Produção de etanol: uma opção para aproveitamento de resíduos gerados nas indústrias de reciclagem de papel.

2015

Aproveitamento de resíduos minerais na formulação de argamassas para a construção civil

Current environmental concerns include the excessive consumption and inefficient use of non-renewable natural resources. The construction industry is considered one of the largest consumers of natural raw materials, significantly contributing to the environmental degradation of the planet. The use of calcareous quarry (RPPC) and porcelain tile polishing residues (RPP) as partial replacements of the cement in mortars is an interesting alternative to minimize the exploration of considerably large amounts of natural resources. The present study aimed at investigating the properties of fresh and hardened mortars produced using residues to replace cement. The residues used were fully characterized to determine their specific mass, unitary mass, particle size distribution and morphology, and composition. The performance of the mortars was compared to that of reference compositions, prepared without residues. A total of 18 compositions were prepared, 16 using residues and 2 reference ones. The mortars were prepared using Portland CP II F 32 cement, CH I hydrated lime, river sand and tap water. The compositions of the mortars were 1:1:6 and 1:0.5:4.5 (vol%), and water to cement ratios of 1.87 and 1.45 were used, respectively. The mortars in the fresh state were evaluated by consistency index, water retention, density of mass and incorporated air content tests. In their hardened state, the mortars were evaluated by apparent mass density, modulus of elasticity, flexural tensile strength, compressive strength and water absorption by capillarity. The mortars were also analyzed by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and fluorescence. Finally, they were classified according to NBR 13281 standards. The mortars prepared using residues partially replacing the cement exhibited lower modulus of elasticity compared to the reference compositions, thus improving the performance in their intended use. On the downside, the water absorption by capillarity was affected by the presence of residues and both the tensile and compressive strength were reduced. However, from the overall standpoint, the replacement of cement by calcareous quarry or porcelain tile polishing residues did not result in significant changes in the properties of the mortars. Therefore, compositions containing these residues can be used in the construction industry

Aproveitamento de resíduos de cinza da cana de açúcar em massas cerâmicas

This study aimed to investigate the use of cane sugar ashes from small-scale stills of Eunápolis region, state of Bahia, in pottery mass that can be developed as porcelain stoneware. Bahia is the second largest producer of rum distillery in Brazil. In the production of rum is produced residue called bagasse, which is used to generate electricity in Power plants and in the distillery itself, generating ashes as residue, which is played in nature, causing environmental damage. We studied 5 (five) formulations of 0% 10% 20%, 30% and 40% by weight of the ash, without ignition and 3 (three) formulations of 10%, 20% and 30% with gray ash temperature of 1250ºC. The formulation at 0% by weight of ash was used for a comparison between the traditional mass of porcelain stoneware and the masses with the addition of ash calcined, replacing feldspar. The percentage by weight of kaolin and of Clay was kept the same, 30%, and all raw materials were derived from the state of Bahia. The samples were made in uniaxial array with dimensions of (60 x 20 x 5) mm and compressed to a pressure of 45 MPa. Assays were performed to characterize the raw by X-ray fluorescence, X-ray diffraction, ATD and ATG and Dilatometric analysis. The samples were sintered at temperatures of 1100°C, 1150°C, 1200°C and 1250°C, for the specimens with the ashes without ash and 1150° C and 1200° C for specimens with the gray level of calcined 60 minutes. and then we made a cooling ramp with the same rate of warming until reach ambient temperature. The sintered bodies were characterized by water absorption, porosity, linear shrinkage, bending strength and XRD of the fracture surface and the results analyzed. It was proven, after results of tests performed, that it is possible to use the ash residue of sugar cane bagasse on ceramic coating with the addition of up to 10% wt of the residue ash

Caracterização dos óleos de algumas sementes de frutas como aproveitamento de resíduos industriais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Procedimento híbrido envolvendo os métodos primal-dual de pontos interiores e branch and bound em problemas multiobjetivo de aproveitamento de resíduos de cana-de-açúcar

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização dos óleos extraídos de sementes de laranjas (Citrus sinensis) como aproveitamento de resíduos agroindustriais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aproveitamento dos resíduos de compósitos à base de resina poliéster e fibra de vidro

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Aplicações de secagem para o aproveitamento de resíduos da banana, visando sua aplicação na indústria

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento de resíduos de empresas moveleiras da região de São José do Rio Preto para confecção e avaliação de painéis aglomerados

Pós-graduação em Engenharia Civil - FEIS

Aproveitamento de resíduos de concreto na confecção de peças para pavimento intertravado de concreto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento de resíduos da indústria de celulose e papel em argamassa mista de revestimento interno

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento de resíduos florestais de Eucalyptus spp na indústria de fabricação de celulose para geração de energia térmica e elétrica

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Aproveitamento dos resíduos gerados pelo processamento industrial/artesanal de pedra-sabão da região de Ouro Preto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aproveitamento de resíduos de laminação da madeira para a produção de painel estrutural

Products derived from wood or engineered products are becoming interesting alternatives to the replacement of solid wood in various applications, from structural components to the furniture industry and packaging. Among these products, there are panels built by strands, particles and fibers, each one having their particular characteristics and potential of use. Since the different types of panels are produced, waste generation is part of the process, and that more technological it is, it still generates losses of raw materials. Based on the need for rational use of raw materials and using almost full of industrially processed wood, It arises the proposal of this work, which seeks to use waste from the lamination, like pieces of strands, broken strands, strands rough, cracked strands to produce panels with structural characteristics of the OSL panel (Oriented Strand Lumber), LSL (Laminated Strand Lumber) and OSB (Oriented Strand Lumber). Besides the use of waste, this paper seeks an alternative to the use of the adhesive, because the industry uses formaldehyde-based adhesives, which over the press, they emit large amounts of formaldehyde, which is very aggressive to humans and environment. The panels made with polyurethane resin based on castor oil and hot-pressed were characterized by physical and mechanical tests according to specifications of European Standard (EN). High values of tensile strength, elastic modulus and density were found in the results of tests. Adding to stable values of swelling and moisture content, the panel studied adds attractive features to the panel market, especially in the civil construction

Aproveitamento de resíduos na composição de painel sarrafeado amarrado: um estudo econômico

The manufacture of plywood panel already has about eighty years in Brazil. In general, plywood panels differ by their nature, composition and manufacturing; the most common MDF, OSB, particle and the joist. Some of these products can be generated fromindustrial waste, as the panelblockboard, you can use in their training waste destop boards (Battens), from industrial processes or processing of primary wood. This work aims to present the detailed study of the economic viability of utilization of industrial solid waste timber through the acquisition of a machine amarradeira of joists in a wood processing unit in city Itapeva-SP. We studied the application of wastein the composition of kernels blockboard panel tied its commercial acceptance and future prospects market. We noticed great economic advantage in investing in the study, compared with the transformation process of the joists in biomass energy, although the investment decision involves not only financial matters but also the acceptance market the product to be manufactured