Water addition, evaporation and water holding capacity of poultry litter

Litter moisture content has been related to ammonia, dust and odour emissions as well as bird health and welfare. Improved understanding of the water holding properties of poultry litter as well as water additions to litter and evaporation from litter will contribute to improved litter moisture management during the meat chicken grow-out. The purpose of this paper is to demonstrate how management and environmental conditions over the course of a grow-out affect the volume of water A) applied to litter, B) able to be stored in litter, and C) evaporated from litter on a daily basis. The same unit of measurement has been used to enable direct comparison—litres of water per square metre of poultry shed floor area, L/m2, assuming a litter depth of 5 cm. An equation was developed to estimate the amount of water added to litter from bird excretion and drinking spillage, which are sources of regular water application to the litter. Using this equation showed that water applied to litter from these sources changes over the course of a grow-out, and can be as much as 3.2 L/m2/day. Over a 56 day grow-out, the total quantity of water added to the litter was estimated to be 104 L/m2. Litter porosity, water holding capacity and water evaporation rates from litter were measured experimentally. Litter porosity decreased and water holding capacity increased over the course of a grow-out due to manure addition. Water evaporation rates at 25 °C and 50% relative humidity ranged from 0.5 to 10 L/m2/day. Evaporation rates increased with litter moisture content and air speed. Maintaining dry litter at the peak of a grow-out is likely to be challenging because evaporation rates from dry litter may be insufficient to remove the quantity of water added to the litter on a daily basis.

The Effect of Turmeric (Curcuma domestica) Extract on Water Holding Capacity, Cooking Loss, pH Values and Tenderness of Broiler Chicken Meat

Abstract.  This study was aimed to determine the influences of turmeric extract supplementation on water holding capacity, cooking loss, pH value and tenderness of broiler chicken meat Data analysis was subject to completely randomized design 5 treatments namely T0, T1, T2, T3 and T4 containing non-turmeric extract, 100 mg/kgBW/day, 200 mg/kgBW/day, 300 mg/kgBW/day and 400 mg/kgBW/day, respectively. Each unit of experiment administered 3 heads with four replications. The results indicated no effect from turmeric extract supplementation on water holding capacity, cooking loss, pH value and tenderness of broiler chicken meat. The average treatments of T0, T1, T2, T3, T4 had water holding capacities of  39.86, 37.58, 36.41, 36.94, respectively; cooking losses of 26.00, 27.58, 27.57, 27.11, and 27.49%, respectively; tenderness of 1.97, 1.95, 1.63, 1.77 and 1.99 Nmm, respectively, and final Body weights of 1,618.5, 1,568, 1,692.5, 1,651.75 and 1,462 g/head, respectively. However, a highly significant influence was observed on the pH values of 6.46, 6.04, 6.21, 6.08 and 5.98. The results indicated that none of the turmeric extract supplementation increased water holding capacity, cooking losses, tenderness and body weight. Key words: broiler, cooking loss, pH values, tenderness, water holding capacity, turmeric Abstrak. Penelitian ini bertujuan untuk mengetahui pengaruh pemberian ekstrak kunyit terhadap daya ikat air, susut masak, nilai pH dan keempukan daging ayam broiler. Manfaat penelitian yaitu tersedianya informasi ilmiah tentang ekstrak kunyit terhadap danging ayam broiler. Perlakuan yang diterapkan adalah T0 tanpa ekstrak kunyit, T1 100, T2 200, T3 300, dan T4 400 mg/kgBB/hari. Data analisis yang digunakan adalah rancangan acak lengkap yang terdiri dari 5 perlakuan dan 4 replikasi. Setiap unit percobaan terdiri dari 3 ekor. Hasil penelitian menunjukkan tidak ada pengaruh pemberian ekstrak kunyit terhadap daya ikat air, susut masak, dan keempukan daging ayam broiler. Rataan untuk perlakuan T0, T1, T2, T3, T4 pada Daya Ikat Air masing–masing 39,86; 37,58; 36,41; 36,94; 34,78%; susut masak 26,00; 27,58; 27,57; 27,11; 27,49%, keempukan 1,97; 1,95; 1,63; 1,77; 1,99 Nmm, dan bobot badan akhir 1.618,5; 1.568; 1.692,5; 1.651,75; 1.462g/ekor. Namun, memberikan pengaruh sangat nyata pada nilai pH 6,46; 6,04; 6,21; 6,08; 5,98. Hasil  menunjukkan bahwa pemberian ekstrak kunyit  tidak meningkatkan daya ikat air, susut masak, keempukan dan bobot badan. Kata Kunci : Broiler, Susut Masak, pH, Keempukan, Daya Ikat Air, Kunyit

Water management capacity building to support rapidly developing mining economies

Many developing countries are experiencing rapid expansion in mining with associated water impacts. In most cases mining expansion is outpacing the building of national capacity to ensure that sustainable water management practices are implemented. Since 2011, Australia's International Mining for Development Centre (IM4DC) has funded capacity building in such countries including a program of water projects. Five projects in particular (principally covering experiences from Peru, Colombia, Ghana, Zambia, Indonesia, Philippines and Mongolia) have provided insight into water capacity building priorities and opportunities. This paper reviews the challenges faced by water stakeholders, and proposes the associated capacity needs. The paper uses the evidence derived from the IM4DC projects to develop a set of specific capacity-building recommendations. Recommendations include: the incorporation of mine water management in engineering and environmental undergraduate courses; secondments of staff to suitable partner organisations; training to allow site staff to effectively monitor water including community impacts; leadership training to support a water stewardship culture; training of officials to support implementation of catchment management approaches; and the empowerment of communities to recognise and negotiate solutions to mine-related risks. New initiatives to fund the transfer of multi-disciplinary knowledge from nations with well-developed water management practices are called for.

Characteristic water contents of a fine-grained soil-water system

This paper critically appraises the limitations of the liquid-limit water content of clayey soils determined conventionally either by percussion cup or by the cone penetration method. It is shown that the conventional liquid limit and plastic limit are arbitrary, strength-based water contents and that they cannot represent the plasticity limits, and that the state of the soil-water system at the conventional liquid limit does not correspond to a stress-free reference state. The present investigation identifies three characteristic limiting water contents for a soil-water system which have well-defined, unique mechanisms controlling them, namely the free swell limit, settling limit and shrinkage limit. Simple procedures for the determination of the free swell limit and settling limit of natural soils are presented. The settling limit is shown to be the 'real liquid limit' of any clayey soil. With a number of experimental illustrations, it is clearly shown that the settling limit represents the maximum water-holding capacity of clayey soils and that it corresponds to the stress-free reference state.

Study on regional differences in soil-water characteristics and their relevance to aquaculture productivity and fish disease

A total of 45 ponds used for fish polyculture were investigated in three zones of Bangladesh to identify the differences among the zones in respect to aqua-ecology, culture practices, fish productivity and health management. Four hundred and fifty fish from three zones were clinically examined by naked eye and histopathology. Out of total number of fish examined, 45 fish from Dhaka zones were examined for parasites and bacteria in addition to histopathology. Faded and haemorrhagic gill, skin, fin, scale loss and lesions were observed during fish examination. Aeromonas spp. Pseudomonas spp. and Streptococcus spp. were isolated respectively from 56%, 46% and 39% affected fish. Among the five water quality parameters analyzed, the highest average hardness and alkalinity respectively were recorded in Rajshahi (156 ppm and 142 ppm) followed by Dhaka (146 ppm and 132 ppm) and Chittagong (81 ppm and 90 ppm). The highest average pH was recorded in Mymensingh (7.52) followed by Rajshahi (7.13) and Chittagong (7.05). Water holding capacity of soil in Rajshahi zone was poor compared to other zones and farmers were found to be reluctant to fish farming.

A Study on the Water Retention Characteristics of Soils and their Improvements

Soil moisture plays a cardinal role in sustaining eclological balance and agricultural development – virtually the very existence of life on earth. Because of the growing shortage of water resources, we have to use the available water most efficiently by proper management. Better utilization of rainfall or irrigation management depends largely on the water retention characteristics of the soil.Soil water retention is essential to life and it provides an ongoing supply of water to plants between periods of irrigation so as to allow their continued growth and survival.It is essential to maintain readily available water in the soil if crops are to sustain satisfactory growth. The plant growth may be retarded if the soil moisture is either deficient or excessive. The optimum moisture content is that moisture which leads to optimum growth of plant. When watering is done, the amount of water supplied should be such that the water content is equal to the field capacity that is the water remained in the saturated soil after gravitational drainage. Water will gradually be utilized consumptively by plants after the water application, and the soil moisture will start falling. When the water content in the soil reaches the value known as permanent wilting point (when the plant starts wilting) fresh dose of irrigation may be done so that water content is again raised to the field capacity of soil.Soil differ themselves in some or all the properties depending on the difference in the geotechnical and environmental factors. Soils serve as a reservoir of the nutrients and water required for crops.Study of soil and its water holding capacity is essential for the efficient utilization of irrigation water. Hence the identification of the geotechnical parameters which influence the water retention capacity, chemical properties which influence the nutrients and the method to improve these properties have vital importance in irrigation / agricultural engineering. An attempt in this direction has been made in this study by conducting the required tests on different types of soil samples collected from various locations in Trivandrum district Kerala, with and without admixtures like coir pith, coir pith compost and vermi compost. Evaluation of the results are presented and a design procedure has been proposed for a better irrigation scheduling and management.

Evaluation of water retention capacity and flood control function of the forest catchment

This research quantitatively evaluates the water retention capacity and flood control function of the forest catchments by using hydrological data of the large flood events which happened after the serious droughts. The objective sites are the Oodo Dam and the Sameura Dam catchments in Japan. The kinematic wave model, which considers saturated and unsaturated sub-surface soil zones, is used for the rainfall-runoff analysis. The result shows that possible storage volume of the Oodo Dam catchment is 162.26 MCM in 2005, while that of Samerua is 102.83 MCM in 2005 and 102.64 MCM in 2007. Flood control function of the Oodo Dam catchment is 173 mm in water depth in 2005, while the Sameura Dam catchment 114 mm in 2005 and 126 mm in 2007. This indicates that the Oodo Dam catchment has more than twice as big water capacity as its capacity (78.4 mm), while the Sameura Dam catchment has about one-fifth of the its storage capacity (693 mm).

Survey of Agricultural Practices and Alternatives to Pesticide Use to Conserve Water Resources in the Mojanda Watershed, Ecuador

Agriculture in the Mojanda Watershed is facing rainfall reductions caused by climate change. Reductions of water availability in the Watershed are also due to constant extension of the agricultural activities into the páramo ecosystem above 3000m a.s.l., with this ecosystem having immanently important functions in the local water balance. The application of pesticides threatens the quality of water and with less precipitation contaminations will further concentrate in the outflow. To analyze problems associated with agricultural practices in the area a questionnaire about agricultural practices (28) was conducted and fields (20) were surveyed for pests and diseases with a focus on potatoes (Solanum tuberosum L.), tree tomatoes (Solanum betaceum Cav.) and peas (Pisum sativum L.). Potatoes were infected to a low degree with Phytophthora infestans and according to the farmers the Andean potato weevil (Premnotrypes spec.) caused biggest losses. To combat the weevil the soils are disinfected with toxic Carbofuran (WHO Class 1B). Tree tomatoes showed symptoms of various fungal diseases. Most important was Fusarium solani causing the branches to rot and Anthracnosis (Colletotrichum gloeosporioides) causing the fruits to rot. Fungicide applications were correspondingly high. Peas were only minorly affected by Ascochyta blight (Mycosphaerella pinodes) and a root rot. Overall 19 active ingredients were applied of which fungicide Mancozeb (WHO class table 5) and insecticide Carbofuran (WHO Class 1B) were applied the most. Approved IPM methods are advised to reduce pesticide use. For tree tomatoes regular cutting of branches infected with F. solani and regular collection and disposal of infected fruits with Anthracnosis are advised. For potatoes plastic barriers around the fields prevent the Andean potato weevil from laying eggs thus reducing infestation with the larvae in the tubers. Local bioinsecticide “Biol” seems effective and without harm to the environment, although not used by many farmers. Organic fertilization promises to restore decreasing soil fertility, water holding capacity and reduce erosion. The here presented alternatives and strategies to reduce pesticide use pose an opportunity to preserve the water resources of the region.

Development of the Surface Urban Energy and Water balance Scheme (SUEWS) for cold climate cities

The Surface Urban Energy and Water Balance Scheme (SUEWS) is developed to include snow. The processes addressed include accumulation of snow on the different urban surface types: snow albedo and density aging, snow melting and re-freezing of meltwater. Individual model parameters are assessed and independently evaluated using long-term observations in the two cold climate cities of Helsinki and Montreal. Eddy covariance sensible and latent heat fluxes and snow depth observations are available for two sites in Montreal and one in Helsinki. Surface runoff from two catchments (24 and 45 ha) in Helsinki and snow properties (albedo and density) from two sites in Montreal are also analysed. As multiple observation sites with different land-cover characteristics are available in both cities, model development is conducted independent of evaluation. The developed model simulates snowmelt related runoff well (within 19% and 3% for the two catchments in Helsinki when there is snow on the ground), with the springtime peak estimated correctly. However, the observed runoff peaks tend to be smoother than the simulated ones, likely due to the water holding capacity of the catchments and the missing time lag between the catchment and the observation point in the model. For all three sites the model simulates the timing of the snow accumulation and melt events well, but underestimates the total snow depth by 18–20% in Helsinki and 29–33% in Montreal. The model is able to reproduce the diurnal pattern of net radiation and turbulent fluxes of sensible and latent heat during cold snow, melting snow and snow-free periods. The largest model uncertainties are related to the timing of the melting period and the parameterization of the snowmelt. The results show that the enhanced model can simulate correctly the exchange of energy and water in cold climate cities at sites with varying surface cover.

INCREASED WATER STORAGE CAPACITY IN CACTUS WOOD: A STUDY IN THE TRIBE CEREEAE (CACTOIDEAE, CACTACEAE)

Secondary xylem of fibrous cactus wood is characterized by short narrow vessel elements with both simple perforation plates and large intervessel pits, libriform septate fibers, and large rays. These are present in basal cactus taxa, as well as in many other groups of the family. In Cactoideae, the most diversified and most derived subfamily, there are remarkable variations found in the secondary xylem, with the more highly derived taxa containing the greatest water storage capacity. Unlignified parenchyma is one specialization found in the fibrous wood of cacti. We observed this tissue in the secondary xylem at the base of the sterns of several Brazilian endemic species of Arrojadoa, Melocactus, and Stephanocereus, all members of the tribe Cereeae. In Arrojadoa and Melocactus the unlignified parenchyma occurs in lines and bands amongst the axial and radial xylem elements, while in Stephanocereus it is mainly restricted to the rays and does not form bands. We address the adaptive importance of the unlignified parenchyma in the fibrous wood in tribe Cereeae and the family Cactaceae as a whole.

Dry spell mitigation to upgrade semi-arid rainfed agriculture : Water harvesting and soil nutrient management for smallholder maize cultivation in Machakos, Kenya

Improvements in on-farm water and soil fertility management through water harvesting may prove key to up-grade smallholder farming systems in dry sub-humid and semi-arid sub-Sahara Africa (SSA). The currently experienced yield levels are usually less than 1 t ha-1, i.e., 3-5 times lower than potential levels obtained by commercial farmers and researchers for similar agro-hydrological conditions. The low yield levels are ascribed to the poor crop water availability due to variable rainfall, losses in on-farm water balance and inherently low soil nutrient levels. To meet an increased food demand with less use of water and land in the region, requires farming systems that provide more yields per water unit and/or land area in the future. This thesis presents the results of a project on water harvesting system aiming to upgrade currently practised water management for maize (Zea mays, L.) in semi-arid SSA. The objectives were to a) quantify dry spell occurrence and potential impact in currently practised small-holder grain production systems, b) test agro-hydrological viability and compare maize yields in an on-farm experiment using combinations supplemental irrigation (SI) and fertilizers for maize, and c) estimate long-term changes in water balance and grain yields of a system with SI compared to farmers currently practised in-situ water harvesting. Water balance changes and crop growth were simulated in a 20-year perspective with models MAIZE1&2. Dry spell analyses showed that potentially yield-limiting dry spells occur at least 75% of seasons for 2 locations in semi-arid East Africa during a 20-year period. Dry spell occurrence was more frequent for crop cultivated on soil with low water-holding capacity than on high water-holding capacity. The analysis indicated large on-farm water losses as deep percolation and run-off during seasons despite seasonal crop water deficits. An on-farm experiment was set up during 1998-2001 in Machakos district, semi-arid Kenya. Surface run-off was collected and stored in a 300m3 earth dam. Gravity-fed supplemental irrigation was carried out to a maize field downstream of the dam. Combinations of no irrigation (NI), SI and 3 levels of N fertilizers (0, 30, 80 kg N ha-1) were applied. Over 5 seasons with rainfall ranging from 200 to 550 mm, the crop with SI and low nitrogen fertilizer gave 40% higher yields (**) than the farmers’ conventional in-situ water harvesting system. Adding only SI or only low nitrogen did not result in significantly different yields. Accounting for actual ability of a storage system and SI to mitigate dry spells, it was estimated that a farmer would make economic returns (after deduction of household consumption) between year 2-7 after investment in dam construction depending on dam sealant and labour cost used. Simulating maize growth and site water balance in a system of maize with SI increased annual grain yield with 35 % as a result of timely applications of SI. Field water balance changes in actual evapotranspiration (ETa) and deep percolation were insignificant with SI, although the absolute amount of ETa increased with 30 mm y-1 for crop with SI compared to NI. The dam water balance showed 30% productive outtake as SI of harvested water. Large losses due to seepage and spill-flow occurred from the dam. Water productivity (WP, of ETa) for maize with SI was on average 1 796 m3 per ton grain, and for maize without SI 2 254 m3 per ton grain, i.e, a decerase of WP with 25%. The water harvesting system for supplemental irrigation of maize was shown to be both biophysically and economically viable. However, adoption by farmers will depend on other factors, including investment capacity, know-how and legislative possibilities. Viability of increased water harvesting implementation in a catchment scale needs to be assessed so that other down-stream uses of water remains uncompromised.

Tab. 1: Mean water loss by mosses and lichens at 40%

The loss of water in a desiccating atmosphere (c.40% r.h. at 10°C) and uptake of water from a saturated atmosphere (100% r.h. at 10°C) was recorded at intervals over periods of many hours or days in the dominant mosses and macroiichens occurring near the Australian Casey Station. Wilkes Land, continental Antarctica. While major differences exist in the water holding capacity and rates of water loss between mosses and lichens, the minimum levels attained after prolonged exposure to desiccating conditions are remarkably similar. By contrast, the volume of water absorbed from a saturated atmosphere is very similar in both groups of cryptogams. Morphological and anatomical characters are responsible for many of the differences, both between species, and within species exhibiting different growth features. Thus, significantly larger amounts of water are held by colonies of Bryum algens with a dense tomentum of rhizoids than those with sparse rhizoids; similarly, the rhizinate Umbilicaria aprina held a greater volume of water than the erhizinate U. decussata. The filamentous mat form of Alectoria mimiscula permits a much higher water content to be attained than in the coarser fruticose forms of Usnea sphacelata and U. antarctica. The dense shoot arrangement in Schistidium antarcticum accounts for the high water holding capacity in the hydric turf form whereas the less densely packed shoots and thicker cell walls of the xeric cushion form maintain a lower water content. The rate of water loss (as percentage dry weight) was much faster in the turf form of Schistidium and tomenlose form of Bryum, although this trend was reversed when expressed as percentage of the initial water content. Minimal water contents arc achieved by the lichens in desiccating conditions within 6-12 hours, whereas the mosses take several times longer. The water relations characteristics of these cryptogams are considered in the light of their distribution in the field and of their metabolic activity under prevailing Antarctic conditions.

Hydraulic properties of layered soils influence survival of Rhodes grass (Chloris gayana Kunth.) during water stress

Survival of vegetation on soil-capped mining wastes is often impaired during dry seasons due to the limited amount of water stored in the shallow soil capping. Growth and survival of Rhodes grass (Chloris gayana) during soil drying on various layered capping sequences constructed of combinations of topsoil, subsoil, seawater-neutralised residue sand and low grade bauxite was determined in a glasshouse. The aim was to describe the survival of Rhodes grass in terms of plant and soil water relationships. The soil water characteristic curve and soil texture analysis was a good predictor of plant survival. The combination of soil with a high water holding capacity and low soil water diffusivity (e.g. subsoil with high clay contents) with soil having a high water holding capacity and high diffusivity (e.g. residue sand) gave best survival during drying down (up to 88 days without water), whereas topsoil and low grade bauxite were unsuitable (plants died within 18-39 days). Clayey soil improved plant survival by triggering a water stress response during peak evaporative water demand once residue sand dried down and its diffusivity fell below a critical range. Thus, for revegetation in seasonally dry climates, soil capping should combine one soil with low diffusivity and one or more soils with high total water holding capacity and high diffusivity.

Evaluating responses to land degradation mitigation measures in Southern Italy

The main factors affecting environmental sensitivity to degradation are soil, vegetation, climate and management, through either their intrinsic characteristics or by their interaction on the landscape. Different levels of degradation risks may be observed in response to particular combinations of the aforementioned factors. For instance, the combination of inappropriate management practices and intrinsically weak soil conditions will result in a severe degradation of the environment, while the combination of the same type of management with better soil conditions may lead to negligible degradation.The aim of this study was to identify factors and their impact on land degradation processes in three areas of the Basilicata region (southern Italy) using a procedure that couples environmental indices, GIS and crop-soil simulation models. Areas prone to desertification were first identified using the Environmental Sensitive Areas (ESA) procedure. An analysis for identifying the weight that each of the contributing factor (climate, soil, vegetation, management) had on the ESA was carried out using GIS techniques. The SALUS model was successfully executed to identify the management practices that could lead to better soil conditions to enhance land use sustainability. The best management practices were found to be those that minimized soil disturbance and increased soil organic carbon. Two alternative scenarios with improved soil quality and subsequently improving soil water holding capacity were used as mitigation measures. The ESA were recalculated and the effects of the mitigation measures suggested by the model were assessed. The new ESA showed a significant reduction on land degradation.

Effect of depithing on the safety and environmental aspects of bagasse stockpiling

Large scale sugarcane bagasse storage in uncovered stockpiles has the potential to result in adverse impacts on the environment and surrounding communities through hazards associated with nuisance dust, groundwater seepage, spontaneous combustion and generation of contaminated leachates. Managing these hazards will assist in improved health and safety outcomes for factory staff and reduced potential environmental impacts on surrounding communities. Removal of the smaller fibres (pith) from bagasse prior to stockpiling reduced the dust number of bagasse by 50% and modelling suggests peak ground level PM10 dust emissions would reduce by 70%. Depithed bagasse has much lower water holding capacity (~43%) than whole bagasse. This experimental and modelling study investigated the physical properties of depithed and whole bagasse. Dust dispersion modelling was undertaken to determine the likely effects associated with storage of whole and depithed sugarcane bagasse.