Obtención del modelo tridimensional de dos fragmentos de globos de lava de la erupción volcánica submarina de La Isla de El Hierro en 2011, mediante sistemas escáner laser 3D.

El objetivo del proyecto consiste en la realización de un modelo tridimensional,mediante la utilización de un equipo laser escáner 3D, de los fragmentos de unos globos de lava emergidos de las erupciones que ocurrieron en la isla canaria de ElHierro, en Octubre de 2011. Se persigue con dicho modelo, conseguir una muestra virtual de unos restos geológicos que, por su naturaleza, son extremadamente frágiles y así permitir que puedan ser estudiados con sus características de la forma más completa posible sin necesidad de ser manipulados incluso cuando las muestras físicas se hayan deteriorado.

Sistema de modelização tridimensional para ambientes não estruturados

A navegação de veículos autónomos em ambientes não estruturados continua a ser um problema em aberto. A complexidade do mundo real ainda é um desafio. A difícil caracterização do relevo irregular, dos objectos dinâmicos e pouco distintos(e a inexistência de referências de localização) tem sido alvo de estudo e do desenvolvimento de vários métodos que permitam de uma forma eficiente, e em tempo real, modelizar o espaço tridimensional. O trabalho realizado ao longo desta dissertação insere-se na estratégia do Laboratório de Sistemas Autónomos (LSA) na pesquisa e desenvolvimento de sistemas sensoriais que possibilitem o aumento da capacidade de percepção das plataformas robóticas. O desenvolvimento de um sistema de modelização tridimensional visa acrescentar aos projectos LINCE (Land INtelligent Cooperative Explorer) e TIGRE (Terrestrial Intelligent General proposed Robot Explorer) maior autonomia e capacidade de exploração e mapeamento. Apresentamos alguns sensores utilizados para a aquisição de modelos tridimensionais, bem como alguns dos métodos mais utilizados para o processo de mapeamento, e a sua aplicação em plataformas robóticas. Ao longo desta dissertação são apresentadas e validadas técnicas que permitem a obtenção de modelos tridimensionais. É abordado o problema de analisar a cor e geometria dos objectos, e da criação de modelos realistas que os representam. Desenvolvemos um sistema que nos permite a obtenção de dados volumétricos tridimensionais, a partir de múltiplas leituras de um Laser Range Finder bidimensional de médio alcance. Aos conjuntos de dados resultantes associamos numa nuvem de pontos coerente e referenciada. Foram desenvolvidas e implementadas técnicas de segmentação que permitem inspeccionar uma nuvem de pontos e classifica-la quanto às suas características geométricas, bem como ao tipo de estruturas que representem. São apresentadas algumas técnicas para a criação de Mapas de Elevação Digital, tendo sido desenvolvida um novo método que tira partido da segmentação efectuada

Caracterização e modelação de fissuras em edifícios utilizando 3D laser scanning, com vista à sua reabilitação

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil

Refinamento geométrico de contornos e cumeeiras de telhados de edifícios extraídos de dados laser com uso de imagem aérea

In this paper, a method is proposed to refine the LASER 3D roofs geometrically by using a high-resolution aerial image and Markov Random Field (MRF) models. In order to do so, a MRF description for grouping straight lines is developed, assuming that each projected side contour and ridge is topologically correct and that it is only necessary to improve its accuracy. Although the combination of laser data with data from image is most justified for refining roof contour, the structure of ridges can give greater robustness in the topological description of the roof structure. The MRF model is formulated based on relationships (length, proximity, and orientation) between the straight lines extracted from the image and projected polygon and also on retangularity and corner injunctions. The energy function associated with MRF is minimized by the genetic algorithm optimization method, resulting in the grouping of straight lines for each roof object. Finally, each grouping of straight lines is topologically reconstructed based on the topology of the corresponding LASER scanning polygon projected onto the image-space. The results obtained were satisfactory. This method was able to provide polygons roof refined buildings in which most of its contour sides and ridges were geometrically improved.

El monasterio de Santa María de Moreruela. Análisis de la patología de los muros y bóvedas de la iglesia.

El objetivo de esta tesis ha sido el análisis de los procesos patológicos de las bóvedas y los muros de la iglesia del monasterio de Santa María de Moreruela (Zamora). Estos procesos comenzaron en el año 1823 pero se acentuaron en la década de 1880 dando lugar a que el Monasterio empezará a desarrollar un estado de ruina progresiva en el corto espacio de tiempo de unos cincuenta años. La tesis, a lo largo de los diez capítulos en que se concreta, trata, de lo general a lo particular, de establecer los criterios de la Arquitectura del Císter y sus elementos constructivos, para conocer en profundidad las bases de diseño del monasterio y después recabar toda la información en la bibliografía y en otros documentos, que existen sobre el Monasterio de Santa María de Moreruela y en particular de su iglesia. Estudiados y analizados, en profundidad, el monasterio y la Iglesia, a través, de la bibliografía y la documentación encontrada, se procede al desarrollo planimétrico de los mismos. Este desarrollo se acomete al “estilo tradicional” y con la técnica del laser 3D. De esta manera se reconstruye en papel el monasterio antes de la ruina, así como algunos elementos constructivos, desaparecidos en la actualidad, posibilitando su reconstrucción en un futuro. Tras los trabajos de representación gráfica se redactan fichas técnicas sobre la patología encontrada en la iglesia y posteriormente se realizan ensayos sobre las piedras: ensayos geomecánicos, de alterabilidad y de resistencia mecánica mediante ultrasonidos; ensayos sobre el terreno mediante sísmica de refracción, así como el ensayo Lambe y el ensayo con el edómetro para clasificar el nivel de expansividad de las arcillas. Todo esto permite concluir, que la causa fundamental de la ruina acelerada que sufrieron la bóveda y los muros la iglesia fue debida, fundamentalmente, a la pérdida de masa de las dovelas, así como al mal funcionamiento de los drenajes que tenían como objetivo aislar de las variaciones de humedad, el terreno de arcillas expansivas, sobre el que apoyan los elementos de cimentación, así como recomendar algunas medidas para preservar los restos.

Surgical planning for resection of an ameloblastoma and reconstruction of the mandible using a selective laser sintering 3D biomodel

Ameloblastoma is a benign locally aggressive infiltrative odontogenic lesion. It is characterized by slow growth and painless swelling. The treatment for ameloblastoma varies from curettage to en bloc resection, and the reported recurrence rates after treatment are high; the safety margin of resection is important to avoid recurrence. Advances in technology brought about great benefits in dentistry; a new generation of computed tomography scanners and 3-dimensional images enhance the surgical planning and management of maxillofacial tumors. The development of new prototyping systems provides accurate 3D biomodels on which surgery can be simulated, especially in cases of ameloblastoma, in which the safety margin is important for treatment success. A case of mandibular follicular ameloblastoma is reported where a 3D biomodel was used before and during surgery.

Building 3D City Models: Testing and Comparing Laser Scanning and Low-Cost UAV Data Using FOSS Technologies

Contém resumo

Does abdominoplasty with liposuction of the love handles yield a shorter scar? An analysis with abdominal 3D laser scanning.

The aim of this study was to evaluate the combination of abdominoplasty with liposuction of both flanks with regards to length of scar, complications, and patient's satisfaction. A retrospective analysis of 35 patients who underwent esthetic abdominoplasty at our institution between 2002 and 2004 was performed. Thirteen patients underwent abdominoplasty with liposuction of both flanks, 22 patients underwent conventional abdominoplasty. Liposuction of the flanks did not increase the rate of complications of the abdominoplasty procedures. We found a tendency toward shorter scars in patients who underwent abdominoplasty combined with liposuction of the flanks. Implementation of 3-dimensional laser surface scanning to objectify the postoperative outcomes, documented a comparable degree of flatness of the achieved body contouring in both procedures. 3-dimensional laser surface scanning can be a valuable tool to objectify assessment of postoperative results.

Comparability of clinical wear measurements by optical 3D laser scanning in two different centers.

OBJECTIVE: The purpose of this study was to compare the use of different variables to measure the clinical wear of two denture tooth materials in two analysis centers. METHODS: Twelve edentulous patients were provided with full dentures. Two different denture tooth materials (experimental material and control) were placed randomly in accordance with the split-mouth design. For wear measurements, impressions were made after an adjustment phase of 1-2 weeks and after 6, 12, 18, and 24 months. The occlusal wear of the posterior denture teeth of 11 subjects was assessed in two study centers by use of plaster replicas and 3D laser-scanning methods. In both centers sequential scans of the occlusal surfaces were digitized and superimposed. Wear was described by use of four different variables. Statistical analysis was performed after log-transformation of the wear data by use of the Pearson and Lin correlation and by use of a mixed linear model. RESULTS: Mean occlusal vertical wear of the denture teeth after 24 months was between 120μm and 212μm, depending on wear variable and material. For three of the four variables, wear of the experimental material was statistically significantly less than that of the control. Comparison of the two study centers, however, revealed correlation of the wear variables was only moderate whereas strong correlation was observed among the different wear variables evaluated by each center. SIGNIFICANCE: Moderate correlation was observed for clinical wear measurements by optical 3D laser scanning in two different study centers. For the two denture tooth materials, wear measurements limited to the attrition zones led to the same qualitative assessment.

Evolution of a debris flow channel monitored using a 3D terrestrial laser scanner

Like numerous torrents in mountainous regions, the Illgraben creek (canton of Wallis, SW Switzerland) produces almost every year several debris flows. The total area of the active catchment is only 4.7 km², but large events ranging from 50'000 to 400'000 m³ are common (Zimmermann 2000). Consequently, the pathway of the main channel often changes suddenly. One single event can for instance fill the whole river bed and dig new several-meters-deep channels somewhere else (Bardou et al. 2003). The quantification of both, the rhythm and the magnitude of these changes, is very important to assess the variability of the bed's cross section and long profile. These parameters are indispensable for numerical modelling, as they should be considered as initial conditions. To monitor the channel evolution an Optech ILRIS 3D terrestrial laser scanner (LIDAR) was used. LIDAR permits to make a complete high precision 3D model of the channel and its surroundings by scanning it from different view points. The 3D data are treated and interpreted with the software Polyworks from Innovmetric Software Inc. Sequential 3D models allow for the determination of the variation in the bed's cross section and long profile. These data will afterwards be used to quantify the erosion and the deposition in the torrent reaches. To complete the chronological evolution of the landforms, precise digital terrain models, obtained by high resolution photogrammetry based on old aerial photographs, will be used. A 500 m long section of the Illgraben channel was scanned on 18th of August 2005 and on 7th of April 2006. These two data sets permit identifying the changes of the channel that occurred during the winter season. An upcoming scanning campaign in September 2006 will allow for the determination of the changes during this summer. Preliminary results show huge variations in the pathway of the Illgraben channel, as well as important vertical and lateral erosion of the river bed. Here we present the results of a river bank on the left (north-western) flank of the channel (Figure 1). For the August 2005 model the scans from 3 viewpoints were superposed, whereas the April 2006 3D image was obtained by combining 5 separate scans. The bank was eroded. The bank got eroded essentially on its left part (up to 6.3 m), where it is hit by the river and the debris flows (Figures 2 and 3). A debris cone has also formed (Figure 3), which suggests that a part of the bank erosion is due to shallow landslides. They probably occur when the river erosion creates an undercut slope. These geometrical data allow for the monitoring of the alluvial dynamics (i.e. aggradation and degradation) on different time scales and the influence of debris flows occurrence on these changes. Finally, the resistance against erosion of the bed's cross section and long profile will be analysed to assess the variability of these two key parameters. This information may then be used in debris flow simulation.

Analysis of Roman pottery graffiti by high resolution capture and 3D laser profilometry

The graffiti on pottery discovered on the site of Aventicum (Avenches, VD/Switzerland) form the largest corpus of minor inscriptions of the Roman Empire studied until now. Indeed, a total of 1828 graffiti have been found. The reading and the recording of the inscriptions are generally dependent on the state of conservation of the graffito and its support. In numerous cases, only a pale shadow of the inscription is visible, which makes traditional observations, such as visual observations with the naked eye, unsuitable for its decipherment. Consequently, advanced techniques have been applied for enhancing the readability of such inscriptions. In our paper we show the efficiency of 3D laser profilometry as well as high resolution photography as powerful means to decipher illegible engraved inscriptions. The use of such analyses to decipher graffiti on pottery or on other materials enables a better understanding of minor inscriptions and improves the knowledge of the daily life of ancient populations substantially.

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels.

Laser stripe peak detector for 3D scanners: a FIR filter approach

The accuracy of a 3D reconstruction using laser scanners is significantly determined by the detection of the laser stripe. Since the energy pattern of such a stripe corresponds to a Gaussian profile, it makes sense to detect the point of maximum light intensity (or peak) by computing the zero-crossing point of the first derivative of such Gaussian profile. However, because noise is present in every physical process, such as electronic image formation, it is not sensitive to perform the derivative of the image of the stripe in almost any situation, unless a previous filtering stage is done. Considering that stripe scanning is an inherently row-parallel process, every row of a given image must be processed independently in order to compute its corresponding peak position in the row. This paper reports on the use of digital filtering techniques in order to cope with the scanning of different surfaces with different optical properties and different noise levels, leading to the proposal of a more accurate numerical peak detector, even at very low signal-to-noise ratios

Applicazione di tecniche Laser a scansione nel rilevamento 3D di provini di conglomerato bituminoso

Obiettivo della tesi, oltre ad una descrizione della tecnica laser a scansione ed alla presentazione di alcune realizzazioni tipiche in ambito terrestre, è relazionare su una esperienza effettuata di recente su una applicazione particolare, il rilievo tridimensionale di campioni di pavimentazioni stradali in conglomerato bituminoso per documentarne la tessitura tramite parametri classici e nuovi indicatori resi possibili dal dato tridimensionale. L’attività di tesi si è concentrata soprattutto nei problemi della fase di acquisizione.

Ricostruzione 3D di oggetti ad alto potere diffusivo mediante triangolazione laser

L'obiettivo principale che questa tesi intende perseguire e la progettazione di un sistema di acquisizione 3D a basso costo basato sul metodo di triangolazione a lama laser. A tale scopo si adotterà una telecamera general-purpose, e si provvederà sia alla realizzazione di un prototipo di sistema di attuazione per automatizzare la scansione dell'oggetto, sia all'implementazione di algoritmi per la calibrazione della geometria laser-telecamera, il rilevamento del profilo laser nell'immagine e la sua successiva ricostruzione 3D, tenendo anche conto delle complicazioni che l'uso di oggetti ad alto potere diffusivo apporta a tale problema, a causa dei marcati effetti di subsurface scattering della luce laser. Il sistema di triangolazione sarà validato caratterizzando, mediante il confronto con pezzi di dimensioni note, la precisione e l'accuratezza delle misurazioni, e valutando i tempi di esecuzione degli algoritmi. Inoltre, le prestazioni ed i risultati delle acquisizioni saranno messi a confronto con quelli ottenuti adottando una telecamera high-end dedicata. Lo studio preliminare svolto in questa sede e propedeutico per la futura realizzazione di un sistema per la ricostruzione in camera bianca di protesi d'osso su misura.