All-optical TDM to WDM signal conversion and partial regeneration using XPM with triangular pulses

We propose a new all-optical, all-fibre scheme for conversion of time-division multiplexed to wavelength-division multiplexed signals using cross-phase modulation with triangular pulses. Partial signal regeneration using this technique is also demonstrated.

Reduction of XPM penalty by sub-bit delay demodulation of DQPSK

We show that using a shortened delay in the demodulator for DQPSK channels can significantly reduce the XPM penalties caused by transmitting 40Gb/s DQPSK channels alongside 10Gb/s OOK channels. © 2010 Optical Society of America.

Reduction of XPM penalty by sub-bit delay demodulation of DQPSK

We show that using a shortened delay in the demodulator for DQPSK channels can significantly reduce the XPM penalties caused by transmitting 40Gb/s DQPSK channels alongside 10Gb/s OOK channels. © 2010 Optical Society of America.

All-optical TDM to WDM signal conversion and partial regeneration using XPM with triangular pulses

We propose a new all-optical, all-fibre scheme for conversion of time-division multiplexed to wavelength-division multiplexed signals using cross-phase modulation with triangular pulses. Partial signal regeneration using this technique is also demonstrated.

Influence of hardwood, softwoodand fractionated pulp in a stratifiedthree-layered fine paper : Lövved, barrved och fraktionerad massa ochdess inverkan på ett treskiktat finpapper

Four different trials of stratified three-layered fine paper, of sulphate pulp, were performed to investigate if stratified fine fraction or fibres from birch can improve the properties of a paper compared to a reference sheet. All trials had five different scenarios and each scenario was calendered with different linear load. All sheets had a grammage of 80 g/m2.In the first trial, the paper contained birch, pine and filler of calciumcarbonate (marble), and was manufactured with the pilot paper machine XPM and the stratified headbox Formator at RCF (Stora Enso Research Center in Falun). The furnish consisted of 75% birch and 25% pine.The second trial contained coated sheets with paper from trial one as the base paper. The coating slip contained calciumcarbonate and clay and the amount was approximately 10-12 g/m2.The third trial, also with birch and pine but without filler, was performed at STFI (Skogsindustrins Tekniska Forskningsinstitut in Stockholm) with the laboratory scaled paper machine StratEx and the stratified headbox AQ-vanes. The furnish consisted of 75% birch and 25% pine, except for one scenario which contained of 75% pine and 25% birch.The last trial contained fractionated pulp of birch and pine and was performed at STFI. 50% was fine fraction and 50% was coarse fraction.This test does not show any clear benefits of making stratified sheets of birch and pine when it comes to properties such as bending stiffness, tensile index and surface smoothness. The retention can be improved with birch in the surface plies. It is possible that the formation can be improved with birch in the surface plies and pine in the middle ply. It is also possible that fine fraction in the surface plies and coarse fraction in the middle ply can improve both surface smoothness and bending stiffness. The results in this test are shown with confidence intervals which points out the difficulties of analysing sheets manufactured with a pilot paper machine or a laboratory scaled paper machine.

Estratégia de projeto de atribuição de comprimento de onda com restrição de camada física em redes WDM

O sistema WDM (Wavelength Division Multiplexing) é considerado como uma tecnologia madura para ser usada no backbone de redes ópticas. Entretanto, encontrar uma solução ótima para o algoritmo de atribuição de comprimento de onda no projeto e operação destas redes, ainda é uma questão em aberto. A pesquisa realizada nesta tese aborda os principais aspectos relacionados ao processo de atribuição de comprimento de onda em sistemas WDM, e como resultado foi proposta uma metodologia que minimiza a degradação do sinal óptico gerada pela modulação de fase cruzada (XPM – Cross-Phase Modulation). Esta proposta é composta por uma metodologia híbrida baseada em Coloração de Grafo e Algoritmo Genético (AG), sendo que o primeiro tem a função de reduzir o número de comprimentos de onda necessários para atender a matriz de tráfego (que é fornecida a priori) e o último tem a função de encontrar a ordem de ativação de canais na grade de comprimentos de onda, com o objetivo de reduzir o efeito XPM. A proposta foi comparada com o algoritmo First-Fit em diferentes cenários e topologias de redes, e demonstrou uma considerável redução na probabilidade de bloqueio.

Wavelength assignment using a hybrid evolutionary computation to reduce cross-phase modulation

In this paper, we propose a hybrid methodology based on Graph-Coloring and Genetic Algorithm (GA) to solve the Wavelength Assignment (WA) problem in optical networks, impaired by physical layer effects. Our proposal was developed for a static scenario where the physical topology and traffic matrix are known a priori. First, we used fixed shortest-path routing to attend demand requests over the physical topology and the graph-coloring algorithm to minimize the number of necessary wavelengths. Then, we applied the genetic algorithm to solve WA. The GA finds the wavelength activation order on the wavelengths grid with the aim of reducing the Cross-Phase Modulation (XPM) effect; the variance due to the XPM was used as a function of fitness to evaluate the feasibility of the selected WA solution. Its performance is compared with the First-Fit algorithm in two different scenarios, and has shown a reduction in blocking probability up to 37.14% when considered both XPM and residual dispersion effects and up to 71.42% when only considered XPM effect. Moreover, it was possible to reduce by 57.14% the number of wavelengths.

Light curing through glass ceramics with a second- and a third-generation LED curing unit: effect of curing mode on the degree of conversion of dual-curing resin cements

Objectives The aim of this study was to measure the degree of conversion (DC) of five dual-curing resin cements after different curing modes with a second- and a third-generation light-emitting diode (LED) curing unit. Additionally, irradiance of both light curing units was measured at increasing distances and through discs of two glass ceramics for computer-aided design/manufacturing (CAD/CAM). Materials and methods Irradiance and spectra of the Elipar FreeLight 2 (Standard Mode (SM)) and of the VALO light curing unit (High Power Mode (HPM) and Xtra Power Mode (XPM)) were measured with a MARC radiometer. Irradiance was measured at increasing distances (control) and through discs (1.5 to 6 mm thickness) of IPS Empress CAD and IPS e.max CAD. DC of Panavia F2.0, RelyX Unicem 2 Automix, SpeedCEM, BisCem, and BeautiCem SA was measured with an attenuated total reflectance–Fourier transform infrared spectrometer when self-cured (negative control) or light cured in SM for 40 s, HPM for 32 s, or XPM for 18 s. Light curing was performed directly (positive control) or through discs of either 1.5- or 3-mm thickness of IPS Empress CAD or IPS e.max CAD. DC was analysed with Kruskal–Wallis tests followed by pairwise Wilcoxon rank sum tests (α = 0.05). Results Maximum irradiances were 1,545 mW/cm2 (SM), 2,179 mW/cm2 (HPM), and 4,156 mW/cm2 (XPM), and all irradiances decreased by >80 % through discs of 1.5 mm, ≥95 % through 3 mm, and up to >99 % through 6 mm. Generally, self-curing resulted in the lowest DC. For some cements, direct light curing did not result in higher DC compared to when light cured through ceramic discs. For other cements, light curing through ceramic discs of 3 mm generally reduced DC. Conclusions Light curing was favourable for dual-curing cements. Some cements were more susceptible to variations in curing mode than others. Clinical relevance When light curing a given cement, the higher irradiances of the third-generation LED curing unit resulted in similar DC compared to the second-generation one, though at shorter light curing times.

Estudio de limitaciones en sistemas WDM

Los avances tecnológicos de los últimos años han modificado el panorama de las comunicaciones ópticas. Los amplificadores EDFA (Erbium-Doped Fiber Amplifier) han alterado dos aspectos fundamentales de los sistemas WDM (Wavelength Division Multiplexing): el aumento considerable de las distancias de regeneración y además, la tecnología WDM es un medio más económico de incrementar la capacidad de los sistemas que la tecnología TDM (Time Division Multiplexing). Sin embargo, la implementación de sistemas WDM con grandes tramos sin regeneración de señal óptica trae consigo la aparición de nuevos problemas, entre los que se encuentran las no-linealidades en fibra óptica. Estas no-linealidades en fibras de sílice se pueden clasificar en dos categorías: dispersión estimulada (de Raman y de Brillouin) y efectos debidos al índice no lineal de refracción (automodulación y modulación cruzada de fase y mezcla de cuatro ondas). Este Proyecto Fin de Carrera pretende ser un estudio teórico que refleje el actual Estado del Arte de los principales efectos no-lineales que se producen en los sistemas WDM: dispersión estimulada de Raman (SRS, Stimulated Raman Scattering), dispersión estimulada de Brillouin (SBS,Stimulated Brilfouin Scattering), automodulación de fase (SPM, Self-Phase Modulation), modulación cruzada de fase (XPM, Cross-Phase Modulation) y mezcla de cuatro ondas (FWM, Four-Wave Mixing).

UWB doublet generation employing non-linear effects of a Semiconductor Optical Amplifier Mach-Zehnder inteferometer

In this article, a novel method to generate an ultra-wideband (UWB) doublet using the cross-phase modulation (XPM) effect is proposed and experimentally demonstrated. The main component of the submitted architecture is a SOA-Mach-Zehnder interferometer (MZI) pumped with a modulated Gaussian pulse. Maximum and minimum conversion points are analyzed through the systems transfer function in order to determinate the most effective operation stage. By tuning different values for the SOAs currents, it is possible to identify a conversion step in which the input pulse is enough large to saturate the SOAMZI, leading to the generation of a UWB doublet pulse.

UWB doublet generation in an integrated semiconductor optical amplifier Mach-Zehnder interferometer

In this paper, we propose and experimentally demonstrate a novel technique to generate ultrawideband (UWB) doublet pulses by exploiting the cross-phase modulation (XPM) in a semiconductor optical amplifier (SOA). The key component in the proposed system consists on an integrated SOA Mach-Zehnder interferometer (MZI) pumped with a Gaussian pulse modulated optical carrier. The transfer function of the nonlinear conversion process leads to the generation of UWB doublet pulses through the control of the biasing point of the SOA-MZI.

Numerical modelling of spectral, temporal and statistical properties of Raman fiber lasers

Efficient numerical modelling of the power, spectral and statistical properties of partially coherent quasi-CW Raman fiber laser radiation is presented. XPM between pump wave and generated Stokes wave is not important in the generation spectrum broadening and XPM term can be omitted in propagation equation what sufficiently speeds-up simulations. The time dynamics of Raman fiber laser (RFL) is stochastic exhibiting events several times more intense that the mean value on the ps timescale. However, the RFL has different statistical properties on different time scales. The probability density function of spectral power density is exponential for the generation modes located either in the spectrum centre or spectral wings while the phases are distributed uniformly. The pump wave preserves the initial Gaussian statistics during propagation in the laser cavity. Intense pulses in the pump wave are evolved under the SPM influence and are not disturbed by the dispersion. Contrarily, in the generated wave the dispersion plays a significant role that results in stochastic behavior. © 2012 Elsevier B.V. All rights reserved.