Bleached kraft pulp production from Pinus tecunumanii (Eguiluz e Perry)

The use of 12-year-old Pinus tecunumanii (Eguiluz e Perry) grown in Colombia was evaluated for bleached kraft pulp production. Kraft pulps of kappa number 30 ± 1 were produced, and oxygen delignified and bleached to 90% ISO with ECF processes. The bleached pulps produced under optimum conditions were evaluated with regard to their strength properties. Pinus tecunumanii wood required low effective alkali charge to reach the desired kappa number and the unbleached pulp showed high oxygen delignification efficiency and bleachability when a OD(EO)DED sequence was used. The bleached pulps presented good physical-mechanical properties, which are comparable to those obtained with more traditional pines such as Pinus taeda and Pinus radiata. The results demonstrate that this tropical pine species is a suitable raw material for bleached kraft pulp production

Surface properties of eucalyptus pulp fibres as reinforcement of cement-based composites

The objective of the present work is to evaluate the effects of the surface properties of unrefined eucalyptus pulp fibres concerning their performance in cement-based composites. The influence of the fibre surface on the microstructure of fibre-cement composites was evaluated after accelerated ageing cycles, which simulate natural weathering. The surface of unbleached pulp is a thin layer that is rich in cellulose, lignin, hemicelluloses, and extractives. Such a layer acts as a physical and chemical barrier to the penetration of low molecular components of cement. The unbleached fibres are less hydrophilic than the bleached ones. Bleaching removes the amorphous lignin and extractives from the surface and renders it more permeable to liquids. Atomic force microscopy (AFM) helps in understanding the fibre-cement interface. Bleaching improved the fibre- cement interfacial bonding, whereas fibres in the unbleached pulp were less susceptible to the re-precipitation of cement hydration products into the fibre cavities (lumens). Therefore, unbleached fibres can improve the long-term performance of the fibre-cement composite owing to their delayed mineralization.

Hiokkeen laatuvaihteluja aiheuttavat tekijät ja vaihteluiden vaimentamismahdollisuudet

Myllykoski Paper Oy:n hiokkeen laadussa ja prosessivesien ominaisuuksissa tapahtuu vaihtelua ajan suhteen. Tämä käy ilmi useiden vuosien aikana kerätyistä laatuseurantatiedoista. Diplomityön tavoitteena oli selvittää hiokkeen ja kierto-vesien laatuun vaikuttavat tekijät ja kehittää laadunvaihtelua hillitseviä toimenpi-teitä. Työn kirjallisuusosassa pyrittiin löytämään tekijöitä, jotka voivat aiheuttaa valmiin hiokkeen laatuun vaihtelua. Lähtökohtaisesti laatuvaihteluita aiheuttavat tekijät jaettiin raaka-aine- tai prosessivaihteluksi. Työn kokeellisessa osassa selvitettiin eri hioke- ja prosessivesiominaisuuksien kehittymistä tarkastelemalla eri mittaussuureista kerättyjä aineistoja erilaisin aika-välein. Aluksi tarkasteltiin hiokkeen ja vesien ominaisuuksia viiden vuoden ajan-jaksolla, josta siirryttiin tarkastelemaan lyhyempiä aikavälejä. Käytetty mittausaineisto oli peräisin DW-tietovarastosta ja PHD-reaaliaikatietokannasta. Työn tuloksista kävi muun muassa ilmi, että painehiokkeen lujuusominaisuudet ovat hienoisesti alentuneet viimeisen viiden vuoden aikana. Muutos selittyy hiokkeen pitkäkuituosuuden ja kuitupuun keskimääräisen läpimitan alenemisella. Lisäksi valkaisemattomien hiokkeiden vaaleudet ovat alentuneet samallakun prosessivedet ovat muuttuneet likaisemmiksi. Kehitykseen on vaikuttanut vesikiertojen kasvanut sulkemisaste ja uusi peroksidivalkaisulaitos. Jatkotoimenpide-ehdotukset painottuvat pääosin vesiajotilanteiden hallintaan. Vesiajoaiheuttaa aina suuria muutoksia niin hiokkeen kuin myös kiertovesien laatuun.

Otsonin käyttö paperin ja kartongin valmistuksen kiertovesien mikrobiologisen tilan hallintaan

Diplomityössä tutkittiin otsonin käytön soveltuvuutta ja etsittiin optimaalista soveltamistapaa kartonki- ja paperikoneen kiertoveden mikrobiologisen tilan hallintaan. Kirjallisuusosassa selvitettiin otsonin tuotannon nykytekniikkaa sekä otettiin selvää saatavilla olevista kapasiteetiltaan riittävistä otsonigeneraattoreista. Kirjallisuuden perusteella selvitettiin myös otsonin reaktioita paperi- ja kartonkikoneen kiertovesissä olevien orgaanisten ja epäorgaanisten aineiden kanssa. Lisäksi käsiteltiin otsonin käytön eri sovelluksia vedenpuhdistuksessa sekä perehdyttiin aikaisemmin tehtyihin tutkimuksiin otsonin käytöstä mikrobitorjuntaan paperi- ja kartonkikoneiden kiertovesistä. Kokeellisessa osassa määritettiin sopiva otsoniannos valkaisematonta sellua käyttävän koneen kiekkosuotimen kirkkaalle ja samealle suodokselle. Vesien otsonointi suoritettiin otsonipilotlaitteistolla. Työssä tutkittiin otsonoinnin vaikutusta kiertoveden mikrobiologisiin ja kemiallisiin ominaisuuksiin. Lisäksi tarkasteltiin kiertoveden otsonoinnin vaikutuksia koepaperikoneella valkaisemattomasta sel-lusta ja hylkymassasta valmistettujen lopputuotteiden laatuun. Työssä arvioitiin myös otsonin käytön mahdollisuutta osittain korvaamaan jo käytössä olevia hapettavia biosidejä. Samealle suodokselle sopivaksi otsoniannokseksi osoittautui 120 mg O3/l (0,3 mg O3/mg CODCr) ja kirkkaalle suodokselle riittävä annos olisi 60 mg O3/l (0,2 mg/mg CODCr). Näillä annoksilla kiertoveden mikrobireduktiot olivat 98–100 %. Kiertoveden hapetuskyky kasvoi 9-14 % ja pH laski yhdellä yksiköllä otsonoinnin vaikutuksesta. Kiertoveden kemiallisiin ominaisuuksiin otsonoinnilla oli edullinen vaikutus, sillä veden sameus, kiintoaine- ja CODCr-pitoisuudet laskivat. Koepaperikoneella havaittiin perälaatikon ilmapitoisuuden vähentyneen jopa 49 % käytettäessä ot-sonoitua kiertovettä. Mikrobiologiset analyysit suoritettiin koepaperikoneen massalle, viiravedelle ja lopputuotteelle. Tutkimusten perusteella mikrobientorjunnan kannalta parhaimmaksi otsonin annos-telupaikaksi osoittautui samea suodos. Massan, viiraveden ja lopputuotteen mikrobimäärät alenivat selvästi. Kemialliset analyysit osoittivat, että kirkasta suodosta käytettäessä oli koepaperikoneen vii-raveden kemiallinen tila parantunut LK-aineen muuttuessa hydrofiilisemmäksi ja sen sitoutumisky-vyn parantuessa. Samealla suodoksella ei muutosta havaittu. Valkaisemattomasta sellusta ja päällystetystä hylystä koepaperikoneella valmistettujen lopputuotteiden lujuus- ja aistinvaraisissa ominaisuuksissa ei tapahtunut merkittävää muutosta. Tulosten perusteella otsonia voisi käyttää korvaamaan hinnaltaan kalliimpia hapettavia biosidejä. Otsonin etuna on, ettei sille resistenttejä mikrobikantoja ole. Kirjallisuuden perusteella otsonin heikkoutena on sen tehon paikallisuus eli otsonin lisänä on käytettävä jotain muuta sekundääristä biosidia ylläpitämään matala mikrobitaso otsonoinnin jälkeen.

Kaasun dispergoituminen tehdasmittakaavaisessa keskisakean massan sekoittimessa

Työn tarkoituksena oli selvittää Proto 10 kemikaalisekoittimen kyky dispergoida kaasua keskisakean valkaistun mäntysellun joukkoon. Työssä käytettiin kuvantamistekniikkaa, jonka avulla pystyttiin näkemään sekoittimen ja putkiston sisälle sekoitustapahtuman aikana. Muodostunutta dispersiota tarkasteltiin kolmesta kuvauspisteestä, joista yksi sijaitsi sekoittimen pesässä ja kaksi putkistossa sekoittimen jälkeen. Työssä verrattiin myös laboratoriosekoittimella saatuja tuloksia teollisen mittakaavan sekoittimella saatuihin tuloksiin, sekä määritettiin tarvittava pinta-aktiivisen aineen konsentraatio, jolla saavutettiin ruskeaa massaa vastaava vaahtoaminen. Työn kokeellinen osuus koostui kolmesta osasta. Ensimmäisessä vaiheessa tutkittiin ruskeasta mänty- ja koivumassasta lingotun suodoksen vaahtoamista ja verrattiin sitä vedellä ja pesuaineella saatavaan vaahtoon. Toisessa vaiheessa suoritettiin referenssiajot laboratoriosekoittimen ja teollisen mittakaavan sekoittimen vertailua varten Quantum Mark IV laboratoriosekoittimella. Kolmannessa vaiheessa tutkittiin Proto 10 sekoittimen kykyä dispergoida kaasua mäntysellun joukkoon eri pyörimisnopeuksilla ja virtaamilla. Työn tuloksien perusteella energiankäytön kannalta paras pyörimisnopeus Proto 10 sekoittimelle on 1500 min-1. Nostamalla kierrosnopeutta yli tämän ei saavutettu merkittävää parannusta dispersion laadussa varsinkaan suuremmilla virtaamilla. Virtaamalla todettiin olevan suuri merkitys sekoitustulokseen. Laboratoriosekoittimella tehtyjen kokeiden todettiin vastaavan parhaiten teollisen mittakaavan tuloksia pyörimisnopeudella 1200 min-1.

Sellumassan varastosäiliön rakenneanalyysi

Tämä työ käsittelee valkaistun ja valkaisemattoman sellumassan varastosäiliön tärinää ja värähtelyä. Värähtelyn seurauksena säiliön seinämän jäykisterenkaan hitsausliitokseen on syntynyt särö. Työn tavoitteena on selvittää, mikä johtaa särön syntyyn ja miten kestäväm-piä varastosäiliöitä voidaan rakentaa materiaali-, valmistus- tai rakennemuutoksien avulla. Työ alkoi tutkimalla rakennemateriaalina olevan duplex-teräksen mikrorakenteen ominai-suuksia, sekä sen hitsattavuutta ja seostamista kirjallisuustutkimuksena. Kirjallisuustutki-musta jatkettiin selvittämällä mahdollisia vaurion syntymekanismeja seinämän särölle. Työssä analysoitiin myös tehtaalla mitattuja värähtelyarvoja. Lopuksi laskettiin FE-analyysillä tyhjän varastosäiliön ominaismuodot ja -taajuudet moodianalyysillä, sekä selvi-tettiin harmonisella analyysillä pinnankorkeuden vaihtelun vaikutus siirtymävasteeseen ja kriittisiin värähtelytaajuuksiin. Varastosäiliöön kohdistuvaa värähtelyä ei ole mahdollista poistaa kokonaan, mutta väräh-telyn aiheuttamia seurauksia kyetään rajaamaan useilla keinoilla. Toimenpiteinä voivat olla ainakin seinämän materiaalin paksuuden lisääminen, jäykisteripojen lisääminen ja kriittisten sellun pinnankorkeuksien välttäminen. Kriittiseksi pinnankorkeudeksi havaittiin 40–45 %:n täyttöaste ja turvalliseksi korkeudeksi 35–38 %:n täyttöaste. Varastosäiliölle kriittisen ominaistaajuuden katsotaan syntyvän taajuuksilla 3,3–3,8 Hz ja 5,8–6,4 Hz. Sellumassa putoaa varastosäiliöön noin 2 Hz taajuudella.

Modelo de otimização para seleção de árvores matrizes de Eucalyptus grandis

Individual data of basic density and volume of wood, pulp kappa number, soluble lignin, cost of pulping process as well as gravimetric gross yield of pulping process were used from 64 trees of Eucalyptus grandis W. Hill ex Maiden from a commercial population at Lençóis Paulista, SP. The Eucalyptus grandis's seeds were originally from a Seed Production Area (SPA) of Duratex S/A at Botucatu, SP. Obtained data were quantified considering objective of maximization no-bleaching pulp and volume and mass wood restriction, mass of residual and soluble lignin, planted area and pulping process cost. it has also been aimed a selection method for matrix trees through mathematical programming techniques. Obtained strategy maximized the economical result, selected matrix trees and followed all limits of technological and organizing productivities imposed by the company. It also aimed the production of no-bleaching pulp within the planned time.

Dimensões de cavacos industriais de eucalipto e relações com polpação, resistência e morfologia de fibras na polpa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The Number of Bleaching Sessions Influences Pulp Tissue Damage in Rat Teeth

Introduction: Hydrogen peroxide tooth bleaching is claimed to cause alterations in dental tissue structures. This study investigated the influence of the number of bleaching sessions on pulp tissue in rats. Methods: Male Wistar rats were studied in 5 groups (groups 1S-5S) of 10 each, which differed by the number (1-5) of bleaching sessions. In each session, the animals were anesthetized, and 35% hydrogen peroxide gel was applied to 3 upper right molars. Two days after the experimental period, the animals were killed, and their jaws were processed for light microscope evaluation. Pulp tissue reactions were scored as follows: 1, no or few inflammatory cells and no reaction; 2, <25 cells and a mild reaction; 3, between 25 and 125 cells and a moderate reaction; and 4, 125 or more cells and a severe reaction. Results from each experimental group were compared between groups and within groups to the corresponding unbleached upper left molars and analyzed for significant differences using the Kruskal-Wallis test (P < .05). Results: All tissue sections showed significant bleaching-induced changes in the dental pulp. After 1 bleaching session, necrotic tissue in the pulp horns and underlying inflammatory changes were observed. The extent and intensity of these changes increased with the number of bleaching sessions. After 5 sessions, the changes included necrotic areas in the pulp tissue involving the second third of the radicular pulp and intense inflammation in the apical third. Conclusions: The number of bleaching sessions directly influenced the extent of pulp damage. © 2013 American Association of Endodontists.

Microbial Evaluation Of Traumatized Teeth Treated With Triple Antibiotic Paste Or Calcium Hydroxide With 2% Chlorhexidine Gel In Pulp Revascularization.

Revascularization outcome depends on microbial elimination because apical repair will not happen in the presence of infected tissues. This study evaluated the microbial composition of traumatized immature teeth and assessed their reduction during different stages of the revascularization procedures performed with 2 intracanal medicaments. Fifteen patients (7-17 years old) with immature teeth were submitted to the revascularization procedures; they were divided into 2 groups according to the intracanal medicament used: TAP group (n = 7), medicated with a triple antibiotic paste, and CHP group (n = 8), dressed with calcium hydroxide + 2% chlorhexidine gel. Samples were taken before any treatment (S1), after irrigation with 6% NaOCl (S2), after irrigation with 2% chlorhexidine (S3), after intracanal dressing (S4), and after 17% EDTA irrigation (S5). Cultivable bacteria recovered from the 5 stages were counted and identified by means of polymerase chain reaction assay (16S rRNA). Both groups had colony-forming unit counts significantly reduced after S2 (P < .05); however, no significant difference was found between the irrigants (S2 and S3, P = .99). No difference in bacteria counts was found between the intracanal medicaments used (P = .95). The most prevalent bacteria detected were Actinomyces naeslundii (66.67%), followed by Porphyromonas endodontalis, Parvimonas micra, and Fusobacterium nucleatum, which were detected in 33.34% of the root canals. An average of 2.13 species per canal was found, and no statistical correlation was observed between bacterial species and clinical/radiographic features. The microbial profile of infected immature teeth is similar to that of primarily infected permanent teeth. The greatest bacterial reduction was promoted by the irrigation solutions. The revascularization protocols that used the tested intracanal medicaments were efficient in reducing viable bacteria in necrotic immature teeth.

Polyphenol Extraction Optimisation From Ceylon Gooseberry (dovyalis Hebecarpa) Pulp.

Originally from Asia, Dovyalis hebecarpa is a dark purple/red exotic berry now also produced in Brazil. However, no reports were found in the literature about phenolic extraction or characterisation of this berry. In this study we evaluate the extraction optimisation of anthocyanins and total phenolics in D. hebecarpa berries aiming at the development of a simple and mild analytical technique. Multivariate analysis was used to optimise the extraction variables (ethanol:water:acetone solvent proportions, times, and acid concentrations) at different levels. Acetone/water (20/80 v/v) gave the highest anthocyanin extraction yield, but pure water and different proportions of acetone/water or acetone/ethanol/water (with >50% of water) were also effective. Neither acid concentration nor time had a significant effect on extraction efficiency allowing to fix the recommended parameters at the lowest values tested (0.35% formic acid v/v, and 17.6 min). Under optimised conditions, extraction efficiencies were increased by 31.5% and 11% for anthocyanin and total phenolics, respectively as compared to traditional methods that use more solvent and time. Thus, the optimised methodology increased yields being less hazardous and time consuming than traditional methods. Finally, freeze-dried D. hebecarpa showed high content of target phytochemicals (319 mg/100g and 1,421 mg/100g of total anthocyanin and total phenolic content, respectively).

Micromorphology Of The Dental Pulp Is Highly Preserved In Cancer Patients Who Underwent Head And Neck Radiotherapy.

Teeth are often included in the radiation field during head and neck radiotherapy, and recent clinical evidence suggests that dental pulp is negatively affected by the direct effects of radiation, leading to impaired sensitivity of the dental pulp. Therefore, this study aimed to investigate the direct effects of radiation on the microvasculature, innervation, and extracellular matrix of the dental pulp of patients who have undergone head and neck radiotherapy. Twenty-three samples of dental pulp from patients who finished head and neck radiotherapy were analyzed. Samples were histologically processed and stained with hematoxylin-eosin for morphologic evaluation of the microvasculature, innervation, and extracellular matrix. Subsequently, immunohistochemical analysis of proteins related to vascularization (CD34 and smooth muscle actin), innervation (S-100, NCAM/CD56, and neurofilament), and extracellular matrix (vimentin) of the dental pulp was performed. The morphologic study identified preservation of the microvasculature, nerve bundles, and components of the extracellular matrix in all studied samples. The immunohistochemical analysis confirmed the morphologic findings and showed a normal pattern of expression for the studied proteins in all samples. Direct effects of radiotherapy are not able to generate morphologic changes in the microvasculature, innervation, and extracellular matrix components of the dental pulp in head and neck cancer patients.

Pulp tissue from primary teeth: new source of stem cells

SHED (stem cells from human exfoliated deciduous teeth) represent a population of postnatal stem cells capable of extensive proliferation and multipotential differentiation. Primary teeth may be an ideal source of postnatal stem cells to regenerate tooth structures and bone, and possibly to treat neural tissue injury or degenerative diseases. SHED are highly proliferative cells derived from an accessible tissue source, and therefore hold potential for providing enough cells for clinical applications. In this review, we describe the current knowledge about dental pulp stem cells and discuss tissue engineering approaches that use SHED to replace irreversibly inflamed or necrotic pulps with a healthy and functionally competent tissue that is capable of forming new dentin.

In vitro study of the pulp chamber temperature rise during light-activated bleaching

This study evaluated in vitro the pulp chamber temperature rise induced by the light-activated dental bleaching technique using different light sources. The root portions of 78 extracted sound human mandibular incisors were sectioned approximately 2 mm below the cementoenamel junction. The root cavities of the crowns were enlarged to facilitate the correct placing of the sensor into the pulp chamber. Half of specimens (n=39) was assigned to receive a 35% hydrogen peroxide gel on the buccal surface and the other halt (n=39) not to receive the bleaching agent. Three groups (n=13) were formed for each condition (bleach or no bleach) according to the use of 3 light sources recommended for dental bleaching: a light-emitting diode (LED)laser system, a LED unit and a conventional halogen light. The light sources were positioned perpendicular to the buccal surface at a distance of 5 mm and activated during 30 s. The differences between the initial and the highest temperature readings for each specimen were obtained, and, from the temperature changes, the means for each specimen and each group were calculated. The values of temperature rise were compared using Kruskal-Wallis test at 1% significance level. Temperature rise varied significantly depending on the light-curing unit, with statistically significant differences (p<0.01) among the groups. When the bleaching agent was not applied, the halogen light induced the highest temperature rise (2.38±0.66ºC). The LED unit produced the lowest temperature increase (0.29±0.13ºC); but there was no significant difference between LED unit and LED-laser system (0.35±0.15ºC) (p>0.01). When the bleaching agent was applied, there were significant differences among groups (p<0.01): halogen light induced the highest temperature rise (1.41±0.64ºC), and LED-laser system the lowest (0.33±0.12ºC); however, there was no difference between LED-laser system and LED unit (0.44±0.11ºC). LED and LED-laser system did not differ significantly from each other regardless the temperature rise occurred with or without bleaching agent application. It may be concluded that during light-activated tooth bleaching, with or without the bleaching agent, halogen light promoted higher pulp chamber temperature rise than LED unit and LED-laser system. The tested light-curing units provided increases in the pulp chamber temperature that were compatible with pulpal health.

Pulp capping materials exert an effect on the secretion of IL-1β and IL-8 by migrating human neutrophils

Pulp repair is a complex process whose mechanisms are not yet fully understood. The first immune cells to reach the damaged pulp are neutrophils that play an important role in releasing cytokines and in phagocytosis. The objective of this study was to analyze the effect of different pulp-capping materials on the secretion of interleukin-1 beta (IL-1β) and interleukin-8 (IL-8) by migrating human neutrophils. Neutrophils were obtained from the blood of three healthy donors. The experimental groups were calcium hydroxide [Ca(OH)2], an adhesive system (Single Bond), and mineral trioxide aggregate (MTA). Untreated cells were used as control. Transwell chambers were used in performing the assays to mimic an in vivo situation of neutrophil chemotaxis. The pulp-capping materials were placed in the lower chamber and the human neutrophils, in the upper chamber. The cells were counted and the culture medium was assayed using ELISA kits for detecting and quantifying IL-1β and IL8. The data were compared by ANOVA followed by Tukey's test (p < 0.05). The secretion of IL-8 was significantly higher in all groups in comparison to the control group (p < 0.05). The adhesive system group showed higher IL-8 than the MTA group (p < 0.05). The secretion of IL-1β was significantly greater only in the MTA group (p < 0.001). It was concluded that only MTA is able to improve the secretion of IL-1β, and all materials tested increased IL-8 secretion. These results combined with all the other biological advantages of MTA indicate that it could be considered the material of choice for dental pulp capping.