USE OF ADDITIVES IN THE WOOD BIODEGRADATION BY THE FUNGUS Ceriporiopsis subvermispora: EFFECT IN THE MANGANESE PEROXIDASE-DEPENDENT LIPID PEROXIDATION

USE OF ADDITIVES IN THE WOOD BIODEGRADATION BY THE FUNGUS Ceriporiopsis subvermispora: EFFECT IN THE MANGANESE PEROXIDASE-DEPENDENT LIPID PEROXIDATION. Ceriporiopsis subvermispora is a selective fungus in the wood delignification and the most promising in biopulping. Through the lipid peroxidation initiated by manganese peroxidase (MnP), free radicals can be generated, which can act in the degradation of lignin nonphenolic structures. This work evaluated the prooxidant activity (based in lipid peroxidation) of enzymatic extracts from wood biodegradation by this fungus in cultures containing exogenous calcium, oxalic acid or soybean oil. It was observed that MnP significant activity is required to promote lipid peroxidation and wood delignification. Positive correlation between prooxidant activity x MnP was observed up to 300 IU kg(-1) of wood.

Application of X-ray technique in nondestructive evaluation of eucalypt wood

X-rays were initially used for the inspection of special-purpose wood pieces for quantitative evaluation properties of different species. X-ray densitometry has had its use expanded ill dendroclimatology of Picea engelmannii trees. Subsequent laboratories developed applications of X-ray densitometry for environmental, wood science and technology, and related areas. This paper describes the basic methodology of X-ray densitometry applied to the eucalypt wood analysis, as well its presenting the results of applications in three areas: (i) evaluation of wood biodegradation by white rot fungi, (ii) detection of sapwood and heartwood, and (iii) determination of the effect of management oil wood properties. The wood decayed by white rot fungi was detected by X-ray densitometry with it decreasing wood density due to the biodegradation of cell wall components. The sapwood and heartwood of eucalypts were separated in response to the attenuation of X-rays, reflected by the wood anatomical structure and chemical composition. Also, Ill eucalypt trees after the application of irrigation and i characteristic wood density profiles were detected. Ill addition, the significant potential of X-ray densitometry for eucalypt wood research and analysis is discussed.

Effect of aqueous extracts from Ceriporiopsis subvermispora-biotreated wood on the decolorization of Azure B by Fenton-like reactions

Aqueous extracts from wood biotreated with the white-rot fungus Ceriporiopsis subvermispora were evaluated for their Fe3+- and Cu2+-reducing activities and their anti- or prooxidant properties in Fenton-like reactions to decolorize the recalcitrant dye Azure B. The decolorization of Azure B was strongly inhibited in the presence of 10% (v/v) wood extracts. Only 0.1% (v/v)-diluted extracts provided some enhancement of the Azure B decolorization. The iron-containing reactions decolorized more Azure B and consumed substantially more H2O2 than the reactions containing copper. This study demonstrates that water-soluble wood phenols exert anti- or prooxidant effects that depend on their concentration in the reactions and on the type of cation, Fe3+ or Cu2+, used to convert H2O2 to OH radicals. Crown Copyright (C) 2012 Published by Elsevier Ltd. All rights reserved.

Surfactant degradation by a catechol-driven Fenton reaction

The addition of 0.5 mM catechol is shown to accelerate the degradation and mineralization of the anionic surfactant DOWFaX (TM) 2A1 (sodium dodecyldiphenyloxide disulfonate) under conventional Fenton reaction conditions (Fe(II) plus H(2)O(2) at pH 3). The catalytic effect causes a 3-fold increase in the initial rate (up to ca. 20 min) of conversion of the surfactant to oxidation products (apparent first-order rate constants of 0.021 and 0.061 min(-1) in the absence and presence of catechol, respectively). Although this catalytic rate increase persists for a certain amount of time after complete disappearance of catechol itself (ca. 8 min), the reaction rate begins to decline slowly after the initial 20 min towards that observed in the absence of added catechol. Total organic carbon (TOC) measurements of net mineralization and cyclic voltammetric and high performance liquid chromatographic (HPLC) measurements of the initial rate of reaction of catechol and the surfactant provide insight into the role of catechol in promoting the degradation of the surfactant and of degradation products as the eventual inhibitors of the Fenton reaction. (C) 2010 Elsevier B.V. All rights reserved.

Desenvolvimentos da biopolpação no Brasil

Biopulping is a technology which application can be advantageous to mechanical or chemical pulping. It presents benefits such as the creation of stronger pulp, as well as energy or chemicals savings. This paper gives an overview of the recent efforts to develop biopulping processes in Brazil as well as provides critical information on biopulping development worldwide. Eucalyptus grandis wood chips have been biotreated by Ceriporiopsis subvermispora in a 50-ton biopulping pilot-plant and used to produce TMP and CTMP pulps on a mill scale, Up to 18% and 27% energy savings have been observed for producing 450-470 CSFreeness TMP and CTMP pulps. Despite darker bio-TMP pulps are produced, one-stage bleaching with 5% H2O2 was sufficient to improve brightness values to 70% and 72% for bio-TMP and control pulps, respectively. Understanding biopulping mechanisms is also relevant because more resistant and competitive fungal species could be selected with basis on a function-directed screen-ing project. As far as the chemical changes induced by the fungus in wood are concerned, recent efforts have pointed out for two different types of wood transformations. One of them involves intense lignin depolymerization in short biotreatment periods, while the other indicates that esterification reactions of oxalate secreted by the Jungas on the polysaccharides chains increase the water saturation point of the fibers. Both transformations are expected to affect the fiber-fiber bonding and, consequently, the physical resistance of wood.

Effects of exogenous calcium or oxalic acid on Pinus taeda treatment with the white-rot fungus Ceriporiopsis subvermispora

Pinus taeda wood chips were treated with the biopulping fungus Ceriporiopsis subvermispora in calcium-or oxalic acid-amended cultures. The secretion of hydrolytic and oxidative enzymes was inhibited only in the cultures having the highest concentration of calcium (1400 mg kg(-1) wood). Calcium decreased the availability of free oxalic acid, inhibited fungal growth, and reduced lignin mineralization and transformations. Oxalic acid amendment in the cultures was found not to affect the lignin mineralization and transformations; however, it did inhibit the depolymerization reactions detectable in the residual lignin that was retained in the biotreated wood. C. subvermispora presented catabolic activity for oxalic acid in the cultures amended with 1660 mg acid kg(-1) wood, whereas oxalic acid was synthesized when it was amended at low amounts or initially absent in the cultures. These data suggest one ideal ratio of oxalic acid in C. subvermispora cultures and indicate that its exogenous addition does not necessarily accompany the further degradation of lignin. Crown Copyright (C) 2012 Published by Elsevier Ltd. All rights reserved.

Uso de aditivos na biodegradação de madeira pelo fungo Ceriporiopsis subvermispora: efeito na peroxidação de lipídios dependente de manganês-peroxidase

Ceriporiopsis subvermispora is a selective fungus in the wood delignification and the most promising in biopulping. Through the lipid peroxidation initiated by manganese peroxidase (MnP), free radicals can be generated, which can act in the degradation of lignin nonphenolic structures. This work evaluated the prooxidant activity (based in lipid peroxidation) of enzymatic extracts from wood biodegradation by this fungus in cultures containing exogenous calcium, oxalic acid or soybean oil. It was observed that MnP significant activity is required to promote lipid peroxidation and wood delignification. Positive correlation between prooxidant activity x MnP was observed up to 300 IU kg-1 of wood.

Biodegradation of eucalyptus urograndis wood by fungi

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Improved termite resistance of wood by wax impregnation.

We investigated the effect of wax-treated and biocide-free wood specimens against three different termite species. A laboratory no-choice test with Reticulitermes banyulensis Clément was carried out in Valencia (Spain) under Mediterranean conditions for eight weeks. Scots pine sapwood (Pinus sylvestris L.) fully impregnated with distinct waxes was used. Two field trials were conducted with Coptotermes acinaciformis (Froggatt) and Mastotermes darwiniensis Froggatt in northern Queensland (Australia) with wax-impregnated beech (Fagus sylvatica L.) for 16 weeks. All three subterranean termites are of major economic importance in their respective regions. The results indicated that feeding pressure by the termites was sufficient within all trials for a valid test. Wax-impregnated Scots pine sapwood was classified as durable. No termites survived the test. The results showed an aging process under submersion conditions, which lead to a classification of moderately durable. The paraffin treatment showed good termite resistance under both test procedures, and was classified as durable. The Australian field trials showed a decreased mass loss of wax-treated beech, in which an amide wax showed excellent termite resistance. The results indicate a clear dependence of the termite resistance on the type and ratio of wax used and the feeding preferences of the specific termite species.

Improvement of termite resistance, dimensional stability and mechanical properties of pine wood by paraffin impregnation

Paraffin has been used as surface protection of wood throughout the ages but its use for impregnation to improve wood resistance to biodegradation is recent. This study determined the main improvements on wood properties with paraffin impregnation. Healthy Pinus pinaster Ait. wood was impregnated with paraffin at different levels using a hot–cold process. Weight gain, equilibrium moisture content and dimensional stability (ASE) at 35 and 65 % relative humidity, termite durability against Reticulitermes grassei (Clément), bending strength, bending stiffness (MOE) and Janka hardness were determined. Density increased from 0.57 to 0.99, ASE ranged between 38–96 % and 16–71 % for 35 and 65 % relative humidity, respectively. Equilibrium moisture content decreased from 9.9 and 12.0 % to 0.8 and 3.6 % for 35 and 65 % relative humidity. Termite durability improved from level 4 to level 3 of attack, and higher termite mortality was found in treated wood (52 % against 17 %). Bending strength (MOR) increased with paraffin weight gain, reaching a 39 % increase. MOE also increased by about 13 % for wood with a weight gain around 80 %. Janka hardness increased significantly reaching about 40 % for wood with 80 % weight gain. Paraffin impregnated wood has improved properties with regard to equilibrium moisture content, dimensional stability and density, bending strength and Janka hardness, and resistance against termites.

Particle number and mass emission factors from combustion of wood samples collected from Queensland forest

Knowledge of particle emission characteristics associated with forest fires and in general, biomass burning, is becoming increasingly important due to the impact of these emissions on human health. Of particular importance is developing a better understanding of the size distribution of particles generated from forest combustion under different environmental conditions, as well as provision of emission factors for different particle size ranges. This study was aimed at quantifying particle emission factors from four types of wood found in South East Queensland forests: Spotted Gum (Corymbia citriodora), Red Gum (Eucalypt tereticornis), Blood Gum (Eucalypt intermedia), and Iron bark (Eucalypt decorticans); under controlled laboratory conditions. The experimental set up included a modified commercial stove connected to a dilution system designed for the conditions of the study. Measurements of particle number size distribution and concentration resulting from the burning of woods with a relatively homogenous moisture content (in the range of 15 to 26 %) and for different rates of burning were performed using a TSI Scanning Mobility Particle Sizer (SMPS) in the size range from 10 to 600 nm and a TSI Dust Trak for PM2.5. The results of the study in terms of the relationship between particle number size distribution and different condition of burning for different species show that particle number emission factors and PM2.5 mass emission factors depend on the type of wood and the burning rate; fast burning or slow burning. The average particle number emission factors for fast burning conditions are in the range of 3.3 x 1015 to 5.7 x 1015 particles/kg, and for PM2.5 are in the range of 139 to 217 mg/kg.