FEM based Virtual Prototyping and Design of Third Harmonic Excitation System for Low Voltage Brushless Alternators

Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.

Augmented and Virtual Reality techniques for footwear

The use of 3D imaging techniques has been early adopted in the footwear industry. In particular, 3D imaging could be used to aid commerce and improve the quality and sales of shoes. Footwear customization is an added value aimed not only to improve product quality, but also consumer comfort. Moreover, customisation implies a new business model that avoids the competition of mass production coming from new manufacturers settled mainly in Asian countries. However, footwear customisation implies a significant effort at different levels. In manufacturing, rapid and virtual prototyping is required; indeed the prototype is intended to become the final product. The whole design procedure must be validated using exclusively virtual techniques to ensure the feasibility of this process, since physical prototypes should be avoided. With regard to commerce, it would be desirable for the consumer to choose any model of shoes from a large 3D database and be able to try them on looking at a magic mirror. This would probably reduce costs and increase sales, since shops would not require storing every shoe model and the process of trying several models on would be easier and faster for the consumer. In this paper, new advances in 3D techniques coming from experience in cinema, TV and games are successfully applied to footwear. Firstly, the characteristics of a high-quality stereoscopic vision system for footwear are presented. Secondly, a system for the interaction with virtual footwear models based on 3D gloves is detailed. Finally, an augmented reality system (magic mirror) is presented, which is implemented with low-cost computational elements that allow a hypothetical customer to check in real time the goodness of a given virtual footwear model from an aesthetical point of view.

Liikesimulaattorialustan kehittäminen virtuaaliprototyypin avulla

Työn tarkoituksena oli kehittää kuuden vapausasteen liikesimulaattorialusta virtuaaliprototyypin avulla siten, että alustan dynamiikka mallinnetaan Adams-ohjelmistolla ja ohjaus- ja säätöpiiri Matlab Simulink:llä. Tarkoituksena oli tutkia dynaamisen mallin ja säätöteknisen mallin yhdistämistä ja niiden yhteen toimimista. Tarkoituksena oli myös selvittää tulevaisuudessa rakennettavan Stewart:n alustan mekaniikan mitat ja hydraulikomponenttien koot. Työssä tutkittiin alustan käyttäytymistä halutulla liikealueella, nopeuksia joita saavutetaan ja mekaanisia rajoitteita. Työn tuloksesta on tarkoitus rakentaa fyysinen prototyyppi liittyen KONSI-projektiin, jossa kehitetään satamanosturisimulaattori nosturiohjaajan koulutuksen tueksi. Malli tullaan kytkemään Teppo Lehtisen diplomityönä tehtyyn satamanosturi kontin simulointimalliin ja koko järjestelmän on tarkoitus toimia reaaliaikaisena.

In-Vessel Penetrator -käärmerobotin mallinnus ADAMS-ohjelmistolla

Työn tavoitteena oli muodostaa virtuaaliprototyyppi fuusioreaktorin huollossa käytettävästä IVP-robotista. Työssä mallinnettiin robotin mekaniikka joustavana sekä toimilaitteiden ja käyttöjen dynaamiset ominaisuudet valmistajien esitietojen ja mitoitustietojen perusteella. Käyttöjen ja mekaniikan mallit yhdistettiin ADAMS-ohjelmistossa. Mekaanisten joustojen mallinnuksessa sekä verifioinnissa käytettiin apuna ANSYS –ohjelmistoa. Virtuaaliprototyypin toimivuudesta varmistuttiin vertaamalla sitä robotin suunnittelutietoihin ja fyysiseen prototyyppiin. Robotin ohjauksessa käytettävän P-säätäjän vaikutusta tutkittiin eri vahvistuksen arvoilla sekä verrattiin mekaanisia vasteita fyysisen prototyypin dynaamisiin testeihin. Esimerkkinä robotin käyttäytymisestä todellisessa tilanteessa simuloitiin sen ajoa reaktoriin. Toteutetun simulointimallin todettiin vastaavan rakenteeltaan sekä siinä esiintyvien voimien osalta suunnitelmien mukaista konstruktiota. Käytetyillä parametreilla se toteutti hyvin robotille asetetut nopeusvaatimukset.

Siltanosturin mallinnusmenetelmien kehittäminen

Työn tarkoituksena oli selvittää kaupallisen dynamiikan simulointiohjelmiston (Adams) soveltuvuus siltanosturin mallintamiseen. Työn kohteena oli kaksipalkkinen siltanosturi, joka sijaitsi KCI:n tiloissa Hyvinkäällä. Nosturin jänneväli oli noin 19.5 metriä ja nostokyky 16 tonnia. Mallintamisessa keskityttiin nosturin dynamiikkaan sekä ohjausvoimiin nosturin kantopyörissä. Simulointitulokset verifioitiin mittauksin. Koska mallista haluttiin mahdollisimman yksinkertainen, mallinnettiin ainoastaan pääkannattajat ja köydet joustavina. Muut osat mallinnettiin jäykkinä. Yksinkertaisuuteen pyrittiin sen vuoksi, että mallia oli tarkoitus käyttää perustana komponenttikirjaston luomiseksi myöhempää käyttöä varten. Tuloksista todettiin mallin soveltuvan hyvin nosturin dynamiikan mallintamiseen. Mallista saatavat tulokset vastasivat hyvin mitattuja liikkeitä. Ohjausvoimia ei kuitenkaan saatu verifioitua. Käytetty mittausmenetelmä osoittautui sopimattomaksi.

DFM(A)- aspects for an sma connector design

In this research, manufacturability analysis is made for an SMA connector. Analysis and aspects of applying virtual prototyping for an SMA connector design and manufacturing are also investigated. Special questionnaires for the component and machining are made in order to enable necessary information to ensure DFM(A) –aspects of products. The aspects of easy manufacturing for machining the SMA connector are collected. Material selection is discussed, and manufacturing stages of prototype manufacturing are presented. The main focus of this research is on prototype manufacturing, but also aspects considering volume production are discussed. A special purpose SMA connector is designed for printed circuit board edge mounting.

Design and development of the architecture of an agricultural mobile robot

Parameters such as tolerance, scale and agility utilized in data sampling for using in Precision Agriculture required an expressive number of researches and development of techniques and instruments for automation. It is highlighted the employment of methodologies in remote sensing used in coupled to a Geographic Information System (GIS), adapted or developed for agricultural use. Aiming this, the application of Agricultural Mobile Robots is a strong tendency, mainly in the European Union, the USA and Japan. In Brazil, researches are necessary for the development of robotics platforms, serving as a basis for semi-autonomous and autonomous navigation systems. The aim of this work is to describe the project of an experimental platform for data acquisition in field for the study of the spatial variability and development of agricultural robotics technologies to operate in agricultural environments. The proposal is based on a systematization of scientific work to choose the design parameters utilized for the construction of the model. The kinematic study of the mechanical structure was made by the virtual prototyping process, based on modeling and simulating of the tension applied in frame, using the.

Sähköajoneuvon sähkökäytön ja mekaniikan reaaliaikaisen yhdistelmäsimulaation toteuttaminen virtuaaliympäristössä

Esitetyn tutkimuksen tavoite on selvittää yksinkertaisen sähköajoneuvosimulaation avulla sähkökäyttösimulaation ja mekaniikkasimulaation välisen ohjelmallisen rajapinnan toimivuutta ja samalla toteuttaa LUT Energian hybridilaboratorion ensimmäinen rajapintaa hyödyntävä sähkökäytön ja mekaniikan yhdistelmäsimulaatio. Tutkimus on osa Lappeenrannan teknillisen yliopiston hybridikäyttötutkimusta, jossa muun muassa virtuaalisimuloinnin ja in-loop –simulaatioiden avulla tutkitaan raskaiden työkoneiden hybridisoinnin vaikutuksia esimerkiksi niiden suorituskykyyn, energiatehokkuuteen ja käytettävyyteen. Tulokset osoittavat mainitun rajapinnan toimivuuden, mikä mahdollistaa tutkimuksen etenemisen. Lisäksi raportti selvittää virtuaalisimuloinnin keskeisiä käsitteitä (virtual prototyping, hardware-in-the-loop sekä human-in-the-loop –simulointi).

Evaluation of sensor configurations for robotic surgical instruments

Designing surgical instruments for robotic-assisted minimally-invasive surgery (RAMIS) is challenging due to constraints on the number and type of sensors imposed by considerations such as space or the need for sterilization. A new method for evaluating the usability of virtual teleoperated surgical instruments based on virtual sensors is presented. This method uses virtual prototyping of the surgical instrument with a dual physical interaction, which allows testing of different sensor configurations in a real environment. Moreover, the proposed approach has been applied to the evaluation of prototypes of a two-finger grasper for lump detection by remote pinching. In this example, the usability of a set of five different sensor configurations, with a different number of force sensors, is evaluated in terms of quantitative and qualitative measures in clinical experiments with 23 volunteers. As a result, the smallest number of force sensors needed in the surgical instrument that ensures the usability of the device can be determined. The details of the experimental setup are also included.

Work and technological innovation in organic agriculture

Organic agriculture is a sustainable cultivation ecologically, economically and socially. Several researches in organic agriculture have been made from technical perspectives, economic traits or related to ecological aspects. There are practically no investigations into the nature of the technology used in organic agriculture, especially from an ergonomic perspective. From the activity analysis, this study aimed to map the technology used in the production of organic vegetables. Properties producing organic vegetables were selected representing the State of São Paulo. It was applied an instrument (questionnaire and semi-structured interview) with their managers and it was made visual records to identify adaptations, innovations and technological demands that simultaneously minimize the workload and the difficulties in performing the tasks and increase work productivity. For some of the technological innovations a digital scanner was used to generate a virtual solid model to facilitate its redesign and virtual prototyping. The main results show that organic farmers have little technology in product form. The main innovations that enable competitive advantage or allow higher labor productivity occur in the form of processes, organization and marketing.

Metodologia de design mediada por protótipos

Pós-graduação em Design - FAAC

Work and technological innovation in organic agriculture

Organic agriculture is a sustainable cultivation ecologically, economically and socially. Several researches in organic agriculture have been made from technical perspectives, economic traits or related to ecological aspects. There are practically no investigations into the nature of the technology used in organic agriculture, especially from an ergonomic perspective. From the activity analysis, this study aimed to map the technology used in the production of organic vegetables. Properties producing organic vegetables were selected representing the State of Sao Paulo. It was applied an instrument (questionnaire and semi-structured interview) with their managers and it was made visual records to identify adaptations, innovations and technological demands that simultaneously minimize the workload and the difficulties in performing the tasks and increase work productivity. For some of the technological innovations a digital scanner was used to generate a virtual solid model to facilitate its redesign and virtual prototyping. The main results show that organic farmers have little technology in product form. The main innovations that enable competitive advantage or allow higher labor productivity occur in the form of processes, organization and marketing.

Modelle und Prototypen für die Medizin

Der Anwendungsbereich für Modelle und Prototypen hat sich mittlerweile auch auf unterschiedlichste medizinische Fragestellungen ausgedehnt. Der vorliegende Beitrag zeigt an verschiedenen Praxisbeispielen und Verfahren Möglichkeiten eines in der Technik etablierten Verfahrens für eine erweiterte Anwendung auf.