Chromated Copper Arsenate (CCA) Treatment for Rubber Wood Preservation and its Impact on the Aquatic Biota

Faculty of Marine Sciences, Cochin University of Science and Technology

Material for lantern slides on wood preservation /

The plates are accompanied by a covering letter (6 l. at beginning) dated Oct. 11, 1919, from the compiler to Professor E.E. King of the University of Illinois, who had requested the material.

Hermann von Schrenk : a biography: botanist, plant pathologist, wood preserving scientist, pioneer in American wood preservation, forest scientist, forester, timber engineer.

Mode of access: Internet.

Location model for CCA-treated - wood waste remediation units

Dissertação apresentada como requisito parcial para obtenção do grau de Mestre em Ciência e Sistemas de Informação Geográfica

Field Evaluation of Timber Preservation Treatments for Highway Applications Final Report, December 2007

Timber material repair and replacement cost for timber bridges is a considerable expense to highway agencies in Iowa, especially to county road departments. To address these needs, the objectives of this investigation was to study the field effectiveness of various treatment alternatives used on Iowa roadway projects and to determine if the current specifications and testing are adequate for providing proper wood preservation. To satisfy the research needs, the project scope involved a literature review, identification of metrics, questionnaire survey of Iowa counties, onsite inspections, and a review of current specifications and testing procedures. Based on the preservative information obtained, the following general conclusions were made: Copper naphthenate is recommended as the plant-applied preservative treatment for timber bridges. Best Management Practices should be followed to ensure quality treatment of timber materials. Bridge maintenance programs need to be developed and implemented. The Iowa Department of Transportation specifications for preservative treatment are the regulating specification for bridges constructed with state or federal funding in Iowa and are also recommended for all other bridges.

Effects of Surface Properties and Wood Modification into Direct Printing on Wood

Building industry is a high volume branch which could provide prominent markets for wood based interior decoration solutions. Competition in interior decoration markets requires versatility in appearance. Versatility in wood appearance and added value could be achieved by printing grain patterns of different species or images directly onto wood. The problem when planning wood printing’s implementing into durable applications is basically how to transfer a high quality image or print sustainably onto wood, which is porous, heterogeneous, dimensionally unstable, non-white and rough. Wood preservation or treating, and modification can provide durability against degradation but also effect to the surface properties of wood which will effect on printability. Optimal adhesion is essential into print quality, as too high ink absorbance can cause spreading and too low ink absorbance cause pale prints. Different printing techniques have different requirements on materials and production. The direct printing on wood means, that intermedias are not used. Printing techniques with flexible printing plates or in fact non-impact techniques provide the best basis for wood printing. Inkjet printing of wood with different mechanical or chemical surface treatments, and wood plastic composite material gave good results that encourage further studies of the subject. Sanding the wood surface anti-parallel to the grain gave the best overall printing quality. Spreading parallel to the grain could not be avoided totally, except in cases where wood was treated hydrophobic so adhesion of the ink was not sufficient. Grain pattern of the underlying wood stays clearly visible in the printed images. Further studies should be made to fine tune the methods that already gave good results. Also effects of moisture content of wood, different inks, and long-term exposure to UV-radiation should be tested.

The Brazilian architecture in wood and the confrontations with the questions of the environment

Two discussions are imposed to the designers of wood constructions. The first one deals with the technical knowledge to project and execute buildings; the second one is concerned with the preservation of the environment, use of the wood in a sustainable way. The work presents the tendencies of the wood used in the Brazilian habitation architecture characterizing the used woods; how the construction technical solutions have developed and discusses about the necessity of using the wood in a conscious way, knowing its origin and control, sustainable use of the forests resources. It focalizes, mainly, the search of the designers to harmonize the use of the wood and the preservation of the forest biodiversity, when it deals with the native forest.

Evaluation of area contaminated by wood treatment activities: genetic markers in the environment and in the child population

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

State of the art of industrial wood protection in Portugal

This work intended to give a perspective of industrial wood protection in Portugal. A survey was made of the companies treating wood mainly for use classes 3 and 4 such as autoclave treatments with biocides and wood modification procedures. Currently there are 23 companies with 33 production plants with an autoclave installed for wood preservation by impregnation. There are also two companies producing modified wood by thermal treatment. Most of the plants are located in the central and northern regions of Portugal. The leading preservation chemicals used in Portugal are Tanalith E and Celcure brands. The main wood species used in all companies is Pinus pinaster from local producers. The products commercialized by the treating companies are diverse: pre-fabricated houses, garden furniture and playgrounds, decks, poles, stakes, and sawn wood. Modified wood producers sell mostly decks and cladding. Considerable changes are expected in the next few years due to the requirements of European Directives and the typical constraints of the Portuguese market.

Studies on isolation, purification and properties of Endoglucanase from the hepatopancreas of Perna viridis

In the attempt to find out catalytic potency and properties of the endoglucanase of green mussel, it could be highlighted that the enzyme is efficient in degrading carboxymethylcellulose to reducing sugars. The immobilized enzyme will find applications in the food industry, paper and pulp industry, wood preservation, alcohol and pharmaceutical industry.The purification method employed i.e. Sephadex G100 chromatography employing affinity and exclusion principles simplify the purification procedure.Addition of Mg2+ and Co2+ at 10mM concentrations enhances endoglucanase activity of green mussel.The immobilized endoglucanase can be used for deinking mixed office waste paper. The endoglucanase if supplemented with exoglucanase and B-glucosidase under appropriate conditions would help in the recycling of paper.

Avaliação de nove espécies de Eucalyptus spp. em tratamento preservativo industrial

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Biochar and compost effects on mobility of Cu and other soil parameters and plant growth

A pot experiment was conducted to determine the effects of three biochars and compost on plant growth and the immobilisation of Cu in a contaminated soil obtained from a former wood preservation site in the Gironde County Saint Médard d'Eyrans, France (N 44° 43.353, W 0° 30.938). To assess Cu mobility, amended soils were analysed using CaCl**2 leaching tests pre- and post-incubation, and post-growth. Amended and unamended soils were planted with sunflower, and the resulting plant material was assessed for yield (mass and height) and Cu concentration. All amendments significantly reduced leachable Cu compared to the unamended soil, however, the greatest reductions in leachable Cu were associated with the higher biochar application rate. The greatest improvements in plant yields were obtained with the higher application rate of biochar in combination with compost. pH, DOC, EH were measured in soils to help explain the leaching and plant growth trends. Soil pore water was collected during plant growth and analysed for metal concentration, pH and EH. Prior to treatment, background analyses were carried out on the soil and individual amendments (including PAH + metal concentrations measured by gas chromatography mass spectrometry and ICP-AES respectively).

STUDIES OF FUNCTIONALIZED NANOPARTICLES FOR SMART SELF-ASSEMBLY AND AS CONTROLLED DRUG DELIVERY

This dissertation is related to the studies of functionalized nanoparticles for self-assembly and as controlled drug delivery system. The whole topic is composed of two parts. In the first part, the research was conducted to design and synthesize a new type of ionic peptide-functionalized copolymer conjugates for self-assembly into nanoparticle fibers and 3D scaffolds with the ability of multi-drug loading and governing the release rate of each drug for tissue engineering. The self-assembly study confirmed that such peptide-functionalized amphiphilic copolymers underwent different self-assembly behavior. The bigger nanoparticles were more easily assembled into nanoparticle fibers and 3D scaffolds with larger pore size, while the smaller nanoparticle underwent faster self-assembly to form more compact 3D scaffolds with smaller porosity but more stable structure. Controlled release studies confirmed the ability of governing simultaneous release of different model drugs with independent release rate from a same scaffold. Cytotoxicity tests showed that all synthesized peptides, copolymers and peptide-copolymer conjugates were biocompatible with SW-620 cell lines and NIH3T3 cell lines. This new type of self-assembled scaffolds combined the advantages of peptide nanofibers and versatile controlled release of polymeric nanoparticles to achieve simultaneous multi-drug loading and controlled release of each drug, uniform distribution and flexibility of hydrogel scaffolds. The investigations in second part were first to design and synthesize organic biocide-loaded nanoparticles for low-leaching wood preservation using a cost-effective one-pot method to synthesize amphiphilic chitosan-g-PMMA nanoparticles loading with ~25-28 wt.% of the fungicide tebuconazole with particle size of ~100 nm diameter by FESEM. FESEM analysis confirmed efficient penetration of nanoparticles throughout the treated wooden stake with dimension of 19 × 19 × 455 mm^3. Leaching studies showed that biocide introduced into sapwood via nanoparticles leached only ~9% compared with the amount leached from tebuconazole solution-treated control, while soil jar tests showed that the nanoparticle-treated wood blocks were effectively protected from biological decay tested against G. trabeum, a brown rot fungus. Copper oxide nanoparticles with and without polymer stabilizers were also investigated to use as inorganic wood preservatives to clarify the factor affecting copper leaching from treated wood. Copper oxide nanoparticles with uniform diameters of ~10 nm and ~50 nm were prepared, and the leachates from southern pine sapwood treated with these nanoparticles were analyzed. It was found by TEM and EDS analysis that significant numbers of nanoparticles leached from the treated wood. The 50 nm nanoparticles leached slightly less than a soluble copper salt control, but 10 nm nanoparticles leached substantially more than the control. The effect of polymer stabilizers on nanoparticle leaching was also investigated. Results showed that polymer stabilizers increased leaching. The trends showed that nanoparticle size was a major factor in copper leaching.

A complete body of husbandry; collected from the practice and experience of the most considerable farmers in Britain. Particularly setting forth the various ways of improving land ... To which is added several particulars relating to the preservation of the game; and stated accounts of the expence and profits of arable, pasture, meadow and wood lands. Adorn'd with cuts.

Title-page in red and black.

PRESERVATION OF PRIMARY FOREST CHARACTERISTICS DESPITE FRAGMENTATION AND ISOLATION IN A FOREST REMNANT FROM VIÇOSA, MG, BRAZIL1

According to its owners, the Forest of Seu Nico (FSN) from the Viçosa municipality, Minas Gerais, Brazil, never has been logged and is therefore considered a primary forest. Nevertheless, the forest patch suffered impacts due to selective wood and non-timber extraction, fragmentation and isolation. Aim of this study was to test if the FSN, despite impacts, preserved characteristics of primary forests, which are elevated percentages of non-pioneer (>90%), animal-dispersed (>80 %), understory (>50%) and endemic species (~40%). For that, all trees with diameter at breast height equal or major than 3.2 cm within a plot of 100 x 100 m were identified. With 218 tree species found within this hectare, the FSN's species richness is outstanding for the region. The percentages of non-pioneer (92 %), animal-dispersed (85 %), understory (55 %) and endemic species (39.2 %) from the FSN fulfill the criteria proposed for primary forest. Therefore, we conclude that the FSN maintained its characteristics as a primary forest which highlights its importance for the conservation of biotic resources in the region, where similar fragments are lacking or not described yet.