962 resultados para Wood - Juvenile and mature
Resumo:
The aim of this study was to verify the average fiber length and the juvenile and mature wood zones from Hevea brasiliensis proveniences from a reforestation area in São Paulo, Brazil. For this purpose, five Hevea brasiliensis trees were randomly collected from a 50-year-old plantation, located in Balsamo, São Paulo, Brazil. The trees were cut and five flat sawn boards were obtained. The juvenile and mature wood zones were determined by fiber length measurement from the pith to the bark. The results showed that: (a) the juvenile wood of this species occurred approx. between 40 and 55 mm, from the pith, and from this point forward, the mature wood zone was found; (b) there was a significant difference between the average fiber length of juvenile wood (1.26 mm) and mature wood (1.51 mm).
Resumo:
Peer reviewed
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Kraft pulp produced from juvenile and mature wood from thirty-two-year-old Corymbia citriodora trees was evaluated. The stem was subdivided into regions of juvenile and mature wood, and then it was transformed into chips. These materials were then cooked in the Laboratory of Pulp and Paper at São Paulo State University (UNESP, Botucatu, SP, Brazil) and the physico-mechanical properties of the pulps were determined. The results showed that: (1) the pulp yields of mature wood were up to 4.4% greater in comparison to the juvenile wood, (2) the juvenile wood pulp required a shorter refining time than mature wood to reach the same Schopper-Riegler degree, (3) the juvenile wood pulp presented lower specific volume, and (4) the mature wood pulp presented greater air resistance, tensile, tear and burst index values, stress-strain factor, and stretch than the juvenile wood pulp.
Resumo:
This study aimed to evaluate the effect of thermal treatment on the physical properties of juvenile and mature woods of Eucalyptus grandis. Boards were taken from 30-year-old E. grandis trees. The boards were thermally modified at 180 °C in the Laboratory of Wood Drying and Preservation at UNESP, Botucatu, Sao Paulo state, Brazil. The results showed that thermal modification caused: (1) decrease of 6.8% in the density at 0% equilibrium moisture content of mature wood; (2) significant decreases of 14.7% and 35.6% in the maximum volumetric swellings of juvenile and mature woods, respectively; (3) significant decreases of 13.7% and 21.3% in the equilibrium moisture content of juvenile and mature woods, respectively. The influence of thermal modification in juvenile wood was lower than in mature wood and caused greater uniformity in the physical variations between these types of wood in E. grandis.
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)
Resumo:
There is a strong desire to exploit transcriptomics data from model species for the genetic improvement of non-model crops. Here, we use gene expression profiles from the commercial model Pinus taeda to identify candidate genes implicated in juvenile-mature wood transition in the non-model relative, P. sylvestris. Re-analysis of 'public domain' SAGE data from xylem tissues of P. taeda revealed 283 mature-abundant and 396 juvenile-abundant tags (P < 0.01), of which 70 and 137, respectively matched to genes with known function. Based on sequence similarity, we then isolated 16 putative homologues of genes that in P. taeda exhibited widest divergence in expression between juvenile and mature samples. Candidate expression levels in P. sylvestris were almost invariably differential between juvenile and mature woody tissue samples among two cohorts of five trees collected from the same seed source and selected for genetic uniformity by genetic distance analysis. However, the direction of differential expression was not always consistent with that described in the original P. taeda SAGE data. Correlation was observed between gene expression and juvenile-mature wood anatomical characteristics by OPLS analysis. Four candidates (alpha-tubulin, porin MIP1, lipid transfer protein and aquaporin like protein) apparently had greatest influence on the wood traits measured. Speculative function of these genes in relation to juvenile-mature wood transition is briefly explored. Thus, we demonstrate the feasibility of exploiting SAGE data from a model species to identify consistently differentially expressed candidates in a related non-model species.
Resumo:
Pós-graduação em Agronomia (Energia na Agricultura) - FCA
Resumo:
In this paper it was evaluated the influence of the relative position of logs on the trees, the type of wood (juvenile and mature wood and pith) and the dimension of sawed wood elements on the velocity of propagation of stress waves into the material on condition. P. taeda L wood (43 years old trees) from Horto Florestal of Manduri (latitude 230 00’ south, longitude 400 19’ west and altitude de 700 m) São Paulo State, Brazil were used, considering its easy growth rings visualization and the better ju regions definition. Six trees were randomly chosen in the plantation. Trees were sawed into 4 logs (2,5 m long each. In each log it was delimited the central board (80mm tick) region and the lateral boards (25mm tick) regions, cons right hand. It were evaluated relation between velocity of stress waves on logs and the correspondent lumber (central and lateral boards), on green condition, on the three main region of the elements (mature wood results obtained revealed the concordance between velocities of stress waves in the material before and after the its mechanical processing. It was also revealed statistical differences between the velocity of stress waves at juvenile wood, mature wood and pith regions. Keywords: stress wave method, velocity 17 destrutivos de propagação da propagação de ondas de tensão em toras e madeira serrada de taeda L. Hernando Alfonso Lara Palma - Universidade Estadual Paulista Faculdade de Ciências Agronômicas – FCA/UNESP – Botucatu - SP, e-mail: awballarin@fca.unesp.br Luiz Antonio Vasques Hellmeister - Universidade Estadual Paulista - Faculdade de Arquitetura, FAAC/UNESP – Bauru - SP, e-mail: hellmeister@faac.unesp.br Este trabalho teve como objetivo analisar a influência do tipo de lenho, da posição da tora ao longo do fuste e das dimensões das peças desdobradas, na velocidade de as de tensão (Stress wave method), na condição de madeira verde. P. taeda L., originária de árvores de plantio do Horto Florestal de SP., com idade aproximada de 43 anos, pela facilidade de identificação dos anéis imento e demarcação das regiões de madeira adulta e madeira juvenil. Foram amostradas 6 árvores distintas, escolhidas ao acaso do talhão selecionado. De cada árvore foram retiradas 4 toras com comprimento de 2,5 m cada. Foram demarcadas nas toras a ha central (8 cm de espessura) e 4 tábuas laterais (espessura comercial de 2,5 cm), sendo duas à esquerda e duas à direita da prancha central. Foram avaliadas as relações existentes entre as velocidades de propagação das ondas de tensão na madeira íntegra (toras) e desdobrada (pranchas e tábuas), na condição de madeira verde, nas três regiões distintas do lenho: medula, madeira adulta e madeira juvenil. A análise comparativa dos resultados revelou a concordância entre as velocidades antes e após o desdobr madeira. Houve diferenciação estatisticamente significativa entre as velocidades de propagação das ondas de tensão nos lenhos adulto, juvenil e na medula. -destrutivos, método das ondas de tensão, Pinus taeda stress wave tests on green logs and lumber of Pinus taeda In this paper it was evaluated the influence of the relative position of logs on the trees, the type of wood (juvenile and mature wood and pith) and the dimension of sawed wood elements on the velocity of propagation of stress waves into the material on L wood (43 years old trees) from Horto Florestal of Manduri (latitude 19’ west and altitude de 700 m) São Paulo State, Brazil were used, considering its easy growth rings visualization and the better juvenile and mature wood regions definition. Six trees were randomly chosen in the plantation. Trees were sawed into 4 logs (2,5 m long each. In each log it was delimited the central board (80mm tick) region and the lateral boards (25mm tick) regions, considering 2 boards on the left and 2 at the right hand. It were evaluated relation between velocity of stress waves on logs and the correspondent lumber (central and lateral boards), on green condition, on the three main region of the elements (mature wood, juvenile wood and pith). Comparative analyses of results obtained revealed the concordance between velocities of stress waves in the material before and after the its mechanical processing. It was also revealed statistical differences ty of stress waves at juvenile wood, mature wood and pith regions
Resumo:
The objective of this study was to show the radial variation of some anatomic characteristics, wood density and natural durability of teak (Tectona grandis L.F.) growing in Costa Rica. Samples of trees 13 years old were obtained from two growing sites (high and low growing) of plantations established in a humid tropical climate (CHT) and dry tropical climate (CST). The variables measured of the fibers as well as for the rays were not affected by the climate or the type of growing site, except for the length of the fibers. The fibers of teak wood from the best growing site were significantly larger. Vessels were found with a greater frequency for the CST but mostly solitary in comparison with the CBT. Average density, maximum density and the variation within the ring presented a light higher magnitude for the CST. The quality of the growing site did not affect these variables. The resistance of fungus attack was similar in the area of heartwood near the pith compared to the heartwood near the sapwood for all the conditions evaluated. Nevertheless, it was observed in some trees a similar resistance of fungus attack for areas of sapwood compared to similar areas of heartwood.
Resumo:
Tree-rings have frequently been used for dating of trees and to determine annual growth increments and forest dynamics, but little is known in tropical conditions about their utilization for environmental monitoring. This paper presents the results of Araucaria columnaris tree-ring characterization by wood anatomy and X-ray densitometric analysis and the determination of Pb concentration. Core samples from twelve araucaria trees were extracted from two sites exposed to air pollution due to intense traffic of vehicles and industrial activities. The tree-rings distinctly presented radial variation in early-latewood thickness and density, and characteristics of juvenile and mature wood. Anatomical and X-ray densitometric analysis were useful to delimit the tree-ring boundaries and to date the tree-rings, as well as to prove the annual formation. The lead concentration in annual araucaria tree-rings, analyzed with graphite furnace atomic absorption spectrometry, indicated the seasonal presence of the heavy metal in the environment during the 30 years studied, although the Pb did not affect tree growth. (c) 2008 Elsevier GmbH. All rights reserved.
Resumo:
Mahogany trees, Swietenia macrophylla, occur in open rainforest, semi deciduous and deciduous and dense rainforest of Peruvian Amazonian tropical forest. They occur, preferentially, in areas with a defined dry season, with typical phenology and seasonal variation activity, forming distinct tree-rings. The present work had as aim to determine the wood density radial variation of 14 mahogany trees, of two populations of the Peruvian Amazonian tropical forest, through the X-ray densitometry and to evaluate their application as methodology, compared to the classic method of measurement table, for the determination of the treering width. The radial wood apparent density of the trees profiles rendered it possible to delimit the areas of juvenile-adult wood and of the heartwood-sapwood, relative to the anatomical structure and chemical composition differences, due to the extractives and the vessels obstruction by tyloses. The mean, minimum and maximum wood apparent density of the mahogany trees for the Populations A and B were of 0.70; 0.29; 1.01 g.cm(-3) and 0.81; 0.29; 1.19 g.cm(-3), respectively. The analysis of the variance and mean test indicate differences of mean wood density among the mahogany trees of each population, probably due to the age of the trees. There was no correlation between mean wood density of mahogany trees among the two populations, as well as, between the tree-ring width and the respective mean density. The X-ray densitometry technique is an important tool in the evaluation of the radial variation of wood apparent density and the delimitation of tree-ring boundaries, with correlations of 0.94 and 0.93 in relation to measurement table, for each sampled population.
Resumo:
Praziquantel (PZQ) is currently the only drug widely used for the treatment of schistosomiasis, but the antimalarial drug mefloquine (Mef) possesses interesting antischistosomal properties. Combination therapy with these two drugs has been suggested as a strategy for transmission control, as PZQ is active against adult worms and Mef is active against schistosomula. To examine the efficacy of combination therapy, Schistosoma mansoni-reinfected mice were separated into seven groups: untreated (I), treated with PZQ in doses of 200 mg/kg (II) or 1,000 mg/kg (III), treated with Mef in doses of 200 mg/kg (IV) or 400 mg/kg (V); each dose was divided equally and given on two consecutive days. Group VI was treated with doses of PZQ + Mef as in groups II and IV, respectively, while group VII was treated with PZQ + Mef as in groups III and V, respectively. PZQ + Mef at the reduced doses of 200 mg/kg each enhanced the therapeutic efficacy over the reduced PZQ dose alone as shown by a very high reduction in the total numbers of mature worms (95% vs. 49%), immature worms (96% vs. 29%) and the complete eradication of immature females, mature females and immature eggs. The reduction in worm burden was associated with the healing of hepatic granulomatous lesions and the normalisation of all liver enzymes. Therefore, the use of Mef with PZQ is more effective than PZQ alone and should be considered for clinical trials in humans as a potential treatment regimen to prevent treatment failures in areas with high rates of schistosomiasis.
Resumo:
Photoinhibition, as measured by the dark-adapted chlorophyll a fluorescence ratio F-v/F-m, was assessed in Syzygium moorei, a species with dark green juvenile leaves, Syzygium corynanthum, which has light green juvenile leaves, and two species with pink-red juvenile leaves (Syzygium wilsonii and Syzygium luehmannii). All plants were glasshouse-grown (maximum PPFD 1500 mu mol m(-2) s(-1)) under optimum nutrition and water. When measured at midday, dark-adapted F-v/F-m ratios of juvenile leaves gradually increased in art species as percentage of full leaf expansion (% FLE) increased. Fluorescence measurement 3 h after sunset or pre-dawn also showed a developmental effect on F-v/F-m, with juvenile leaves of S, luehmannii and S. wilsonii showing much lower F-v/F-m at all stages of development. Dark-adapted F-v/F-m values in both juvenile and mature leaves generally never exceeded 0.8 at any stage in any of the species. Courses of F-v/F-m on sunny days showed greater diurnal photoinhibition in green juvenile (c, 50% FLE) leaves of S, moorei (24%) and S, corynanthum (36%) than in mature leaves of the previous flush in these species (<10%), Diurnal photoinhibition was statistically similar (18-24%) in pink-red juvenile and green mature leaves of S, luehmannii and S, wilsonii. Re-positioning juvenile leaves of S, wilsonii horizontally increased diurnal photoinhibition, Exposure of leaves to a standard mild photoinhibitory right treatment (30 min at 1000 mu mol m(-2) s(-1)) showed that juvenile leaves of air species had a lower percentage of high energy state quenching (qE) and a higher percentage of photoinhibitory quenching (ql) than mature leaves.