Reproduction of recorded ocean waves in a ship model towing tank.

Mode of access: Internet.

An experimental investigation by towing tank on VIV of a long flexible cylinder for deepwater riser application

In this study, the dynamic response of a vertical flexible cylinder vibrating at low mode numbers with combined x-y motion was investigated in a towing tank. The uniform flow was simulated by towing the flexible cylinder along the tank in still water; therefore, the turbulence intensity of the free flow was negligible in obtaining more reliable results. A lower branch of dominant frequencies with micro vibration amplitude was found in both cross-flow and in-line directions. This justifiable discrepancy was likely caused by an initial lock-in. The maximum attainable amplitude, modal analysis and x-y trajectory in cross-flow and in-line directions are reported here and compared with previous literature, along with some good agreements and different observations that were obtained from the study. Drag and lift coefficients are also evaluated by making use of a generalized integral transform technique approach, yielding an alternative method to study fluid force acting upon a flexible cylinder.

Tidal Energy ”Round Robin” Tests Comparisons between towing tank and circulating tank results

One key step of the industrial development of a tidal energy device is the testing of scale prototype devices within a controlled laboratory environment. At present, there is no available experimental protocol which addresses in a quantitative manner the differences which can be expected between results obtained from the different types of facilities currently employed for this type of testing. As a consequence, where differences between results are found it has been difficult to confirm the extent to which these differences relate to the device performance or to the test facility type. In the present study, a comparative ”Round Robin” testing programme has been conducted as part of the EC FP VII MaRINET program in order to evaluate the impact of different experimental facilities on the test results. The aim of the trials was to test the same model tidal turbine in four different test facilities to explore the sensitivity of the results to the choice of facility. The facilities comprised two towing tanks, of very different size, and two circulating water channels. Performance assessments in terms of torque, drag and inflow speed showed very similar results in all facilities. However, expected differences between the different tank types (circulating and towing) were observed in the fluctuations of torque and drag measurements. The main facility parameters which can influence the behaviour of the turbine were identified; in particular the effect of blockage was shown to be significant in cases yielding for high thrust coefficients, even at relatively small blockage ratios.

Sloshing motion of water in a moonpool

This thesis is concerned with the sloshing motion of water in a moonpool. It is a relatively new problem, that is particularly predominant in moonpools with relatively large dimensions. The problem is further complicated by the additional behaviour of vertical oscillation. It is inevitable that large moonpools will be needed as offshore technology advances, therefore making a problem an important one. The research involves two parts, the theoretical and experimental study. The theoretical study consists of idealising the moonpool to a two dimensional system, represented by two surface piercing parallel barriers at a distance 2a apart. The barriers are forced to undergo roll motion which in turn generates waves. These travelling waves are travelling in opposite directions to each other and have the same amplitude and period, and thus can be expressed in terms of a standing wave. This is mathematically achieved by applying the theory of wavemaking, and therefore the wave amplitude at the side wall can be evaluated at near resonant conditions. The experimental study comprises of comparing the results obtained from the tank and moonpool experiments. The rolling motion creates the sloshing waves in both cases, in addition the vertical oscillation in the moonpool is produced by generating waves at one end of the towing tank. Apart from highlighting influencing parameters, the resonant frequencies obtained from these experiments are then compared with the theoretical values. Experiments in demonstrating the effect of increasing damping with the aid of baffles are also conducted. This is an important aspect which is very necessary if operations in launching and retrieving are to be carried out efficiently and safely.

Lift and the leading-edge vortex

Flapping wings often feature a leading-edge vortex (LEV) that is thought to enhance the lift generated by the wing. Here the lift on a wing featuring a leading-edge vortex is considered by performing experiments on a translating flat-plate aerofoil that is accelerated from rest in a water towing tank at a fixed angle of attack of 15°. The unsteady flow is investigated with dye flow visualization, particle image velocimetry (PIV) and force measurements. Leading-and trailing-edge vortex circulation and position are calculated directly from the velocity vectors obtained using PIV. In order to determine the most appropriate value of bound circulation, a two-dimensional potential flow model is employed and flow fields are calculated for a range of values of bound circulation. In this way, the value of bound circulation is selected to give the best fit between the experimental velocity field and the potential flow field. Early in the trajectory, the value of bound circulation calculated using this potential flow method is in accordance with Kelvin's circulation theorem, but differs from the values predicted by Wagner's growth of bound circulation and the Kutta condition. Later the Kutta condition is established but the bound circulation remains small; most of the circulation is contained instead in the LEVs. The growth of wake circulation can be approximated by Wagner's circulation curve. Superimposing the non-circulatory lift, approximated from the potential flow model, and Wagner's lift curve gives a first-order approximation of the measured lift. Lift is generated by inertial effects and the slow buildup of circulation, which is contained in shed vortices rather than bound circulation. © 2013 Cambridge University Press.

自由表面上球形浮体的拖曳运动仿真与试验

浮体在自由表面上的拖曳是一种常见的拖曳形式,由于自由表面上物体的运动情况相当复杂,目前对这种拖曳系统的设计和分析一般采用试验的方法。通过理论分析,对球形浮体在自由表面上的匀速直线拖曳运动建立了数学模型,其中对缆绳的分析采用Ablow-Schechter提出的有限差分模型,对球形浮体的分析采用水动力系数法,整个耦合系统用有限差分方法求解。之后,在拖曳水池进行了试验,试验结果表明,这种方法在拖曳速度比较低的情况下能够模拟真实情况,可以用来指导拖曳系统设计。

A Description of the Stationary Wave Pattern of a Marine Craft in Shallow and Intermediate Water Depths

A stationary phase model is used to study supercritical waves generated by high speed ferries. Some general relationships in terms of wave angle, propagation direction, dispersion relationship and depth wavelength relationship are explored and discussed. In particular, it is shown that the wave pattern generated by high speed craft at supercritical speeds depends mainly on the relationship of water depth and ship speed and that the wave patterns are similar in terms of location of crests and troughs for a given depth Froude number. In addition it is found that the far field wave pattern can be described adequately using a single moving point source. The theoretical model compares well with towing tank measurements and full scale data over a range of parameters and hull shapes. The paper also demonstrates that the far field wave pattern at supercritical speeds should be non-dimensionalised by water depth and not hull length unlike it is usually done for subcritical speeds.

Field testing a full-scale tidal turbine Part 2: In-line Wake Effects

Recent research has shown that higher ambient turbulence leads to better wake recovery, so turbines could be installed in closer proximity in real tidal flows than might be assumed from typical towing tank tests that do not take into account turbulent inflow conditions. The standard tools to assess flow velocities in field conditions are Doppler based sonar devices, such as Acoustic Doppler Profilers (ADPs) or Acoustic Doppler Velocimeters (ADVs). The use of these devices poses some challenges when assessing the wake of a tidal turbine. While ADPs allow the three-dimensional measurement of a velocity profile over a distance, the data is calculated as a mean of three diverging beams and with low temporal resolution. ADVs can measure with higher sampling frequency but only at a single point in the flow. During the MaRINET testing of the SCHOTTELSIT turbine at the QUB tidal test site in Portaferry, Northern Ireland, ADP and ADV measurements were successfully tested.Two methods were employed for measuring the wake: firstly, with a rigidly mounted ADP and secondly, with a submerged ADV which was streamed behind the turbine. This paper presents the experimental set-up and results and discusses limitations and challenges of the two methods used.

Experimental comparative study on vortex-induced motion (VIM) of a monocolumn platform

An analysis methodology is presented as well as a comparison of results obtained from vortex-induced motion (VIM) model tests of the MonoGoM platform, a monocolumn floating unit designed for the Gulf of Mexico. The choice of scale between the model and the platform in which the tests took place was a very important issue that took into account the basin dimensions and mooring design. The tests were performed in three different basins: the IPT Towing Tank in Brazil (Sept. 2005), the NMRI Model Ship Experimental Towing Tank in Japan (Mar. 2007), and the NMRI Experimental Tank in Japan (Jun. 2008). The purpose is to discuss the most relevant issues regarding the concept, execution, and procedures to comparatively analyze the results obtained from VIM model tests, such as characteristic motion amplitudes, motion periods, and forces. The results pointed out the importance of considering the 2DOF in the model tests, i.e., the coexistence of the motions in both in-line and transverse directions. The approach employed in the tests was designed to build a reliable data set for comparison with theoretical and numerical models for VIM prediction, especially that of monocolumn platforms. [DOI: 10.1115/1.4003494]

Effect of a propeller duct on AUV maneuverability

A number of autonomous underwater vehicles, AUV, are equipped with commercial ducted propellers, most of them produced originally for the remote operated vehicle, ROV, industry. However, AUVs and ROVs are supposed to work quite differently since the ROV operates in almost the bollard pull condition, while the AUV works at larger cruising speeds. Moreover, they can have an influence in the maneuverability of AUV due to the lift the duct generates in the most distant place of the vehicle's center of mass. In this work, it is proposed the modeling of the hydrodynamic forces and moment on a duct propeller according to a numerical (CFD) simulation, and analytical and semi-empirical, ASE, approaches. Predicted values are compared to experimental results produced in a towing tank. Results confirm the advantages of the symbiosis between CFD and ASE methods for modeling the influence of the propeller duct in the AUV maneuverability. (C) 2012 Elsevier Ltd. All rights reserved.

Numerical analysis of control surface effects on AUV

Computational fluid dynamics, CFD, is becoming an essential tool in the prediction of the hydrodynamic efforts and flow characteristics of underwater vehicles for manoeuvring studies. However, when applied to the manoeuvrability of autonomous underwater vehicles, AUVs, most studies have focused on the de- termination of static coefficients without considering the effects of the vehicle control surface deflection. This paper analyses the hydrodynamic efforts generated on an AUV considering the combined effects of the control surface deflection and the angle of attack using CFD software based on the Reynolds-averaged Navier–Stokes formulations. The CFD simulations are also independently conducted for the AUV bare hull and control surface to better identify their individual and interference efforts and to validate the simulations by comparing the experimental results obtained in a towing tank. Several simulations of the bare hull case were conducted to select the k –ω SST turbulent model with the viscosity approach that best predicts its hydrodynamic efforts. Mesh sensitivity analyses were conducted for all simulations. For the flow around the control surfaces, the CFD results were analysed according to two different methodologies, standard and nonlinear. The nonlinear regression methodology provides better results than the standard methodology does for predicting the stall at the control surface. The flow simulations have shown that the occurrence of the control surface stall depends on a linear relationship between the angle of attack and the control surface deflection. This type of information can be used in designing the vehicle’s autopilot system.

A contribution to appendage drag extrapolation using computational tools

In this paper, the foundations of the beta method, widely used in todays ship appendage extrapolations, are explored. The present work pretends to validate the Beta Method using experimental and computational tools. The ship used is a rounded bow tugboat with two significant appendages, namely, a midship protective structure for the propulsion system and a stern keel. The experimental and computational data was obtained through Towing Tank trials and a RANSE CFD code, respectively.

Numerical and experimental study of appendages in racing yachts and their influence on the free surface

Las prestaciones de un velero de regatas se estiman por medio de los Programas de Predicción de Velocidad (VPP) que incluyen las características de estabilidad y modelos aero e hidrodinámico del barco. Por esta razón, es importante tener una evaluación adecuada de las fuerzas en apéndices y de su variación en diferentes condiciones de navegación, escora y deriva. Además, para el cálculo de las fuerzas en los apéndices es importante conocer sus características hidrodinámicas cuando trabajan conjuntamente en un campo fluido fuertemente modificado por la carena. Por esta razón, se han utilizado una serie de ensayos realizados en el Canal de Ensayos de la ETSIN con el objetivo de validar códigos numéricos que permiten una evaluación más rápida y focalizada en los distintos fenómenos que se producen. Dichos ensayos se han realizado de forma que pudiera medirse independientemente las fuerzas hidrodinámicas en cada apéndice, lo que permitirá evaluar el reparto de fuerzas en diferentes condiciones de navegación para poder profundizar en las interacciones entre carena, quilla y timón. Las técnicas numéricas permiten capturar detalles que difícilmente se pueden visualizar en ensayos experimentales. En este sentido, se han probado las últimas técnicas utilizadas en los últimos workshops y se ha enfocado el estudio a un nuevo método con el objetivo de mostrar una metodologia más rápida que pueda servir a la industria para este tipo de aproximación al problema. ABSTRACT The performances of a racing sailboat are estimated by means of the speed prediction programs (VPP), which include the ship stability characteristics and the aero and hydrodynamic models. For this reason, it is important to have an adequate evaluation of the forces in appendices and its variation in different sailing conditions, heel and leeway Moreover, for the analysis of the forces in the appendices, it is important to know their hydrodynamic characteristics when they work together in a fluid field strongly modified by the canoe body. For this reason, several tests have been done in the ETSIN towing tank with the aim to validate numeric codes that allowing faster analysis and they permit to focus on the different phenomena that occur there. Such tests have been done in a way that the hydrodynamic forces in each appendage could be measured independently allowing assessing the distribution of forces in different sailing conditions to be able to deepen the interactions between the canoe body, the keel and the rudder. Numerical techniques allow capturing details that can hardly be displayed in experimental tests. In this sense, the latest techniques used in the recent workshops have been reviewed and the study has been focused to propose a new model with the aim to show a new faster methodology which serves the industry for this type of approach to the problem.

Fenómenos dinámicos de estabilidad de un buque en olas longitudinales: resonancia paramétrica. Influencia en el proyecto y equipo. Guía operacional al capitán

El fenómeno de balance paramétrico se ha convertido en un tema de actualidad en los últimos años debido al aumento de accidentes relacionados y las discusiones en OMI debido a su indiscutible importancia en la seguridad del buque, su carga y tripulación. Por esta razón, su estudio ha atraído el interés de universidades, administraciones y sociedades de clasificación. Esta tesis trata el fenómeno de balance paramétrico desde diferentes puntos de vista. Primero, se estudiaran los diferentes escenarios donde el fenómeno de balance paramétrico ha ocurrido para entender cómo se desarrolla el fenómeno en la vida real, así como sus implicaciones en la seguridad de las personas y carga abordo. Un modelo matemático no lineal de movimiento de balance desacoplado es propuesto. Este modelo se basa en la aproximación cuadrática del momento de amortiguamiento junto con un brazo adrizante dependiente del tiempo. Este modelo es validado con datos experimentales del Canal de Ensayos de la ETSI Navales (UPM) relativos a un buque de pesca de 34.5m de eslora y dos cubiertas para diferentes casos de olas longitudinales. Se encuentra una correspondencia muy satisfactoria en términos de fase y amplitud entre el modelo teórico y los datos de canal para el caso en particular. El modelo es comparado con el estado del arte de la tecnología disponible actualmente, así como con los requisitos mínimos que están siendo discutidos en OMI relativos a los Criterios de Estabilidad de Segunda Generación. Finalmente, el fenómeno es revisado desde los puntos de vista de diseño y operacional para entender los parámetros relevantes detrás del fenómeno y conocer/aplicar las herramientas disponibles y medios para afrontar/mitigar este fenómeno. ABSTRACT A parametric roll resonance phenomenon has become a very relevant technical issue in recent years due the increasing number of accidents related and the ongoing discussions at the IMO due to its undisputed importance in the safety of the ship, its cargo and crew. For this reason, its study has attracted the interest of universities, regulatory bodies and classification societies. This thesis deals with this phenomenon of parametric roll resonance from different points of view. First, we will look at different real scenarios where parametric roll resonance phenomena has occurred in order to further understand how it is developed in real life and its implications for the safety of the people and cargo onboard. A non-linear mathematical model of the uncoupled roll motion is also presented. This model is based on a classic quadratic approximation of the damping momentum together with a time-varying restoring arm. This model is validated with real data taken from experimental results of the E.T.S.I. Navales Towing Tank on a trawler of two decks of 34.5 m. length for different cases of longitudinal waves. A very satisfactory correspondence, in terms of phase and amplitude, is found between the theoretical model presented and the real data on this particular case. The model is compare with the state-of-the-art technology currently available as well as with the minimum requirements currently being discussed as part of the IMO SGISC. Finally, the phenomenon is reviewed from design and operational aspects to understand the underlying parameters and know the available tools and ways to tackle/mitigate this phenomenon.