Flow resistance network analysis of the back-pressure of automotive mufflers

Complexity of mufflers generally introduces considerable pressure drop, which affects the engine performance adversely. Not much literature is available for pressure drop across perforates. In this paper, the stagnation pressure drop across perforated muffler elements has been measured experimentally and generalized expressions have been developed for the pressure loss across cross-flow expansion and cross-flow contraction elements. A flow resistance model available in the literature has been made use of to analytically determine the flow distribution and thereby the pressure drop of mufflers. A generalized expression has been derived here for evaluation of the equivalent flow resistance for parallel flow paths. Expressions for flow resistance across perforated elements, derived by means of flow experiments, have been implemented in the flow resistance network. The results have been validated with experimental data. Thus, the newly developed integrated flow resistance networks would enable us to determine the normalized stagnation pressure drop of commercial automotive mufflers, thus enabling an efficient flow-acoustic design of silencing systems.

The sexual motivation of boars housed adjacent to ovariectomised gilts did not affect the efficiency of detecting hormonally induced oestrus using the back pressure test

This study tested the hypothesis that the efficiency of detecting oestrus in gilts, using the back pressure test (BPT), will be reduced when gilts are housed adjacent to a boar of high sexual motivation compared to when gilts are housed adjacent to a boar of low sexual motivation. The experiment was a 2 x 2 Latin square design with three replicates. Boars of high and low sexual motivation were selected on the basis of the total number of copulations and the mean reaction time to first mount during three mating tests. Twelve boars were observed in mating tests and the three highest and lowest ranking boars were assigned to three palm, each pair containing a boar of high and a boar of low sexual motivation. One pair was used in each replicate. In each replicate, two groups of six ovariectomised gilts were housed for 14 days, commencing 7 days prior to hormonally induced destrus, adjacent to a boar of either high or low sexual motivation. All gilts were checked twice daily for oestrus using the BPT. In the first replicate, the level of proceptive behaviour of the gilts was quantified immediately after checking for oestrus in a 3-rain test in which the amount of time that the gilts spent within 0.5 m of a pen containing a sexually mature boar was recorded. There were no effects of housing gilts adjacent to boars of high or low sexual motivation on the percentage of gilts detected in oestrus, the percentage of gilts detected in oestrus for more than I day, the duration of oestrus or the level of proceptive behaviour of gilts. These data suggest that the level of sexual motivation of boars does not influence the efficiency of detecting hormonally induced oestrus, using the BPT, in ovariectomised gilts housed adjacent to boars.

Manual for back pressure test for natural gas wells, State of New Mexico,

Mode of access: Internet.

Thermal behavior of copper processed by ECAP with and without back pressure

Samples of electrolytic tough pitch (ETP) pure copper were subjected to 12 passes of Equal-Channel Angular Pressing (ECAP) at room temperature with and without back pressure. Subsequent annealing was performed to evaluate the influence of back pressure during ECAP on the thermal behavior of ultrafine-grained copper. The microstructural and hardness changes caused by annealing were characterized by orientation imaging microscopy (OIM) and microhardness measurements. The application of back pressure resulted in an earlier drop in hardness upon annealing, which is believed to be associated with a lower critical temperature for the initiation of recrystallization and a rapid coarsening of microstructure. Regardless of whether back pressure was applied or not, structure coarsening during short-time annealing of ECAP-processed copper was governed by discontinuous static recrystallization. This is seen as a result of microstructure heterogeneity. Analysis of recrystallization kinetics was carried out based on observations of the microstructure after annealing in terms of the Avrami equation. The magnitude of the apparent activation energies for recrystallization in the absence of back pressure and in the case of back pressure of 100 MPa was estimated to be ~99 kJ/mol and ~91 kJ/mol, respectively. The reasons for reduced activation energy in the case of processing with back pressure are discussed.

Enhanced superplasticity of magnesium alloy AZ31 obtained through equal-channel angular pressing with back-pressure

Excellent superplastic elongations (in excess of 1,200%) were achieved in a commercial cast AZ31 alloy processed by low temperature equal-channel angular pressing (ECAP) with a back-pressure to produce a bimodal grain structure. In contrast, AZ31 alloy processed by ECAP at temperatures higher than 200 °C showed a reasonably uniform grain structure and relatively low ductility. It is suggested that a bimodal grain structure is advantageous because the larger grains contribute to strain hardening thus delaying the onset of necking, while grain boundary sliding associated with small grains provides a stabilizing effect due to enhanced strain rate sensitivity. © 2008 Springer Science+Business Media, LLC.

Low-temperature compaction of Ti-6Al-4V powder using equal channel angular extrusion with back pressure

Equal channel angular extrusion (ECAE), with simultaneous application of back pressure, has been applied to the consolidation of 10 mm diameter billets of pre-alloyed, hydride-dehydride Ti-6Al-4V powder at temperatures ≤400 °C. The upper limit to processing temperature was chosen to minimise the potential for contamination with gaseous constituents potentially harmful to properties of consolidated product. It has been demonstrated that the application of ECAE with imposed hydrostatic pressure permits consolidation to in excess of 96% relative density at temperatures in the range 100-400 °C, and in excess of 98% at 400 °C with applied back pressure ≥175 MPa. ECAE compaction at 20 °C (back pressure = 262 MPa) produced billet with 95.6% relative density, but minimal green strength. At an extrusion temperature of 400 °C, the relative density increased to 98.3%, for similar processing conditions, and the green strength increased to a maximum 750 MPa. The relative density of compacts produced at 400 °C increased from 96.8 to 98.6% with increase in applied back pressure from 20 to 480 MPa, while Vickers hardness increased from 360 to 412 HV. The key to the effective low-temperature compaction achieved is the severe shear deformation experienced during ECAE, combined with the superimposed hydrostatic pressure.

Enhanced superplasticity in a magnesium alloy processed by equal-channel angular pressing with a back-pressure

An investigation was initiated to evaluate the feasibility of using equal-channel angular pressing (ECAP) to obtain high superplastic elongations in the AZ31 alloy with a back pressure producing a bimodal grain structure. Processing by ECAP was performed using a die with an angle of 90 ° between the two parts of the channel and a ram velocity of 15-20 mm/sec. Some pressing were conducted with a back-pressure by making use of a backward punch in the exit channel of the die. Molybdenum disulphide and a graphite spray were used as lubricants and billets were pressed using processing route B c in which each billet is rotated by 90 °. The pressing were conducted at temperatures in the range from 423 to 523 K and every billet was quenched in water after each pass. The significance of the bimodal microstructure is attributed to the ability of the larger grains to more easily accommodate grain boundary sliding through intragranular slip and twinning and to contribute to the strain hardening capability.

Deformation field variations in equal channel angular extrusion due to back pressure

Flow lines were analysed in aluminium alloy 6061 during equal channel angular extrusion (ECAE) in a 90° die with and without the application of back pressure during pressing. The lines appeared much more rounded when a back pressure was applied compared to the case of conventional ECAE testing. With the help of an analytic flow function, the deformation field was obtained. It is shown that back pressure slightly lowers the total strain, strongly increases the size of the plastic zone and significantly reduces the plastic strain rate.

Effect of back pressure during equal-channel angular pressing on deformation-induced porosity in copper

The effect of back pressure during equal channel angular pressing (ECAP) on deformation-induced porosity is investigated. While percolating porosity was found after 4 ECAP passes in the absence of back pressure, no percolation was detected when a back pressure of 200 MPa was applied. However, after ECAP with back pressure continued to 8 passes, percolating porosity did appear. The nature of the percolating porosity developed in severely deformed materials is discussed.

Effect of processing parameters on the magnetic properties and macrotexture of a Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy processed by equal channel angular pressing with back pressure

Equal channel angular pressing (ECAP) is a well-established thermo-mechanical processing technique, which could induce the c-axis texture of Nd2Fe14B in a melt-spun Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy. However, the effects of ECAP processing parameters, such as temperature, back pressure (BP), and multiple-pass ECAP routes, remain unknown for this alloy. In this paper, we have investigated the effects of these processing parameters on the c-axis texture formation. It is found by X-ray diffraction macrotexture analysis that the maximum intensity of (001) pole figures for the tetragonal-Nd2Fe14B phase (Imax) shows an increase from 2.7 to 4.1 m.r.d. (multiples of random distribution) by increasing the ECAP temperature from 723 to 823 K, while the difference in remanent magnetization between easy and hard directions (Δ Mr) rises from 24.0 to 41.5 Am2/kg. When the BP was increased from 0.25 to 0.5 GPa at 823 K, Imax showed an increase from 2.8 to 4.1 m.r.d. However, Imax saturated for BPs above 0.5 GPa, suggesting that BP has limited effect on the texture formation, although it is necessary for the compaction of the alloy powders. Two multiple-pass ECAP routes conventionally known as routes A and C were employed for two-pass ECAP at 823 K. It is found that route A processing is effective in enhancing the texture formation, while the texture is lost by a subsequent pressing when adopting route C. Therefore, the compaction of Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy powder using route A ECAP passes with 0.5 GPa BP at 823 K results in pronounced texture, which is beneficial for anisotropic hard magnetic properties.

Pore fluid pressure at DSDP Leg 84 Holes

Evidence of considerable overpressuring of pore fluids in the sediment drilled during Leg 84 was obtained from direct measurement of pressure by two methods. The first involved measurement of back pressure when the annulus of the drill hole became constricted with unremoved drill cuttings or constriction was caused by plastic inflow of the drill hole walls. The second involved measurement of pressure ahead of the bit in conjunction with in situ water samples and heat flow. All measurements indicated abnormally high pore pressure even in slope deposits of the Middle America Trench off Guatemala.

Shear deformation with imposed hydrostatic pressure for enhanced compaction of powder

In this paper equal channel angular extrusion with back pressure was used to compact Ti-6Al-4V powder at 400 °C, achieving relative densities of 98.3-98.6% and green strengths up to 750 MPa. The novelty of the approach arises from the notion that severe shear deformation is an important factor for consolidation. Improved compaction is related to enhanced self-diffusion through the creation of additional diffusion paths (defects) and the imposed hydrostatic pressure. The role of deformation mechanisms in improving compaction is discussed. © 2008 Acta Materialia Inc.

Effect of engine backpressure on the performance and emissions of a CI engine

This study investigated the effect of engine backpressure on the performance and emissions of a CI engine under different speed and load conditions. A 4-stroke single cylinder naturally aspirated direct injection (DI) diesel engine was used for the investigation with the backpressure of 0, 40, 60 and 80 mm of Hg at engine speed of 600, 950 and 1200 rpm. Two parameters were measured during the engine operation: one is engine performance (brake thermal efficiency and brake specific fuel consumption), and the other is the exhaust emissions (NOx, CO and odor). NOx and CO emission were measured by flue gas analyzer (IMR 1400). The engine backpressure produced by the flow regulating valve in the exhaust line was measured by Hg (mercury) manometer. The result showed that, the brake thermal efficiency and brake specific fuel consumption (bsfc) are almost unchanged with increasing backpressure up to 40 mm of Hg pressure for all engine speed and load conditions. The NOx emission became constant or a little decreased with increasing backpressure. The formation of CO was slightly higher with increase of load and back pressure at low engine speed condition. However, under high speed conditions, CO reduced significantly with increasing backpressure for all load conditions. The odor level was similar or a little higher with increasing backpressure for all engine speed and load conditions. Hence, backpressure up to a certain level is not detrimental for a CI engine.

A New Liquid Level Sensor for Process-Control Applications

Many process-control systems are air-operated. In such an environment, it would be desirable and economical to use pneumatic sensors. Bubble-back pressure sensors perform quite satisfactorily, but in case of viscous inflammable and slurry-like liquids with a tendency to froth, this level sensor is inadequate. The method suggested in this paper utilizes a pneumatic capacitor, one boundary of which is formed by the liquid level, to modulate a fluid amplifier feedback oscillator. The absence of moving parts and economy obtained makes this method attractive for process-control applications. The system has been mathematically modeled and simulated on an IBM 360/44 digital computer. Experimental values compare fairly well with the theoretical results. For the range tested, the sensor is found to have a linear frequency variation with the liquid level Extended running in the laboratory shows that the system is very reliable. This system has been found insensitive to temperature variations of up to 15ðC.

Tuning of the extended concentric tube resonators

It has been shown recently that the acoustic performance of the extended tube expansion chambers can be improved substantially by making the extended inlet and outlet equal to half and quarter chamber lengths, duly incorporating the end corrections due to the evanescent higher order modes that would be generated at the discontinuities. Such chambers however suffer from the disadvantages of high back pressure and generation of aerodynamic noise at the area discontinuities. These two disadvantages can be overcome by means of a perforated bridge between the extended inlet and extended outlet. This paper deals with design or tuning of these extended concentric tube resonators.