Highly biocompatible and water-dispersible, amine functionalized magnetite nanoparticles, prepared by a low temperature, air-assisted polyol process: a new platform for bio-separation and diagnostics

A low temperature polyol process, based on glycolaldehyde mediated partial reduction of FeCl3 center dot 6H(2)O at 120 degrees C in the presence of sodium acetate as an alkali source and 2,2'-(ethylenedioxy)-bis-(ethylamine) as an electrostatic stabilizer has been used for the gram-scale preparation of biocompatible, water-dispersible, amine functionalized magnetite nanoparticles (MNPs) with an average diameter of 6 +/- 0.75 nm. With a reasonably high magnetization (37.8 e.m.u.) and amine groups on the outer surface of the nanoparticles, we demonstrated the magnetic separation and concentration implications of these ultrasmall particles in immunoassay. MRI studies indicated that these nanoparticles had the desired relaxivity for T-2 contrast enhancement in vivo. In vitro biocompatibility, cell uptake and MR imaging studies established that these nanoparticles were safe in clinical dosages and by virtue of their ultrasmall sizes and positively charged surfaces could be easily internalized by cancer cells. All these positive attributes make these functional nanoparticles a promising platform for further in vitro and in vivo evaluations.

Experimental studies on air-assisted impinging jet atomization

In the present study, a novel air-assisted impinging jet atomization is demonstrated. A configuration in which a gas jet is directed on to the impinging point of two liquid jets is used to improve the atomization. The effect of liquid properties such as viscosity and surface tension, angle between liquid jets and gas injection orifice diameter on spray characteristics has been experimentally studied. Backlit imaging and particle/droplet imaging and analysis techniques are utilized to characterize the sprays. The experimental results indicate that the effect of liquid viscosity is significant on the liquid sheet break up formed by the impinging jets. However, surface tension does not affect the spray structure significantly in this mode of atomization. At low liquid jet velocity, the prompt mode of atomization is observed where as atomization occurs in classical mode at higher liquid jet velocity. Results showed that variation in the angle between liquid jets do not affect the breakup phenomenon significantly. The spray angle is computed by finding the angle between the lines joining the impinging point and spray edge at an axial distance of 15 mm downstream of the impinging point from the ensemble-averaged data over 100 spray images. It was observed that effect of liquid jets impinging angle on the spray angle is higher at higher liquid velocity. Higher viscosity liquids exhibit lower spray angles. Droplet size measurements indicate a radial variation in the spray. An overall Sauter Mean Diameter (SMD) value is obtained by combining the droplet statistics at all radial locations at a fixed axial location. A very interesting trend is that the SMD is constant beyond a critical Gas to Liquid Ratio (GLR) and momentum ratio for a large variation in liquid viscosity and surface tension. This observation has important ramifications for fuel flexible systems. (C) 2013 Elsevier Ltd. All rights reserved.

EXPERIMENTAL STUDIES ON AIR-ASSISTED ATOMIZATION OF JATROPHA PURE PLANT OIL

The present study focuses on exploring air-assisted atomization strategies for effective atomization of high-viscosity biofuels, such as pure plant oils (PPOs). The first part of the study concerns application of a novel air-assisted impinging jet atomization for continuous spray applications, and the second part concerns transient spray applications. The particle/droplet imaging analysis (PDIA) technique along with direct imaging methods are used for the purpose of spray characterization. In the first part, effective atomization of Jatropha PPO is demonstrated at gas-to-liquid ratios (GLRs) on the order 0.1. The effect of liquid and gas flow rates on the spray characteristics is evaluated, and results indicate a Sauter mean diameter (SMD) of 50 mu m is achieved with GLRs as low as 0.05. In the second part of the study, a commercially available air-assisted transient atomizer is evaluated using Jatropha PPO. The effect of the pressure difference across the air injector and ambient gas pressure on liquid spray characteristics is studied. The results indicate that it is possible to achieve the same level of atomization of Jatropha as diesel fuel by operating the atomizer at a higher pressure difference. Specifically, a SMD of 44 mu m is obtained for the Jatropha oil using injection pressures of <1 MPa. A further interesting observation associated with this injector is the near constancy of a nondimensional spray penetration rate for the Jatropha oil spray.

Air-assisted growth of tin dioxide nanoribbons

SnO₂ nanoribbons have been synthesized by annealing of a milled SnO₂ powder, which is able to evaporate efficiently at the temperature as low as 1100 °C due to the metastable structure created by ball milling treatment. When the milled powder was annealed in an assembly of two combustion boats, SnO₂ nanoribbons formed on the surface of the milled powder. The nanoribbons tend to grow along the [101] crystallographic direction and their side surfaces are represented by ±(010) and ±(101) facets. The oxygen plays an important role in enhancing their formation.

Air-assisted boom sprayer and spray deposition on bean plants

A possibilidade do desenvolvimento de técnicas de aplicação de produtos fitossanitários mais seguras, com menores volumes de calda, número de aplicações e deriva, aliados à necessidade de se obter melhores níveis de controle dos agentes nocivos às plantas cultivadas, justificam o uso da assistência de ar junto à barra de pulverização. Com o objetivo de avaliar a deposição da pulverização na cultura do feijoeiro (Phaseolus vulgaris), em presença e ausência da assistência de ar junto à barra de pulverização, com diferentes pontas de pulverização e volumes de calda, foi conduzido um experimento em delineamento inteiramente casualizado, utilizando-se como traçador o óxido cuproso. Alvos artificiais (papel filtro com 3 x 3 cm) foram afixados nas superfícies adaxial e abaxial de folíolos posicionados nos terços superior e inferior de plantas, selecionadas ao acaso, distribuídas perpendicularmente ao deslocamento do pulverizador. Após a aplicação do traçador os coletores foram lavados individualmente em solução extratora de ácido nítrico a 1,0 mol L-1. A determinação quantitativa dos depósitos foi realizada com o uso da espectrofotometria de absorção atômica. A assistência de ar junto à barra de pulverização não aumentou a deposição do traçador em folíolos de feijoeiro, aos 48 dias após a emergência da cultura.

Effect of nozzle angle and air-jet parameters in air-assisted sprayer on biological effect of soybean asian rust chemical protection

Aiming at improving the efficiency control of Phakopsora pachyrhizi, this research evaluated different application techniques, using spray deposits and yield parameters of soybean crop. Two experiments were carried out in the experimental area of FCA/UNESP - Botucatu, SP, Brazil, in the soybean crop, Conquista variety, in the 2006/2007 season. The first experiment was arranged in random blocks with eight treatments and four replications. The treatments were conducted in factorial arrangement 4×2 (four air levels 0, 9, 11 and 29 km/h combined at two nozzle angles 0 and 30°) using AXI 110015 nozzles. Ten plants on each plot were selected for sampling spray deposits. Artificial targets were fixed on plants, two in the top and another two in the bottom part of plants (abaxial and adaxial leaf surface each one). For deposit evaluations, a cupric tracer was used and the amount of deposits was determined by a spectrophotometer. The second experiment was carried out in the same place and the treatments were of the same arrangement as the previous experiment, including control treatment (untreated plants). The spraying with triazole fungicide was realized in R2 and R5.2 growth stages of soybean with 142 l/ha spray volume. The nozzle angled of 30° combined with maximum air speed promoted the highest spray deposits on the soybean crop and influenced positively the control of the soybean Asian rust as well in the productivity of this crop.

Air flow humidification for air-assisted boom sprayer

The air-assisted ground spray is fairly widespread. However, due to the unpredictable weather conditions, the operational efficiency is impaired by stops on grounds of low humidity and high temperatures. The aim of this work was to assess an air humidification method and evaluate its impact on temperature and air humidity for the air curtain of the air-assisted sprayer. With respect to relative air humidity, it has increased in 6.59%, being the maximum change when inserting 1.92 L min-1. So, it is concluded that the pipeline humidification might significantly reduce temperature and enhance air humidity. The treatments performed in this study consisted of a varied flow of a humidity device, related to weather conditions. Temperature and relative air humidity were measured at 1.0 m height from right to left of middle point of the machine, corresponding to the end of the spray boom, in the middle and end of right spray boom. The readings were also performed at three different distances from the end of the pipeline and at 0.25 and 0.50 m from that to the soil. The results show that 0.48 L min-1 in the humidification system has promoted a better efficiency in reducing air-temperature, on average 2.52 ºC when compared to the non-humidified one.

Continuous combined microwave and hot air treatment of apples for fruit fly (Bactrocera tryoni and B. jarvisi) disinfestation

Apples at 24 ± 2 °C were heated in a pilot scale hot air assisted (40 °C) continuous pentagonal microwave system, to evaluate the effectiveness of this treatment on insect mortality (variety Mutsu) and fruit quality (variety Granny Smith). An average temperature of 53.4 ± 1.3 °C at core, bottom and flesh of the apple was recorded at the end of the treatment. One hundred percent mortality of the most tolerant stage of Queensland fruit fly (Bactrocera tryoni, Froggatt) and Jarvis's fruit fly (Bactrocera jarvisi, Tryon), were observed when the Mortality value (M52, equivalent time of isothermal treatment at 52 °C) at the slowest heating point applicable for each experiment was ≥ 50 min and ≥ 37 min, respectively. Results showed that microwave heat treatment is effective for insect disinfestation without any adverse impact on total soluble solids, flesh or peel firmness of the treated apples. The treated apples recorded a significantly higher pH and lower ion leakage than the untreated apples after 3 or 4 weeks. Therefore, the microwave heat treatment has the potential to be developed as an alternative chemical free quarantine treatment against economically significant insect pests. Industrial relevance Hot air assisted microwave heating of fruits and vegetables, is more cost effective compared to vapour heat treatment and ionising radiation for disinfestation of insects. Microwave treatment is environmentally friendly compared to fumigation and chemical treatments. Hot air assisted microwave disinfestation can be performed at farms or centralised pack houses since the capital cost would be comparatively lower than vapour heat or ionising radiation treatments.

Eficiência de diferentes ramais de pulverização e volumes de calda no controle de Brevipalpus phoenicis na cultura do café

Efficiency of different spraying lances and spraying volumes on the control of Brevipalpus phoenicis in coffee crops. The mite Brevipalpus phoenicis is found on coffee plantations in Brazil since the 1950's. Responsible for indirect losses due to its role as vector of a virus disease, this mite species often requires control measures, the most common based on mitecide spraying. It was evaluated the mortality of B. phoenicis due the coverage of spraying liquid applied on coffee plants, with two types of lances used in air assisted sprayers and four spraying. volumes. Treatments were applied with mitecide abamectin (Vertimec 18 CE (R) at 0.4 L per hectare), in volumes of 250, 400, 550 and 700 L per hectare, with two types of lances for the nozzles. The control efficiency against B. phoenicis, deposition and coverage by spray liquid on coffee plants was evaluated. Experimental delineation was in randomized blocks, with eight treatments plus a check plot in four replications. The statistical analysis was carried in a factorial scheme 2x4+1. No significant differences in the number of mites were found between treatments. As regards spraying liquid deposition, it was observed an increment with increasing spraying volumes, with the plant tops showing the best deposition of spraying liquid. The duplication of the lances (nozzle branches) resulted in a significant increase in control efficiency for B. phoenicis compared with conventional branch and with check plot, without dependence of spraying volume.

Velocidade do ar em barra de pulverização na deposição da calda fungicida, severidade da ferrugem asiática e produtividade da soja

O trabalho objetivou comparar a deposição da pulverização e o controle da ferrugem asiática após o tratamento com fungicidas sob quatro velocidades da assistência de ar junto à barra de pulverização na cultura da soja. Dois experimentos foram conduzidos na FCA/UNESP - Campus de Botucatu, safra 2006/07. Alvos artificiais foram fixados na superfície adaxial e abaxial de folíolos posicionados nas partes superior e inferior das plantas selecionadas e distribuídas perpendicularmente ao deslocamento do pulverizador. O oxicloreto de cobre (50% de cobre metálico) foi o marcador utilizado em pulverização e a determinação quantitativa dos depósitos feita com o uso de espectrofotometria de absorção atômica. Após a aplicação do fungicida piraclostrobina + epoxiconazole sob diferentes velocidades da assistência de ar junto à barra de pulverização (0, 9, 11 e 29 km h-1) procedeu-se a avaliação da severidade da doença e produtividade da soja. Na parte superior das plantas os maiores níveis de depósitos foram encontrados na pulverização sem assistência de ar. Já na parte inferior da planta foram encontrados os maiores níveis de deposição quando foram utilizadas as maiores velocidades da assistência de ar. No geral, a severidade da doença foi mais acentuada nos tratamentos sem o uso da assistência de ar. em relação à produtividade não houve diferenças entre os tratamentos com aplicação de fungicidas, porém houve incremento na produtividade para os tratamentos com assistência de ar.

Efeito da velocidade do ar em barra de pulverização na deposição de produtos fitossanitários em feijoeiro

Com o objetivo de avaliar o efeito da variação da velocidade do ar em barra de pulverização na deposição da calda na cultura do feijoeiro (Phaseolus vulgaris), realizou-se o experimento em 9 e 10 de outubro de 2000, no Centro de Pesquisas Agronômicas - Cyanamid, em Iracemápolis (SP), em delineamento inteiramente casualizado, aos 48 dias após a emergência (DAE). Para isso, convencionou-se que a rotação máxima do ventilador, medida com o auxílio de fototacômetro, possibilitou a obtenção da velocidade máxima do ar na barra de pulverização e, a partir daí, níveis de 50% e 75% da velocidade máxima do ar. Alvos artificiais foram fixados na superfície adaxial e na abaxial de folíolos posicionados, nos terços superior e inferior das plantas selecionadas, ao acaso, e distribuídas perpendicularmente ao deslocamento do pulverizador. O óxido cuproso (50% de cobre metálico) foi o traçador utilizado em pulverização e a determinação quantitativa dos depósitos feita com o uso da espectrofotometria de absorção atômica. Os resultados sugerem que a variação da velocidade do ar na barra pulverizadora não influenciou sobre os níveis de depósitos no feijoeiro, aos 48 DAE, nas condições do presente trabalho.

Deposição e perdas da calda em feijoeiro em aplicação com assistência de ar na barra pulverizadora

Com o objetivo de avaliar a influência da assistência de ar na deposição da calda de pulverização, em plantas de feijoeiro (Phaseolus vulgaris) aos 26 dias após a emergência (DAE), com pontas de pulverização de jato cônico vazio (JA-0,5 e JA-1) e jato plano (AXI-110015), e volumes de calda, foi realizado um experimento em delineamento inteiramente casualizado, utilizando como traçador o íon cobre. Alvos coletores (papel de filtro com 3 x 3 cm) foram afixados nas superfícies adaxial e abaxial de folíolos posicionados nas partes superior e inferior das plantas. Para aplicar a solução traçadora, utilizou-se pulverizador com barras de 14 metros, com e sem assistência de ar, volumes de 60 e 100 L.ha-1, e velocidade do ar correspondente a 50% da rotação máxima do ventilador. Após a aplicação, os coletores foram lavados individualmente em solução extratora de ácido nítrico a 1,0 mol.L-1, e a quantificação dos depósitos através de espectrofotometria. A assistência de ar não influenciou na deposição da calda tanto a 60 quanto a 100 L.ha-1. O maior volume proporcionou maiores depósitos, sendo constatadas elevadas perdas para o solo (mais de 60%).

Dessecação da aveia-preta (Avena strigosa Schreb) com herbicida de contato, em presença ou não de assistência de ar junto à barra do pulverizador, em diferentes volumes de calda

A tecnologia de aplicação dos produtos fitossanitários na agricultura pode ser aprimorada mediante a redução dos desperdícios. Com o objetivo de contribuir com tal avanço tecnológico, avaliou-se a eficácia de um herbicida com ação de contato, aplicado em pós-emergência com pulverizadores sem e com assistência de ar junto à barra, em diferentes volumes de calda. O experimento foi instalado no município de Ponta Grossa - PR, com a dessecação de aveia-preta (Avena strigosa Schreb) implantada em sistema de plantio direto sob a palha. Empregou-se a mistura herbicida formulada (SC) de dicloreto de paraquate (400 g ha-1) + diuron (200 g ha-1). O delineamento experimental utilizado foi o de blocos casualizados (DBC), em esquema fatorial 2 (pulverizador sem e com assistência de ar) x 5 (volumes de calda: 0; 100; 200; 300 e 400 L ha-1), com quatro repetições. A avaliação do efeito da dessecação se deu por meio da escala proposta pela Asociación Latinoamericana de Malezas (ALAM). A interação entre os fatores foi significativa, obtendo-se suficiência na dessecação a partir de 200 e 100 L ha-1, sem e com assistência de ar na barra, respectivamente.