Stückgutförderung von Mikroteilen mit der Schwingrinne

Der vorliegende Beitrag greift das Auftreten von Größeneffekten auf, welche auf dem WGTL-Kolloquium 2006 vorgestellt worden sind und nun Gegenstand tiefer gehender Forschung sind. Dabei handelt es sich um einen Wechsel von Sekundäreffekten zu Primäreffekten, ausgelöst durch das Downscaling der Bauteildimensionen und somit eines veränderten Verhältnisses von der Masse zur Oberfläche. Es werden erste Ergebnisse aus der Abschätzung der Kräfte vorgestellt, und die Auswirkungen dieser Kräfte auf den Fördervorgang diskutiert.

Determining heavy vehicle suspension health from vibratory wheel loads

A low-cost test bed was made from a modified heavy vehicle (HV) brake tester. By rotating a test HV’s wheel on an eccentric roller, a known vibration was imparted to the wheel under test. A control case for dampers in good condition was compared with two test cases of ineffective shock absorbers. Measurement of the forces at the bearings of the roller provided an indication of the HV wheel-forces. Where the level of serviceability of the shock absorbers varied, differences in wheel load provided a quality indicator corresponding to a change of damper characteristic. Conclusions regarding the levels of damper maintenance beyond which HV suspensions cause road damage and dynamic wheel forces at the threshold of tyre wear at which HV shock absorbers are normally replaced are presented.

Design, modelling and simulation of vibratory micromachined gyroscopes

Among various MEMS sensors, a rate gyroscope is one of the most complex sensors from the design point of view. The gyro normally consists of a proof mass suspended by an elaborate assembly of beams that allow the system to vibrate in two transverse modes. The structure is normally analysed and designed using commercial FEM packages such as ANSYS or MEMS specific commercial tools such as Coventor or Intellisuite. In either case, the complexity in analysis rises manyfolds when one considers the etch hole topography and the associated fluid flow calculation for damping. In most cases, the FEM analysis becomes prohibitive and one resorts to equivalent electrical circuit simulations using tools like SABER in Coventor. Here, we present a simplified lumped parameter model of the tuning fork gyro and show how easily it can be implemented using a generic tool like SIMULINK. The results obtained are compared with those obtained from more elaborate and intense simulations in Coventor. The comparison shows that lumped parameter SIMULINK model gives equally good results with fractional effort in modelling and computation. Next, the performance of a symmetric and decoupled vibratory gyroscope structure is also evaluated using this approach and a few modifications are made in this design to enhance the sensitivity of the device.

Hybrid Elements for Modelling Squeeze Film Effects Coupled with Structural Interactions in Vibratory MEMS Devices

We present a hybrid finite element based methodology to solve the coupled fluid structure problem of squeeze film effects in vibratory MEMS devices, such as gyroscopes, RF switches, and 2D resonators. The aforementioned devices often have a thin plate like structure vibrating normally to a fixed substrate, and are generally not perfectly vacuum packed. This results in a thin air film being trapped between the vibrating plate and the fixed substrate which behaves like a squeeze film offering both stiffness and damping. For accurate modelling of such devices the squeeze film effects must be incorporated. Extensive literature is available on squeeze film modelling, however only a few studies address the coupled fluid elasticity problem. The majority of the studies that account for the plate elasticity coupled with the fluid equation, either use approximate mode shapes for the plate or use iterative solution strategies. In an earlier work we presented a single step coupled methodology using only one type of displacement based element to solve the coupled problem. The displacement based finite element models suffer from locking issues when it comes to modelling very thin structures with the lateral dimensions much larger than the plate thickness as is typical in MEMS devices with squeeze film effects. In this work we present another coupled formulation where we have used hybrid elements to model the structural domain. The numerical results show a huge improvement in convergence and accuracy with coarse hybrid mesh as compared to displacement based formulations. We further compare our numerical results with experimental data from literature and find them to be in good accordance.

A novel acoustic-vibratory multimodal duet

The communication strategy of most crickets and bushcrickets typically consists of males broadcasting loud acoustic calling songs, while females perform phonotaxis, moving towards the source of the call. Males of the pseudophylline bushcricket species Onomarchus uninotatus produce an unusually low-pitched call, and we found that the immediate and most robust response of females to the male acoustic call was a bodily vibration, or tremulation, following each syllable of the call. We hypothesized that these bodily oscillations might send out a vibrational signal along the substrate on which the female stands, which males could use to localize her position. We quantified these vibrational signals using a laser vibrometer and found a clear phase relationship of alternation between the chirps of the male acoustic call and the female vibrational response. This system therefore constitutes a novel multimodal duet with a reliable temporal structure. We also found that males could localize the source of vibration but only if both the acoustic and vibratory components of the duet were played back. This unique multimodal duetting system may have evolved in response to higher levels of bat predation on searching bushcricket females than calling males, shifting part of the risk associated with partner localization onto the male. This is the first known example of bushcricket female tremulation in response to a long-range male acoustic signal and the first known example of a multimodal duet among animals.

Comparison between weight loss of bends in a pneumatic conveyor and erosion rate obtained in a centrifugal erosion tester for the same materials

In order to find a link between results obtained from a laboratory erosion tester and tests carried out on a pneumatic conveyor, a comparison has been made between weight loss from bends on an industrial-scale pneumatic conveyor and erosion rates obtained in a small centrifugal erosion tester, for the same materials. Identical test conditions have been applied to both experiments so that comparable test results have been obtained. The erosion rate of mild steel commonly used as the wall material of conveyor pipes and pipe bends was determined individually on both test rigs. A relationship between weight loss from the bends and erosion rate determined from the tester has been developed. A discussion based on the results and their applicability to the prediction of wear in pneumatic conveyors concludes the paper. © 2004 Elsevier B.V. All rights reserved.