Examination of the LBM in simulation of microchannel flow in transitional regime

The gas flows in micro-electro-mechanical systems possess relatively large Knudsen number and usually belong to the slip flow and transitional flow regimes. Recently the lattice Boltzmann method (LBM) was proposed by Nie et al. in Journal of Statistical Physics, vol. 107, pp. 279-289, in 2002 to simulate the microchannel and microcavity flows in the transitional flow regime. The present article intends to test the feasibility of doing so. The results of using the lattice Boltzmann method and the direct simulation Monte Carlo method show good agreement between them for small Kn (Kn = 0.0194), poor agreement for Kn = 0.194, and large deviation for Kn = 0.388 in simulating microchannel flows. This suggests that the present version of the lattice Boltzmann method is not feasible to simulate the transitional channel flow.

A Universal Flow Regime Map for Horizontal Two-Phase Flow in Pipes

A new universal flow map has been developed for two-phase co-current flow. The map has been successfully tested against wide variety of data. Flow regime transition predictors suggested by other authors have been shown to be useful. New transitional models are proposed for the stratified to annular regimes, blow through slug and intermittent regimes.

Flow regime prediction via froude number calculation in a rock-bedded stream

Mathematical predictions of flow conditions along a steep gradient rock bedded stream are examined. Stream gage discharge data and Manning's Equation are used to calculate alternative velocities, and subsequently Froude Numbers, assuming varying values of velocity coefficient, full depth or depth adjusted for vertical flow separation. Comparison of the results with photos show that Froude Numbers calculated from velocities derived from Manning's Equation, assuming a velocity coefficient of 1.30 and full depth, most accurately predict flow conditions, when supercritical flow is defined as Froude Number values above 0.84. Calculated Froude Number values between 0.8 and 1.1 correlate well with observed transitional flow, defined as the first appearance of small diagonal waves. Transitions from subcritical through transitional to clearly supercritical flow are predictable. Froude Number contour maps reveal a sinuous rise and fall of values reminiscent of pool riffle energy distribution.

Analysis of heat transfer coefficient in silica nanofluids with water as base fluid under transitional flow

The effect of Reynolds number variation in a vertical double pipe counterflow heat exchanger due to the changes in viscosity can cause the change in flow regime, for instance, when heats up and cools down, it can convert from turbulent to laminar or inversely, that can have significant effect on heat transfer coefficient and pressure drop. Mainly, the range of transition phase has been studied in this study with the investigation of silica nanofluid dispersed in water in three different concentrations. The results have been compared with distilled water sample and showed a remarkable raise in heat transfer coefficient while pressure drop has been increased respectively, as well. Although pumping power has to go up at the same time and it is a drawback, heat transfer efficiency grows for diluted samples. On the other hand, for the most concentrated sample, effect of pressure drop dominates which leads to decline in the overall efficiency.

Flow regime transition criteria for two-phase flow at reduced gravity conditions

Flow regime transition criteria are of practical importance for two-phase flow analyses at reduced gravity conditions. Here, flow regime transition criteria which take the friction pressure loss effect into account were studied in detail. Criteria at reduced gravity conditions were developed by extending an existing model with various experimental datasets taken at microgravity conditions showed satisfactory agreement. Sample computations of the model were performed at various gravity conditions, such as 0.196, 1.62, 3.71, and 9.81 m/s2 corresponding to micro-gravity and lunar, Martian and Earth surface gravity, respectively. It was found that the effect of gravity on bubbly-slug and slug-annular (churn) transitions in a two-phase flow system was more pronounced at low liquid flow conditions, whereas the gravity effect could be ignored at high mixture volumetric flux conditions. While for the annular flow transitions due to flow reversal and onset of dropset entrainment, higher superficial gas velocity was obtained at higher gravity level.

Deformation and crystallization of Zr-based amorphous alloys in homogeneous flow regime

The purpose of this study is to experimentally investigate the interaction of inelastic deformation and microstructural changes of two Zr-based bulk metallic glasses (BMGs): Zr41.25Ti13.75Cu12.5Ni10Be22.5 (commercially designated as Vitreloy 1 or Vit1) and Zr46.75Ti8.25Cu7.5Ni10Be27.5 (Vitreloy 4, Vit4). High-temperature uniaxial compression tests were performed on the two Zr alloys at various strain rates, followed by structural characterization using differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). Two distinct modes of mechanically induced atomic disordering in the two alloys were observed, with Vit1 featuring clear phase separation and crystallization after deformation as observed with TEM, while Vit4 showing only structural relaxation with no crystallization. The influence of the structural changes on the mechanical behaviors of the two materials was further investigated by jump-in-strain-rate tests, and flow softening was observed in Vit4. A free volume theory was applied to explain the deformation behaviors, and the activation volumes were calculated for both alloys.

Configuration optimization of hypersonic vehicles under transitional flow conditions

The rarefied gas effects on several configurations are investigated under hypersonic flow conditions using the direct simulation Mont Carlo method. It is found that the Knudsen number, the Mach number, and the angle of attack all play a mixed role in the aerodynamics of a flat plate. The ratio of lift to drag decreases as the Knudsen number increases. Studies on 3D delta wings show that the ratio of lift to drag could be increased by decreasing the wing thickness and/or by increasing the wing span. It is also found that the waveriders could produce larger ratio of lift to drag as compared with the delta wing having the same length, wing span, and cross section area.

Effects of flow regime on the young stages of Salmonid fishes. Conclusions based on results for 1977-1981

Rivers in Teesdale and its fish population have been monitored for several years. This report briefly describes the life cycle of British salmonid fishes and indicates the main ways in which this life cycle is influenced by discharge and related effects. Some highlights of the research results for 1977 - 1981 are briefly stated and proposals for future research are listed. Some practical implications of the results are discussed. (PDF contains 34 pages)

Effects of flow regime on the young stages of salmonid fishes. Summary and conclusions based on results for 1981-1985

The main British salmonid species spawn in clean gravel in streams and rivers, many of them in the upland areas of Britain. The earliest stages of the life cycle (eggs and alevins) spend some months within the gravel of the river bed. During this period their survival rate can be strongly influenced by flow regime and by related phenomena such as movement of coarse river bed material, changes in water level and the deposition of silt. In recent years human influence upon the flow regimes of upland water courses and upon the sediment inputs to them has increased. In order to conserve and, if possible, enhance the populations of salmonid fishes a deeper understanding of the interrelationships between survival of young salmonids and flow-related phenomena is needed. The acquisition of appropriate information is the main aim of the present project, which included: Studies on silt movement and the infilling of gravel voids by fine sediments, together with initial studies on the relationship between intragravel oxygen supply rate and the survival of intragravel stages of salmonids; studies in the general field of egg washout. The latter investigated the physical background to gravel bed disruption, the examination of the physical characteristics of sites chosen for redds, dimensions of redds and burial depth of eggs relative to the size of the fish constructing the redd and a series of smaller studies on other aspects of egg washout.

CFD modeling of two-phase boiling flows in the slug flow regime with an interface capturing technique

The objective of this thesis was to improve the commercial CFD software Ansys Fluent to obtain a tool able to perform accurate simulations of flow boiling in the slug flow regime. The achievement of a reliable numerical framework allows a better understanding of the bubble and flow dynamics induced by the evaporation and makes possible the prediction of the wall heat transfer trends. In order to save computational time, the flow is modeled with an axisymmetrical formulation. Vapor and liquid phases are treated as incompressible and in laminar flow. By means of a single fluid approach, the flow equations are written as for a single phase flow, but discontinuities at the interface and interfacial effects need to be accounted for and discretized properly. Ansys Fluent provides a Volume Of Fluid technique to advect the interface and to map the discontinuous fluid properties throughout the flow domain. The interfacial effects are dominant in the boiling slug flow and the accuracy of their estimation is fundamental for the reliability of the solver. Self-implemented functions, developed ad-hoc, are introduced within the numerical code to compute the surface tension force and the rates of mass and energy exchange at the interface related to the evaporation. Several validation benchmarks assess the better performances of the improved software. Various adiabatic configurations are simulated in order to test the capability of the numerical framework in modeling actual flows and the comparison with experimental results is very positive. The simulation of a single evaporating bubble underlines the dominant effect on the global heat transfer rate of the local transient heat convection in the liquid after the bubble transit. The simulation of multiple evaporating bubbles flowing in sequence shows that their mutual influence can strongly enhance the heat transfer coefficient, up to twice the single phase flow value.

Reactive mass transport modelling of a three-dimensional vertical fault zone with a finger-like convective flow regime

For a three-dimensional vertically-oriented fault zone, we consider the coupled effects of fluid flow, heat transfer and reactive mass transport, to investigate the patterns of fluid flow, temperature distribution, mineral alteration and chemically induced porosity changes. We show, analytically and numerically, that finger-like convection patterns can arise in a vertically-oriented fault zone. The onset and patterns of convective fluid flow are controlled by the Rayleigh number which is a function of the thermal properties of the fluid and the rock, the vertical temperature gradient, and the height and the permeability of the fault zone. Vigorous fluid flow causes low temperature gradients over a large region of the fault zone. In such a case, flow across lithological interfaces becomes the most important mechanism for the formation of sharp chemical reaction fronts. The degree of rock buffering, the extent and intensity of alteration, the alteration mineralogy and in some cases the formation of ore deposits are controlled by the magnitude of the flow velocity across these compositional interfaces in the rock. This indicates that alteration patterns along compositional boundaries in the rock may provide some insights into the convection pattern. The advective mass and heat exchanges between the fault zone and the wallrock depend on the permeability contrast between the fault zone and the wallrock. A high permeability contrast promotes focussed convective flow within the fault zone and diffusive exchange of heat and chemical reactants between the fault zone and the wallrock. However, a more gradual permeability change may lead to a regional-scale convective flow system where the flow pattern in the fault affects large-scale fluid flow, mass transport and chemical alteration in the wallrocks

Guidelines for the design of an environmental flow regime program at the regional scale: Application of the ELOHA framework in the Ebro River basin

La gestión de los recursos hídricos se convierte en un reto del presente y del futuro frente a un panorama de continuo incremento de la demanda de agua debido al crecimiento de la población, el crecimiento del desarrollo económico y los posibles efectos del calentamiento global. La política hidráulica desde los años 60 en España se ha centrado en la construcción de infraestructuras que han producido graves alteraciones en el régimen natural de los ríos. Estas alteraciones han provocado y acrecentado los impactos sobre los ecosistemas fluviales y ribereños. Desde los años 90, sin embargo, ha aumentado el interés de la sociedad para conservar estos ecosistemas. El concepto de caudales ambientales consiste en un régimen de caudales que simula las características principales del régimen natural. Los caudales ambientales están diseñados para conservar la estructura y funcionalidad de los ecosistemas asociados al régimen fluvial, bajo la hipótesis de que los elementos que conforman estos ecosistemas están profundamente adaptados al régimen natural de caudales, y que cualquier alteración del régimen natural puede provocar graves daños a todo el sistema. El método ELOHA (Ecological Limits of Hydrological Alteration) tiene como finalidad identificar las componentes del régimen natural de caudales que son clave para mantener el equilibrio de los ecosistemas asociados, y estimar los límites máximos de alteración de estas componentes para garantizar su buen estado. Esta tesis presenta la aplicación del método ELOHA en la cuenca del Ebro. La cuenca del Ebro está profundamente regulada e intervenida por el hombre, y sólo las cabeceras de los principales afluentes del Ebro gozan todavía de un régimen total o cuasi natural. La tesis se estructura en seis capítulos que desarrollan las diferentes partes del método. El primer capítulo explica cómo se originó el concepto “caudales ambientales” y en qué consiste el método ELOHA. El segundo capítulo describe el área de estudio. El tercer capítulo realiza una clasificación de los regímenes naturales de la cuenca (RNC) del Ebro, basada en series de datos de caudal mínimamente alterado y usando exclusivamente parámetros hidrológicos. Se identificaron seis tipos diferentes de régimen natural: pluvial mediterráneo, nivo-pluvial, pluvial mediterréaneo con una fuerte componente del caudal base, pluvial oceánico, pluvio-nival oceánico y Mediterráneo. En el cuarto capítulo se realiza una regionalización a toda la cuenca del Ebro de los seis RNC encontrados en la cueca. Mediante parámetros climáticos y fisiográficos se extrapola la información del tipo de RNC a puntos donde no existen datos de caudal inalterado. El patrón geográfico de los tipos de régimen fluvial obtenido con la regionalización resultó ser coincidente con el patrón obtenido a través de la clasificación hidrológica. El quinto capítulo presenta la validación biológica de los procesos de clasificación anteriores: clasificación hidrológica y regionalización. La validación biológica de los tipos de regímenes fluviales es imprescindible, puesto que los diferentes tipos de régimen fluvial van a servir de unidades de gestión para favorecer el mantenimiento de los ecosistemas fluviales. Se encontraron diferencias significativas entre comunidades biológicas en cinco de los seis tipos de RNC encontrados en la cuenca. Finalmente, en el sexto capítulo se estudian las relaciones hidro-ecológicas existentes en tres de los seis tipos de régimen fluvial encontrados en la cuenca del Ebro. Mediante la construcción de curvas hidro-ecológicas a lo largo de un gradiente de alteración hidrológica, se pueden sugerir los límites de alteración hidrológica (ELOHAs) para garantizar el buen estado ecológico en cada uno de los tipos fluviales estudiados. Se establecieron ELOHAs en tres de los seis tipos de RNC de la cuenca del Ebro Esta tesis, además, pone en evidencia la falta de datos biológicos asociados a registros de caudal. Para llevar a cabo la implantación de un régimen de caudales ambientales en la cuenca, la ubicación de los puntos de muestreo biológico cercanos a estaciones de aforo es imprescindible para poder extraer relaciones causa-efecto de la gestión hidrológica sobre los ecosistemas dependientes. ABSTRACT In view of a growing freshwater demand because of population raising, improvement of economies and the potential effects of climate change, water resources management has become a challenge for present and future societies. Water policies in Spain have been focused from the 60’s on constructing hydraulic infrastructures, in order to dampen flow variability and granting water availability along the year. Consequently, natural flow regimes have been deeply altered and so the depending habitats and its ecosystems. However, an increasing acknowledgment of societies for preserving healthy freshwater ecosystems started in the 90’s and agreed that to maintain healthy freshwater ecosystems, it was necessary to set environmental flow regimes based on the natural flow variability. The Natural Flow Regime paradigm (Richter et al. 1996, Poff et al. 1997) bases on the hypothesis that freshwater ecosystems are made up by elements adapted to natural flow conditions, and any change on these conditions can provoke deep impacts on the whole system. Environmental flow regime concept consists in designing a flow regime that emulates natural flow characteristics, so that ecosystem structure, functions and services are maintained. ELOHA framework (Ecological Limits of Hydrological Alteration) aims to identify key features of the natural flow regime (NFR) that are needed to maintain and preserve healthy freshwater and riparian ecosystems. Moreover, ELOHA framework aims to quantify thresholds of alteration of these flow features according to ecological impacts. This thesis describes the application of the ELOHA framework in the Ebro River Basin. The Ebro River basin is the second largest basin in Spain and it is highly regulated for human demands. Only the Ebro headwaters tributaries still have completely unimpaired flow regime. The thesis has six chapters and the process is described step by step. The first chapter makes an introduction to the origin of the environmental flow concept and the necessity to come up. The second chapter shows a description of the study area. The third chapter develops a classification of NFRs in the basin based on natural flow data and using exclusively hydrological parameters. Six NFRs were found in the basin: continental Mediterranean-pluvial, nivo-pluvial, continental Mediterranean pluvial (with groundwater-dominated flow pattern), pluvio-oceanic, pluvio-nival-oceanic and Mediterranean. The fourth chapter develops a regionalization of the six NFR types across the basin by using climatic and physiographic variables. The geographical pattern obtained from the regionalization process was consistent with the pattern obtained with the hydrologic classification. The fifth chapter performs a biological validation of both classifications, obtained from the hydrologic classification and the posterior extrapolation. When the aim of flow classification is managing water resources according to ecosystem requirements, a validation based on biological data is compulsory. We found significant differences in reference macroinvertebrate communities between five over the six NFR types identified in the Ebro River basin. Finally, in the sixth chapter we explored the existence of significant and explicative flow alteration-ecological response relationships (FA-E curves) within NFR types in the Ebro River basin. The aim of these curves is to find out thresholds of hydrological alteration (ELOHAs), in order to preserve healthy freshwater ecosystem. We set ELOHA values in three NFR types identified in the Ebro River basin. During the development of this thesis, an inadequate biological monitoring in the Ebro River basin was identified. The design and establishment of appropriate monitoring arrangements is a critical final step in the assessment and implementation of environmental flows. Cause-effect relationships between hydrology and macroinvertebrate community condition are the principal data that sustain FA-E curves. Therefore, both data sites must be closely located, so that the effects of external factors are minimized. The scarce hydro-biological pairs of data available in the basin prevented us to apply the ELOHA method at all NFR types.

Flow regime, hydrodynamics, floc size distribution and sludge properties in activated sludge bubble column, air-lift and aerated stirred reactors

This paper presents a comparative study how reactor configuration, sludge loading and air flowrate affect flow regimes, hydrodynamics, floc size distribution and sludge solids-liquid separation properties. Three reactor configurations were studied in bench scale activated sludge bubble column reactor (BCR), air-lift reactor (ALR) and aerated stirred reactor (ASR). The ASR demonstrated the highest capacity of gas holdup and resistance, and homogeneity in flow regimes and shearing forces, resulting in producing large numbers of small and compact floes. The fluid dynamics in the ALR created regularly directed recirculation forces to enhance the gas holdup and sludge flocculation. The BCR distributed a high turbulent flow regime and non-homogeneity in gas holdup and mixing, and generated large numbers of larger and looser floes. The sludge size distributions, compressibility and settleability were significantly influenced by the reactor configurations associated with the flow regimes and hydrodynamics.

Influence of the sputtering flow regime on the structural properties and magnetic behavior of Fe-Ga thin films (Ga ∼ 30 at.%)

In this paper we analyze the structure of Fe-Ga layers with a Ga content of ∼30 at.% deposited by the sputtering technique under two different regimes. We also studied the correlation between the structure and magnetic behavior of the samples. Keeping the Ar pressure fixed, we modified the flow regime from ballistic to diffusive by increasing the distance between the target and the substrate. X-ray diffraction measurements have shown a lower structural quality when growing in the diffusive flow. We investigated the impact of the growth regime by means of x-ray absorption fine structure (XAFS) measurements and obtained signs of its influence on the local atomic order. Full multiple scattering and finite difference calculations based on XAFS measurements point to a more relevant presence of a disordered A2 phase and of orthorhombic Ga clusters on the Fe-Ga alloy deposited under a diffusive regime; however, in the ballistic sample, a higher presence of D0_3/B2 phases is evidenced. Structural characteristics, from local to long range, seem to determine the magnetic behavior of the layers. Whereas a clear in-plane magnetic anisotropy is observed in the film deposited under ballistic flow, the diffusive sample is magnetically isotropic. Therefore, our experimental results provide evidence of a correlation between flow regime and structural properties and its impact on the magnetic behavior of a rather unexplored compositional region of Fe-Ga compounds.