Reliability of timber bridges using nailed plywood box beams

The Nailed Box Beam structural efficiency is directly dependent of the flange-web joint behavior, which determines the partial composition of the section, as the displacement between elements reduces the effective rigidity of the section and changes the stress distribution and the total displacement of the section. This work discusses the use of Nailed Plywood Box Beams in small span timber bridges, focusing on the reliability of the beam element. It is presented the results of tests carried out in 21 full scale Nailed Plywood Box Beams. The analysis of maximum load tests results shows that it presents a normal distribution, permitting the characteristic values calculation as the normal distribution theory specifies. The reliability of those elements was analyzed focusing on a timber bridge design, to estimate the failure probability in function of the load level.

Timber bridges : design, construction, inspection, and maintenance /

Mode of access: Internet.

The builder's complete assistant, or, A library of arts and sciences, absolutely necessary to be understood by builders and workmen in general : viz. I. Arithmetick, vulgar and decimal, in whole numbers and fractions. II. Geometry, lineal, superficial, and solid. III. Architecture, universal. IV. Mensuration. V. Plain trigonometry. VI. Surveying of land, &c. VII. Mechanick powers. VIII. Hydrostaticks : illustrated by above thirteen hundred examples of lines, superficies, solids, mouldings, pedestals, columns, pilasters, entablatures, pediments, imposts, block cornices, rustick quoins, frontispieces, arcades, porticos, &c. : proportioned by modules and minutes, according to Andrea Palladio, and by equal parts : likewise great varieties of trussed roofs, timber bridges, centerings, arches, groins, twisted rails, compartments, obelisks, vases, pedestals for bustos, sun-dials, fonts, &c. and methods for raising heavy bodies by the force of levers, pulleys, axes in peritrochio, screws, and wedges, as also water, by the common pump, crane, etc. : wherein the properties, and pressure of the air on water, &c. are explained : the whole exemplified by 77 large quarto copper-plates /

All of the numbered plates in the atlas are double plates, and thus are counted twice in the adjusted plate count.

Field Evaluation of Timber Preservation Treatments for Highway Applications Final Report, December 2007

Timber material repair and replacement cost for timber bridges is a considerable expense to highway agencies in Iowa, especially to county road departments. To address these needs, the objectives of this investigation was to study the field effectiveness of various treatment alternatives used on Iowa roadway projects and to determine if the current specifications and testing are adequate for providing proper wood preservation. To satisfy the research needs, the project scope involved a literature review, identification of metrics, questionnaire survey of Iowa counties, onsite inspections, and a review of current specifications and testing procedures. Based on the preservative information obtained, the following general conclusions were made: Copper naphthenate is recommended as the plant-applied preservative treatment for timber bridges. Best Management Practices should be followed to ensure quality treatment of timber materials. Bridge maintenance programs need to be developed and implemented. The Iowa Department of Transportation specifications for preservative treatment are the regulating specification for bridges constructed with state or federal funding in Iowa and are also recommended for all other bridges.

Field Testing and Evaluation of a Demonstration Timber Bridge, February 2012

Asphalt wearing surfaces are commonly used on timber bridges with transverse glued-laminated deck panel systems to help protect the timber components. However, poor performance of these asphalt wearing surfaces in the past has resulted in repeated repair and increased maintenance costs. This report describes the field demonstration and testing of a newly-constructed, glued-laminated timber girder bridge. Previous field work revealed that differential panel deflections in the glued-laminated deck were one significant factor resulting in the premature failure of the asphalt wearing surfaces on these bridges. In addition, laboratory work subsequent to the field testing attempted to address the problematic asphalt cracking common in transverse glued-laminated panel decks by testing several deck joint connection alternatives. The field demonstration project described in this report showcases the retrofit detail that was determined to provide the best field performance. The project was a cooperative effort between the Bridge Engineering Center (BEC) at Iowa State University and the United States Department of Agriculture (USDA) Forest Service Forest Products Laboratory (FPL).

Heavy Agricultural Loads on Pavements and Bridges, HR-1073, 1999

During the harvest season in Iowa, it is common to have single axle loads on secondary roads and bridges that are excessive (typical examples are grain carts) and well beyond normal load limits. Even though these excessive loads occur only during a short time of the year, they may do significant damage to pavements and bridges. In addition, the safety of some bridges may be compromised because of the excessive loads, and sometimes there may be little indication to the users that damage may be imminent. At this time there are no Iowa laws regulating axle loads allowed for agricultural equipment. This study looks at the potential problems this may cause on secondary roads and timber stringer bridges. Both highway pavement and timber bridges are evaluated in this report. A section (panel) of Iowa PCC paved county road was chosen to study the effects of heavy agricultural loads on pavements. Instrumentation was applied to the panel and a heavily loaded grain cart was rolled across. The collected data were analyzed for any indication of excessive stresses of the concrete. The second study, concerning excessive loads on timber stringer bridges, was conducted in the laboratory. Four bridge sections were constructed and tested. Two of the sections contained five stringers and two sections had three stringers. Timber for the bridges came from a dismantled bridge, and deck panels were cut from new stock. All timber was treated with creosote. A hydraulic load was applied at the deck mid-span using a foot print representing a tire from a typical grain cart. Force was applied until failure of the system resulted. The collected data were evaluated to provide indications of load distribution and for comparison with expected wheel loads for a typical heavily loaded single axle grain cart. Results of the pavement tests showed that the potential of over-stressing the pavement is a possibility. Even though most of the tension stress levels recorded were below the rupture strength of the concrete, there were a few instances where the indicated tension stress level exceeded the concrete rupture strength. Results of the bridge tests showed that when the static ultimate load capacity of the timber stringer bridge sections was reached, there was sudden loss of capacity. Prior to reaching this ultimate capacity, the load sharing between the stringers was very uniform. The failure was characterized by loss of flexural capacity of the stringers. In all tests, the ultimate test load exceeded the wheel load that would be applied by an 875 bushel single axle grain cart.

Evaluation of Bridge Replacement Alternatives for the County Bridge System, HR-365 August 1994

Recent reports have indicated that 23.5 percent of the nation's highway bridges are structurally deficient and 17.7 percent are functionally obsolete. A significant number of these bridges are on the Iowa county road system. The objective of the investigation described in this report was to identify, review and evaluate replacement bridges currently being used by various counties in Iowa and surrounding states. Iowa county engineers, county engineers in neighboring states as well as private manufacturers of bridge components, and regional precad prestressed concrete manufacturers were contacted to determine the most common replacement bridge types being used. Depending upon the findings of the review, possible improvements and/or new replacement bridge systems were to be proposed. A questionnaire was developed and sent to county engineers in Iowa and several counties in surrounding states. The results of the questionnaire showed that the most common replacement bridges in Iowa are the continuous concrete slab and prestressed concrete bridges. The primary reason these types are used is because of the availability of standard designs and because of their ease of maintenance. Counties seldom construct these types of bridges using their own labor forces, but instead contract the work. However, county forces are used to construct steel stringer, precast reinforced concrete and timber bridges. In general, 69 percent of the counties indicate an ability and willingness to use their own forces to design and construct relatively short span bridges (i.e., 40 A or less) provided the construction procedures are relatively simple. Several unique replacement bridge types used in Iowa that are constructed by county forces are documented and presented in this report. Sufficient details are provided to allow county engineers to determine if some of these bridges could be used to resolve some of their own replacement bridge problems. Where possible, cost information has also been provided. Each of these bridge types were evaluated for various criteria (e.g., cost effectiveness, conformance to AASI-ITO standards, range of sizes, etc.) by a panel of four Iowa county engineers; a summary of this critique is included. After evaluating the questionnaire responses from the counties and evaluating the various bridge replacement concepts currently in use, one new bridge replacement concept and one modification of a current Iowa county bridge replacement concept were developed. Both of these concepts would utilize county labor forces.

Pontes de madeira para pequenos vãos para situações emergenciais

In Brazil there are many cases of cities that suffer from flooding. It often destroys much of the structure of the city, and isolates many families. Relying on emergency measures for these cases and similar cases is of utmost importance. This paper proposes the development of a project of a timber bridge that can be used in emergency situations such as occurs in situations of floods and especially on side roads. It is considered one type of structural bridge which has, among other characteristics, an easy transportation and assembly of the elements. The development is carried out, at this early stage of the project, only about the verification and sizing of structural elements of the superstructure of the bridge. For this purpose, it relies on computer programs, and fundamentally on PCFrame Visual Taco. The first allows you to model the structure and determine the efforts of calculating the elements, and the second one assists at the scaling and the verifications in accordance with the Brazilian technical standards for timber bridges. The wood used in the project comes from the tree Eucalyptus saligna, which is easy to acquaint and manipulate and comes from the region Vale do Paraíba. The bridge in this case of application should have the characteristics mentioned below: short execution time, simplicity of structure and an assembly of a relatively low cost

Passarela estaiada com tabuleiro de madeira laminada protendida em módulos curvos

É inegável a importância do desenvolvimento de tecnologias de uso racional da madeira e de solução de problemas de transportes em nossas cidades, principalmente por causa do processo crescente de urbanização do mundo. Existe também, a necessidade estética de se unir à alta tecnologia, o belo. As passarelas estaiadas com tabuleiro de madeira laminada protendida, em módulos curvos, atendem a todas estas exigências. A construção de um protótipo permitiu que a realização de ensaios estáticos e dinâmicos, cujos resultados evidenciaram a viabilidade técnica e econômica de passarelas estaiadas usando madeira de reflorestamento, de tabuleiros compostos apenas por placas de madeira laminada protendida e da construção de placas curvas de madeira laminada protendida. Também foi possível comprovar que as vibrações induzidas por pedestres são a condição mais crítica de projeto. A investigação da perda de curvatura do tabuleiro demonstrou o sucesso do projeto, embora mais estudos ao longo do tempo sejam necessários. Baseando-se nos resultados experimentais, realizou-se a calibração do modelo numérico, que permitiu realizar simulações para determinar quais variáveis definem a resposta da passarela construída. Sugestões de procedimentos de elaboração e construção de passarelas, assim como de criação de norma brasileira específica para pontes e passarelas de madeira, são apresentadas.

Pontes protendidas de Eucalipto citriodora

O conceito de pontes de madeira em tabuleiro laminado protendido surgiu na década de 70, no Canadá, como forma de reabilitação para tabuleiros laminados pregados. Diversas pesquisas foram desenvolvidas para verificar o desempenho estrutural e a durabilidade do sistema, e estes estudos comprovaram a eficácia do método. Devido ao enorme déficit de pequenas e médias pontes em todo o seu território, o Brasil tem buscado cada vez mais materiais e tecnologias alternativas economicamente competitivas para sua construção. Partindo de pesquisas desenvolvidas em outros países, desde 1993 começaram a ser desenvolvidas pesquisas nacionais para verificar a viabilidade em se utilizar madeiras brasileiras para construção de pontes, e a resposta, mais uma vez, foi positiva. Este trabalho tem como objetivos o estudo teórico e experimental das pontes de eucalipto protendidas transversalmente, através do projeto e construção da primeira ponte protendida de madeira da América do Sul. Por meio de provas de carga, foi avaliado o desempenho da ponte e a influência dos guarda-rodas e defensas na rigidez do tabuleiro. Os resultados mostram que o sistema protendido de eucalipto é uma ótima alternativa para o Brasil.

Chart of bill of timber in bridges, culverts, cattle-guard and roadways, signed by S.D. Woodruff

Chart of bill of timber in bridges, culverts, cattle-guard and roadways, signed by S.D. Woodruff, Oct. 18, 1855.

The theory, practice, and architecture of bridges of stone, iron, timber, and wire;

Mode of access: Internet.

Manual for Evaluation, Rehabilitation and Strengthening of Low Volume Bridges, HR-323, 1993

This report contains an evaluation and design manual for strengthening and replacing low volume steel stringer and timber stringer bridges. An advisory panel consisting of county and municipal engineers provided direction for the development of the manual. NBI bridge data, along with results from questionnaires sent to county and municipal engineers were used to formulate the manual. Types of structures shown to have the greatest need for cost-effective strengthening methods are steel stringer and timber stringer bridges. Procedures for strengthening these two types of structures have been developed. Various types of replacement bridges have also been included so that the most cost effective solution for a deficient bridge may be obtained. The key results of this study is an extensive compilation, which can be used by county engineers, of the most effective techniques for strengthening deficient existing bridges. The replacement bridge types included have been used in numerous low volume applications in surrounding states, as well as in Iowa. An economic analysis for determining the cost-effectiveness of the various strengthening methods and replacement bridges is also an important part of the manual. Microcomputer spreadsheet software for several of the strengthening methods, types of replacement bridges and for the economic analysis has been developed, documented and presented in the manual. So the manual, Chp. 3 of the final report, can be easily located, blue divider pages have been inserted to delineate the manual from the rest of the report.

Design of Piles for Integral Abutment Bridges, HR-252, 1984

More and more, integral abutment bridges are being used in place of the more traditional bridge designs with expansion releases. In this study, states which use integral abutment bridges were surveyed to determine their current practice in the design of these structures. To study piles in integral abutment bridges, a finite element program for the soil-pile system was developed (1) with materially and geometrically nonlinear, two and three dimensional beam elements and (2) with a nonlinear, Winkler soil model with vertical, horizontal, and pile tip springs. The model was verified by comparison to several analytical and experimental examples. A simplified design model for analyzing piles in integral abutment bridges is also presented. This model grew from previous analytical models and observations of pile behavior. The design model correctly describes the essential behavioral characteristics of the pile and conservatively predicts the vertical load-carrying capacity. Analytical examples are presented to illustrate the effects of lateral displacements on the ultimate load capacity of a pile. These examples include friction and end-bearing piles; steel, concrete, and timber piles; and bending about the weak, strong, and 45° axes for H piles. The effects of cyclic loading are shown for skewed and nonskewed bridges. The results show that the capacity of friction piles is not significantly affected by lateral displacements, but the capacity of end-bearing piles is reduced. Further results show that the longitudinal expansion of the bridge can introduce a vertical preload on the pile.

Demonstration Project using Railroad Flatcars for Low-Volume Road Bridges, TR-444, 2003

The use of Railroad Flatcars (RRFCs) as the superstructure on low-volume county bridges has been investigated in a research project conducted by the Bridge Engineering Center at Iowa State University. These bridges enable county engineers to replace old, inadequate county bridge superstructures for less than half the cost and in a shorter construction time than required for a conventional bridge. To illustrate their constructability, adequacy, and economy, two RRFC demonstration bridges were designed, constructed, and tested: one in Buchanan County and the other in Winnebago County. The Buchanan County Bridge was constructed as a single span with 56-ft-long flatcars supported at their ends by new, concrete abutments. The use of concrete in the substructure allowed for an integral abutment at one end of the bridge with an expansion joint at the other end. Reinforced concrete beams (serving as longitudinal connections between the three adjacent flatcars) were installed to distribute live loads among the RRFCs. Guardrails and an asphalt milling driving surface completed the bridge. The Winnebago County Bridge was constructed using 89-ft-long flatcars. Preliminary calculations determined that they were not adequate to span 89 ft as a simple span. Therefore, the flatcars were supported by new, steel-capped piers and abutments at the RRFCs' bolsters and ends, resulting in a 66-ft main span and two 10-ft end spans. Due to the RRFC geometry, the longitudinal connections between adjacent RRFCs were inadequate to support significant loads; therefore, transverse, recycled timber planks were utilized to effectively distribute live loads to all three RRFCs. A gravel driving surface was placed on top of the timber planks, and a guardrail system was installed to complete the bridge. Bridge behavior predicted by grillage models for each bridge was validated by strain and deflection data from field tests; it was found that the engineered RRFC bridges have live load stresses significantly below the AASHTO Bridge Design Specification limits. To assist in future RRFC bridge projects, RRFC selection criteria were established for visual inspection and selection of structurally adequate RRFCs. In addition, design recommendations have been developed to simplify live load distribution calculations for the design of the bridges. Based on the results of this research, it has been determined that through proper RRFC selection, construction, and engineering, RRFC bridges are a viable, economic replacement system for low-volume road bridges.