Multilevel high-voltage pulse generation based on a new modular solid-state switch

This paper describes a modular solid-state switching cell derived from the Marx generator concept to be used in topologies for generating multilevel unipolar and bipolar high-voltage (HV) pulses into resistive loads. The switching modular cell comprises two ON/OFF semiconductors, a diode, and a capacitor. This cell can be stacked, being the capacitors charged in series and their voltages balanced in parallel. To balance each capacitor voltage without needing any parameter measurement, a vector decision diode algorithm is used in each cell to drive the two switches. Simulation and experimental results, for generating multilevel unipolar and bipolar HV pulses into resistive loads are presented.

Design of Novel Frequency Generation Circuit with Application to Ultra-Wideband Distributed Oscillators

Given the urgence of a new paradigm in wireless digital trasmission which should allow for higher bit rate, lower latency and tigher delay constaints, it has been proposed to investigate the fundamental building blocks that at the circuital/device level, will boost the change towards a more efficient network architecture, with high capacity, higher bandwidth and a more satisfactory end user experience. At the core of each transciever, there are inherently analog devices capable of providing the carrier signal, the oscillators. It is strongly believed that many limitations in today's communication protocols, could be relieved by permitting high carrier frequency radio transmission, and having some degree of reconfigurability. This led us to studying distributed oscillator architectures which work in the microwave range and possess wideband tuning capability. As microvave oscillators are essentially nonlinear devices, a full nonlinear analyis, synthesis, and optimization had to be considered for their implementation. Consequently, all the most used nonlinear numerical techniques in commercial EDA software had been reviewed. An application of all the aforementioned techniques has been shown, considering a systems of three coupled oscillator ("triple push" oscillator) in which the stability of the various oscillating modes has been studied. Provided that a certain phase distribution is maintained among the oscillating elements, this topology permits a rise in the output power of the third harmonic; nevertheless due to circuit simmetry, "unwanted" oscillating modes coexist with the intenteded one. Starting with the necessary background on distributed amplification and distributed oscillator theory, the design of a four stage reverse mode distributed voltage controlled oscillator (DVCO) using lumped elments has been presented. All the design steps have been reported and for the first time a method for an optimized design with reduced variations in the output power has been presented. Ongoing work is devoted to model a wideband DVCO and to implement a frequency divider.

Melt topology and chemistry during partial melting in contact aureoles : an experimental study and field example

This study was initiated to investigate partial melting within the high-grade metamorphic rocks beneath the Little Cottonwood contact aureole (Utah, USA), in order to understand the melt generation, melt migration, and geometry of initial melt distribution on grain scale during crustal anatexis. The emplacement of the Little Cottonwood stock produced a contact aureole in the pelitic host rocks of the Big Cottonwood formation (BC). Metamorphic isogrades in pelitic rocks range form biotite to 2nd sillimanite grade as a function of distance from the contact. Migmatites are restricted to the highest grade and resulted form partial melting of the BC formation rocks. First melt was produced by a combined muscovite/biotite dehydration reaction in the sillimanite + k-feldspar stability field. Melt extraction from the pelites resulted in restites (magnetite + cordierite + alumosilicate ± biotite) surrounded by feldspar enriched quartzite zones. This texture is the result of gradual infiltration of partial melts into the quartzite. Larger, discrete melt accumulation occurred in extensional or transpressional domains such as boudin necks, veins, and ductile shear zones. Melt composition are Si02- rich, crystallized as pegmatites, and apparently were very mobile. They were able to infiltrate the quartzite pervaisivly. These melts are similar in composition to first melts produced in the hydrothermal partial melt experiments at 2kbar between 700 - 800°C on fine grained high metamorphic rocks (andalusite-cordierited-biotite-zone) of the BC formation. The experimental melts are water rich and in disequilibrium with the melting rock. Initial melt composition is heterogeneous for short run duration, reflective a lack of chemical equilibrium between individual melt pools. Rock core scale heterogeneity decreased with time indicating partial homogenization of melt compositions. A simultaneous shift of melt composition to higher silica content with time was observed. The silica content of the melt increased due to local melt/mineral reactions. Melt textures indicate that reactive melt transport is most efficient along grain boundaries rimmed by dissimilar grains. Melt heterogeneity resulted in chemical potential gradients which are major driving forces for initial melt migration and govern melt distribution during initial melting. An additional subject of the thesis is the crystal size distributions of opaque minerals in a fine-grained, high-grade meta-pelite of the Big Cottonwood which were obtained from 3D X-ray tomography (uCT) and 2D thin section analysis. µCT delivers accurate size distributions within a restricted range (~ a factor of 20 in size in a single 3D image), while the absolute number of crystals is difficult to obtain from these sparsely distributed, small crystals on the basis of 2D images. Crystal size distributions obtained from both methods are otherwise similar. - Ce travail de recherche a été entrepris dans le but d'étudier les processus de fusion partielle dans les roches fortement métamorphiques de l'auréole de contact de Little Cottonwood (Utah, USA) et ceci afin de comprendre la génération de liquide de fusion, la migration de ces liquides et la géométrie de la distribution initiale des liquides de fusion à l'échelle du grain durant l'anatexie de la croûte. L'emplacement du petit massif intrusif de Little Cottonwood a produit une auréole de contact dans les roches pélitiques encaissantes appartenant à la Foimation du Big Cottonwood (BC). Les isogrades métamorphiques dans les roches pélitiques varient de l'isograde de la biotite à la deuxième isograde de la sillimanite en fonction de la distance par rapport au massif intrusif. Les migmatites sont restreintes aux zones montrant le plus haut degré métamorphique et résultent de la fusion partielle des roches de la Formation de BC. Le premier liquide de fusion a été produit par la réaction de déshydratation combinée de la muscovite et de la biotite dans le champ de stabilité du feldspath potassique Pt de la sillimanite. L'extraction du liquide de fusion des pélites forme des restites (magnétites + cordiérite + aluminosilicate ± biotite) entourées par des zones de quartzites enrichies en feldspath. Cette texture est le résultat de l'infiltration graduelle du liquide de fusion partielle dans les quartzites. Des accumulations distinctes et plus larges de liquide de fusion ont lieu dans des domaines d'extension ou de transpression tels que les boudins, les veines, et les zones de cisaillement ductile. La composition des liquides de fusion est similaire à celle des liquides pegmatoïdes, et ces liquides sont apparemment très mobiles et capables d'infiltrer les quartzites. Ces liquides de fusion ont la même composition que les premiers liquides produits dans les expériences hydrotheunales de fusion partielle à 2kbar et entre 700-800° C sur les roches finement grenues et hautement métamorphiques (andalousite-cordiérite-biotite zone) de la Formation de BC. Les liquides de fusion obtenus expérimentalement sont riches en eau et sont en déséquilibre avec la roche en fusion. La composition initiale des liquides de fusion est hétérogène pour les expériences de courte durée et reflète l'absence d'équilibre chimique entre les différentes zones d'accumulation des liquides de fusion. L'hétérogénéité à l'échelle du noyau s'estompe avec le temps et témoigne de l'homogénéisation de la composition des liquides de fusion. Par ailleurs, on observe parallèlement un décalage de la composition des liquides vers des compositions plus riches en silice au cours du temps. Le contenu en silice des liquides de fusion évolue vers un liquide pegmatitique en raison des réactions liquides/minéraux. Les textures des liquides de fusion indiquent que le transport des liquides est plus efficace le long des bordures de grains bordés par des grains différents. Aucun changement apparent du volume total n'est visible. L'hétérogénéité des liquides s'accompagne d'un gradient de potentiel chimique qui sert de moteur principal à la migration des liquides et à la distribution des liquides durant la fusion. Un sujet complémentaire de ce travail de thèse réside dans l'étude de la distribution de la taille des cristaux opaques dans les pélites finement grenues et fortement métamorphiques de la Formation de Big Cottonwood. Les distributions de taille ont été obtenues suite à l'analyse d'images 3D acquise par tomographie ainsi que par analyse de lames minces. La microtomographie par rayon X fournit une distribution de taille précise sur une marge restreinte (- un facteur de taille 20 dans une seule image 3D), alors que le nombre absolu de cristaux est difficile à obtenir sur la base d'image 2D en raison de la petite taille et de la faible abondance de ces cristaux. Les distributions de taille obtenues par les deux méthodes sont sinon similaire. Abstact: Chemical differentiation of the primitive Earth was due to melting and separation of melts. Today, melt generation and emplacement is still the dominant process for the growth of the crust. Most granite formation is due to partial melting of the lower crust, followed by transport of magma through the crust to the shallow crust where it is emplaced. Partial melting and melt segregation are essential steps before such a granitic magma can ascent through the crust. The chemistry and physics of partial melting and segregation is complex. Hence detailed studies, in which field observations yield critical information that can be compared to experimental observations, are crucial to the understanding of these fundamental processes that lead and are leading to the chemical stratification of the Earth. The research presented in this thesis is a combined field and experimental study of partial melting of high-grade meta-pelitic rocks of the Little Cottonwood contact aureole (Utah, USA). Contact metamorphic rocks are ideal for textural studies of melt generation, since the relatively short times of the metamorphic event prevents much of the recrystallization which plagues textural studies of lower crustal rocks. The purpose of the study is to characterize melt generation, identify melting reactions, and to constrain melt formation, segregation and migration mechanisms. In parallel an experimental study was undertaken to investigate melt in the high grade meta pelitic rocks, to confirm melt composition, and to compare textures of the partial molten rock cores in the absence of deformation. Results show that a pegmatoidal melt is produced by partial melting of the pelitic rocks. This melt is highly mobile. It is capable of pervasive infiltration of the adjacent quartzite. Infiltration results in rounded quartz grains bordered by a thin feldspar rim. Using computed micro X-ray tomography these melt networks can be imaged. The infiltrated melt leads to rheological weakening and to a decompaction of the solid quartzite. Such decompaction can explain the recent discovery of abundant xenocrysts in many magmas, since it favors the isolation of mineral grains. Pervasive infiltration is apparently strongly influenced by melt viscosity and melt-crystal wetting behavior, both of which depend on the water content of melt and the temperature. In all experiments the first melt is produced on grain boundaries, dominantly by the local minerals. Grain scale heterogeneity of a melting rock leads thus to chemical concentration gradients in the melt, which are the driving force for initial melt migration. Pervasive melt films along grain boundaries leading to an interconnected network are immediately established. The initial chemical heterogeneities in the melt diminish with time. Résumé large public: La différenciation chimique de la Terre primitive est la conséquence de la fusion des roches et de la séparation des liquides qui en résultent. Aujourd'hui, la production de liquide magmatique est toujours le mécanisme dominant pour la croissance de la croûte terrestre. Ainsi la formation de la plupart des granites est un processus qui implique la production de magma par fusion partielle de la croûte inférieure, la migration de ces magmas à travers la croûte et finalement son emplacement dans les niveaux superficielle de la croûte terrestre. Au cours de cette évolution, les processus de fusion partielle et de ségrégation sont des étapes indispensables à l'ascension des granites à travers la croûte. Les conditions physico-chimiques nécessaires à la fusion partielle et à l'extraction de ces liquides sont complexes. C'est pourquoi des études détaillées des processus de fusion partielle sont cruciales pour la compréhension de ces mécanismes fondamentaux responsables de la stratification chimique de la Terre. Parmi ces études, les observations de terrain apportent notamment des informations déterminantes qui peuvent être comparées aux données expérimentales. Le travail de recherche présenté dans ce mémoire de thèse associe études de terrain et données expérimentales sur la fusion partielle des roches pélitiques de haut degré métamorphiques provenant de l'auréole de contact de Little Cottonwood (Utah, USA). Les roches du métamorphisme de contact sont idéales pour l'étude de la folination de liquide de fusion. En effet, la durée relativement courte de ce type d'événement métamorphique prévient en grande partie la recristallisation qui perturbe les études de texture des roches dans la croûte inférieure. Le but de cette étude est de caractériser la génération des liquides de fusion, d'identifier les réactions responsables de la fusion de ces roches et de contraindre la formation de ces liquides et leur mécanisme de ségrégation et de migration. Parallèlement, des travaux expérimentaux ont été entrepris pour reproduire la fusion partielle de ces roches en laboratoire. Cette étude a été effectuée dans le but de confirmer la composition chimique des liquides, et de comparer les textures obtenues en l'absence de déformation. Les résultats montrent qu'un liquide de fusion pegmatoïde est produit par fusion partielle des roches pélitiques. La grande mobilité de ce liquide permet une infiltration pénétrative dans les quarzites. Ces infiltrations se manifestent par des grains de quartz arrondis entourés par une fine bordure de feldspath. L'utilisation de la tomography à rayons X a permis d'obtenir des images de ce réseau de liquide de fusion. L'infiltration de liquide de fusion entraîne un affaiblissement de la rhéologie de la roche ainsi qu'une décompaction des quartzites massifs. Une telle décompaction peut expliquer la découverte récente d'abondants xénocristaux dans beaucoup de magmas, puisque elle favorise l'isolation des minéraux. L'infiltration pénétrative est apparemment fortement influencée par la viscosité du fluide de fusion et le comportement de la tension superficielle entre les cristaux et le liquide, les deux étant dépendant du contenu en eau dans le liquide de fusion et de la température. Dans toutes les expériences, le premier liquide est produit sur les bordures de grains, principalement par les minéraux locaux. L'hétérogénéité à l'échelle des grains d'une roche en fusion conduit donc à un gradient de concentration chimique dans le liquide, qui sert de moteur à l'initiation de la migration du liquide. Des fines couches de liquide de fusion le long de bordures de grains formant un réseau enchevêtré s'établit immédiatement. Les hétérogénéités chimiques initiales dans le liquide s'estompent avec le temps.

Report on theorerical results of power generation and conversion

Experimental results of a new controller able to support bidirectional power flow in a full-bridge rectifier with boost-like topology are obtained. The controller is computed using port Hamiltonian passivity techniques for a suitable generalized state space averaging truncation system, which transforms the control objectives, namely constant output voltage dc-bus and unity input power factor, into a regulation problem. Simulation results for the full system show the essential correctness of the simplifications introduced to obtain the controller, although some small experimental discrepancies point to several aspects that need further improvement.

Performance Management of a Next Generation Network

Today's communication networks consist of numerous interdependent network components. To manage these networks and to ensure their reliable and efficient operation to meet the increasing customer usability demands, extensive network management tools are required from the service provider. The goal of this study was to adapt the Next Generation Network (NGN) providing VoIP services within a performance oriented network management system. This study focuses only on NGN network and the project was implemented as an assignment of the Network Operations Center of Elisa Corporation. The theoretical part of this study introduces the network environment of the Elisa NGN platform: its components and used signalling protocols as well as other exploitable communication protocols. In addition, the Simple Network Management Protocol (SNMP) is closely examined since it is commonly used as the basis of IP (Internet Protocol) network management. Also some primary applications enabled by the NGN technology are introduced. The empirical part of this study contains a short overview of the implemented network performance management system and its properties. The most crucial monitored MIB modules, SNMP parameters and implemented performance measurements are described. The trap topology and the role of the traps for management of the NGN platform are considered and finally, the conclusion based on the several disquisitions is made supported with suggestions for future improvements.

Transmission network expansion planning considering uncertainty in generation and demand

This paper presents a mathematical model and a methodology to solve a transmission network expansion planning problem considering uncertainty in demand and generation. The methodology used to solve the problem, finds the optimal transmission network expansion plan that allows the power system to operate adequately in an environment with uncertainty. The model presented results in an optimization problem that is solved using a specialized genetic algorithm. The results obtained for known systems from the literature show that cheaper plans can be found satisfying the uncertainty in demand and generation. ©2008 IEEE.

Transmission network expansion planning considering multiple generation scenarios

This paper presents a mathematical model and a methodology to solve a transmission network expansion planning problem considering open access. The methodology finds the optimal transmission network expansion plan that allows the power system to operate adequately in an environment with multiples generation scenarios. The model presented is solved using a specialized genetic algorithm. The methodology is tested in a system from the literature. ©2008 IEEE.

Topology Verification for Isosurface Extraction

The broad goals of verifiable visualization rely on correct algorithmic implementations. We extend a framework for verification of isosurfacing implementations to check topological properties. Specifically, we use stratified Morse theory and digital topology to design algorithms which verify topological invariants. Our extended framework reveals unexpected behavior and coding mistakes in popular publicly available isosurface codes.

Hall-effect thruster-cathode coupling : the effect of cathode position and magnetic field topology

Hall-effect thruster (HET) cathodes are responsible for the generation of the free electrons necessary to initiate and sustain the main plasma discharge and to neutralize the ion beam. The position of the cathode relative to the thruster strongly affects the efficiency of thrust generation. However, the mechanisms by which the position affects the efficiency are not well understood. This dissertation explores the effect of cathode position on HET efficiency. Magnetic field topology is shown to play an important role in the coupling between the cathode plasma and the main discharge plasma. The position of the cathode within the magnetic field affects the ion beam and the plasma properties of the near-field plume, which explains the changes in efficiency of the thruster. Several experiments were conducted which explored the changes of efficiency arising from changes in cathode coupling. In each experiment, the thrust, discharge current, and cathode coupling voltage were monitored while changes in the independent variables of cathode position, cathode mass flow and magnetic field topology were made. From the telemetry data, the efficiency of the HET thrust generation was calculated. Furthermore, several ion beam and plasma properties were measured including ion energy distribution, beam current density profile, near-field plasma potential, electron temperature, and electron density. The ion beam data show how the independent variables affected the quality of ion beam and therefore the efficiency of thrust generation. The measurements of near-field plasma properties partially explain how the changes in ion beam quality arise. The results of the experiments show that cathode position, mass flow, and field topology affect several aspects of the HET operation, especially beam divergence and voltage utilization efficiencies. Furthermore, the experiments show that magnetic field topology is important in the cathode coupling process. In particular, the magnetic field separatrix plays a critical role in impeding the coupling between cathode and HET. Suggested changes to HET thruster designs are provided including ways to improve the position of the separatrix to accommodate the cathode.

NETWORK TOPOLOGY IN HUMAN PROTEIN INTERACTION DATA PREDICTS FUNCTIONAL ASSOCIATION

High-throughput assays, such as yeast two-hybrid system, have generated a huge amount of protein-protein interaction (PPI) data in the past decade. This tremendously increases the need for developing reliable methods to systematically and automatically suggest protein functions and relationships between them. With the available PPI data, it is now possible to study the functions and relationships in the context of a large-scale network. To data, several network-based schemes have been provided to effectively annotate protein functions on a large scale. However, due to those inherent noises in high-throughput data generation, new methods and algorithms should be developed to increase the reliability of functional annotations. Previous work in a yeast PPI network (Samanta and Liang, 2003) has shown that the local connection topology, particularly for two proteins sharing an unusually large number of neighbors, can predict functional associations between proteins, and hence suggest their functions. One advantage of the work is that their algorithm is not sensitive to noises (false positives) in high-throughput PPI data. In this study, we improved their prediction scheme by developing a new algorithm and new methods which we applied on a human PPI network to make a genome-wide functional inference. We used the new algorithm to measure and reduce the influence of hub proteins on detecting functionally associated proteins. We used the annotations of the Gene Ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) as independent and unbiased benchmarks to evaluate our algorithms and methods within the human PPI network. We showed that, compared with the previous work from Samanta and Liang, our algorithm and methods developed in this study improved the overall quality of functional inferences for human proteins. By applying the algorithms to the human PPI network, we obtained 4,233 significant functional associations among 1,754 proteins. Further comparisons of their KEGG and GO annotations allowed us to assign 466 KEGG pathway annotations to 274 proteins and 123 GO annotations to 114 proteins with estimated false discovery rates of <21% for KEGG and <30% for GO. We clustered 1,729 proteins by their functional associations and made pathway analysis to identify several subclusters that are highly enriched in certain signaling pathways. Particularly, we performed a detailed analysis on a subcluster enriched in the transforming growth factor β signaling pathway (P<10-50) which is important in cell proliferation and tumorigenesis. Analysis of another four subclusters also suggested potential new players in six signaling pathways worthy of further experimental investigations. Our study gives clear insight into the common neighbor-based prediction scheme and provides a reliable method for large-scale functional annotations in this post-genomic era.

A swarm intelligence approach based on coupled oscillators: an application in demand side management with photovoltaic distributed generation

Esta Tesis aborda los problemas de eficiencia de las redes eléctrica desde el punto de vista del consumo. En particular, dicha eficiencia es mejorada mediante el suavizado de la curva de consumo agregado. Este objetivo de suavizado de consumo implica dos grandes mejoras en el uso de las redes eléctricas: i) a corto plazo, un mejor uso de la infraestructura existente y ii) a largo plazo, la reducción de la infraestructura necesaria para suplir las mismas necesidades energéticas. Además, esta Tesis se enfrenta a un nuevo paradigma energético, donde la presencia de generación distribuida está muy extendida en las redes eléctricas, en particular, la generación fotovoltaica (FV). Este tipo de fuente energética afecta al funcionamiento de la red, incrementando su variabilidad. Esto implica que altas tasas de penetración de electricidad de origen fotovoltaico es perjudicial para la estabilidad de la red eléctrica. Esta Tesis trata de suavizar la curva de consumo agregado considerando esta fuente energética. Por lo tanto, no sólo se mejora la eficiencia de la red eléctrica, sino que también puede ser aumentada la penetración de electricidad de origen fotovoltaico en la red. Esta propuesta conlleva grandes beneficios en los campos económicos, social y ambiental. Las acciones que influyen en el modo en que los consumidores hacen uso de la electricidad con el objetivo producir un ahorro energético o un aumento de eficiencia son llamadas Gestión de la Demanda Eléctrica (GDE). Esta Tesis propone dos algoritmos de GDE diferentes para cumplir con el objetivo de suavizado de la curva de consumo agregado. La diferencia entre ambos algoritmos de GDE reside en el marco en el cual estos tienen lugar: el marco local y el marco de red. Dependiendo de este marco de GDE, el objetivo energético y la forma en la que se alcanza este objetivo son diferentes. En el marco local, el algoritmo de GDE sólo usa información local. Este no tiene en cuenta a otros consumidores o a la curva de consumo agregado de la red eléctrica. Aunque esta afirmación pueda diferir de la definición general de GDE, esta vuelve a tomar sentido en instalaciones locales equipadas con Recursos Energéticos Distribuidos (REDs). En este caso, la GDE está enfocada en la maximización del uso de la energía local, reduciéndose la dependencia con la red. El algoritmo de GDE propuesto mejora significativamente el auto-consumo del generador FV local. Experimentos simulados y reales muestran que el auto-consumo es una importante estrategia de gestión energética, reduciendo el transporte de electricidad y alentando al usuario a controlar su comportamiento energético. Sin embargo, a pesar de todas las ventajas del aumento de auto-consumo, éstas no contribuyen al suavizado del consumo agregado. Se han estudiado los efectos de las instalaciones locales en la red eléctrica cuando el algoritmo de GDE está enfocado en el aumento del auto-consumo. Este enfoque puede tener efectos no deseados, incrementando la variabilidad en el consumo agregado en vez de reducirlo. Este efecto se produce porque el algoritmo de GDE sólo considera variables locales en el marco local. Los resultados sugieren que se requiere una coordinación entre las instalaciones. A través de esta coordinación, el consumo debe ser modificado teniendo en cuenta otros elementos de la red y buscando el suavizado del consumo agregado. En el marco de la red, el algoritmo de GDE tiene en cuenta tanto información local como de la red eléctrica. En esta Tesis se ha desarrollado un algoritmo autoorganizado para controlar el consumo de la red eléctrica de manera distribuida. El objetivo de este algoritmo es el suavizado del consumo agregado, como en las implementaciones clásicas de GDE. El enfoque distribuido significa que la GDE se realiza desde el lado de los consumidores sin seguir órdenes directas emitidas por una entidad central. Por lo tanto, esta Tesis propone una estructura de gestión paralela en lugar de una jerárquica como en las redes eléctricas clásicas. Esto implica que se requiere un mecanismo de coordinación entre instalaciones. Esta Tesis pretende minimizar la cantidad de información necesaria para esta coordinación. Para lograr este objetivo, se han utilizado dos técnicas de coordinación colectiva: osciladores acoplados e inteligencia de enjambre. La combinación de estas técnicas para llevar a cabo la coordinación de un sistema con las características de la red eléctrica es en sí mismo un enfoque novedoso. Por lo tanto, este objetivo de coordinación no es sólo una contribución en el campo de la gestión energética, sino también en el campo de los sistemas colectivos. Los resultados muestran que el algoritmo de GDE propuesto reduce la diferencia entre máximos y mínimos de la red eléctrica en proporción a la cantidad de energía controlada por el algoritmo. Por lo tanto, conforme mayor es la cantidad de energía controlada por el algoritmo, mayor es la mejora de eficiencia en la red eléctrica. Además de las ventajas resultantes del suavizado del consumo agregado, otras ventajas surgen de la solución distribuida seguida en esta Tesis. Estas ventajas se resumen en las siguientes características del algoritmo de GDE propuesto: • Robustez: en un sistema centralizado, un fallo o rotura del nodo central provoca un mal funcionamiento de todo el sistema. La gestión de una red desde un punto de vista distribuido implica que no existe un nodo de control central. Un fallo en cualquier instalación no afecta el funcionamiento global de la red. • Privacidad de datos: el uso de una topología distribuida causa de que no hay un nodo central con información sensible de todos los consumidores. Esta Tesis va más allá y el algoritmo propuesto de GDE no utiliza información específica acerca de los comportamientos de los consumidores, siendo la coordinación entre las instalaciones completamente anónimos. • Escalabilidad: el algoritmo propuesto de GDE opera con cualquier número de instalaciones. Esto implica que se permite la incorporación de nuevas instalaciones sin afectar a su funcionamiento. • Bajo coste: el algoritmo de GDE propuesto se adapta a las redes actuales sin requisitos topológicos. Además, todas las instalaciones calculan su propia gestión con un bajo requerimiento computacional. Por lo tanto, no se requiere un nodo central con un alto poder de cómputo. • Rápido despliegue: las características de escalabilidad y bajo coste de los algoritmos de GDE propuestos permiten una implementación rápida. No se requiere una planificación compleja para el despliegue de este sistema. ABSTRACT This Thesis addresses the efficiency problems of the electrical grids from the consumption point of view. In particular, such efficiency is improved by means of the aggregated consumption smoothing. This objective of consumption smoothing entails two major improvements in the use of electrical grids: i) in the short term, a better use of the existing infrastructure and ii) in long term, the reduction of the required infrastructure to supply the same energy needs. In addition, this Thesis faces a new energy paradigm, where the presence of distributed generation is widespread over the electrical grids, in particular, the Photovoltaic (PV) generation. This kind of energy source affects to the operation of the grid by increasing its variability. This implies that a high penetration rate of photovoltaic electricity is pernicious for the electrical grid stability. This Thesis seeks to smooth the aggregated consumption considering this energy source. Therefore, not only the efficiency of the electrical grid is improved, but also the penetration of photovoltaic electricity into the grid can be increased. This proposal brings great benefits in the economic, social and environmental fields. The actions that influence the way that consumers use electricity in order to achieve energy savings or higher efficiency in energy use are called Demand-Side Management (DSM). This Thesis proposes two different DSM algorithms to meet the aggregated consumption smoothing objective. The difference between both DSM algorithms lie in the framework in which they take place: the local framework and the grid framework. Depending on the DSM framework, the energy goal and the procedure to reach this goal are different. In the local framework, the DSM algorithm only uses local information. It does not take into account other consumers or the aggregated consumption of the electrical grid. Although this statement may differ from the general definition of DSM, it makes sense in local facilities equipped with Distributed Energy Resources (DERs). In this case, the DSM is focused on the maximization of the local energy use, reducing the grid dependence. The proposed DSM algorithm significantly improves the self-consumption of the local PV generator. Simulated and real experiments show that self-consumption serves as an important energy management strategy, reducing the electricity transport and encouraging the user to control his energy behavior. However, despite all the advantages of the self-consumption increase, they do not contribute to the smooth of the aggregated consumption. The effects of the local facilities on the electrical grid are studied when the DSM algorithm is focused on self-consumption maximization. This approach may have undesirable effects, increasing the variability in the aggregated consumption instead of reducing it. This effect occurs because the algorithm only considers local variables in the local framework. The results suggest that coordination between these facilities is required. Through this coordination, the consumption should be modified by taking into account other elements of the grid and seeking for an aggregated consumption smoothing. In the grid framework, the DSM algorithm takes into account both local and grid information. This Thesis develops a self-organized algorithm to manage the consumption of an electrical grid in a distributed way. The goal of this algorithm is the aggregated consumption smoothing, as the classical DSM implementations. The distributed approach means that the DSM is performed from the consumers side without following direct commands issued by a central entity. Therefore, this Thesis proposes a parallel management structure rather than a hierarchical one as in the classical electrical grids. This implies that a coordination mechanism between facilities is required. This Thesis seeks for minimizing the amount of information necessary for this coordination. To achieve this objective, two collective coordination techniques have been used: coupled oscillators and swarm intelligence. The combination of these techniques to perform the coordination of a system with the characteristics of the electric grid is itself a novel approach. Therefore, this coordination objective is not only a contribution in the energy management field, but in the collective systems too. Results show that the proposed DSM algorithm reduces the difference between the maximums and minimums of the electrical grid proportionally to the amount of energy controlled by the system. Thus, the greater the amount of energy controlled by the algorithm, the greater the improvement of the efficiency of the electrical grid. In addition to the advantages resulting from the smoothing of the aggregated consumption, other advantages arise from the distributed approach followed in this Thesis. These advantages are summarized in the following features of the proposed DSM algorithm: • Robustness: in a centralized system, a failure or breakage of the central node causes a malfunction of the whole system. The management of a grid from a distributed point of view implies that there is not a central control node. A failure in any facility does not affect the overall operation of the grid. • Data privacy: the use of a distributed topology causes that there is not a central node with sensitive information of all consumers. This Thesis goes a step further and the proposed DSM algorithm does not use specific information about the consumer behaviors, being the coordination between facilities completely anonymous. • Scalability: the proposed DSM algorithm operates with any number of facilities. This implies that it allows the incorporation of new facilities without affecting its operation. • Low cost: the proposed DSM algorithm adapts to the current grids without any topological requirements. In addition, every facility calculates its own management with low computational requirements. Thus, a central computational node with a high computational power is not required. • Quick deployment: the scalability and low cost features of the proposed DSM algorithms allow a quick deployment. A complex schedule of the deployment of this system is not required.

A socio-economic approach to online vision graph generation and handover in distributed smart camera networks

In this paper we propose an approach based on self-interested autonomous cameras, which exchange responsibility for tracking objects in a market mechanism, in order to maximise their own utility. A novel ant-colony inspired mechanism is used to grow the vision graph during runtime, which may then be used to optimise communication between cameras. The key benefits of our completely decentralised approach are on the one hand generating the vision graph online which permits the addition and removal cameras to the network during runtime and on the other hand relying only on local information, increasing the robustness of the system. Since our market-based approach does not rely on a priori topology information, the need for any multi-camera calibration can be avoided. © 2011 IEEE.

Generation and performance of localised surface plasmons utilising nano-scale structured multi-layered thin films deposited upon D-shaped optical fiber

A new generation of surface plasmonic optical fibre sensors is fabricated using multiple coatings deposited on a lapped section of a single mode fibre. Post-deposition UV laser irradiation using a phase mask produces a nano-scaled surface relief grating structure, resembling nano-wires. The overall length of the individual corrugations is approximately 14 μm with an average full width half maximum of 100 nm. Evidence is presented to show that these surface structures result from material compaction created by the silicon dioxide and germanium layers in the multi-layered coating and the surface topology is capable of supporting localised surface plasmons. The coating compaction induces a strain gradient into the D-shaped optical fibre that generates an asymmetric periodic refractive index profile which enhances the coupling of the light from the core of the fibre to plasmons on the surface of the coating. Experimental data are presented that show changes in spectral characteristics after UV processing and that the performance of the sensors increases from that of their pre-UV irradiation state. The enhanced performance is illustrated with regards to change in external refractive index and demonstrates high spectral sensitivities in gaseous and aqueous index regimes ranging up to 4000 nm/RIU for wavelength and 800 dB/RIU for intensity. The devices generate surface plasmons over a very large wavelength range, (visible to 2 μm) depending on the polarization state of the illuminating light. © 2013 SPIE.

Socio-economic vision graph generation and handover in distributed smart camera networks

In this article we present an approach to object tracking handover in a network of smart cameras, based on self-interested autonomous agents, which exchange responsibility for tracking objects in a market mechanism, in order to maximise their own utility. A novel ant-colony inspired mechanism is used to learn the vision graph, that is, the camera neighbourhood relations, during runtime, which may then be used to optimise communication between cameras. The key benefits of our completely decentralised approach are on the one hand generating the vision graph online, enabling efficient deployment in unknown scenarios and camera network topologies, and on the other hand relying only on local information, increasing the robustness of the system. Since our market-based approach does not rely on a priori topology information, the need for any multicamera calibration can be avoided. We have evaluated our approach both in a simulation study and in network of real distributed smart cameras.

Permanent magnet synchronous generator based wind power generation system fault protection schemes

The PMSG-based wind power generation system protection is presented in this paper. For large-scale systems, a voltagesource converter rectifier is included. Protection circuits for this topology are studied with simulation results for cable permanent fault conditions. These electrical protection methods are all in terms of dumping redundant energy resulting from disrupted path of power delivery. Pitch control of large-scale wind turbines are considered for effectively reducing rotor shaft overspeed. Detailed analysis and calculation of damping power and resistances are presented. Simulation results including fault overcurrent, DC-link overvoltage and wind turbine overspeed are shown to illustrate the system responses under different protection schemes to compare their application and effectiveness.