Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

Organic Matter Removal from Piggery Wastewater in Waste Stabilisation Pond in Nigeria

Four (4) wastewater quality variables: chemical oxygen demand (COD), total solid (TS), total dissolved solid (TDS), and total suspended solid (TSS) were determined. Analysed samples comprises of raw influent and effluents entering and leaving the stabilisation ponds. Significant reduction in variables were obtained, maximum and minimum values obtained for COD were 917mg/l (anaerobic pond), and 13mg/l (maturation pond). For TS, TDS and TSS, maximum and minimum values obtained were 14,420mg/l, 9,180mg/l, 5,240mg/l and 3,398mg/l, 3,120mg/l, 278mg/l respectively. Removal efficiencies recorded for parameters in final effluent (maturation pond) were 98.55% (COD), 76.44% (TS), 66.01% (TDS), and 94.69% (TSS) respectively.

Analysis of vineyard differential management zones and relation to vine development, grape maturity and quality

The objective of research was to analyse the potential of Normalized Difference Vegetation Index (NDVI) maps from satellite images, yield maps and grapevine fertility and load variables to delineate zones with different wine grape properties for selective harvesting. Two vineyard blocks located in NE Spain (Cabernet Sauvignon and Syrah) were analysed. The NDVI was computed from a Quickbird-2 multi-spectral image at veraison (July 2005). Yield data was acquired by means of a yield monitor during September 2005. Other variables, such as the number of buds, number of shoots, number of wine grape clusters and weight of 100 berries were sampled in a 10 rows × 5 vines pattern and used as input variables, in combination with the NDVI, to define the clusters as alternative to yield maps. Two days prior to the harvesting, grape samples were taken. The analysed variables were probable alcoholic degree, pH of the juice, total acidity, total phenolics, colour, anthocyanins and tannins. The input variables, alone or in combination, were clustered (2 and 3 Clusters) by using the ISODATA algorithm, and an analysis of variance and a multiple rang test were performed. The results show that the zones derived from the NDVI maps are more effective to differentiate grape maturity and quality variables than the zones derived from the yield maps. The inclusion of other grapevine fertility and load variables did not improve the results.

Kalman Filtering in Online Paper Quality Assessment

Controlling the quality variables (such as basis weight, moisture etc.) is a vital part of making top quality paper or board. In this thesis, an advanced data assimilation tool is applied to the quality control system (QCS) of a paper or board machine. The functionality of the QCS is based on quality observations that are measured with a traversing scanner making a zigzag path. The basic idea is the following: The measured quality variable has to be separated into its machine direction (MD) and cross direction (CD) variations due to the fact that the QCS works separately in MD and CD. Traditionally this is done simply by assuming one scan of the zigzag path to be the CD profile and its mean value to be one point of the MD trend. In this thesis, a more advanced method is introduced. The fundamental idea is to use the signals’ frequency components to represent the variation in both CD and MD. To be able to get to the frequency domain, the Fourier transform is utilized. The frequency domain, that is, the Fourier components are then used as a state vector in a Kalman filter. The Kalman filter is a widely used data assimilation tool to combine noisy observations with a model. The observations here refer to the quality measurements and the model to the Fourier frequency components. By implementing the two dimensional Fourier transform into the Kalman filter, we get an advanced tool for the separation of CD and MD components in total variation or, to be more general, for data assimilation. A piece of a paper roll is analyzed and this tool is applied to model the dataset. As a result, it is clear that the Kalman filter algorithm is able to reconstruct the main features of the dataset from a zigzag path. Although the results are made with a very short sample of paper roll, it seems that this method has great potential to be used later on as a part of the quality control system.

Wheat protein quality in relation to baking performance evaluated by the Chorleywood bread process and a hearth bread baking test

The relationships between wheat protein quality and baking properties of 20 flour samples were studied for two breadmaking processes; a hearth bread test and the Chorleywood Bread Process (CBP). The strain hardening index obtained from dough inflation measurements, the proportion of unextractable polymeric protein, and mixing properties were among the variables found to be good indicators of protein quality and suitable for predicting potential baking quality of wheat flours. By partial least squares regression, flour and dough test variables were able to account for 71-93% of the variation in crumb texture, form ratio and volume of hearth loaves made using optimal mixing and fixed proving times. These protein quality variables were, however, not related to the volume of loaves produced by the CBP using mixing to constant work input and proving to constant height. On the other hand, variation in crumb texture of CBP loaves (54-55%) could be explained by protein quality. The results underline that the choice of baking procedure and loaf characteristics is vital in assessing the protein quality of flours. (C) 2003 Elsevier Ltd. All rights reserved.

Application Of Real-Time Control Strategy To Improve Nitrogen Removal In Wastewater Treatment

Biological nitrogen removal is an important task in the wastewater treatment. However, the actual removal of total nitrogen (TN) in the wastewater treatment plant (WWTP) is often unsatisfactory due to several causes, one of which is the insufficient availability of carbon source. One possible approach to improve the nitrogen removal therefore is addition of external carbon source, while the amount of which is directly related to operation cost of a WWTP. It is obviously necessary to determine the accurate amount of addition of external carbon source according to the demand depending on the influent wastewater quality. This study focused on the real-time control of external carbon source addition based on the on-line monitoring of influent wastewater quality. The relationship between the influent wastewater quality (specifically the concentration of COD and ammonia) and the demand of carbon source was investigated through experiments on a pilot-scale A/O reactor (1m3) at the Nanjing WWTP, China. The minimum doses of carbon source addition at different situations of influent wastewater quality were determined to ensure the effluent wastewater quality meets the discharge standard. The obtained relationship is expected to be applied in the full-scale WWTPs. .

Effect of citrus sudden death on yield and quality of sweet orange cultivars in Brazil

Citrus sudden death (CSD) has greatly affected sweet orange cultivars grafted on Rangpur lime in São Paulo and Minas Gerais States, Brazil. To characterize and quantify CSD damage, fruit yield and quality were assessed in each combination of sweet orange cultivar (Hamlin, Pera, Natal, and Valencia), age class (3 to 5, 6 to 10, and 11 to 15 years old), and CSD severity class (0 = no symptom, 1 = initial symptoms, and 2 = severe symptoms). For each combination, 10 trees were harvested and 20 fruit were taken for quality analysis. Damage was characterized by reduc_ tion of: (i) total weight of fruit/tree (36 and 67% for severity class 1 and 2, respectively), (ii) number of fruit/tree (27 and 55%), (iii) fruit size (13 and 25% in diameter and height [stem to styler distance]), (iv) fruit weight (32 and 56%), (v) total soluble solids (TSS)/fruit (18 and 42%), and increase of (vi) Brix (14 and 34%), (vii) acidity (16 and 41%), and (viii) TSS/90-1b. box (21 and 33%). There was no alteration on Brix/acidity ratio and percentage of juice on fruit of affected trees. Sweet orange cultivars did not differ in percentage of reduction or increase of all yield and quality variables, with the exception of Pera, which expressed increases of Brix and acidity. For more severe affected trees, the youngest plants showed a higher reduction in fruit number/tree, whereas plants 6 to 10 years old showed a higher increase in fruit acidity and TSS/box. However, no differences in percentage of reduction or increase for other variables were observed among different age classes. The damage to the above probably was associated with reduced water absorption capacity of CSD-affected trees.

Reúso de água no processamento de jeans na indústria têxtil

This study aims to assess the potential for industrial reuse of textile wastewater, after passing through a physical and chemical pretreatment, into denim washing wet processing operations in an industrial textile laundry, with no need for complementary treatments and dilutions. The methodology and evaluation of the proposed tests were based on the production techniques used in the company and upgraded for the experiments tested. The characterization of the treated effluent for 16 selected parameters and the development of a monitoring able to tailor the treated effluent for final disposal in accordance with current legislation was essential for the initiation of testing for reuse. The parameters color, turbidity, SS and pH used were satisfactory as control variables and presents simple determination methods. The denim quality variables considered were: color, odor, appearance and soft handle. The tests were started on a pilot scale following complexity factors attributed to the processes, in denim fabric and jeans, which demonstrated the possibility of reuse, because there was no interference in the processes and at quality of the tested product. Industrial scale tests were initiated by a step control that confirmed the methodology efficiency applied to identify the possibility of reuse by tests that precede each recipe to be processed. 556 replicates were performed in production scale for 47 different recipes of denim washing. The percentage of water reuse was 100% for all processes and repetitions performed after the initial adjustment testing phase. All the jeans were framed with the highest quality for internal control and marketed, being accepted by contractors. The full-scale use of treated wastewater, supported by monitoring and evaluation and control methodology suggested in this study, proved to be valid in textile production, not given any negative impact to the quality the produced jeans under the presented conditions. It is believed that this methodology can be extrapolated to other laundries to determine the possibility of reuse in denim washing wet processing with the necessary modifications to each company.

Possible effects of sodium chloride treatment on quality of effluents from Alabama channel Catfish ponds

Channel catfish ponds are treated with salt (sodium chloride) to increase chloride concentration and prevent nitrite toxicity in fish. A survey indicated that most farmers try to maintain chloride concentration of 50 to 100 mg/L in ponds by annual salt applications. Averages and standard deviations for selected water quality variables in salt-treated ponds were as follows: chloride, 87.2 ± 37.5 mg/L; total dissolved solids (TDS), 336 ± 96 mg/L; specific conductance, 512 ± 164 μmhos/cm. Maximum values were 189 mg/L for chloride, 481 mg/L for TDS, and 825 μmhos/cm for specific conductance. Good correlations between specific conductance values and both chloride and TDS concentrations suggest that specific conductance can be a rapid method for estimating concentrations of these two variables in surface water. The maximum limit for chloride concentration in Alabama streams allowed by the Alabama Department of Environmental Management is 230 mg/L. The usual recommended upper limit of TDS for protection of aquatic life in freshwater streams is 1,000 mg/L. Based on the observed relationship between TDS concentration and specific conductance in Alabama catfish ponds, 1,000 mg/L TDS corresponds to 1,733 μmhos/cm specific conductance. It is unlikely that effluents from salt-treated catfish ponds would violate the in-stream chloride standard of 230 mg/L or harm aquatic life in streams. Nevertheless, chloride concentrations in ponds should be measured before salt application as a safe guard against excessive salt application and chloride concentrations above the in-stream chloride standard.

Blood and seminal plasma concentrations of selenium, zinc and testosterone and their relationship to sperm quality and testicular biometry in domestic cats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chances and risks of publication of quality data - the perspectives of Swiss physicians and nurses

Background The release of quality data from acute care hospitals to the general public is based on the aim to inform the public, to provide transparency and to foster quality-based competition among providers. Due to the expected mechanisms of action and possibly the adverse consequences of public quality comparison, it is a controversial topic. The perspective of physicians and nurses is of particular importance in this context. They are mainly responsible for the collection of quality-control data, and are directly confronted with the results of public comparison. The research focus of this qualitative study was to discover what the views and opinions of the Swiss physicians and nurses were regarding these issues. It was investigated as to how the two professional groups appraised the opportunities as well as the risks of the release of quality data in Switzerland. Methods A qualitative approach was chosen to answer the research question. For data collection, four focus groups were conducted with physicians and nurses who were employed in Swiss acute care hospitals. Qualitative content analysis was applied to the data. Results The results revealed that both occupational groups had a very critical and negative attitude regarding the recent developments. The perceived risks were dominating their view. In summary, their main concerns were: the reduction of complexity, the one-sided focus on measurable quality variables, risk selection, the threat of data manipulation and the abuse of published information by the media. An additional concern was that the impression is given that the complex construct of quality can be reduced to a few key figures, and it that it is constructed from a false message which then influences society and politics. This critical attitude is associated with the different value system and the professional self-concept that both physicians and nurses have, in comparison to the underlying principles of a market-based economy and the economic orientation of health care business. Conclusions The critical and negative attitude of Swiss physicians and nurses must, under all conditions, be heeded to and investigated regarding its impact on work motivation and identification with the profession. At the same time, the two professional groups are obligated to reflect upon their critical attitude and take a proactive role in the development of appropriate quality indicators for the publication of quality data in Switzerland.

An evaluation of a Lake Houston tributary, Cypress Creek, for contamination and water quality

Introduction. Lake Houston serves as a reservoir for both recreational and drinking water for residents of Houston, Texas, and the metropolitan area. The Texas Commission on Environmental Quality (TCEQ) expressed concerns about the water quality and increasing amounts of pathogenic bacteria in Lake Houston (3). The objective of this investigation is to evaluate water quality for the presence of bacteria, nitrates, nitrites, carbon, phosphorus, dissolved oxygen, pH, turbidity, suspended solids, dissolved solids, and chlorine in Cypress Creek. The aims of this project are to analyze samples of water from Cypress Creek and to render a quantitative and graphical representation of the results. The collected information will allow for a better understanding of the aqueous environment in Cypress Creek.^ Methods. Water samples were collected in August 2009 and analyzed in the field and at UTSPH laboratory by spectrophotometry and other methods. Mapping software was utilized to develop novel maps of the sample sites using coordinates attained with the Global Positioning System (GPS). Sample sites and concentrations were mapped using Geographic Information System (GIS) software and correlated with permitted outfalls and other land use characteristic.^ Results. All areas sampled were positive for the presence of total coliform and Escherichia coli (E. coli). The presences of other water contaminants varied at each location in Cypress Creek but were under the maximum allowable limits designated by the Texas Commission on Environmental Quality. However, dissolved oxygen concentrations were elevated above the TCEQ limit of 5.0 mg/L at majority of the sites. One site had near-limit concentration of nitrates at 9.8 mg/L. Land use above this site included farm land, agricultural land, golf course, parks, residential neighborhoods, and nine permitted TCEQ effluent discharge sites within 0.5 miles upstream.^ Significance. Lake Houston and its tributary, Cypress Creek, are used as recreational waters where individuals may become exposed to microbial contamination. Lake Houston also is the source of drinking water for much of Houston/Harris and Galveston Counties. This research identified the presence of microbial contaminates in Cypress Creek above TCEQ regulatory requirements. Other water quality variables measured were in line with TCEQ regulations except for near-limit for nitrate at sample site #10, at Jarvis and Timberlake in Cypress Texas.^

Influence of Crop Load on Tree Growth, Yield, and Fruit Quality of Scab Resistant Apples at Harvest

Apple scab, caused by Venturia inaequalis, is a major disease affecting apple production. Breeding programs have developed over 30 releases of scab-resistant cultivars since 1970 with recent ones having much improved quality. Redfree and GoldRush are from a cooperative breeding program involving Purdue, Rutgers, and Illinois universities while Liberty was introduced from the Cornell University breeding program. For these cultivars to gain better acceptance, more information is needed on their cropping capacities and the effect of crop load on fruit quality attributes. Our study was conducted to determine the relationship between increasing crop load on tree growth, fruit size, and fruit quality variables of the three cultivars under Iowa conditions.

Influence of nutritional and management practices on productive performance and egg quality of brown egg-laying hens = Influencia de factores nutricionales y de manejo sobre la productividad y calidad del huevo en gallinas ponedoras rubias

El objetivo general de esta Tesis Doctoral fue estudiar la influencia de diversos factores nutricionales y de manejo sobre la productividad y la calidad del huevo en gallinas ponedoras comerciales rubias. Los factores estudiados fueron: 1) Cereal principal y tipo de grasa en la dieta; 2) Nivel de proteína bruta y grasa en la dieta; 3) Nivel energético de la dieta; 4) Peso vivo al inicio del período de puesta. En el experimento 1, la influencia del cereal principal en la dieta y el tipo de grasa suplementada en la dieta sobre los parámetros productivos y la calidad del huevo fue estudiado en 756 gallinas rubias de la estirpe Lohmann desde la sem 22 hasta las 54 de vida. El experimento se realizó mediante un diseño completamente al azar con 9 tratamientos ordenados factorialmente, con 3 cereales bases (maíz, trigo blando y cebada) y 3 tipos de grasa que variaban en su contenido en ácido linoléico (aceite de soja, oleína vegetal mezcla y manteca). Todas las dietas satisfacian las recomendaciones nutricionales para gallinas ponedoras rubias según el NRC (1994) y FEDNA (2008). La unidad experimental fue la jaula para todas las variables. Cada tratamiento fue replicado 4 veces, y la unidad experimental estuvo formada por 21 gallinas alojadas en grupos de 7. Las dietas fueron formuladas con un contenido nutritivo similar, excepto para el ácido linoléico, que varió en función del tipo de cereal y grasa utilizado. Así, dependiendo de la combinación de estos elementos el contenido de este ácido graso varió desde un 0.8% (dieta trigo-manteca) a un 3.4% (dieta maíz-aceite de soja). Este rango de ácido linoléico permitió estimar el nivel mínimo de este nutriente en el pienso que permite maximizar el peso del huevo. Los parámetros productivos y la calidad del huevo se controlaron cada 28 días y el peso de las aves se midió individualmente al inicio y al final del experimento con el objetivo de estudiar la variación en el peso vivo de los animales. No se observaron interacciones entre el tipo de cereal y grasa en la dieta para ninguna de las variables productivas estudiadas. Los tratamientos experimentales no afectaron a las principales variables productivas (porcentaje de puesta, peso del huevo y masa de huevo). Sin embargo, la ganancia de peso fue mayor en gallinas alimentadas con maíz o trigo que las gallinas alimentadas con cebada (243 vs. 238 vs. 202 g, respectivamente; P< 0.05). En el mismo sentido, las gallinas alimentadas con manteca obtuvieron una mayor ganancia de peso que las gallinas alimentadas con aceite de soja u oleína vegetal (251 vs. 221 vs. 210 g, respectivamente; P< 0.05). En cuanto a las variables estudiadas en relación con la calidad del huevo, ninguna de las variables estudiadas se vio afectada por el tratamiento experimental, salvo la pigmentación de la yema. Así, las gallinas alimentadas con maíz como cereal principal obtuvieron una mayor puntuación en relación con la escala de color que las gallinas alimentadas con trigo y con cebada (9.0 vs. 8.3 vs. 8.3, respectivamente; P< 0.001). La pigmentación de la yema también se vio afectada por el tipo de grasa en la dieta, así, las gallinas alimentadas con manteca obtuvieron una mayor puntuación de color en relación con la escala de color que las gallinas alimentadas con aceite de soja u oleína vegetal (8.9 vs. 8.5 vs. 8.2, respectivamente; P< 0.001). La influencia del contenido en ácido linoléico respecto al peso de huevo y masa de huevo fue mayor a medida que el contenido de dicho ácido graso se redujo en la dieta. Así, la influencia de la dieta en los radios peso de huevo/g linoléico ingerido y masa de huevo/g linoléico ingerido fue significativamente mayor a medida que el contenido en dicho ácido graso disminuyo en la dieta (P< 0.001). Los resultados del ensayo indican que las gallinas ponedoras rubias no necesitan más de un 1.0% de ácido linoléico en la dieta para maximizar la producción y el tamaño del huevo. Además, se pudo concluir que los 3 cereales y las 3 grasas utilizadas pueden sustituirse en la dieta sin ningún perjuicio productivo o referente a la calidad del huevo siempre que los requerimientos de los animales sean cubiertos. En el experimento 2, la influencia del nivel de proteína bruta y el contenido de grasa de la dieta sobre los parámetros productivos y la calidad del huevo fue estudiado en 672 gallinas ponedoras rubias de la estirpe Lohmann entre las sem 22 y 50 de vida. El experimento fue conducido mediante un diseño completamente al azar con 8 tratamientos ordenados factorialmente con 4 dietas y 2 pesos vivos distintos al inicio de puesta (1592 vs. 1860g). Tres de esas dietas diferían en el contenido de proteína bruta (16.5%, 17.5% y 18.5%) y tenían un contenido en grasa añadida de 1.8%. La cuarta dieta tenía el nivel proteico más elevado (18.5%) pero fue suplementada con 3.6% de grasa añadida en vez de 1.8%. Cada tratamiento fue replicado 4 veces y la unidad experimental consistió en 21 gallinas alojadas dentro de grupos de 7 animales en 3 jaulas contiguas. Todas las dietas fueron isocalóricas (2750 kcal EMAn/kg) y cubrieron las recomendaciones en aminoácidos para gallinas ponedoras rubias (Arg, Ile, Lys, Met, Thr, Trp, TSAA y Val) según el NRC (1994) y FEDNA (2008). Los efectos de los tratamientos sobre las variables productivas y la calidad de huevo fueron estudiados cada 28 días. La dieta no afecto a ninguna de las variables productivas estudiadas a lo largo del período productivo. Sin embargo, el peso inicial origino que las gallinas pesadas consumieran más (120.6 vs. 113.9 g; P< 0.001), obtuvieran un porcentaje de puesta mayor (92.5 vs. 89.8%; P< 0.01) y un peso del huevo mayor (64.9 vs. 62.4 g; P< 0.001) que las gallinas ligeras. El peso inicial de las gallinas no afecto al IC por kg de huevo ni a la mortalidad, sin embargo, la ganancia de peso fue mayor (289 vs. 233 g; P< 0.01) y el IC por docena de huevos fue mejor (1.52 vs. 1.57; P< 0.01) en las gallinas ligeras que en las gallinas pesadas. En cuanto a la calidad del huevo, la dieta no influyó sobre ninguna de las variables estudiadas. Los resultados del ensayo muestran que las gallinas ponedoras rubias, independientemente de su peso vivo al inicio de la puesta, no necesitan una cantidad de proteína bruta superior a 16.5% para maximizar la producción, asegurando que las dietas cubren los requerimientos en AA indispensables. Asimismo, se puedo concluir que las gallinas con un peso más elevado al inicio de puesta producen más masa de huevo que las gallinas con un peso más bajo debido a que las primeras producen más cantidad de huevos y más pesados. Sin embargo, ambos grupos de peso obtuvieron el mismo IC por kg de huevo y las gallinas más livianas en peso obtuvieron un mejor IC por docena de huevo que las pesadas. En el experimento 3 la influencia de la concentración energética sobre los parámetros productivos y la calidad del huevo fue estudiada en 520 gallinas ponedoras rubias de la estirpe Hy-Line en el período 24-59 sem de vida. Se utilizaron 8 tratamientos ordenados factorialmente con 4 dietas que variaron en el contenido energético (2650, 2750, 2850 y 2950 kcal EMAn/kg) y 2 pesos vivos distintos al inicio del período de puesta (1733 vs. 1606g). Cada tratamiento fue replicado 5 veces y la unidad experimental consistió en una jaula con 13 aves. Todas las dietas se diseñaron para que tuvieran una concentración nutritiva similar por unidad energética. Las variables productivas y de calidad de huevo se estudiaron mediante controles cada 28 días desde el inicio del experimento. No se observaron interacciones entre el nivel energético y el peso inicial del ave para ninguna de las variables estudiadas. Un incremento en la concentración energética de la dieta incrementó la producción de huevos (88.8 % vs. 91.2 % vs. 92.7 % vs. 90.5 %), masa de huevo (56.1 g/d vs. 58.1 g/d vs. 58.8 g/d vs. 58.1 g/d), y eficiencia energética (5.42 vs. 5.39 vs. 5.38 vs. 5.58 kcal EMA/g huevo) de forma lineal y cuadrática (P< 0.05) y afectó significativamente a la ganancia de peso (255 g vs. 300 g vs. 325 g vs. 359 g; P<0.05) . Sin embargo, un incremento en la concentración energética provocó un descenso lineal en el consumo de los animales (115 g vs. 114 g vs. 111 g vs. 110 g; P< 0.001) y un descenso lineal y cuadrático en el IC por kg de huevo (2.05 vs. 1.96 vs. 1.89 vs. 1.89; P< 0.01). En cuanto a la calidad del huevo, un incremento en el contenido energético de la dieta provocó una reducción en la calidad del albumen de forma lineal en forma de reducción de Unidades Haugh (88.4 vs. 87.8 vs. 86.3 vs. 84.7; P< 0.001), asimismo el incremento de energía redujo de forma lineal la proporción relativa de cáscara en el huevo (9.7 vs. 9.6 vs. 9.6 vs. 9.5; P< 0.001). Sin embargo, el incremento energético propició un incremento lineal en la pigmentación de la yema del huevo (7.4 vs. 7.4 vs. 7.6 vs. 7.9; P< 0.001). El peso vivo al inicio de la prueba afecto a las variables productivas y a la calidad del huevo. Así, los huevos procedentes de gallinas pesadas al inicio de puesta tuvieron una mayor proporción de yema (25.7 % vs. 25.3 %; P< 0.001) y menor de albumen (64.7 vs. 65.0; P< 0.01) y cáscara (9.5 vs. 9.6; P< 0.05) respecto de los huevos procedentes de gallinas ligeras. Consecuentemente, el ratio yema:albumen fue mayor (0.40 vs. 0.39; P< 0.001) para las gallinas pesadas. Según los resultados del experimento se pudo concluir que las actuales gallinas ponedoras rubias responden con incrementos en la producción y en la masa del huevo a incrementos en la concentración energética hasta un límite que se sitúa en 2850 kcal EMAn/kg. Asimismo, los resultados obtenidos entre los 2 grupos de peso al inicio de puesta demostraron que las gallinas pesadas al inicio de puesta tienen un mayor consumo y producen huevos más pesados, con el consecuente aumento de la masa del huevo respecto de gallinas más ligeras. Sin embargo, el IC por kg de huevo fue el mismo en ambos grupos de gallinas y el IC por docena de huevo fue mejor en las gallinas ligeras. Asimismo, la eficiencia energética fue mejor en las gallinas ligeras. Abstract The general aim of this PhD Thesis was to study the influence of different nutritional factors and management on the productivity and egg quality of comercial Brown laying hens. The factor studied were: 1) The effect of the main cereal and type of fat of the diet; 2) The effect of crude protein and fat content of the diet; 3) The effect of energy concentration of the diet; 4) The effect of initial body weight of the hens at the onset of lay period. In experiment 1, the influence of the main cereal and type of supplemental fat in the diet on productive performance and egg quality of the eggs was studied in 756 Lohmann brown-egg laying hens from 22 to 54 wk of age. The experiment was conducted as a completely randomized design with 9 treatments arranged factorially with 3 cereals (dented corn, soft wheat, and barley) and 3 types of fat (soy oil, acidulated vegetable soapstocks, and lard). Each treatment was replicated 4 times (21 hens per replicate). All diets were formulated according to NRC (1994) and FEDNA (2008) to have similar nutrient content except for linoleic acid that ranged from 0.8 (wheat-lard diet) to 3.4% (corn-soy bean oil) depending on the combination of cereal and fat source used. This approach will allow to estimate the minimum level of linoleic acid in the diets that maximizes egg weight. Productive performance and egg quality traits were recorded every 28 d and BW of the hens was measured individually at the beginning and at the end of the experiment. No significant interactions between main factors were detected for any of the variables studied. Egg production, egg weight, and egg mass were not affected by dietary treatment. Body weight gain was higher (243 vs. 238 vs. 202 g; P<0.05) for hens fed corn or wheat than for hens fed barley and also for hens fed lard than for hens fed soy oil or acidulated vegetable soapstocks (251 vs. 221 vs. 210 g; P< 0.05). Egg quality was not influenced by dietary treatment except for yolk color that was greater (9.0 vs. 8.3 vs. 8.3; P< 0.001) for hens fed corn than for hens fed wheat or barley and for hens fed lard than for hens fed soy oil or acidulated vegetable soapstocks (8.9 vs. 8.5 vs. 8.2, respectivamente; P< 0.001). The influence of linoleic acid on egg weight and egg mass was higher when the fatty acid was reduced in the diet. Thus, the influence of the diet in egg weight/g linoleic acid intake and egg mass/g linolec acid intake was higher when the amount of this fatty acid decreased in the diet (P< 0.001). It is concluded that brown egg laying hens do not need more than 1.0% of linoleic acid in the diet (1.16 g/hen/d) to maximize egg production and egg size. The 3 cereals and the 3 fat sources tested can replace each other in the diet provided that the linoleic acid requirements to maximize egg size are met. In experiment 2, the influence of CP and fat content of the diet on performance and egg quality traits was studied in 672 Lohmann brown egg-laying hens from 22 to 50 wk of age. The experiment was conducted as a completely randomized design with 8 treatments arranged factorially with 4 diets and 2 initial BW of the hens (1,592 vs. 1,860 g). Three of these diets differed in the CP content (16.5, 17.5, and 18.5%) and included 1.8% added fat. The fourth diet had also 18.5% CP but was supplemented with 3.6% fat instead of 1.8% fat. Each treatment was replicated 4 times and the experimental unit consisted of 21 hens allocated in groups of 7 in 3 adjacent cages. All diets were isocaloric (2,750 kcal AME/kg) and met the recommendations of brown egg-laying hens for digestible Arg, Ile, Lys, Met, Thr, Trp, TSAA, and Val. Productive performance and egg quality were recorded by replicate every 28-d. For the entire experimental period, diet did not affect any of the productive performance traits studied but the heavier hens had higher ADFI (120.6 vs. 113.9g; P< 0.001), egg production (92.5 vs. 89.8%; P< 0.01), and egg weight (64.9 vs. 62.4g; P< 0.001) than the lighter hens. Initial BW did not affect feed conversion per kilogram of eggs or hen mortality but BW gain was higher (289 vs. 233g; P< 0.01) and FCR per dozen of eggs was better (1.52 vs. 1.57; P< 0.01) for the lighter than for the heavier hens. None of the egg quality variables studied was affected by dietary treatment or initial BW of the hens. It is concluded that brown egg-laying hens, irrespective of their initial BW, do not need more than 16.5% CP to maximize egg production provided that the diet meet the requirements for key indispensable amino acids. Heavier hens produce more eggs that are larger than lighter hens but feed efficiency per kilogram of eggs is not affected. In experiment 3, the influence of AMEn concentration of the diet on productive performance and egg quality traits was studied in 520 Hy-Line brown egg-laying hens differing in initial BW from 24 to 59 wks of age. There were 8 treatments arranged factorially with 4 diets varying in energy content (2,650, 2,750, 2,850, and 2,950 kcal AMEn/kg) and 2 initial BW of the hens (1,733 vs. 1,606 g). Each treatment was replicated 5 times (13 hens per replicate) and all diets had similar nutrient content per unit of energy. No interactions between energy content of the diet and initial BW of the hens were detected for any trait. An increase in energy concentration of the diet increased (linear, P< 0.05; quadratic P< 0.05) egg production (88.8 % vs. 91.2 % vs. 92.7 % vs. 90.5 %), egg mass (56.1 g/d vs. 58.1 g/d vs. 58.8 g/d vs. 58.1 g/d), energy efficiency (5.42 vs. 5.39 vs. 5.38 vs. 5.58 kcal AMEn/g of egg), and BW gain (255 g vs. 300 g vs. 325 g vs. 359 g; P<0.05) but decreased ADFI (115 g vs. 114 g vs. 111 g vs. 110 g; P< linear, P< 0.001) and FCR per kg of eggs (2.05 vs. 1.96 vs. 1.89 vs. 1.89; linear, P< 0.01; quadratic P< 0.01). An increase in energy content of the diet reduced Haugh units (88.4 vs. 87.8 vs. 86.3 vs. 84.7; P< 0.01) and the proportion of shell in the egg (9.7 vs. 9.6 vs. 9.6 vs. 9.5; P< 0.001). Feed intake (114.6 vs. 111.1 g/hen per day), AMEn intake (321 vs. 311 kcal/hen per day), egg weight (64.2 vs. 63.0 g), and egg mass (58.5 vs. 57.0 g) were higher for the heavier than for the lighter hens (P<0.01) but FCR per kg of eggs and energy efficiency were not affected. Eggs from the heavier hens had higher proportion of yolk (25.7 % vs. 25.3 %; P< 0.001) and lower of albumen (64.7 vs. 65.0; P< 0.01) and shell (9.5 vs. 9.6; P< 0.05) than eggs from the lighter hens. Consequently, the yolk to albumen ratio was higher (0.40 vs. 0.39; P< 0.001) for the heavier hens. It is concluded that brown egg-laying hens respond with increases in egg production and egg mass, to increases in AMEn concentration of the diet up to 2,850 kcal/kg. Heavy hens had higher feed intake and produced heavier eggs and more egg mass than light hens. However, energy efficiency was better for the lighter hens.