Effects of anode temperature on working characteristics and performance of a low power arcjet thruster

An arc-heated thruster of 130–800 W input power is tested in a vacuum chamber at pressures lower than 20 Pa with argon or H2–N2 gas mixture as propellant. The time-dependent arc voltage-current curve, outside-surface temperature of the anode nozzle and the produced thrust of the firing arcjet thruster are measured in situ simultaneously, in order to analyze and evaluate the dependence of thruster working characteristics and output properties, such as specific impulse and thrust efficiency, on nozzle temperature.

Effect of Nozzle Temperature on the Performance of a 1 kW H2-N2 Arcjet Thruster

A 1 kW-class arcjet thruster was ¯red in a vacuum chamber at a pressure of 18 Pa. A gas mixture of H2 : N2 = 2.8 : 1.5 in volume at a total °ow rate of 4.3 slm was used as the propellant with an input power ¯xed at 860 W. The time-dependent thrust, nozzle temperature and inlet pressure of the propellant were measured simultaneously. Results showed that with the increase in nozzle temperature the thrust decreased and various losses increased. The physical mechanisms involved in these effects are discussed.

Plasma and electrode emissions from a 1 kW hydrogen-nitrogen arcjet thruster

Arc root behavior affects the energy transfer and nozzle erosion in an arcjet thruster. To investigate the development of arc root attachment in 1 kW class N2 and H2-N2 arcjet thrusters from the time of ignition to the stably working condition, a kinetic series of end-on view images of the nozzle obtained by a high-speed video camera was analyzed. The addition of hydrogen leads to higher arc voltage levels and the determining factor for the mode of arc root attachment was found to be the nozzle temperature. At lower nozzle temperatures, constricted type attachment with unstable motions of the arc root was observed, while a fully diffused and stable arc root was observed at elevated nozzle temperatures.

Numerical modeling of heat transfer and plasma flow in a low power arcjet thruster

Modeling studies are preformed to investigate the plasma and heat transfer characteristics of a low power argon arcjet thruster. Computed temperature, velocity, static pressure, and Mach number distribution in arcjet thruster under typical operating condition are presented in this paper. It shows that the performance data from numerical modeling results are basically consistent with the experimental measured values.

Experimental study on energy dissipation in a 1 kW arcjet thruster

As a simple and reliable propulsion system, arcjet thrusters have been used in multiple satellite missions. In order to improve the efficiency of arcjet thrusters, energy dissipation study was carried out in a 1 kW arcjet thruster with pure N2, H2-N2 and H2 as the propellant. Using a 698 nm interference filter, thermal radiation was isolated from arc and plume emissions and the internal nozzle temperature was obtained by converting the thermal radiation signals. Results show that the addition of hydrogen leads to higher nozzle temperature, which is the determining factor for the mode of arc root attachment. At lower nozzle temperatures, constricted type attachment with unstable motions of the arc root was observed, while a fully diffused and stable arc root was observed at elevated nozzle temperatures. Output energy distribution analysis shows that losses from frozen flow and exhaust thermal losses are the main parts in limiting the efficiency of arcjet thrusters.

Experimental study on energy dissipation in a 1 kW arcjet thruster

As a simple and reliable propulsion system, arcjet thrusters have been used in multiple satellite missions. In order to improve the efficiency of arcjet thrusters, energy dissipation study was carried out in a 1 kW arcjet thruster with pure N2, H2-N2 and H2 as the propellant. Using a 698 nm interference filter, thermal radiation was isolated from arc and plume emissions and the internal nozzle temperature was obtained by converting the thermal radiation signals. Results show that the addition of hydrogen leads to higher nozzle temperature, which is the determining factor for the mode of arc root attachment. At lower nozzle temperatures, constricted type attachment with unstable motions of the arc root was observed, while a fully diffused and stable arc root was observed at elevated nozzle temperatures. Output energy distribution analysis shows that losses from frozen flow and exhaust thermal losses are the main parts in limiting the efficiency of arcjet thrusters.

Numerical Simulation of a Low-power Hydrazine Arcjet Thruster

A modeling study is conducted to investigate the plasma flow and heat transfer characteristics of low-power (kW class) arc-heated thrusters (arcjets) with 2:1 hydrogen/nitrogen to simulate decomposed hydrazine as the propellant. The all-speed SIMPLE algorithm is employed to solve the governing equations, which take into account the effects of compressibility, the Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. Typical computed results about the temperature, velocity and Mach number distributions within arcjet thruster are presented for the case with arc current of 9 A and inlet stagnant pressure of 3.3×105 Pa to show the flow and heat transfer characteristics. It is found that the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appearing near the cathode tip, and the flow transition from the subsonic to supersonic regime occurs within the constrictor region. The effect of gas viscosity on the plasma flow within arcjet thruster is examined by an additional numerical test using artificially reduced values of gas viscosity. The test results show that the gas viscosity appreciably affects the plasma flow and the performance of the arcjet thruster for the cases with the hydrazine or hydrogen as the propellant. The integrated axial Lorentz force in the thruster nozzle is also calculated and compared with the thrust force of the arcjet thruster. It is found that the integrated axial Lorentz force is much smaller than the thrust force for the low-power arcjet thruster. Modeling results for the NASA 1-kW class arcjet thruster with simulated hydrazine as the propellant are found to be reasonably consistent with available experimental data.

Plume Parameters and Thruster Properties of a Low Power Arcjet

Abstract. A low power arcjet-thruster of 1 kW-class with gas mixture of H2-N2 or pure argon as the propellant is fired at a chamber pressure about 10 Pa. The nozzle temperature is detected with an infrared pyrometer; a plate set perpendicular to the plume axis and connected to a force sensor is used to measure the thrust; a probe with a tapered head is used for measuring the impact pressure in the plume flow; and a double-electrostatic probe system is applied to evaluate the electron temperature. Results indicate that the high nozzle temperature could adversely affect the conversion from enthalpy to kinetic energy. The plume flow deviates evidently from the LTE condition, and the rarefied-gas dynamic effect should be considered under the high temperature and low-pressure condition in analyzing the experimental phenomena.

Volt-ampere characteristics, nozzle temperature and thruster performances in a low power argon arcjet

Argon gas with simple atomic structure and favorite arcing stability at low input power was used as the propellant. The thruster with a regeneratively cooled nozzle were tested in a vacuum system capable of keeping the chamber pressure at about 10 Pa at a propellant feeding rate of 5 slm. Arc current, arc voltage, thrust, nozzle temperature and propellant feeding rate were measured in situ simultaneously. Effects of the working parameters such as the propellant feeding rate and arc current on the thruster performances, mainly the produced thrust, specific impulse and thrust efficiency, were examined. The variation of arc volt-ampere characteristics with running time and the effect of nozzle temperature on thruster property are discussed.

Development of arc root attachment in the nozzle of 1 kW N2 and H2-N2 arcjet thrusters

Arc root behavior affects the energy transfer and nozzle erosion in an arcjet thruster. To investigate the development of arc root attachment in 1 kW class N2 and H2-N2 arcjet thrusters from the time of ignition to the stably working condition, a kinetic series of end-on view images of the nozzle obtained by a high-speed video camera was analyzed. The addition of hydrogen leads to higher arc voltage levels and the determining factor for the mode of arc root attachment was found to be the nozzle temperature. At lower nozzle temperatures, constricted type attachment with unstable motions of the arc root was observed, while a fully diffused and stable arc root was observed at elevated nozzle temperatures.

氢-氮电弧加热推力器运行参数与性能

采用氢气和氮气的摩尔比r在1.0～2.0范围的混合气体作为推进剂,实时检测电弧加热推力器运行中的弧电流、弧电压、入口压力、真空室压力、质量流量和喷口温度等工作参数,研究了比功率、r和质量流量对推力器产生的推力、比冲和推力效率的影响。实验结果表明,同时增加混合气体的质量流量和r能有效提高推力器的推力;较高的r能获得高的比冲和效率,尤其是比冲随着r的提高明显地单调上升。

Modeling study on the flow, heat transfer and energy conversion characteristics of low-power arc-heated hydrogen/nitrogen thrusters

A modeling study is conducted to investigate the effect of hydrogen content in propellants on the plasma flow, heat transfer and energy conversion characteristics of low-power (kW class) arc-heated hydrogen/nitrogen thrusters (arcjets). 1:0 (pure hydrogen), 3:1 (to simulate decomposed ammonia), 2:1 (to simulate decomposed hydrazine) and 0:1 (pure nitrogen) hydrogen/nitrogen mixtures are chosen as the propellants. Both the gas flow region inside the thruster nozzle and the anode-nozzle wall are included in the computational domain in order to better treat the conjugate heat transfer between the gas flow region and the solid wall region. The axial variations of the enthalpy flux, kinetic energy flux, directed kinetic-energy flux, and momentum flux, all normalized to the mass flow rate of the propellant, are used to investigate the energy conversion process inside the thruster nozzle. The modeling results show that the values of the arc voltage, the gas axial-velocity at the thruster exit, and the specific impulse of the arcjet thruster all increase with increasing hydrogen content in the propellant, but the gas temperature at the nitrogen thruster exit is significantly higher than that for other three propellants. The flow, heat transfer, and energy conversion processes taking place in the thruster nozzle have some common features for all the four propellants. The propellant is heated mainly in the near-cathode and constrictor region, accompanied with a rapid increase of the enthalpy flux, and after achieving its maximum value, the enthalpy flux decreases appreciably due to the conversion of gas internal energy into its kinetic energy in the divergent segment of the thruster nozzle. The kinetic energy flux, directed kinetic energy flux and momentum flux also increase at first due to the arc heating and the thermodynamic expansion, assume their maximum inside the nozzle and then decrease gradually as the propellant flows toward the thruster exit. It is found that a large energy loss (31-52%) occurs in the thruster nozzle due to the heat transfer to the nozzle wall and too long nozzle is not necessary. Modeling results for the NASA 1-kW class arcjet thruster with hydrogen or decomposed hydrazine as the propellant are found to compare favorably with available experimental data.

Modeling study to compare the flow and heat transfer characteristics of low-power hydrogen, nitrogen and argon arc-heated thrusters

A modelling study is performed to compare the plasma °ow and heat transfer char- acteristics of low-power arc-heated thrusters (arcjets) for three di®erent propellants: hydrogen, nitrogen and argon. The all-speed SIMPLE algorithm is employed to solve the governing equa- tions, which take into account the e®ects of compressibility, Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. The temperature, veloc- ity and Mach number distributions calculated within the thruster nozzle obtained with di®erent propellant gases are compared for the same thruster structure, dimensions, inlet-gas stagnant pressure and arc currents. The temperature distributions in the solid region of the anode-nozzle wall are also given. It is found that the °ow and energy conversion processes in the thruster nozzle show many similar features for all three propellants. For example, the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appear- ing near the cathode tip; the °ow transition from the subsonic to supersonic regime occurs within the constrictor region; the highest axial velocity appears inside the nozzle; and most of the input propellant °ows towards the thruster exit through the cooler gas region near the anode-nozzle wall. However, since the properties of hydrogen, nitrogen and argon, especially their molecular weights, speci¯c enthalpies and thermal conductivities, are di®erent, there are appreciable di®er- ences in arcjet performance. For example, compared to the other two propellants, the hydrogen arcjet thruster shows a higher plasma temperature in the arc region, and higher axial velocity but lower temperature at the thruster exit. Correspondingly, the hydrogen arcjet thruster has the highest speci¯c impulse and arc voltage for the same inlet stagnant pressure and arc current. The predictions of the modelling are compared favourably with available experimental results.

低功率氩电弧加热发动机的数值模拟

采用可求解可压缩流动与传热的全速度SIMPLE算法, 对低功率氩电弧加热发动机内部的传热与流动进行了数值模拟, 获得了电弧加热发动机内的温度、速度、马赫数及流线分布. 计算结果表明: 电弧加热发动机内最高温度出现在阴极下游附近中心轴线处, 这是因为电弧在阴极表面收缩形成阴极弧点, 从而焦耳热成为该高温区的主要加热机制; 沿着发动机中心轴线, 气体温度和速度开始时随着距阴极距离的增加而迅速增加, 然后在等离子体流向喷管出口的过程中, 气体温度和速度逐渐下降. 此外还详细考察了弧电流变化对电弧加热发动机内部传热与流动特性的影响, 计算获得的发动机流量和比冲与实验结果基本一致.