationary case (steady running conditions) and they were found to be equal. In addition to this, comparisons were made with a number of stationary and non-stationary bearing tests, which were performed at Lappeenranta University of Technology using bearings designed with the simulation program. A study was also made using numerical simulation and literature to establish the influence of the different bearing parameters on the stability of the bearing. Comparison work was done with literature on tilting pad gas bearings. This bearing type is rarely used. One literature reference has studied the same bearing type as that used in LUT. A new design of tilting pad gas bearing is introduced. It is based on a stainless steel body and electron beam welding of the bearing parts. It has good operation characteristics and is easier to tune and faster to manufacture than traditional constructions. It is also suitable for large serial production.

Kehittyneiden hitsausprosessien soveltuvuus alumiinin ja hiiliterästen hitsaukseen

Diplomityössä tutkitaan hitsausprosessien kehitystä. Työn kirjallisen osan alku kuvaa hitsauksen nykypäivää ja tulevaisuutta sekä millainen on hitsaava Suomi. Kehittyneiden hitsausprosessien tarkastelu on jaettu hiiliterästen ja alumiinien hitsausprosesseihin. Hiiliteräksien hitsauksen osalta työssä esitellään kitkahitsaus pyörivällä työkalulla, muunnettu lyhytkaarihitsaus, laserhitsaus, laser-hybridihitsaus ja kapearailohitsaus. Alumiinien hitsauksen osalta työssä esitellään laserhitsaus, muunnettu lyhytkaarihitsaus, kitkahitsaus pyörivällä työkalulla ja vaihtovirta MIG hitsaus. Diplomityön käytännönosuudessa todennettiin hitsausprosessien kehitys. Ensimmäisissä hitsauskokeissa hitsattiin merialumiinia eri kaarityypeillä. Vertailua tehdään pulssihitsauksen, lankapulssihitsauksen sekä CMT-kaarihitsauksen välillä. Koehitsaukset osoittavat CMT-hitsauksen tuottavan MIG-pulssihitsausta pienemmät hitsausmuodonmuutokset. CMT-hitsauksessa alumiinin oksidikerros aiheuttaa MIGpulssihitsausta vähemmän ongelmia, sillä kaari syttyy varmemmin suurillakin hitsausnopeuksilla, eikä hitsiin synny huokosia. Hitsausnopeudella 40 cm/min lankapulssihitsauksella ja MIG-pulssihitsauksella päittäisliitoksena hitsattujen vesileikattujen alumiinikappaleiden hitseihin ei syntynyt huokosia. Kokeen perusteella voidaan todeta, ettei oksidikerroksella ollut vaikutusta hitsin onnistumiseen. Hitsauskokeiden toinen osio tutkii hiilimangaaniteräksisen T-palkin kuitulaserhitsausta. Viiden kilowatin laserteholla hitsattiin onnistuneesti viisi metriä pitkiä T-palkkeja hitsausnopeudella 2 m/min. Takymetrimittauksella ja Tritop 3D-koordinaattimittauksella todennettiin laserhitsatun T-palkin hitsausmuodonmuutosten olevan huomattavasti Twin-jauhekaarihitsauksella hitsattua T-palkkia pienemmät.

Kuparin hitsaus kattavilla laatuvaatimuksilla

Kuparin ja kupariseosten hitsaus eroaa merkittävästi esimerkiksi terästen hitsauksesta. Suuri lämmönjohtavuus, lämpölaajeneminen, pehmeneminen ja kuparin taipumus liuottaa kaasuja sulaan asettavat hitsaukselle haasteita. Kuparia on perinteisesti hitsattu kaasuhitsaamalla ja kaasukaarihitsausprosesseilla, mutta uudemmat menetelmät kuten laserhitsaus, elektronisuihkuhitsaus ja FSW-hitsaus tarjoavat uudenlaisia käyttökohteita korkealla laadulla. ISO 3834-2 asettaa noudatettavat vaatimukset hitsaustoiminnalle laatuvaatimusten ollessa kattavia. Ydinvoimalaitoksella hitsauksessa tulee lisäksi noudattaa Säteilyturvakeskuksen YVL-ohjeita, joissa on määritetty lisävaatimuksia liitosten materiaalivalinnoille, pätevöittämiselle ja tarkastamiselle. Tässä työssä tutkittiin kuparimetallien hitsauksen mahdollisuutta Loviisan ydinvoimalaitoksella juottamisen sijasta siten, että kattavat laatuvaatimukset täyttyisivät. Hitsauskokeissa ja laboratoriotutkimuksissa testattiin hitsausta erilaisilla hitsausaineilla ja hitsausprosesseilla. Koetulosten pohjalta toteutettiin hitsausmenetelmä deoksidoidun kupariputken ja tinapronssilaipan TIG-hitsaukselle.

Investigação da Interface Metal-Porcelana da Liga Ni-Cr-Mo Soldada a LASER

The interface formed between the metal and the porcelain of a LASER welded Ni-Cr-Mo alloy was studied. The characterization was carried out through optical microscopy, scanning electron microscopy, X-ray dispersive spectroscopy-EDS and mechanical testing by three-point flexion test-TPE in the region LASER welded with and without the porcelain. The porcelain adhesion with the alloy alone is possible after the oxidation of the metallic surface and subsequent application of an adhesive called opaco. The applied porcelain, on the base metal and fusion zone presented some distinct behaviors. After the TPF test the base metal presented fractures while that in the fusion zone was completely gone. One noticed that the region submitted to the LASER welding showed less porcelain adhesion than the region of the base metal due to the microestructural refinement of the fusion zone. These results can be evidenced by the EDS of the studied regions. The TPF had demonstrated that the Ni-Cr-Mo alloy submitted to the LASER welding, undergone significant alterations in its mechanical properties after the application of the porcelain.

Influência da energia de soldagem em uniões de lâminas finas através de laser pulsado de Nd:YAG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Investigation of the metal/porcelain interface in LASER-welded Ni-Cr-Mo alloy

The interface formed between the metal and the porcelain of laser-welded Ni-Cr-Mo alloy was studied on a metallurgical basis. The characterization was carried out by using optical microscope, electron scan microscopy and X-ray dispersive spectroscopy techniques and mechanical three-point flexion tests, in the laser-welded region, with and without porcelain. The union of the porcelain with the alloy is possible only after the oxidation of the metallic surface and the subsequent application of a bonding agent known as opaque. The porcelain applied to the base metal and weld bead showed different behaviours - after the flexion test, the base metal showed cracks, while that in the weld bead broke away completely. It was noted that the region subjected to laser welding had lower adherence to the porcelain than the base metal region, due to microstructural refinement of the weld bead. These results can be shown by the X-ray dispersive spectroscopy carried out on the regions studied. The flexion tests demonstrated that the Ni-Cr-Mo alloy subject to laser welding had significant alterations in its mechanical properties after application of the porcelain.

Caracterização mecânica e microestrutural de juntas de alumínio 6013 T4 soldados a laser

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)