Field assessment of the resistance of timber products to termite (Isoptera) damage: Results can change with the amount of bait wood

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

Membrane treatment of wood preserving site groundwater by SBP Technologies, Inc.

Mode of access: Internet.

Pressure-treated wood.

"This Lake notes publication was prepared by Jason Navota of the Northeastern Illinois Planning Commission, Chicago, Illinois"--P. [4]

Preserving wood by brush, dip, and short-soak methods /

Includes bibliographical references (p. 48-50).

Effet des macrophytes aquatiques sur le traitement d’eau contaminée à l’ACC et au PCP

L’objectif principal de ce projet est d’évaluer le potentiel d’un système de marais filtrants combinés pour le traitement d’un lixiviat contaminé aux agents de préservations du bois - l’arséniate de cuivre chromaté (ACC) et le pentachlorophénol (PCP) - en portant une attention particulière au rôle des plantes. Pour ce faire, une expérience en pot faisant varier la concentration d’exposition de quatre espèces de macrophyte (Typha angustifolia, Phalaris arundinacea, Phragmites australis americanus et Phragmites australis australis) a été effectuée. Le suivi de quatre marais filtrants à écoulement horizontal sous-surfacique, plantés d’une des quatre espèces de macrophyte et d’un bassin planté de saules (Salix Miyabeana SX67) a également été réalisé. La résistance des plantes au milieu contaminé, la capacité de bioaccumulation des macrophytes et les efficacités de traitement des différents systèmes ont été analysés. Nos résultats montrent que la concentration d’exposition n’influence pas la capacité des plantes à croître en milieu contaminé. Par contre, il existe une relation dose-réponse entre la concentration d’exposition et la capacité de bioaccumulation des macrophytes. Les quatre marais pilotes ont tous des efficacités de traitements supérieures à 55% en 2013 et 82% en 2014 pour les contaminants à l’étude. Le bassin de saule a la capacité théorique d’évapotranspirer jusqu’à 1200 L par jour. De plus, ses efficacités de traitements sont supérieures à 59% pour tous les composés à l’étude. L’utilisation de marais filtrants pour le traitement d’un lixiviat contaminé aux agents de préservations du bois est donc une alternative intéressante aux méthodes de traitement conventionnel.

STUDIES OF FUNCTIONALIZED NANOPARTICLES FOR SMART SELF-ASSEMBLY AND AS CONTROLLED DRUG DELIVERY

This dissertation is related to the studies of functionalized nanoparticles for self-assembly and as controlled drug delivery system. The whole topic is composed of two parts. In the first part, the research was conducted to design and synthesize a new type of ionic peptide-functionalized copolymer conjugates for self-assembly into nanoparticle fibers and 3D scaffolds with the ability of multi-drug loading and governing the release rate of each drug for tissue engineering. The self-assembly study confirmed that such peptide-functionalized amphiphilic copolymers underwent different self-assembly behavior. The bigger nanoparticles were more easily assembled into nanoparticle fibers and 3D scaffolds with larger pore size, while the smaller nanoparticle underwent faster self-assembly to form more compact 3D scaffolds with smaller porosity but more stable structure. Controlled release studies confirmed the ability of governing simultaneous release of different model drugs with independent release rate from a same scaffold. Cytotoxicity tests showed that all synthesized peptides, copolymers and peptide-copolymer conjugates were biocompatible with SW-620 cell lines and NIH3T3 cell lines. This new type of self-assembled scaffolds combined the advantages of peptide nanofibers and versatile controlled release of polymeric nanoparticles to achieve simultaneous multi-drug loading and controlled release of each drug, uniform distribution and flexibility of hydrogel scaffolds. The investigations in second part were first to design and synthesize organic biocide-loaded nanoparticles for low-leaching wood preservation using a cost-effective one-pot method to synthesize amphiphilic chitosan-g-PMMA nanoparticles loading with ~25-28 wt.% of the fungicide tebuconazole with particle size of ~100 nm diameter by FESEM. FESEM analysis confirmed efficient penetration of nanoparticles throughout the treated wooden stake with dimension of 19 × 19 × 455 mm^3. Leaching studies showed that biocide introduced into sapwood via nanoparticles leached only ~9% compared with the amount leached from tebuconazole solution-treated control, while soil jar tests showed that the nanoparticle-treated wood blocks were effectively protected from biological decay tested against G. trabeum, a brown rot fungus. Copper oxide nanoparticles with and without polymer stabilizers were also investigated to use as inorganic wood preservatives to clarify the factor affecting copper leaching from treated wood. Copper oxide nanoparticles with uniform diameters of ~10 nm and ~50 nm were prepared, and the leachates from southern pine sapwood treated with these nanoparticles were analyzed. It was found by TEM and EDS analysis that significant numbers of nanoparticles leached from the treated wood. The 50 nm nanoparticles leached slightly less than a soluble copper salt control, but 10 nm nanoparticles leached substantially more than the control. The effect of polymer stabilizers on nanoparticle leaching was also investigated. Results showed that polymer stabilizers increased leaching. The trends showed that nanoparticle size was a major factor in copper leaching.

Potential for using through-boring to improve groundline treatment of Australian wood species: A preliminary study.

An aging electricity distribution system and reduced availability of naturally durable tropical hardwoods in Australia will combine in the next decade to produce a major shortage of poles. One approach to mitigating this shortage is to utilize lower durability species and improve the penetration of preservatives into the refractory heartwood by introducing additional pretreatment processes. A potential method for improving preservative penetration in the critical ground-line zone is through-boring. This process, in which holes are drilled through the pole perpendicular to the grain in the ground-line zone, is widely used in the western United States for treatment of Douglas-fir and may be Suitable for many Australian wood species. The potential for improving heartwood penetration in eucalypts with alkaline-copper-quaternary (ACQ) compound was assessed on heartwood specimens from four species (Eucalyptus cloeziana F.Muell., E. grandis W.Hill ex Maiden, E. obliqua L'Her. and E. pellita F.Muell.) and Lophostemon confertus (R.Br.) Peter G.Wilson & J.T.Wateril). Longitudinal ACQ penetration was extremely shallow in L. confertus and only slightly better in E. cloeziana. Longitudinal penetration was good in both E. obliqua and E. pellita, although there was some variation in treatment results with length of pressure period. The results suggest that through-boring might be a reasonable approach for achieving heartwood penetration in some Eucalyptus species, although further studies are required to assess additional treatment schedules and to determine the effects of the process oil flexural properties of the poles.

Particle number and mass emission factors from combustion of wood samples collected from Queensland forest

Knowledge of particle emission characteristics associated with forest fires and in general, biomass burning, is becoming increasingly important due to the impact of these emissions on human health. Of particular importance is developing a better understanding of the size distribution of particles generated from forest combustion under different environmental conditions, as well as provision of emission factors for different particle size ranges. This study was aimed at quantifying particle emission factors from four types of wood found in South East Queensland forests: Spotted Gum (Corymbia citriodora), Red Gum (Eucalypt tereticornis), Blood Gum (Eucalypt intermedia), and Iron bark (Eucalypt decorticans); under controlled laboratory conditions. The experimental set up included a modified commercial stove connected to a dilution system designed for the conditions of the study. Measurements of particle number size distribution and concentration resulting from the burning of woods with a relatively homogenous moisture content (in the range of 15 to 26 %) and for different rates of burning were performed using a TSI Scanning Mobility Particle Sizer (SMPS) in the size range from 10 to 600 nm and a TSI Dust Trak for PM2.5. The results of the study in terms of the relationship between particle number size distribution and different condition of burning for different species show that particle number emission factors and PM2.5 mass emission factors depend on the type of wood and the burning rate; fast burning or slow burning. The average particle number emission factors for fast burning conditions are in the range of 3.3 x 1015 to 5.7 x 1015 particles/kg, and for PM2.5 are in the range of 139 to 217 mg/kg.

Seeing the Wood for the Trees: A Critical Evaluation of Methods to Estimate the Parameters of Stochastic Differential Equations

Maximum-likelihood estimates of the parameters of stochastic differential equations are consistent and asymptotically efficient, but unfortunately difficult to obtain if a closed-form expression for the transitional probability density function of the process is not available. As a result, a large number of competing estimation procedures have been proposed. This article provides a critical evaluation of the various estimation techniques. Special attention is given to the ease of implementation and comparative performance of the procedures when estimating the parameters of the Cox–Ingersoll–Ross and Ornstein–Uhlenbeck equations respectively.

My mother is water, my father is wood

'my mother is water, my father is wood' was an installation comprised of two large cork discs mounted on the gallery floor and wall, overlaid with images of photographic and archival research evidence, and a turned wood sculptural object. It also included a short video work on a miniature screen embedded in the upright disc. The work explored the language of natural elements and the structure of genealogical research to discuss the Scandinavian history of Queensland and my own family. The work was selected by the directors of LEVEL ARI in Brisbane for inclusion in their 2011 exhibitions program.