Assessment and control of nanoparticles exposure in welding operations by use of a control banding tool

This paper describes the use of a Control Banding Tool to assess and further control of exposure of nanoparticles emitted during welding operations. The tool was applied to Metal Active Gas (MAG) arc welding of mild and stainless steel, providing semi-quantitative data on the process, so that protection measures could be derived, e.g. exhaust gas ventilation by hoods, local ventilation devices and containment measures. This tool is quite useful to compare and evaluate the characteristics of arc welding procedures so that more eco-friendly processes could be preferred over the more potentially noxious ones.

Fatigue strength: effect of welding type and joint design executed in Ti-6Al-4V structures

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sliding wear of weld layers with application to cane mill shaft rebuilding

Three welding procedures used to rebuild worn shafts in sugar cane mills were analysed: two submerged arc welding processes and one flux cored arc welding (FCAW) process. Sliding wear tests were in accordance with ASTM G 77 standard, using rings of welding material, blocks of bronze SAE 67, and oil as lubricant. The worn surfaces of rings and blocks were analysed by scanning electron microscopy to determine the wear mechanisms. High contact pressure, high operating temperature, and low relative speed were applied in sliding wear tests to match the conditions in sugar cane mills. Transferred material and evidence of adhesive junctions were detected. Additionally, hardened fragments produced abrasive grooves on the worn surfaces. The welding deposits that presented strong adhesion on the worn surface showed higher mass loss than the materials that presented more abrasive characteristics. Plastic mechanical properties were measured and related to the mass loss. The tested materials presented similar hardness but different yield stress and hardening coefficient. A relationship between wear, strain hardening coefficient, and yield stress was found. The welding deposit that presented the highest hardening coefficient showed the highest mass loss, with evidence of severe adhesion on the worn surface.

Liikuntasaumaproblematiikan selvittäminen laivan runkorakenteissa

Nykyään laivan kansirakenteet suunnitellaan pääosin kantaviksi rakenteiksi, mikä edellyttää niiltä suurta lujuutta. Jatkuvasti kasvavissa risteilijöissä ja muissa suurissa aluksissa ongelmaksi muodostuu kansirakenteiden suuret jännitykset. Kansirakenteet sijaitsevat kauimpana laivan neutraaliakselilta, jolloin niissä syntyy suuria venymiä. Kansirakenteista pitää näin ollen suunnitella hyvin kestäviä tai vaihtoehtoisesti tarpeeksi lyhyitä rakenteita. Liikuntasaumojen avulla on 1950 -luvulle asti laivoissa katkaistu pitkät kansirakenteet, mutta hitsausmenetelmien kehittyessä kansirakennukset on tehty yhtenäisiksi kansirakenteiksi. Tämä on tähänastisissa risteilijöissäkin toiminut hyvin, mutta laivojen koon kasvaessa on etsittävä keinoja mahdollisiin runkorakenteiden ja varustelun lujuus- ja väsymisongelmiin. Tavoitteena oli saada aikaan työ, joka olisi hyvä ”työkalu” tuleville tutkimuksille liikuntasaumojen soveltamisessa laivarakenteisiin sekä niihin liittyviin varusteluosiin ja -rakenteisiin. Työssä tutustutaan kirjallisuustutkimuksen avulla liikuntasaumasovelluksiin ja esitellään sovelluksia eri aloilta. Kirjallisuusosuuden päätteeksi esitellään muutama laivarakennesovellus, joita löytyy hieman vanhemmista laivarakenteista. FE analyysiosuudessa tutkitaan liikuntasauman pohjan muodon vaikutusta pohjan jännitystasoihin ja liikuntasaumojen vaikutusta laivan kansirakenteiden jännitystasoihin kolmella eri liikuntasaumojen lukumäärällä. Lisäksi kansirakenteiden jännitystasoja tutkittiin kolmella kansirakenteen leveydellä. Esimerkkejä liikuntasaumoista löytyy monelta eri aloilta, joiden ominaisuuksia yhdistelemällä saavutetaan oikea ratkaisu liikuntasaumojen soveltamisessa laivojen kansirakenteisiin. Lisäksi FE -analyysistä voidaan nähdä, että liikuntasaumat laskevat jännitystasoja laivojen kansirakenteissa. Liikuntasaumojen oikea lukumäärä riippuu hyvin paljon siitä, kuinka paljon kansirakenteen jännityksiä halutaan laskea. Liikuntasauman pohjan muotoa on kehitettävä ja se on otettava myös huomioon yhtenä tärkeänä seikkana suunniteltaessa liikuntasaumoja laivojen kansirakenteisiin. Esimerkiksi vahvistelevyillä saadaan jännityksiä laskettua liikuntasauman pohjan läheisyydessä tehokkaasti.

Feasibility studies of the weldability of structural steels used in the offshore environment

The rising demand for oil and gas has made it very necessary for the oil and gas industries to explore the offshore. There is a huge resources which is available in the offshore. The search for oil and gas is faced with greater challenges because of the nature of the marine environment as it poses difficult and harsh conditions for the construction of offshore structures. The major problem of the construction of offshore structure is the ability to produce a sound weld that gives the whole structure the structural integrity needed to withstand the harsh environmental conditions. This research work presents the performance of typical offshore steels with improved weldability. The ability of reducing the carbon content of thermo-mechanically rolled steels down to 0.08% makes it possible to achieve good weldability, toughness and strength for high strength steels used in offshore applications. Importantly, the ideal welding procedure should be strictly followed as recommended. The fabrication process is as important as the welding procedure in achieving a sound weld which is free of weld defects such as hydrogen induced cracking, lamellar tearing and solidification cracking. This research work also considers the corrosion as it affects offshore structure and necessary measures to mitigate the problem caused by corrosion.

Modifioidun MAG-kaarihitsausprosessin hyödyntäminen railotilavuuden pienentämisessä mekanisoidussa orbitaalihitsauksessa.

Länsimaisen työn hinta luo jatkuvan paineen hitsauksen tuottavuuden parantamiseen. MIG/MAG-hitsauksen tuottavuutta voidaan parantaa tehostamalla hitsausprosessia, vähentämällä hitsien lukumäärää ja pienentämällä hitsiaineen tarvetta. Eri virtalähdevalmistajat tuovat markkinoille hitsausprosesseja hitsauksen tehostamiseen, joilla pystytään korvata vähemmän tuottavia hitsaustyövaiheita. Hitsien lukumäärän vähentäminen on rakenteen suunnitteluun liittyvä tekijä ja hitsiaineen tarpeen pienentäminen voidaan toteuttaa railogeometrian muutoksilla tai tuotteen sopivalla suunnittelulla. Diplomityössä on tutkittu 30 mm paksujen S355 rakenneteräsputkien hitsauksen tuottavuuden kasvattamista käyttäen nykyaikaisia modifioituja kaarihitsausprosesseja ja railotilavuutta pienentämällä. Työssä vertailtiin 30o ja 60o railokulmalla tehtyjä liitoksia. Railogeometrian muutoksen lisäksi diplomityössä vertailtiin eri menetelmien tehokkuutta putken pohjapalon hitsauksessa.

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results

Desenvolvimento da Tecnologia de Soldagem do Titânio pelo Processo TIG Orbital no Segmento Aeroespacial Brasileiro - Parte 2: Caracterização das Juntas Soldadas

In this work, three welding programs for orbital TIG previously developed were used, using pulsed current and increasing speed (M), constant current (#B) and pulsed current and decreasing current (#C). One of those should be used for the propulsion system of the satellite CBERS (CHINA-BRAZIL EARTH RESOURCES SATELLITE). Welded joints using tubes of commercially pure titanium were obtained with these procedures, which were characterized by means of mechanical and metallographic tests. The obtained results show that the three welding procedures produce welded joints free of defects and with adequate shape. Although small differences on mechanical properties and microstructure have been observed, the three welding programs attained compatible results with international standards used in the aerospace segment. The welding program #B, due the reduced heat input used, was considered to obtain slightly advantage over the others.

Efeito de dois sistemas de soldagem na alteração dimensional nas ligas de cobalto-cromo verificado por meio de análise por extensometria linear elétrica e resistência à flexão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da influência de aplicação de vibração mecânica na microestrutura e em características mecânicas de juntas do aço inoxidável martensítico CA6NM soldadas pelo processo FCAW

O aço inoxidável martensítico ASTM A743 CA6NM é utilizado para produzir componentes especiais para turbinas hidráulicas, devido às suas boas propriedades mecânicas combinadas com alta resistência à corrosão e cavitação e uma boa soldabilidade. As turbinas hidráulicas são produzidas por meio de múltiplos passes de solda em peças espessas obtidas por fundição. Durante a operação, estes componentes estão sujeitos à erosão por cavitação e trincas em regiões tensionadas, que são reparados também por meio de soldagem. Após o processo de soldagem, um tratamento térmico pós-soldagem é comumente utilizado para aliviar as tensões residuais. Porém, existem dificuldades significativas para a realização de tratamento térmico nas turbinas hidráulicas, tais como a complexidade da geometria de solda, a possibilidade de distorção no caso de quaisquer cargas mecânicas, dificuldade em aquecer simetricamente, e também o tratamento térmico pode causar degradação das propriedades do material. Assim, existe um grande interesse no desenvolvimento de procedimentos de soldagem que elevem a tenacidade ao impacto e evitem o tratamento térmico pós-soldagem. Neste trabalho, a aplicação de vibrações mecânicas durante e após a soldagem para aliviar tensões residuais foram avaliadas em juntas de aço inoxidável martensítico CA6NM soldadas pelo processo Flux Cored Arc Welding (FCAW). A utilização de vibrações mecânicas para reduzir e redistribuir as tensões residuais das estruturas soldadas através da aplicação de carga vibratória pode gerar muitos benefícios. Testes de impacto Charpy (-20 °C), ensaios de tração e dobramento foram realizados conforme ASME IX, e perfis de microdureza nas diferentes regiões da solda foram conduzidos para a caracterização mecânica das juntas soldadas. A caracterização microestrutural foi realizada utilizando difração de raios X, microscopia óptica e microscopia eletrônica de varredura (MEV). Os resultados de propriedades mecânicas das amostras vibradas atenderam as exigências especificadas por norma, na qual o processo com tratamento térmico é recomendado para a soldagem deste tipo de aço, visando atingir os níveis de tenacidade do material original. Com relação à microestrutura não foram observados alterações significativas para as amostras vibradas em comparação com a condição \"como soldado\", porém para a condição com tratamento térmico pós-soldagem foi observado uma pequena quantidade de austenita retida, que são precipitadas após o tratamento térmico e permanecem finamente distribuídas após o resfriamento e auxiliam no ganho de tenacidade das juntas soldadas.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results

The oxy-acetylene handbook : a manual on oxy-acetylene welding and cutting procedures.

Includes index.

Behavior Of Listeria Monocytogenes In A Multi-species Biofilm With Enterococcus Faecalis And Enterococcus Faecium And Control Through Sanitation Procedures.

The formation of mono-species biofilm (Listeria monocytogenes) and multi-species biofilms (Enterococcus faecium, Enterococcus faecalis, and L. monocytogenes) was evaluated. In addition, the effectiveness of sanitation procedures for the control of the multi-species biofilm also was evaluated. The biofilms were grown on stainless steel coupons at various incubation temperatures (7, 25 and 39°C) and contact times (0, 1, 2, 4, 6 and 8days). In all tests, at 7°C, the microbial counts were below 0.4 log CFU/cm(2) and not characteristic of biofilms. In mono-species biofilm, the counts of L. monocytogenes after 8days of contact were 4.1 and 2.8 log CFU/cm(2) at 25 and 39°C, respectively. In the multi-species biofilms, Enterococcus spp. were present at counts of 8 log CFU/cm(2) at 25 and 39°C after 8days of contact. However, the L. monocytogenes in multi-species biofilms was significantly affected by the presence of Enterococcus spp. and by temperature. At 25°C, the growth of L. monocytogenes biofilms was favored in multi-species cultures, with counts above 6 log CFU/cm(2) after 8days of contact. In contrast, at 39°C, a negative effect was observed for L. monocytogenes biofilm growth in mixed cultures, with a significant reduction in counts over time and values below 0.4 log CFU/cm(2) starting at day 4. Anionic tensioactive cleaning complemented with another procedure (acid cleaning, disinfection or acid cleaning+disinfection) eliminated the multi-species biofilms under all conditions tested (counts of all micro-organisms<0.4 log CFU/cm(2)). Peracetic acid was the most effective disinfectant, eliminating the multi-species biofilms under all tested conditions (counts of the all microorganisms <0.4 log CFU/cm(2)). In contrast, biguanide was the least effective disinfectant, failing to eliminate biofilms under all the test conditions.