Quality of wood and pulp from a clone of Eucalyptus grandis planted at three locations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Construction, extension and evaluation of the improved smoking kiln (Banda) in Kainji Lake area

Fish smoking, as a traditional occupation of fishermen and women in Kainji Lake Area (Nigeria) is done using simple traditional ovens called 'Banda', the fuel for the smoking being almost hundred percent dependent on wood. A simple modification was made to the traditional 'Banda' oven using a damper to prevent burning of the fish. A comparison of the improved and the traditional 'Banda' was made. The results indicate that fuel wood consumption was reduced 52 percent by using the improved 'Banda', which implied that 50 percent of fish processor's income could be saved through the adoption of this technology. The most important advantage of the improved kiln, fuel wood conservation, represents for fishers a problem of an economic importance. Whilst they are aware that it is becoming much more difficult to get the needed fuel wood, the children can still conveniently collect enough wood for both home use and processing activities. The cost of the components of the improved kiln, when compared with the traditional version may be considered quite significant, and hence the reluctance of the fish processors in constructing similar ones. Selected blacksmiths were trained to continue the fabrication of the kiln component. The training was carried out to assure that the improved kiln will be constructed even after the project will end to support the fabrication

Resource use pattern and agroecosystem functioning in Rawanganga micro-watershed in Garhwal Himalaya, India

Agro-ecological resource use pattern in a traditional hill agricultural watershed in Garhwal Himalaya was analysed along an altitudinal transect. Thirty one food crops were found, although only 0.5% agriculture land is under irrigation in the area. Fifteen different tree species within agroforestry systems were located and their density varied from 30-90 trees/ha. Grain yield, fodder from agroforest trees and crop residue were observed to be highest between 1200 and 1600 m a.s.l. Also the annual energy input- output ratio per hectare was highest between 1200 and 1600 m a.s.l. (1.46). This higher input- output ratio between 1200-1600 m a.s.l. was attributed to the fact that green fodder, obtained from agroforestry trees, was considered as farm produce. The energy budget across altitudinal zones revealed 95% contribution of the farmyard manure and the maximum output was in terms of either crop residue (35%) or fodder (55%) from the agroforestry component. Presently on average 23%, 29% and 41% cattle were dependent on stall feeding in villages located at higher, lower and middle altitudes respectively. Similarly, fuel wood consumption was greatly influenced by altitude and family size. The efficiency and sustainability of the hill agroecosystem can be restored by strengthening of the agroforestry component. The approach will be appreciated by the local communities and will readily find their acceptance and can ensure their effective participation in the programme.

Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace

Foraging activity and demographic patterns of two termite species (Isoptera: Rhinotermitidae) living in urban landscapes in southeastern Brazil

Coptotermes gestroi and Heterotermes tenuis (Isoptera: Rbinotermitidae) are important pests in southeastern Brazil causing serious economic damage. In this study we determined the demographic patterns and foraging activity of these species using mark-release-recapture and the consumption of wooden stakes. Using both the weighted mean and Lincoln index methods, population estimates ranged from ≈ 0.57 to 1.99 million individuals for C. gestroi and from ≈ 0.20 to 1.37 million for H. tenuis. Territory size of the colonies ranged from 172.5 to 5235 m 2 for C. gestroi and from 16 to 40 m 2 for H. tenuis. Our results also indicate that foraging activity was dependent on the minimum temperature; however, the existence of a compensation strategy in the foraging activities may permit foragers to exploit food sources under different environmental conditions.

Avaliação da qualidade de mourões de várias espécies de Eucalyptus spp. tratados pelo método de substituição de seiva

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Análise experimental de vigas pré-formadas de concreto armado à flexão e ao cisalhamento

Vigas pré-formadas de concreto armado são elementos estruturais que apresentam fina camada superficial de concreto pré-moldado que define as suas formas geométricas. Esta camada superficial trabalha como forma que fica incorporada à viga após o lançamento do concreto moldado in loco, que consolidará a estrutura. Este sistema construtivo apresenta vantagem em relação ao sistema construtivo convencional por reduzir o consumo de madeira com formas e escoramento, e também em relação ao sistema pré-moldado por reduzir o custo de transporte e montagem da estrutura. Os elementos pré-formados apresentam menor peso em relação aos elementos pré-moldados, por apresentarem a seção parcialmente pré-moldada. Outra vantagem do sistema pré-formado em relação ao pré-moldado é a possibilidade de se obter maior rigidez nas ligações das vigas com o restante da estrutura com a colocação de armadura de engastamento ancorada no concreto moldado in loco. Este trabalho tem como objetivo analisar experimentalmente o comportamento das vigas pré-formadas à flexão e ao cisalhamento, através de ensaios de 9 vigas pré-formadas e 3 vigas maciças de referência. As vigas têm largura de 105 mm, altura de 340 mm e 2.500 mm de comprimento. Os resultados obtidos nos ensaios experimentais são comparados aos valores fornecidos pelas normas técnicas brasileiras e as principais normas internacionais. São apresentados e analisados os resultados observados para os deslocamentos verticais das vigas, deformações da armadura de flexão e da armadura de cisalhamento, deformações do concreto nas regiões de compressão e mapas de fissuração.

Foraging in subterranean termites (Isoptera: Rhinotermitidae): how do Heterotermes tenuis and Coptotermes gestroi behave when they locate equivalent food resources?

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo das madeiras de cecropia palmata (imbaúba) e eucalyptus grandis para produção de celulose e papel

Pós-graduação em Ciência Florestal - FCA

Forest products ...

In 10 nos. each year, 1907-1909; in 9 nos. each year, 1910-1911: 1. Pulp wood consumption. 2. Lumber, lath and shingles. 3. Slack cooperage stock. 4. Tanbark and tanning extracts. 5. Veneers. 6. Tight cooperage stock. 7. Wood distillation. 8. Cross-ties purchased. 9. Poles purchased. 10. Forest products of the United States.

Polyethism and comparability of termite choice assays in a model system using Microcerotermes turneri (Termitidae : Termitinae): Implications for standardised testing techniques

Traditional measures of termite food preference assess consequences of foraging behavior such as wood consumption, aggregation and/or termite survivorship. Although studies have been done to investigate the specifics of foraging behavior this is not generally integrated into choice assay experiments. Here choice assays were conducted with small isolated (orphaned) groups of workers and compared with choice assays involving foragers from whole nests (non-orphaned) in the laboratory. Aggregation to two different wood types was used as a measure of preference. Specific worker caste and instars participating in initial exploration were compared between assay methods, with samples of termites taken from nest carton material and sites where termites were feeding. Aggregation results differ between choice assay techniques. Castes and instars responsible for initial exploration, as determined in whole nest trials, were not commonly found exploring in isolated group trials, nor were they numerous in termites taken from active feeding sites. Consequently the use of small groups of M. turneri worker termites extracted from active feeding sites may not be appropriate for use in choice assays.

Variation in tracheid cross-sectional dimensions and wood viscoelasticity extent and control methods

Printing papers have been the main product of the Finnish paper industry. To improve properties and economy of printing papers, controlling of tracheid cross-sectional dimensions and wood viscoelasticity are examined in this study. Controlling is understood as any procedure which yields raw material classes with distinct properties and small internal variation. Tracheid cross-sectional dimensions, i.e., cell wall thickness and radial and tangential diameters can be controlled with methods such as sorting wood into pulpwood and sawmill chips, sorting of logs according to tree social status and fractionation of fibres. These control methods were analysed in this study with simulations, which were based on measured tracheid cross-sectional dimensions. A SilviScan device was used to measure the data set from five Norway spruce (Picea abies) and five Scots pine (Pinus sylvestris) trunks. The simulation results indicate that the sawmill chips and top pulpwood assortments have quite similar cross-sectional dimensions. Norway spruce and Scots pine are on average also relatively similar in their cross-sectional dimensions. The distributions of these species are somewhat different, but from a practical point of view, the differences are probably of minor importance. The controlling of tracheid cross-sectional dimensions can be done most efficiently with methods that can separate fibres into earlywood and latewood. Sorting of logs or partitioning of logs into juvenile and mature wood were markedly less efficient control methods than fractionation of fibres. Wood viscoelasticity affects energy consumption in mechanical pulping, and is thus an interesting control target when improving energy efficiency of the process. A literature study was made to evaluate the possibility of using viscoelasticity in controlling. The study indicates that there is considerable variation in viscoelastic properties within tree species, but unfortunately, the viscoelastic properties of important raw material lots such as top pulpwood or sawmill chips are not known. Viscoelastic properties of wood depend mainly on lignin, but also on microfibrillar angle, width of cellulose crystals and tracheid cross-sectional dimensions.

Wood and fiber properties of Norway spruce and its suitability for thermomechanical pulping.

In the first part of the study, the selected wood and fiber properties were investigated in terms of their occurrence and variation in wood, as well as their relevance from the perspective of thermomechanical pulping process and related end-products. It was concluded that the most important factors were the fiber dimensions, juvenile wood content, and in some cases, the content of heartwood being associated with extremely dry wood with low permeability in spruce. With respect to the above properties, the following three pulpwood assortments of which pulping potential was assumed to vary were formed: wood from regeneration cuttings, first-thinnings wood, and sawmill chips. In the experimental part of the study the average wood and fiber characteristics and their variation were determined for each raw material group prior to pulping. Subsequently, each assortment - equaling about 1500 m3 roundwood - was pulped separately for a 24 h period, at constant process conditions. The properties of obtained newsgrade thermomechanical pulps were then determined. Thermomechanical pulping (TMP) from sawmill chips had the highest proportion of long fibers, smallest proportion of fines, and had generally the coarsest and longest fibers. TMP from first-thinnings wood was just the opposite, whereas that from regeneration cuttings fell in between the above two extremes. High proportion of dry heartwood in wood originating from regeneration cuttings produced a slightly elevated shives content. However, no differences were found in pulp specific energy consumption. The obtained pulp tear index was clearly best in TMP made from sawmill chips and poorest in pulp from first-thinnings wood, which had generally inferior strength properties. No dramatical differences in any of the strength properties were found between pulp from sawmill residual wood and regeneration cuttings. Pulp optical properties were superior in TMP from first-thinnings. Unexpectedly, no noticeable differences, which could be explained with fiber morphology, were found in sheet density, bulk, air permeance or roughness between the three pulps. The most important wood quality factors in this study were the fiber length, fiber cross-sectional dimensions and percentage juvenile wood. Differences found in the quality of TMP manufactured from the above spruce assortments suggest that they could be segregated and pulped separately to obtain specific product characteristics, i.e., for instance tailor-made end-products, and to minimize unnecessary variation in the raw material quality, and hence, pulp quality.

Consumption of fa cai Nostoc soup: A Potential for BMAA exposure from Nostoc cyanobacteria in China?

Grown in arid regions of western China the cyanobacterium Nostoc flagelliforme - called fa cai in Mandarin and fat choy in Cantonese - is wild-harvested and used to make soup consumed during New Year's celebrations. High prices, up to $125 USD/kg, led to overharvesting in Inner Mongolia, Ningxia, Gansu, Qinghai, and Xinjiang. Degradation of arid ecosystems, desertification, and conflicts between Nostoc harvesters and Mongol herdsman concerned the Chinese environmental authorities, leading to a government ban of Nostoc commerce. This ban stimulated increased marketing of a substitute made from starch. We analysed samples purchased throughout China as well as in Chinese markets in the United States and the United Kingdom. Some were counterfeits consisting of dyed starch noodles. A few samples from California contained Nostoc flagelliforme but were adulterated with starch noodles. Other samples, including those from the United Kingdom, consisted of pure Nostoc flagelliforme. A recent survey of markets in Cheng Du showed no real Nostoc flagelliforme to be marketed. Real and artificial fa cai differ in the presence of beta-N-methylamino-L-alanine (BMAA). Given its status as a high-priced luxury food, the government ban on collection and marketing, and the replacement of real fa cai with starch substitutes consumed only on special occasions, it is anticipated that dietary exposure to BMAA from fa cai will be reduced in the future in China.

Wood : from the forest to the consumer

Illegal logging causes a number of environmental and social damages in countries where wood is sourced from native forests. Logging in protected areas is an act of irresponsibility that exacerbates the loss of biodiversity. In addition, uncontrolled deforestation and bushfires may aggravate climate change, not to mention the negative effects they impose on local populations, such as the impoverishment of rural communities whose livelihoods depend on forest products. Several studies show that Brazil ranks high in terms of irresponsible use of natural resources, including native wood from the Amazon. Even more worrisome is the fact that the state, despite being responsible for regulating logging activities, is one of the largest consumers of native wood, which subverts the goals of any government committed to sustainable environmental management. By monitoring the development and impacts of illegal timber production and consumption around the world, the Friends of the Amazon Network – an initiative by the Getulio Vargas Foundation with support from the British Government and the European Commission – identified a need to describe and evaluate, in a brief and instructive manner, the different mechanisms the state has available to reverse this predatory practice. One of the aspects discussed in this book is the role of civil servants in major efforts aimed at repressing illegal logging and timber production, as well as identifying products derived from these activities in order to prevent their consumption. This is the purpose of this publication, which uses detailed infographics and a journalistic approach, including interviews and true stories, to outline the complexity of Amazon timber’s chain of custody – from logging, processing and transportation to commercialization in the Brazilian market.