Desenvolvimento de tubo ARBL contendo 1Cr 0,2Mo fabricado pelo processo ERW/HF destinado à indústria de petróleo e gás

Pós-graduação em Engenharia Mecânica - FEG

Avaliação da influência dos parâmetros de processo de soldagem MIG no surgimento de poros em tubos de alumínio

The process of electric arc welding with shielding gas (GMAW) is being increasingly used in various industrial applications. This process occurs by which an electric arc is established between the work piece and a consumable in the form of wire, the arc melts the wire continuously as it is fed to the weld pool. The weld metal is protected from the atmosphere by flowing a gas (or gas mixture) inert or active. This paper presents a study of the welding process GMAW - MIG on aluminum tubes, alloy 6101 - T6, used in the manufacture of armored busbar, intended for driving electric power plants. 5(five) were welded specimens, changing certain welding parameters at each time was monitored welding joint as well as the interpass temperature. Tests were performed bending, tensile and macrographical analysis of body-of-evidence and through its results was possible to reach a better welding condition, which minimizes the appearance of pores, since the porosity has great influence on the mechanical strength and electrical conductivity of welded pipes

Modelagem do resfriamento para a zona termicamente afetada pela soldagem de tubos de aço carbono

Because the high consumption of welded pipe for exploration and conduction oil and gas, optimization of manufacturing processes is necessary to obtain better productivity, efficiency and cost reduction. The objective of this study is to analyze the forms of heat transfer during the welding of pipes using longitudinal submerged arc process them to propose a model for the temperature distribution in the welded region. For this analysis are addressed as the heat transfer modes operate in the specified welding process and the necessary considerations for the mathematical model were obtained. The calculations were performed and the simulations needed to obtain the temperature distribution in the tube were carried out. Therefore, the practice was satisfactory and the results showed a range of temperatures along the pipe for a particular model and the future suggestions for improvement of this work

Análise da resistência à fadiga de tubos de aço API 5CT N80 Tipo Q soldados via processo de indução magnética de alta frequência (HFIW)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da fissuração por fadiga em tubos durante transporte marítimo

Tubos de aço são transportados diariamente em todo o mundo, por caminhão, trem ou navio. Conseqüentemente, danos de transporte, podem ocorrer com freqüência e regularidade. O tipo de dano particular selecionado para este estudo foi o de trinca por fadiga, o qual é considerado como um dos mais críticos. Neste trabalho foram estudados tubos de aço fabricados de acordo com os requisitos da norma API 5L [1]. Foram efetuadas caracterizações químicas, mecânicas e metalográficas de um tubo com diâmetro 609,6 mm e espessura 15,87 mm grau X-65. A simulação do transporte por navio de tubos de aço foi feita submetendo-se seções de tubo com comprimento igual a 0,1 metro, a ciclos de fadiga por meio de máquina servo-hidráulica. Foi possível concluir que em tubos soldados, a região adjacente ao cordão de solda é a mais crítica, e que quando o posicionamento do tubo na carga é efetuado de maneira que a solda fique apoiada sobre alguma superfície rígida, a ocorrência de trinca por fadiga torna-se possível principalmente se os procedimentos de manuseio, carregamento e transporte não forem executados da maneira como recomendada pelos fabricantes de tubos e pela norma API [2].

Influência do aporte de calor e da velocidade de soldagem na tenacidade da solda HF-ERW

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da ocorrência de trinca por fadiga em tubos de aços soldados, devido ao transporte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aumento da velocidade de soldagem para processo de arco submerso em juntas de um tubo de aço API X70

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Determinação experimental da tenacidade à fratura em baixas temperaturas de tubos de aço API 5L X70

Because of the great metallurgical advances, the welded tubes by HF / ERW (High Frequency / Electrical Resistance Welding) have played a more active role in the oil and gas, gradually replacing tubes produced by other processes (UOE, SAW, and others) to deep water applications, in high and extremely low temperatures, highpressure conditions and in highly corrosive environments. However, studies have revealed that defects in the welded joints are in one of main causes of failures in pipelines. Associated with damage external and the stringent requirements of this sector, the welded joints become particularly critical for his toughness and the determination of this particular property is fundamental. This study aims to evaluate the toughness of the HF / ERW pipes in HSLA steel API X70 class, used in pipelines transport systems of gas and oil from data obtained with CTOD tests (Crack Tip Opening Displacement). The main objectives of this project are: mechanical and microstructural characterization of steels API X70 manufactured in Brazil; and evaluation of the toughness of weld process by HF / ERW steel API X70 national. After having the tests done, mechanical, chemical and metallurgical, we have the conclusion that those pipe are in agreement to API 5L 42ª edition for X70MO and the toughness behaves like the expected

Investigação experimental da tenacidade em tubos de aço API 5L X70 soldados pelo processo HF/ERW

Studies about structural integrity are very important when it desires to prevent disasters associated with flaws inherent in materials used in structural components. The welded joints in steel pipes used to conduction and distribution of oil and gas correspond to the regions most susceptible to flaw. Aiming to contribute to this research line, the present study was designed to assess experimentally the structural integrity of welded joints in steel pipes API 5L X70 used in pipeline systems. This assessment is given from tests of CTOD, whose aim is simulate in laboratory the real behaviour of crack from of his propagation on the welded joint obtained by high frequency electric resistance welding. In this case, the analyses are performed from specimens SE(B) obtained directly of steel pipe API 5L X70. The proposed methodology involves tests of CTOD at lower temperature, in order to assess the toughness of material in critical operation conditions. From performance of CTOD tests, was possible assess the toughness of welded joints in terms of quantity through CTOD parameter and in terms of quality from behaviour of curve load versus CMOD. In this study, also, sought to compare CTOD’s results obtained through rules ASTM E1820 (2008) and BS 7448 (1991). Although the two standards cited previously have adopted different parameters to calculated the value of CTOD, concluded that the values of CTOD tend to converge for a common value

Análise microestrutural de tubos API P110, para prospecção de petróleo e gás, soldados pelo processo HF/ERW

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT P110, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of nonmetallic inclusions in the welded joint

Identificação de causas especiais no processo que aumentam a ocorrência de poro na solda de tubos de aço: aplicação etapas definir, medir e analisar do DMAIC

This work covers the methodology Six Sigma with the application of the steps Define, Measure and Analyze a company of steel tubes, with the objective of identify special causes in the process that drives the creation of the pore defect in the solder. It is highlighted the fact that this work is the base of an continuous upgrade project that aims in eliminating the occurrence of this defect. The motivation is given to the necessity of improving the productivity of the factory, considering that the defect occurs at random and your causes are unknown. This way, it was defined that the problem to analyze, measured the capability of the process in DPMO and analyzed with the aid of graph by attribute P. The results show the process that present special cases, as well as the process considered ideal, This way it was stated that in this work, the processes destabilized and the controlled, allowing a comparison of the characteristics for the elaboration of concise action plans to eliminate the defect. The project must follow the steps Upgrade and control the methodology Six Sigma, in order to ensure success in his execution, aiming to amplify the competitive edge of the business

Avaliação de juntas soldadas em tubos de aço carbono submetidos a altas temperatura e pressões

The welding process in industrial piping is still the most effective way to ensure the durability and quality of the wide range of industrial process, although because of the high demand for energy and quality of the produced products, the piping has been constantly tested for high pressure applications and still high temperature. The welding method analyzed is the TIG (Tungsten Inert Gas) welding or GTAW (Gas-Shielded Tungsten Arc Welding), which ones have as principal feature the utilization of a not consumable tungsten electrode in the torch extremity , in this process is necessary a protective atmosphere of inert gas. The welding TIG advantage is the obtaining of a welded seam clean and with quality for not has slag after the welding. This work has as objective show the variability in the carbon steel piping welding parameters and by the tests in four proof bodies will be shown the influence of the variation of the welding methods in a welded seam. The tests will vary since the piece to be welded preparation, till penetrating liquid tests, welding macrography, welding x-ray and traction tests. Even been a clean and with quality welding is necessary a final inspection in the seam welded looking for defects almost inevitable resulted of the welded process, the obtained results have the objective of indicate and minimize the defects to ensure quality and durability of the welded seam

Análise da resistência à fadiga de tubos de aço API 5CT N80 Tipo Q soldados via processo de indução magnética de alta frequência (HFIW)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.