Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms

Ethanol oxidation on platinum stepped surfaces vicinal to the (111) pole modified by tin has been studied to determine the role of this adatom in the oxidation mechanism. Tin has been slowly deposited so that the initial stages of the deposition take place on the step, and deposition on the terrace only occurs when the step has been completely decorated. Voltammetric and chronoamperometric experiments demonstrate that tin on the step catalyzes the oxidation. The maximum enhancement is found when the step is completely decorated by tin. FTIR experiments using normal and isotopically labeled ethanol have been used to elucidate the effect of the tin adatoms in the mechanism. The obtained results indicate that the role of tin is double: (i) when the surface has sites capable of breaking the C-C bond of the molecule, that is, when the step sites are not completely covered by tin, it promotes the oxidation of CO formed from the molecular fragments to CO(2) through a bifunctional mechanism and (ii) it catalyzes the oxidation of ethanol to acetic acid.

Sequence-specific electrochemical detection of Alicyclobacillus acidoterrestris DNA using electroconductive polymer-modified fluorine tin oxide electrodes

This study outlines the quantification of low levels of Alicyclobacillus acidoterrestris in pure cultures, since this bacterium is not inactivated by pasteurization and may remain in industrialized foods and beverages. Electroconductive polymer-modified fluorine tin oxide (FTO) electrodes and multiple nanoparticle labels were used for biosensing. The detection of A. acidoterrestris in pure cultures was performed by reverse transcription polymerase chain reaction (RT-PCR) and the sensitivity was further increased by asymmetric nested RT-PCR using electrochemical detection for quantification of the amplicon. The quantification of nested RT-PCR products by Ag/Au-based electrochemical detection was able to detect 2 colony forming units per mL (CFU mL(-1)) of spores in pure culture and low detection and quantification limits (7.07 and 23.6 nM, respectively) were obtained for the target A. acidoterrestris on the electrochemical detection bioassay.

Residual stresses in TiN, DLC and MoS(2) coated surfaces with regard to their tribological fracture behaviour

Thin hard coatings on components and tools are used increasingly due to the rapid development in deposition techniques, tribological performance and application skills. The residual stresses in a coated surface are crucial for its tribological performance. Compressive residual stresses in PVD deposited TiN and DLC coatings were measured to be in the range of 0.03-4 GPa on steel substrate and 0.1-1.3 GPa on silicon. MoS(2) coatings had tensional stresses in the range of 0.8-1.3 on steel and 0.16 GPa compressive stresses on silicon. The fracture pattern of coatings deposited on steel substrate were analysed both in bend testing and scratch testing. A micro-scale finite element method (FEM) modelling and stress simulation of a 2 mu m TiN-coated steel surface was carried out and showed a reduction of the generated tensile buckling stresses in front of the sliding tip when compressive residual stresses of 1 GPa were included in the model. However, this reduction is not similarly observed in the scratch groove behind the tip, possibly due to sliding contact-induced stress relaxation. Scratch and bending tests allowed calculation of the fracture toughness of the three coated surfaces, based on both empirical crack pattern observations and FEM stress calculation, which resulted in highest values for TiN coating followed by MoS(2) and DLC coatings, being K(C) = 4-11, about 2, and 1-2 MPa M(1/2), respectively. Higher compressive residual stresses in the coating and higher elastic modulus of the coating correlated to increased fracture toughness of the coated surface. (C) 2009 Elsevier B.V. All rights reserved.

Effect of cerium (IV) ions on the anticorrosion properties of siloxane-poly(methyl methacrylate) based film applied on tin coated steel

This work investigates the influence of the addition of cerium (IV) ions on the anticorrosion properties of organic-inorganic hybrid coatings applied to passivated tin coated steel. In order to evaluate the specific effect of cerium (IV) addition on nanostructural features of the organic and inorganic phases of the hybrid coating, the hydrolytic polycondensation of silicon alkoxide and the radical polymerization of the methyl methacrylate (MMA) function were induced separately. The corrosion resistance of the coatings was evaluated by means of linear polarization, Tafel type curves and electrochemical impedance measurements. The impedance results obtained for the hybrid coatings were discussed based on an electrical equivalent circuit used to fit the experimental data. The electrochemical results clearly showed the improvement of the protective properties of the organic-inorganic hybrid coating mainly when the cerium (IV) was added to the organic phase solution precursor, which seemed to be due to the formation of a more uniform and densely reticulated siloxane-PMMA film. (C) 2010 Elsevier Ltd. All rights reserved.

Low-frequency noise and static analysis of the impact of the TiN metal gate thicknesses on n- and p-channel MuGFETs

The impact of the titanium nitride (TIN) gate electrode thickness has been investigated in n and p channel SOI multiple gate field effect transistors (MuGFETs) through low frequency noise charge pumping and static measurements as well as capacitance-voltage curves The results suggest that a thicker TIN metal gate electrode gives rise to a higher EOT a lower mobility and a higher interface trap density The devices have also been studied for different back gate biases where the GIFBE onset occurs at lower front-gate voltage for thinner TIN metal gate thickness and at higher V(GF) In addition it is demonstrated that post deposition nitridation of the MOCVD HfSiO gate dielectric exhibits an unexpected trend with TIN gate electrode thickness where a continuous variation of EOT and an increase on the degradation of the interface quality are observed (C) 2010 Elsevier Ltd All rights reserved

Influence of the sidewall crystal orientation, HfSiO nitridation and TiN metal gate thickness on n-MuGFETs under analog operation

This work characterizes the analog performance of SOI n-MuGFETs with HfSiO gate dielectric and TiN metal gate with respect to the influence of the high-k post-nitridation. TiN thickness and device rotation. A thinner TiN metal gate is found favorable for improved analog characteristics showing an increase in intrinsic voltage gain. The devices where the high-k material is subjected to a nitridation step indicated a degradation of the Early voltage (V(EA)) values which resulted in a lower voltage gain. The 45 degrees rotated devices have a smaller V(EA) than the standard ones when a HfSiO dielectric is used. However, the higher transconductance of these devices, due to the increased mobility in the (1 0 0) sidewall orientation, compensates this V(EA) degradation of the voltage gain, keeping it nearly equal to the voltage gain values of the standard devices. (C) 2011 Elsevier Ltd. All rights reserved.

Activity of platinum-tin catalysts prepared by the Pechini-Adams method for the electrooxidation of ethanol

Pt-Sn electrocatalysts of different compositions were prepared and dispersed on carbon Vulcan XC-72 using the Pechini-Adams method. The catalysts were characterized by energy dispersive X-ray analysis and X-ray diffraction. The electrochemical properties of these electrode materials were also examined by cyclic voltammetry and chronoamperometric experiments in acid medium. The results showed that the presence of Sn greatly enhances the activity of Pt towards the electrooxidation of ethanol. Moreover, it contributes to reduce the amount of noble metal in the anode of direct alcohol fuel cells, which remains one of the challenges to make the technology of direct alcohol fuel cells possible. Electrolysis of ethanol solutions at 0.55 V vs. RHE allowed to determine by liquid chromatography acetaldehyde and acetic acid as the main reaction products. CO(2) was also analyzed after trapping it in a NaOH solution indicating that the cleavage of the C-C bond in the ethanol molecule did occur during the adsorption process. In situ IR reflectance spectroscopy helped to investigate in more details the reaction mechanism through the identification of the reaction products as well as the presence of some intermediate adsorbed species, such as linearly bonded carbon monoxide. (C) 2009 Elsevier B.V. All rights reserved.

Study of Annealed Indium Tin Oxide-Films prepared by RF Reactive Magnetron Sputtering

Tin doped indium oxide (ITO) films were deposited on glass substrates by rf reactive magnetron sputtering using a metallic alloy target (In-Sn, 90-10). The post-deposition annealing has been done for ITO films in air and the effect of annealing temperature on the electrical, optical and structural properties of ITO films was studied. It has been found that the increase of the annealing temperature will improve the film electrical properties. The resistivity of as deposited film is about 1.3 x 10(-1) Omega*cm and decreases down to 6.9 x 10(-3) Omega*cm as the annealing temperature is increased up to 500 degrees C. In addition, the annealing will also increase the film surface roughness which can improve the efficiency of amorphous silicon solar cells by increasing the amount of light trapping.

Assessment of the potential of tin sulphide thin films prepared by sulphurization of metallic precursors as cell absorbers

In this work, SnxSy thin films have been grown on soda-lime glass substrates by sulphurization of metallic precursors in a nitrogen plus sulphur vapour atmosphere. Different sulphurization temperatures were tested, ranging from 300 °C to 520 °C. The resulting phases were structurally investigated by X-Ray Diffraction and Raman spectroscopy. Composition was studied using Energy Dispersive Spectroscopy being then correlated with the sulphurization temperature. Optical measurements were performed to obtain transmittance and reflectance spectra, from which the energy band gaps, were estimated. The values obtained were 1.17 eV for the indirect transition and for the direct transition the values varied from 1.26 eV to 1.57 eV. Electrical characterization using Hot Point Probe showed that all samples were p-type semiconductors. Solar cells were built using the structure: SLG/Mo/SnxSy/CdS/ZnO:Ga and the best result for solar cell efficiency was 0.17%.

Revestimento de superfícies metálicas com TiN e AIN produzidos com plasma magnetrão

Este trabalho visa a obtenção e o estudo das características dos revestimentos de AlN e TiN em substratos metálicos, produzidos por pulverização catódica em plasma magnetrão, num equipamento com cátodo oco, desenvolvido no LEF do CEFITEC. Este equipamento foi adaptado para o presente trabalho, através de alguns elementos adicionais, designadamente de um porta-amostras que permitiu o revestimento de provetes em lotes. Deste estudo conclui-se que a aplicação de uma tensão de “bias” na amostra altera a morfologia dos revestimentos e as características dos materiais que constituem o filme, não só no que diz respeito à sua composição, como também proporciona estruturas mais densas e com menos porosidade. As tensões de “bias” típicas foram de –100 V no caso de AlN e de –75 V e com uma potência de 2,0 kW no cátodo no caso de TiN. Neste último foi considerado apenas o objectivo da obtenção da fase d, de estrutura CFC (cor dourada), por ser a única de interesse industrial. Por difracção de raios x verificou-se a obtenção de TiN e TiN0,9 com as características pretendidas. Também se verificou que as tensões residuais dos filmes são de compressão e isotrópicas.

Effectiveness of house dust mite acaricide tri-n-butyl tin maleate on carpets, fabrics and mattress foam: a standardization of methodology

The aim of this study was to determine the effectiveness of the acaricide tri-n-butyl tin maleate, industrially applied to samples of carpets, mattress foam, and fabrics used for furniture upholstery, soft toys and shoe uppers. Approximately 100 adult house dust mites of the species Dermatophagoides pteronyssinus were inoculated into a Petri dish containing the sample (a piece of carpet, mattress foam, or fabric), treated with the acaricide, randomly collected. Mite-maintenance culture medium was added on top of each sample. After one, two, three, seven and 30 days of incubation at 25 ºC and 75% relative humidity, each dish was examined using a 40X stereoscopic microscope (40X). One hundred percent acaricide effectiveness was obtained in treated materials by the end of the 30th-day postinoculation period, under optimal conditions for mite maintenance.

Activity of Tri-N-Butyl Tin maleate in carpets against Staphylococcus aureus and Aspergillus niger, verified through two methodologies: Inhibition Halo (HZ) and Inhibition Surface (Print)

The aim of the present study was to verify the activity of the Tri-N-Butyl Tin maleate compound against Staphylococcus aureus and Aspergillus niger, after its industrial application in 40 samples of carpets of different materials (polypropylene, polyester, polyamide and wool). The qualitative assays were performed through two methodologies: Inhibition Halo (HZ) and Inhibition of Surface (Print). The carpet with the product inhibited 100% of bacterial (Staphylococcus aureus) and fungi (Aspergillus niger) growth, under the conditions of this study. The microbial inhibition was higher in upper portion of carpets. The methodologies employed appear to be adequate to test the bactericide and fungicide activities of the Tri-N-Butyl Tin maleate. The print methodology confirmed the results obtained by the inhibition zone assay. Further studies using the same methodologies are needed to confirm our results.

Traduzir Teatro no Estado Novo: Gata em Telhado de Zinco Quente (1959), tradução de Sérgio Guimarães, do original Cat on a Hot Tin Roof (1955), de Tennessee Williams

À luz da viragem cultural dos Estudos de Tradução ocorrida nos anos 80 e tendo em conta a interdisciplinaridade abordada nos campos literário, cultural e histórico pela Manipulation School (Lefevere, Bassnett, Lambert, Hermans e Toury), na esteira de Itamar Even-Zohar com a Teoria dos Polissistemas (1979), a presente dissertação pretende analisar a tradução portuguesa da peça Cat on a Hot Tin Roof (1955), da autoria de Tennessee Williams, intitulada Gata em Telhado de Zinco Quente (1959), de Sérgio Guimarães. Este pode ser um caso representativo de como a tradução para teatro actua na cultura receptora numa perspectiva diatópica, antevendo a dimensão intercultural da tradução para o palco. É ao tradutor que cabe a tarefa de transferir a peça de um sistema linguístico e cultural para outro, conhecendo, se possível, o grau de representabilidade da mesma e o contexto cultural de chegada. Deste modo, é evidenciada a competência artístico-criativa do tradutor teatral que trabalha com o intuito de manter, fidus interpres, as intenções do autor da obra original. No período em que Cat on a Hot Tin Roof foi escrita, ensombrado pelo controlo sociopolítico do Macartismo nos E.U.A. e o contexto em que a tradução foi concretizada, sob a vigência da Ditadura de Salazar, a (auto)censura desempenha um papel fundamental ao moldar a produção literária nos dois sistemas culturais. Numa época em que, mais do que nos dias de hoje, traduzir consistia numa actividade subserviente e secundária, Vasco Morgado, detentor do monopólio de teatros em Lisboa encomendou a Sérgio Guimarães a tradução de uma peça de Tennessee Williams. Com base na teoria desenvolvida por Lawrence Venuti em The Translator’s Invisibility (1995), não é despiciente problematizar, neste estudo de caso, a invisibilidade do tradutor/mediador entre o texto e a representação, abordando simultaneamente as estratégias então necessárias para a peça ser aprovada e posta em cena.

Ag-TiNx electrodes deposited on piezoelectric poly(vinylidene fluoride) for biomedical sensor applications

Electroactive polymers are one of the most interesting class of polymers used as smart materials in various applications, such as the development of sensors and actuators for biomedical applications in areas such as smart prosthesis, implantable biosensors and biomechanical signal monitoring, among others. For acquiring or applying the electrical signal from/to the piezoelectric material, suitable electrodes can be produced from Ti based coatings with tailored multifunctional properties, conductivity and antibacterial characteristics, through Ag inclusions. This work reports on Ag-TiNx electrodes, deposited by d. c. and pulsed magnetron sputtering at room temperature on poly(vinylidene fluoride), PVDF, the all-round best piezoelectric polymer.. Composition of the electrodes was assessed by microanalysis X-ray system (EDS - energy dispersive spectrometer). The XRD results revealed that the deposition conditions preserve the polymer structure and suggested the presence of crystalline fcc-TiN phase and fcc-Ag phase in samples with N2 flow above 3 sccm. According to the results obtained from SEM analysis, the coatings are homogeneous and Ag clusters were found for samples with nitrogen flow above 3 sccm. With increasing nitrogen flow, the sheet resistivity tend to be lower than the samples without nitrogen, leading also to a decrease of the piezoelectric response. It is concluded that the deposition conditions do significantly affect the piezoelectric polymer, which maintain its characteristics for sensor/actuator applications.