Análise dos efeitos das deformações estruturais sobre a transferência transversal de carga em um veículo do tipo fórmula SAE submetido a uma aceleração lateral constante

This paper studies the frame deformations on a formula SAE vehicle in steady-state cornering and its influence on the lateral load transfers and, consequently, on the tires normal loads due to the applied lateral load. For a vehicle with a perfect rigid frame, the vehicle mass, the position of the center of gravity and the suspensions are the only factors responsible for the load distribution between the tires. When the frame deformations are no longer negligible, the frame deformations affect the loaddistribution between the tires. The frame flexibility turns it able to behave as an additional set of springs to the suspension system, thus changing the behavior of the set. This paper describes howit happens and suggests ways to minimize this phenomenon

Fatores críticos de sucesso no processo de desenvolvimento de produtos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos impactos ambientais gerados pelos automóveis na cidade de Ilha Solteira-SP

Pós-graduação em Engenharia Civil - FEIS

Análise cinemática e dinâmica para conversão de um VW saveiro em veículo elétrico

This work aims to kinematic and dynamic analysis of a VW Saveiro in order to estimate the power requested to the engine with the imposed movement conditions. Thus, the study will be the basis to the specification of the electric engine, on the conversion of the internal combustion vehicle into electric one. First of all, a literature review was done in order to understand the state of the art for this issue and come up with the technical features of the vehicle in question. The next step is the identification and calculation of all forces acting on the prototype in motion, from 0 to 120 km/h, in intervals of 10 km/h, under the defined conditions of path and time. Then, were determined the values of the torque and rotation of the components from the transmission system, as well as the engine power, for each speed range. The results show the most influential forces on the resistence of the movement in each speed range, and the behavior of the torque curve is verified. Finally, it was also analyzed the implementation of pinwheels on the frontal area of the vehicle, in order to convert wind energy into electrical energy to supply the lighting subsystem of the vehicle and the proposal was validated. Limiting the maximum speed of the vehicle to 90 km/h, it was finally concluded that the power of the electric engine should be 40 HP

Modellizzazione dinamica di un motore brushless DC per uso propulsivo su droni

Studio e realizzazione di un modello dinamico, in Simulink, del sistema propulsivo di un aeromodello, dotato di un autopilota e di un'elettronica di bordo. Tali caratteristiche consentono al drone di effettuare delle operazioni di volo in piena autonomia.

Quantification of motor vehicle emission factors from on road measurements

Assessment and prediction of the impact of vehicular traffic emissions on air quality and exposure levels requires knowledge of vehicle emission factors. The aim of this study was quantification of emission factors from an on road, over twelve months measurement program conducted at two sites in Brisbane: 1) freeway type (free flowing traffic at about 100 km/h, fleet dominated by small passenger cars - Tora St); and 2) urban busy road with stop/start traffic mode, fleet comprising a significant fraction of heavy duty vehicles - Ipswich Rd. A physical model linking concentrations measured at the road for specific meteorological conditions with motor vehicle emission factors was applied for data analyses. The focus of the study was on submicrometer particles; however the measurements also included supermicrometer particles, PM2.5, carbon monoxide, sulfur dioxide, oxides of nitrogen. The results of the study are summarised in this paper. In particular, the emission factors for submicrometer particles were 6.08 x 1013 and 5.15 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd respectively and for supermicrometer particles for Tora St, 1.48 x 109 particles per vehicle-1 km-1. Emission factors of diesel vehicles at both sites were about an order of magnitude higher than emissions from gasoline powered vehicles. For submicrometer particles and gasoline vehicles the emission factors were 6.08 x 1013 and 4.34 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively, and for diesel vehicles were 5.35 x 1014 and 2.03 x 1014 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively. For supermicrometer particles at Tora St the emission factors were 2.59 x 109 and 1.53 x 1012 particles per vehicle-1 km-1, for gasoline and diesel vehicles, respectively.

A database ATP simulated waveforms of shunt reactor switching cases with vacuum breakers on motor circuits

This paper presents a database ATP (Alternative Transient Program) simulated waveforms for shunt reactor switching cases with vacuum breakers in motor circuits following interruption of the starting current. The targeted objective is to provide multiple reignition simulated data for diagnostic and prognostic algorithms development, but also to help ATP users with practical study cases and component data compilation for shunt reactor switching. This method can be easily applied with different data for the different dielectric curves of circuit-breakers and networks. This paper presents design details, discusses some of the available cases and the advantages of such simulated data.