Evaluation of WC-17Co and WC-10Co-4Cr thermal spray coatings by HVOF on the fatigue and corrosion strength of AISI 4340 steel

It is known that chromium electroplating is related to the reduction in the fatigue strength of base metal. However, chromium results in protection against wear and corrosion combined with chemical resistance and good lubricity. Environmental requirements are an important point to be considered in the search for possible alternatives to hard chrome plating. Aircraft landing gear manufactures are considering WC thermal spray coating applied by the high-velocity oxygen-fuel (HVOF) process an alternative candidate, which shows performance at least comparable to results, obtained for hard chrome plating. The aim of this study is to compare the influence of WC-17Co and WC-10Co-4Cr coatings applied by HVOF process and hard chromium electroplating on the fatigue strength of AISI 4340 steel, with and without shot peening. S-N curves were obtained in axial fatigue test for base material, chromium plated and tungsten carbide coated specimens. Tungsten carbide thermal spray coating results in higher fatigue strength when compared to hard chromium electroplated. Shot peening prior to thermal spraying showed to be an excellent alternative to increase fatigue strength of AISI 4340 steel. Experimental data showed higher axial fatigue and corrosion resistance in salt fog exposure for samples WC-10Co-4Cr HVOF coated when compared with WC-17Co. Fracture surface analysis by scanning electron microscopy (SEM) indicated the existence of a uniform coverage of nearly all substrates. (C) 2004 Elsevier B.V. All rights reserved.

Effects of electroplated zinc-nickel alloy coatings on the fatigue strength of AISI 4340 high strength steel

It is well known that fatigue behaviour is an important parameter to be considered in mechanical components subjected to constant and variable amplitude loadings. In combination with corrosion phenomenon, fatigue effects were responsible for proximally 64% of fails that occur in metallic parts of aeronautical accidents in the last 30 years. Recovered substrates have been extensively used in the aerospace field. Cadmium electroplating has been widely applied to promote protective coatings in aeronautical components, resulting in excellent corrosion protection combined with a good performance in cyclic loading. Ecological considerations allied to the increasing demands for corrosion resistance, resulted in the search for possible alternatives. Zinc-nickel alloys received considerable interest recently, since these coatings showed some advantages such as a good resistance to white and red rust, high plating rates and acceptation in the market. In this study the effects of zinc-nickel coatings electroplated on AISI 4340 high strength steel were analysed on rotating bending and axial fatigue strength, corrosion and adhesion resistance. Compressive residual stress field was measured by a X-ray tensometry prior to fatigue tests. Optical microscopy images showed coating thicknesses, adhesion and the existence of an uniform coverage of nearly all substrates. The fractured fatigue specimens were investigated using a scanning electron microscope. Three different zinc-nickel coating thicknesses were tested and comparison with rotating bending fatigue data from specimens cadmium electroplated and heat treated at 190°C for 3, 8 and 24 hours to avoid the diffusion of hydrogen in the substrate, was performed. Experimental results showed effect of coatings on the AISI 4340 steel behaviour when submitted to fatigue testing and the existence of coating thickness influence on the fatigue strength.

DEVELOPMENT OF NOVEL METHODS TO MINIMIZE THE IMPACT OF SEQUENCING ERRORS IN THE NEXT-GENERATION SEQUENCING DATA ANALYSIS

Next-generation sequencing (NGS) technology has become a prominent tool in biological and biomedical research. However, NGS data analysis, such as de novo assembly, mapping and variants detection is far from maturity, and the high sequencing error-rate is one of the major problems. . To minimize the impact of sequencing errors, we developed a highly robust and efficient method, MTM, to correct the errors in NGS reads. We demonstrated the effectiveness of MTM on both single-cell data with highly non-uniform coverage and normal data with uniformly high coverage, reflecting that MTM’s performance does not rely on the coverage of the sequencing reads. MTM was also compared with Hammer and Quake, the best methods for correcting non-uniform and uniform data respectively. For non-uniform data, MTM outperformed both Hammer and Quake. For uniform data, MTM showed better performance than Quake and comparable results to Hammer. By making better error correction with MTM, the quality of downstream analysis, such as mapping and SNP detection, was improved. SNP calling is a major application of NGS technologies. However, the existence of sequencing errors complicates this process, especially for the low coverage (

Estudio acústico y electroacústico de la sala 18 de Kinépolis (Madrid)

El objetivo de este proyecto se materializa en el diseño acústico y electroacústico de las salas de cine con número 18, 19, 20 y 21 del centro de cines Kinépolis situado en la Ciudad de la Imagen. Dichas salas son idénticas por lo que con el estudio y análisis de una se podrán extrapolar los resultados a las demás, por tanto a partir de ahora se realizará el diseño acústico y electroacústico centrado en la sala 18. Así pues se procederá a certificar que dicha sala cumple la norma THX. En dicho recinto se habrán aplicando con anterioridad diferentes técnicas de acondicionamiento sonoro (insonorización mediante el uso de materiales tanto absorbentes como reflectantes, arquitectura de la sala ), así como todos los acondicionamientos propios de un espacio de uso público cumpliendo las consiguientes normativas de seguridad. Se analizará la sala en su estado de partida mediante medidas acústicas in-situ tanto del tiempo de reverberación como del ruido de fondo, así como medidas espaciales con un medidor de alta precisión (láser); para posteriormente realizar las simulaciones en el programa EASE 4.01 de manera que la simulación sea lo más fidedigna posible. Estas medidas se realizarán de acuerdo a lo especificado en la norma UNE-EN ISO 3382. Cuando el comportamiento acústico del modelado de la sala sea el mismo que el de la sala real (respondan con el mismo Tiempo de Reverberación), mediante la introducción de los materiales adecuados y del ruido de fondo; se procederá al diseño electroacústico del equipo necesario para implementar el sistema de sonido multicanal Dolby (R). En el estudio electroacústico se distribuirán los diferentes altavoces que correctamente insertados ajustados sus niveles y retardos cubrirán con su señal uniformemente la sala cumpliendo los requisitos de la norma Dolby (R). Y finalmente una vez propuesto el sistema electroacústico y comprobado su correcto funcionamiento y por tanto el cumplimiento de la norma THX se propondrán mejoras en el sistema. Hay que señalar que aunque las recomendaciones THX son conocidas como norma THX no es una norma como tal, sino un conjunto de recomendaciones, que aconsejan utilizar una norma u otra para cada requisito. De ahora en adelante se referirá en este documento como norma THX. Se recuerda una vez más que dado que las salas son idénticas, y que las medidas realizadas en cada una de ellas son similares, se procederá en adelante al estudio de la sala única sala, la sala 18, siendo todos los estudios, análisis, comentarios y conclusiones aplicables a las otras 3 salas. Abstract The aim of this Project is the acoustic and electroacoustic design of the projection rooms 18th, 19th, 20th and 21st of the theater kinépolis, which is located at “Ciudad de la imagen”. These rooms are equal so with the studing and analazing of one of them , the results can be extrapolted from this one to the others, therefore as from now the and electroacoustic design will focus on the 18th room. As result the room will be certified that it comply with the standard THX. The starting point of the room will be analized such on-spot acoustical measures as the reverberation time and the noise level, in the same way the spatial measurements will be make with a precise laser meter, in order to perform simulations with the data obtained with the EASE 4.01 program. These mesurements should be made in accordance with the standard UNE-EN ISO 3382. Once the acoustical behavior of the simulated room became the same as the real room (the same reverberation times), through the configuration of the suitable materials and the background noise, previously measured, the electroacoustic design of the equipment necessary to develop the multichannel sound system Dolby (R) will be completed. In the electroacoustic design the sound power level and the dealys of the speakers and its amplifiers will be configurated till amplifiers provide an uniform coverage over the entire room in compliance with the Dolby (R) standard. Finally, once an electroacoustic system will be proposed and checked it works correctly in compliance with the THX standard, posible improvements will be identified. Abstract. Acoustic and electroacoustic study of the 18th room of the movie theater Kinépolis (Madrid) It must however be pointed out that although the THX standard is known as a standard it is actually a set of recommended practices made by Lucasfilm Ltd, anyway, from now on we will call it THX standard.

Development and characterisation of solution processed vanadium oxide and transparent metal oxide thin films

Metal oxide thin films are important for modern electronic devices ranging from thin film transistors to photovoltaics and functional optical coatings. Solution processed techniques allow for thin films to be rapidly deposited over a range of surfaces without the extensive processing of comparative vapour or physical deposition methods. The production of thin films of vanadium oxide prepared through dip-coating was developed enabling a greater understanding of the thin film formation. Mechanisms of depositing improved large area uniform coverage on a number of technologically relevant substrates were examined. The fundamental mechanism for polymer-assisted deposition in improving thin film surface smoothness and long range order has been delivered. Different methods were employed for adapting the alkoxide based dip-coating technique to produce a variety of amorphous and crystalline vanadium oxide based thin films. Using a wide range of material, spectroscopic and optical measurement techniques the morphology, structure and optoelectronic properties of the thin films were studied. The formation of pinholes on the surface of the thin films, due to dewetting and spinodal effects, was inhibited using the polymer assisted deposition technique. Uniform thin films with sub 50 nm thicknesses were deposited on a variety of substrates controlled through alterations to the solvent-alkoxide dilution ratios and employing polymer assisted deposition techniques. The effects of polymer assisted deposition altered the crystallized VO thin films from a granular surface structure to a polycrystalline structure composed of high density small in-plane grains. The formation of transparent VO based thin film through Si and Na substrate mediated diffusion highlighted new methods for material formation and doping.

Non-uniform printed antenna array for wireless communications in sports arenas

Wireless communications had a great development in the last years and nowadays they are present everywhere, public and private, being increasingly used for different applications. Their application in the business of sports events as a means to improve the experience of the fans at the games is becoming essential, such as sharing messages and multimedia material on social networks. In the stadiums, given the high density of people, the wireless networks require very large data capacity. Hence radio coverage employing many small sized sectors is unavoidable. In this paper, an antenna is designed to operate in the Wi-Fi 5GHz frequency band, with a directive radiation pattern suitable to this kind of applications. Furthermore, despite the large bandwidth and low losses, this antenna has been developed using low cost, off-the-shelf materials without sacrificing quality or performance, essential to mass production. © 2015 EurAAP.

Performance of asynchronous channel assignment scheme in non-uniform and dynamic topology WLANs

Dense deployments of wireless local area networks (WLANs) are fast becoming a permanent feature of all developed cities around the world. While this increases capacity and coverage, the problem of increased interference, which is exacerbated by the limited number of channels available, can severely degrade the performance of WLANs if an effective channel assignment scheme is not employed. In an earlier work, an asynchronous, distributed and dynamic channel assignment scheme has been proposed that (1) is simple to implement, (2) does not require any knowledge of the throughput function, and (3) allows asynchronous channel switching by each access point (AP). In this paper, we present extensive performance evaluation of this scheme when it is deployed in the more practical non-uniform and dynamic topology scenarios. Specifically, we investigate its effectiveness (1) when APs are deployed in a nonuniform fashion resulting in some APs suffering from higher levels of interference than others and (2) when APs are effectively switched `on/off' due to the availability/lack of traffic at different times, which creates a dynamically changing network topology. Simulation results based on actual WLAN topologies show that robust performance gains over other channel assignment schemes can still be achieved even in these realistic scenarios.

Comparing finite state machine test coverage criteria

To plan testing activities, testers face the challenge of determining a strategy, including a test coverage criterion that offers an acceptable compromise between the available resources and test goals. Known theoretical properties of coverage criteria do not always help and, thus, empirical data are needed. The results of an experimental evaluation of several coverage criteria for finite state machines (FSMs) are presented, namely, state and transition coverage; initialisation fault and transition fault coverage. The first two criteria focus on FSM structure, whereas the other two on potential faults in FSM implementations. The authors elaborate a comparison approach that includes random generation of FSM, construction of an adequate test suite and test minimisation for each criterion to ensure that tests are obtained in a uniform way. The last step uses an improved greedy algorithm.

Light Coverage on Colby College Campus

Outdoor lighting is an essential component for nighttime safety on college campuses. Outdoor lighting on Colby College campus is not uniform, leaving some areas with minimal light. The purpose of this project is to analytically evaluate if and where major walkways on Colby College have inadequate lighting. While we were unable to define inadequate lighting, we found that most paths on campus do appear to be well lit, while in general open spaces on campus have the lowest light levels.

Defining functional urban regions in Bahia, Brazil, using roadway coverage and population density variables

The concept of Functional Urban Regions (FURs), also called Metropolitan Regions (MRs), is not simple. It is clear, though, that they are not simply a combination of adjacent municipalities or areas. Different methods can be used for their definition. However, especially in developing countries, the application of some methods is not possible, due to the unavailability of detailed data. Alternative approaches have been developed based on spatial analysis methods and using variables extracted from available data. The objective of this study is to compare the results of two spatial analysis methods exploring two variables: population density and an indicator of transport infrastructure supply. The first method regards Exploratory Spatial Data Analyses tools, which define uniform regions based on specific variables. The second method used the same variables and the spatial analysis technique available in the computer program SKATER - Spatial 'K'luster Analysis by Tree Edge Removal. Assuming that those classifications of regions with similar characteristics can be used for identifying potential FURS, the results of all analyses were compared with one another and with the 'official' MR. A combined approach was also considered for comparison, but none of the results match the existing MR boundaries, what challenges the official definitions. (C) 2014 Elsevier Ltd. All rights reserved.

Low-density InAs QDs with subcritical coverage obtained by conversion of In nanocrystals

We report growth of InAs/GaAs quantum dots (QDs) by molecular beam epitaxy with low density of 2 μm−2 by conversion of In nanocrystals deposited at low temperatures. The total amount of InAs used is about one monolayer, which is less than the critical thickness for conventional Stranski–Krastanov QDs. We also demonstrate the importance of the starting surface reconstruction for obtaining uniform QDs. The QD emission wavelength is easily tunable upon post-growth annealing with no wetting layer signal visible for short anneals. Microphotoluminescence measurements reveal well separated and sharp emission lines of individual QDs.

Procedure for verification of sound source coverage over façades according to the International Standard ISO 140-5

This paper presents a new verification procedure for sound source coverage according to ISO 140?5 requirements. The ISO 140?5 standard applies to the measurement of façade insulation and requires a sound source able to achieve a sufficiently uniform sound field in free field conditions on the façade under study. The proposed method involves the electroacoustic characterisation of the sound source in laboratory free field conditions (anechoic room) and the subsequent prediction by computer simulation of the sound free field radiated on a rectangular surface equal in size to the façade being measured. The loudspeaker is characterised in an anechoic room under laboratory controlled conditions, carefully measuring directivity, and then a computer model is designed to calculate the acoustic free field coverage for different loudspeaker positions and façade sizes. For each sound source position, the method provides the maximum direct acoustic level differences on a façade specimen and therefore determines whether the loudspeaker verifies the maximum allowed level difference of 5 dB (or 10 dB for façade dimensions greater than 5 m) required by the ISO standard. Additionally, the maximum horizontal dimension of the façade meeting the standard is calculated and provided for each sound source position, both with the 5 dB and 10 dB criteria. In the last section of the paper, the proposed procedure is compared with another method used by the authors in the past to achieve the same purpose: in situ outdoor measurements attempting to recreate free field conditions. From this comparison, it is concluded that the proposed method is able to reproduce the actual measurements with high accuracy, for example, the ground reflection effect, at least at low frequencies, which is difficult to avoid in the outdoor measurement method, and it is fully eliminated with the proposed method to achieve the free field requisite.