Estudo de problemas de corrosão em cabos de aço zincado

As cablagens metálicas são aplicadas abundantemente na montagem dos automóveis, para accionamento de diversos dispositivos, tais como a abertura de portas, abertura da mala ou da tampa do motor, abertura do tampão do depósito de combustível, accionamento do travão de mão, etc. Nas cablagens metálicas utilizadas na indústria automóvel é comummente utilizado arame entrançado de aço zincado, o qual foi já estudado resistir à agressividade das condições em que habitualmente trabalham. No entanto, para que esta estabilidade de funcionamento exista, torna-se necessário que a qualidade do arame entrançado seja a mais adequada. O presente trabalho surgiu da necessidade de averiguar quais as razões que estariam por detrás do aparecimento de quantidades relativamente abundantes de Óxido de Zinco (ZnO) em cablagens metálicas utilizadas na indústria automóvel, poucas semanas depois do seu fabrico. O estudo foi levado a cabo com vista a satisfazer as necessidades de investigação deste problema por parte de uma empresa de cablagens metálicas instalada no nosso país, a FicoCables, estabelecendo quais as causas-raiz deste problema, com vista a poder evitálo no futuro. O trabalho foi concluído com sucesso, tendo-se averiguado que existiam lacunas graves de limpeza do cabo entre as operações de conformação do arame e de zincagem, com deposição de elementos potenciadores do Óxido de Zinco na interface, os quais viriam a revelar-se cruciais à posteriori, para a nucleação e desenvolvimento do Óxido de Zinco na superfície do cabo.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

Effects of hydrogen assisted stress corrosion on damage tolerance of a high-strength duplex stainless steel wire for prestressing concrete

The study brings new insights on the hydrogen assisted stress corrosion on damage tolerance of a high-strength duplex stainless steel wire which concerns its potential use as active reinforcement for concrete prestressing. The adopted procedure was to experimentally state the effect of hydrogen on the damage tolerance of cylindrical smooth and precracked wire specimens exposed to stress corrosion cracking using the aggressive medium of the standard test developed by FIP (International Prestressing Federation). Stress corrosion testing, mechanical fracture tests and scanning electron microscopy analysis allowed the damage assessment, and explain the synergy between mechanical loading and environment action on the failure sequence of the wire. In presence of previous damage, hydrogen affects the wire behavior in a qualitative sense, consistently to the fracture anisotropy attributable to cold drawing, but it does not produce quantitative changes since the steel fully preserves its damage tolerance.

Federal Trade Commission vs. United States Steel Corporation, American Bridge Company, American Sheet & Tin Plate Company, Carnegie Steel Company, American Steel & Wire Company, Illinois Steel Company, Minnesota Steel Company, Tennessee Coal, Iron and Railroad Compay [sic], et al., respondents. State of Illinois, state of Iowa, state of Minnesota and state of Wisconsin, amici curiæ. Statement of case, [vol. I-II]. H.G. Pickering, attorney for amici curiæ. ... K.E. Steinhauer, attorney for Commission. Cordenio A. Severance and William W. Corlett, attorneys for the respondents.

Paged continuously.

Iron and steel wire; a bibliography,

Mode of access: Internet.

Influence of pretreatment on corrosion behaviour of duplex zinc/polymer coatings on steel substrates

An investigation has been undertaken to determine the major factors influencing the corrosion resistance of duplex-zinc coatings on steel substrates.Premature failure of these systems has been attributed to the presence of defects such as craters and pinholes in the polymer film and debonding of the polymer film from the zinc substrate.Defects found on commercially produced samples have been carefully characterised using metallographic and scanning electron microscopy techniques. The influence of zinc substrate surface roughness, polymer film thickness and degassing of conversion coatings films on the incidence of defects has been determined.Pretreatments of the chromate, chromate-phosphate, non chromate, and alkali-oxide types were applied and the conversion coatings produced characterised with respect to their nature and composition. The effect of degassing on the properties of the films was also investigated. Electrochemical investigations were carried out to determine the effect of the presence of the eta or zeta phase as the outermost layer of the galvanized coating.Flow characteristics of polyester on zinc electroplated hot-dip continuous and batch galvanized and zinc sprayed samples were investigated using hot-stage microscopy. The effects of different pretreatments and degassing after conversion coating formation on flow characteristics were determined.Duplex coatings were subjected to the acetic acid salt spray test. The effect on adhesion was determined using an indentation debonding test and the results compared with those obtained using cross-cut/peel and pull-off tests. The locus of failure was determined using scanning electron microscopy and X-ray photoelectron spectroscopy techniques.

Residual stress influence on fatigue lifetimes of electroplated AISI 4340 high strength steel

Residual stresses play an important role in the fatigue lives of structural engineering components. In the case of near surface tensile residual stresses, the initiation and propagation phases of fatigue process are accelerated; on the other hand, compressive residual stresses close to the surface may increase fatigue life. In both decorative and functional applications, chromium electroplating results in excellent wear and corrosion resistance. However, it is well known that it reduces the fatigue strength of a component. This is due to high tensile internal stresses and microcrack density. Efforts to improve hard chromium properties have increased in recent years. In this study, the effect of a nickel layer sulphamate process, as simple layer and interlayer, on fatigue strength of hard chromium electroplated AISI 4340 steel hardness - HRc 53, was analysed. The analysis was performed by rotating bending fatigue tests on AISI 4340 steel specimens with the following experimental groups: base material, hard chromium electroplated, sulphamate nickel electroplated, sulphamate nickel interlayer on hard chromium electroplated and electroless nickel interlayer on hard chromium electroplated. Results showed a decrease in fatigue strength in coated specimens and that both nickel plating interlayers were responsible for the increase in fatigue life of AISI 4340 chromium electroplated steel. The shot peening pre-treatment was efficient in reducing fatigue loss in the alternatives studied.

One-dimensional zinc phosphates with linear chain structure

Three one-dimensional zinc phosphates, [C5N2H14][Zn(HPO4)2], I, [C10N4H26][Zn(HPO4)2].2H2O II, and [C4N2H6]2[Zn(HPO4)], III, have been prepared employing hydro/solvothermal methods in the presence of organic amines. While I and II consist of linear chains of corner-shared four-membered rings, III is a polymeric wire where the amine molecule is directly bonded to the metal center. The wire, as well as the chain in these structures, are held together by hydrogen bond interactions involving the amine and the framework oxygens. The polymeric zinc phosphate with wire-like architecture, III, is only the second example of such architecture. Crystal data: I, monoclinic, P21/c (no. 14), a=8.603(2), b=13.529(2), c=10.880(1) Å, β=94.9(1)°, V=1261.6(1) Å3, Z=4, ρcalc.=1.893 gcm−3, μ(MoKα)=2.234 mm−1, R1=0.032, wR2=0.086, [1532 observed reflections with I>2σ(I)], II, orthorhombic, Pbca (no. 61), a=8.393(1), b=15.286(1), c=22.659(1) Å, V=2906.9(2) Å3, Z=8, ρcalc.=1.794 gcm−3, μ(MoKα)=1.957 mm−1, R1=0.055, wR2=0.11, [1565 observed reflections with I>2σ(I) and III, monoclinic, P21/c (no. 14), a=8.241(1), b=13.750(2), c=10.572(1) Å, β=90.9(1)°, V=1197.7(2) Å3, Z=4, ρcalc.=1.805 gcm−3, μ(MoKα)=2.197 mm−1, R1=0.036, wR2=0.10, [1423 observed reflections with I>2σ(I)].

Torsion fracture behavior of drawn pearlitic steel wires with different heat treatments

In this paper, torsion fracture behavior of drawn pearlitic steel wires with different heat treatments was investigated. Samples with different heat treatments was investigated. Samples with different heat treatment conditions were subjected to torsion and tensile tests. The shear strain along the torsion sample after fracture was measured. Fracture surface of wires was examined by Scanning Electron Microscopy. In addition, the method of Differential Scanning Calorimetry was used to characterize the thermodynamic process in the heat treatment. A numerical simulation via finite element method on temperature field evolution for the wire during heat treatment process was performed. The results show that both strain aging and recovery process occur in the material within the temperature range between room temperature and 435 degrees C. It was shown that the ductility measured by the number of twists drops at short heating times and recovers after further heating in the lead bath of 435 degrees C. On the other hand, the strenght of the wire increases at short heating times and decreases after further heating. The microstructure inhomogeneity due to short period of heat treatment, coupled with the gradient characteristics of shear deformation during torsion results in localized shear deformation of the wire. In this situation, shear cracks nucleate between lamella and the wire breaks with low number of twists.

Import substitution of combination wire rope. Part 3: Comparison of standard Cift-CWR and imported combination wire rope

Tensile and extension properties of standard Cift-CWR and imported combination wire ropes from Japan, Norway and Denmark are studied and the analysis is presented in the paper. Tensile and chemical properties of steel wire, tensile and abrasive properties of PP covering, effect of twist on material at different stages are worked out and reported.

Photoelastic analysis of forces generated by T-loop springs made with stainless steel or titanium-molybdenum alloy

Introduction: The purpose of this study was to use photoelastic analysis to compare the system of forces generated by retraction T-loop springs made with stainless steel and titanium-molybdenum alloy (TMA) (Ormco, Glendora, Calif) with photoelastic analysis. Methods: Three photoelastic models were used to evaluate retraction T-loop springs with the same preactivations in 2 groups. In group 1, the loop was constructed with a stainless steel wire, and 2 helicoids were incorporated on top of the T-loop; in group 2, it was made with TMA and no helicoids. Results: Upon using the qualitative analysis of the fringe order in the photoelastic model, it was observed that the magnitude of force generated by the springs in group 1 was significantly higher than that in group 2. However, both had symmetry for the active and reactive units related to the system of force. Conclusions: Both springs had the same mechanical characteristics. TMA springs showed lower force levels. (Am J Orthod Dentofacial Orthop 2011;140:e123-e128)

Fracture micromechanisms and residual stresses of a highly resistant duplex stainless steel

The paper presents some preliminary results of an ongoing research intended to qualify a highly resistant duplex stainless steel wire as prestressing steel and, gets on insight on (he wires' fracture micromechanism and residual stresses field. SEM fractographic analysis of the stainless steel wires indicates an anisotropic fracture behavior in tension, in presence of surface flaws, attributed to the residual stresses generated through the fabrication process. The residual stresses magnitude influences the damage tolerance, its knowledge being a key issue in designating/qualifying the wires as prestressing steels.

Fracture micromechanisms and residual stresses of a highly resistant duplex stainless steel

The paper presents some preliminary results of an ongoing research intended to qualify a highly resistant duplex stainless steel wire as prestressing steel and, gets on insight on (he wires' fracture micromechanism and residual stresses field. SEM fractographic analysis of the stainless steel wires indicates an anisotropic fracture behavior in tension, in presence of surface flaws, attributed to the residual stresses generated through the fabrication process. The residual stresses magnitude influences the damage tolerance, its knowledge being a key issue in designating/qualifying the wires as prestressing steels.

Lubrication efficiency and die design in wire drawing

With the competitive challenge facing business today, the need to keep cost down and quality up is a matter of survival. One way in which wire manufacturers can meet this challenge is to possess a thorough understanding of deformation, friction and lubrication during the wire drawing process, and therefore to make good decisions regarding the selection and application of lubricants as well as the die design. Friction, lubrication and die design during wire drawing thus become the subject of this study. Although theoretical and experimental investigations have been being carried out ever since the establishment of wire drawing technology, many problems remain unsolved. It is therefore necessary to conduct further research on traditional and fundamental subjects such as the mechanics of deformation, friction, lubrication and die design in wire drawing. Drawing experiments were carried out on an existing bull-block under different cross-sectional area reductions, different speeds and different lubricants. The instrumentation to measure drawing load and drawing speed was set up and connected to the wire drawing machine, together with a data acquisition system. A die box connected to the existing die holder for using dry soap lubricant was designed and tested. The experimental results in terms of drawing stress vs percentage area reduction curves under different drawing conditions were analysed and compared. The effects on drawing stress of friction, lubrication, drawing speed and pressure die nozzle are discussed. In order to determine the flow stress of the material during deformation, tensile tests were performed on an Instron universal test machine, using the wires drawn under different area reductions. A polynomial function is used to correlate the flow stress of the material with the plastic strain, on which a general computer program has been written to find out the coefficients of the stress-strain function. The residual lubricant film on the steel wire after drawing was examined both radially and longitudinally using an SEM and optical microscope. The lubricant film on the drawn wire was clearly observed. Therefore, the micro-analysis by SEM provides a way of friction and lubrication assessment in wire drawing.

钢丝绳结构及工艺集成设计系统

针对钢丝绳实际生产需要,提出基于钢丝绳结构理论设计基础的结构与工艺集成设计系统框架,建立钢丝绳结构设计、性能分析及间隙计算的理论模型,并利用相关数据进行理论值与实际值分析,完成钢丝绳性能参数的敏感性分析模型和理论修正模型,为钢丝绳结构设计与工艺设计的并行处理提供了理论上的指导,最终实现钢丝绳的智能设计与制造