Studies on thermal-oxidative degradation behaviours of raw natural rubber: PRI and thermogravimetry analysis

Thermal-oxidative degradation behaviours of raw natural rubber (NR) have been investigated by using thermogravimetry analysis in inert and oxidative atmospheres and the plasticity retention index (PRI). The activation energy E a, was calculated using Horowitz-Metzger and Coats-Redfern methods and compared with PRI. The E a values obtained by each method were in good agreement with each other. The June samples are the least stable rubbers among the studied ones, whereas February samples exhibited the highest values of activation energy, therefore in agreement with the PRI behaviour, which indicates that the thermo-oxidative stability of the June samples are the poorest during the thermo-oxidative degradation reaction. Natural rubber is a product of biological origin, and thus these variations in the values of thermal behaviour and PRI might be related to the genetic differences and alterations of climatic conditions that act directly on the synthesis of non-rubber constituents, which are generally reflected in latex and rubber properties. © 2013 Institute of Materials, Minerals and Mining.

Characterisation of lignins isolated from sugarcane bagasse pretreated with acidified ethylene glycol and ionic liquids

Sugarcane bagasse pretreatment processes using acidified aqueous ethylene glycol (EG) and ionic liquids (ILs) have been reported recently. In this study, recovery of lignins from these processes was conducted, as well as determination of their physico-chemical properties. The amount of lignins recovered from 1-butyl-3-methylimidazolium chloride ([bmim]Cl) with HCl as a catalyst and [bmim][CH3SO3] was ∼42%, and ∼35%–36% by EG with HCl or H2SO4 as a catalyst, respectively. The isolated lignins were characterised using wet chemistry, spectroscopy and thermogravimetry analysis (TGA), and the results compared to soda lignin from NaOH pretreatment of bagasse. The IL and EG lignins contained no or trace amounts of carbohydrates, slightly lower hydrogen content but slightly higher oxygen contents than soda lignin. The IL and EG lignins contained more C-3 and C-5 reactive sites for Mannich reaction and had more p-hydroxypheny propane unit structures than soda lignin. Two-dimensional heteronuclear single quantum coherence (2D HSQC) nuclear magnetic resonance (NMR) identified the major substructural units in the lignins, and allowed differences among them to be studied. As EG lignins were extracted in very reactive environment, intermediate enol ethers were formed and led to cleavage reactions which were not apparent in the other lignins. 31P NMR and infra-red spectroscopy results showed that IL and EG lignins had lower total hydroxyl content than soda lignin, probably indicating that a higher degree of self-polymerisation occurred during bagasse pretreatment, despite the use of lower temperature and shorter reaction time. On the basis of the salient features of these lignins, potential applications were proposed.

Preparation temperature effect on the synthesis of various carbon nanostructures

Various carbon nanostructures (CNs) have been prepared by a simple deposition technique based on the pyrolysis of a new carbon source material tetrahydrofuran (THF) mixed with ferrocene using quartz tube reactor in the temperature range 700-1100 degrees C. A detailed study of how the synthesis parameter such as growth temperature affects the morphology of the carbon nanostructures is presented. The obtained CNs are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), electron dispersive scattering (EDS)thermogravimetry analysis (TGA), Raman and transmission electron microscope (TEM). It is observed that at 700 degrees C. normal CNTs are formed. Iron filled multi-walled carbon nanotubes (MWCNTs) and carbon nanoribbons (CNRs) are formed at 950 degrees C. Magnetic characterization of iron filled MWCNTs and CNRs studied at 300 K by superconducting quantum interference device (SQUID) reveals that these nanostructures have an enhanced coercivity (Hc = 1049 Oe) higher than that of bulk Fe. The large shape anisotropy of MWCNTs, which act on the encapsulated material (Fe), is attributed for the contribution of the higher coercivity. Coiled carbon nanotubes (CCNTs) were obtained as main products in large quantities at temperature 1100 degrees C.

Pd-coated Ni nanoparticles by the polyol method: an efficient hydrogenation catalyst

Pd-coated Ni nanoparticles of 50 +/- 15 nm size are prepared by the polyol method and characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and thermogravimetry analysis. Surface coverage of Pd on Ni particles is less than a monolayer for 0.5 and 1 at% Pd-coated Ni. Quantitative conversion of nitrobenzene to aniline is observed over these Pd-coated Ni particles at 27degreesC under one atmospheric pressure of hydrogen. 0.5 and 1 at% Pd-coated Ni exhibits 10 times greater activity than that of typical colloidal palladium and platinum catalysts and 2.5 times higher activity than commercial 5 wt% Pd/C.

Preparação e avaliação de hidrogéis nanocompósitos à base de alginato na remoção de Cu (II) e Zn (II) de soluções aquosas

Esta dissertação teve como objetivo, a preparação de hidrogéis à base de alginato contendo argila e material magnético em sua estrutura. Foram analisadas as modificações nas características físico-químicas dos hidrogéis preparados com diferentes reticulantes (CaCl2 e FeCl3) e diferentes concentrações de material magnético (1 e 3 % m/m) e argila (1, 5 e 10 %). Após isso, os hidrogéis foram avaliados quanto à capacidade de remoção de íons Cu2+ e Zn2+ de soluções aquosas. As amostras foram caracterizadas quanto à composição química por espectroscopia na região do infravermelho (FTIR), quanto à morfologia por microscopia óptica e microscopia eletrônica de varredura (SEM) e quanto às propriedades magnéticas por magnetometria de amostra vibrante (VSM). Através da técnica de difratometria de raios-X (XRD), foi possível verificar a natureza do material magnético e a dispersão da argila nos hidrogéis. A estabilidade térmica das amostras foi analisada por análise termogravimétrica (TGA). Os resultados mostraram que tanto a argila como o material magnético ficaram bem dispersos nas amostras. De forma geral, foram preparados hidrogéis com morfologia esférica, sendo que os hidrogéis de alginato de cálcio tenderam a apresentar maior resistência térmica do que os hidrogéis de alginato de ferro. Todas as amostras magnéticas apresentaram comportamento superparamagnético, porém as amostras de alginato de ferro mostraram-se quebradiças após o intumescimento em água. O tempo médio de equilíbrio de intumescimento foi de 240 minutos. Os resultados de cinética de adsorção mostraram que os hidrogéis de alginato de cálcio preparados nas condições avaliadas nesta Dissertação foram eficientes na remoção dos íons Cu2+ e Zn2+, sendo que o cobre apresentou maior afinidade pelo hidrogel do que o zinco

Síntese e avaliação de hidrogéis à base de alginato e nanopartículas magnéticas preparadas in situ para remoção de Mn(II) e Ni(II) de efluente industrial

Esta Dissertação teve como objetivo,a síntese de hidrogéis à base de alginato e nanopartículas magnéticas (maghemita) preparadas in situ. Os hidrogéis foram preparados em diferentes concentrações de alginato de sódio (2 e 3% m/v), FeSO4 (0,3 e 0,5 mol L-1) e CaCl2 (0,1 e 0,3 mol L-1). As propriedades físico-químicas dos hidrogéis foram analisadas e, posteriormente, foram avaliados quanto à capacidade de remoção de íons Ni2+ e Mn2+ de soluções aquosas. Para caracterização das amostras foram utilizadas diversas técnicas de análises, tais como, análise granulométrica, microscopia óptica (OM), microscopia eletrônica de varredura (SEM), microscopia eletrônica de transmissão (TEM), magnetometria de amostra vibrante (VSM), espectroscopia na região do infravermelho por transformada de Fourier (FTIR), difratometria de raios-X (XRD), espectroscopia Mössbauer, e análise termogravimétrica (TGA). Foram preparados hidrogéis com morfologia predominantemente esférica e dimensões micrométricas (500 a 850 m), com átomos de Fe e Ca dispersos uniformemente em sua estrutura. Os hidrogéis apresentaram boa resistência térmica e comportamento superparamagnético. As amostras foram intumescidas em água deionizada durante um intervalo de tempo a fim de avaliar o grau de intumescimento (Q) para determinar a amostra com a melhor resposta para posterior aplicação em solução aquosa contendo íons metálicos (Ni2+ e Mn2+). Os resultados revelaram que a amostra cuja concentração de 3% m/v de alginato de sódio, 0,3 mol L-1 de FeSO4 e 0,3 mol L-1 de CaCl2 obteve maior Q (50%). Em consequência deste resultado, optou-se por utilizar estaamostra, na remoção de metais pesados presentes em soluções aquosas e em efluentes industriais. Vários parâmetros,tais como: tempo de contato,pH, concentração inicial do íon e massa de hidrogel foram estudados.Os resultados, para efluente sintético, revelaram que o tempo de equilíbrio foi de 60 minutos; a capacidade de remoção dos metais melhora com o aumento de pH (3 a 9), sendo máxima em pH 7;quanto menor a concentração inicial da solução iônica (50 a 500 mg L-1), maior a capacidade de remoção, 52% de Ni2+ e 49% de Mn2+ (concentração inicial de 50 mg L-1). No efluente industrial, a remoção foi de 61% de Ni2+ e 57% de Mn2+(300 mg de hidrogel). Os resultados encontrados revelaram que os hidrogéis magnéticos produzidos à base de alginato têm potencial uso no tratamento de efluentes industriais contaminados com metais pesados

印刷线路板废弃物的热解与动力学实验研究

分别应用管式炉反应器和热重分析手段对印刷线路板废弃物的热解行为和热解动力学进行了实验研究。在管式炉中，研究不同的热解温度：700～950℃，对产物分布和气体成分分布的影响。实验结果表明：PCB热解气体的主要成分是H2和CO2，气体的热值较低，仅为2.09～5.41MJ/m^3，PCB不适合以气体产物为目标的能源利用方式。应用Friedman方法对PCB的热解动力学进行了研究，求得PCB的热解动力学参数分别是：表观活化能190.92kJ/mol，反应级数5.97，指前因子lnA47.14min^-1。

Thermal stability, crystallization, structure and morphology of syndiotactic 1,2-polybutadiene/organoclay nanocomposite

Syndiotactic 1,2-polybutadiene/organoclay nanocomposites were prepared and characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), polarized optical microscopy (POM), and differential scanning calorimetry (DSC), respectively. The XRD shows that exfoliated nanocomposites are formed dominantly at lower clay concentrations (less than 2%), at higher clay contents intercalated nanocomposites dominate. At the same time, the XRD indicates that the crystal structures of sPB formed in the sPB/organoclay nanocomposites do not vary, only the relative intensity of the peaks corresponding to (0 1 0) and (2 0 0)/(1 1 0) crystal planes, respectively, varies. The DSC and POM indicate that organoclay layers can improve cooling crystallization temperature, crystallization rate and reducing the spherulite sizes of sPB. TGA shows that under argon flow the nanocomposites exhibit slight decrease of thermal stability, while under oxygen flow the resistance of oxidation and thermal stability of sPB/organoclay nanocomposites were significantly improved relative to pristine sPB. The primary and secondary crystallization for pristine sPB and sPB/organoclay (2%) nanocomposites were analyzed and compared based on different approaches.

Preparation of polymer/silica nanoscale hybrids through sol-gel method involving emulsion polymers (PMMA/SiO2)

The different poly (methyl methacrylate) (PMMA) /SiO2 hybrids were prepared through sol-gel method involving PMMA emulsion (emulsion method) and PMMA/THF solution (solution method). The samples were characterized by differential scanning calorimetry(DSC), thermogravimetry analysis(TGA), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that PMMA/SiO2 composites in nanoscale were prepared by emulsion method, and its size of phase heterogeneity was less than that of solution method. Meanwhile, the polymer emulsion as the reactive medium was more suitable for the formation of SiO2 network.

Synthesis and characterization of (phenolphthalein/4,4 '-thiodiphenol) PES copolymers

Copolymers based on monomers phenolphthalein (PP)/4,4'-thiodiphenol (Bis-T)/4,4'-dichlorodiphenylsulfone (DCDPS) were prepared by a route involving the toluene, N-methyl-2-pyrrolidone and anhydrous potassium carbonate synthesis. The range of optimum reaction temperature was between 185 and 195 degrees C. The copolymers were characterized by C-13 NMR, differential scanning calorimetry (DSC) and torsion braid analysis. It was found that all of the copolymers were random and homogeneous and their glass transition temperatures (T-g) decreased linearly with an increase of Bis-T contents in the copolymers. The thermal stability determined by thermogravimetry analysis in air atmosphere indicated that the copolymer had better resistance to thermo-oxidative degradation. Dynamic mechanical measurement showed that (PP/Bis-T) PES copolymers containing 0-50 mol% of Bis-T components had two secondary relaxations. (C) 1998 Elsevier Science Ltd. All rights reserved.

Effects of gamma radiation on the photoluminescence properties of polycarbonate matrices doped with terbium complex

Luminescent films containing terbium complex [Tb(acac)(3)(H(2)O)(3)] (acac = acetylacetonate) doped into a polycarbonate (PC) matrix were prepared and irradiated at low-dose gamma radiation with ratio of 5 and 10 kGy. The PC polymer was doped with 5% (w/w) of the Tb(3+) complex. The thermal behavior was investigated by utilization of differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). Changes in thermal stability due to the addition of doping agent into the polycarbonate matrix. Based on the emission spectra of PC:5% Tb(acac)(3) film were observed the characteristic bands arising from the (5)D(4) -> (7)F(J) transitions of Tb(3+) ion (J = 0-6), indicating the ability to obtain the luminescent films. Doped samples irradiated at low dose of gamma irradiation showed a decrease in luminescence intensity with increasing of the dose. (C) 2009 Elsevier Ltd. All rights reserved.

Dependence of the electrical conductivity and elastomeric properties on sample preparation of blends of polyaniline and natural rubber

Blend films (free-standing) containing 20% in volume of polyaniline (PANI) in 80% of natural rubber (NR) were fabricated by casting in three different ways: (1) adding PANI-EB (emeraldine base) dissolved in N-methyl-2-pyrrolidone (NMP) to the latex (NRL), (2) adding PANI-EB dissolved in in-cresol to NR dissolved in xylol (NRD), (3) overlaying the surface of a pure NR cast film with a PANI layer grown by in situ polymerization (NRO). All the films were immersed into HCl solution to achieve the primary doping (protonation) of PANI before the characterization. The main goal here was to investigate the elastomeric and electrical conductivity properties for each blend, which may be applied as pressure and deformation sensors in the future. The characterization was carried out by optical microscopy, dc conductivity, vibrational spectroscopy (infrared absorption and Raman scattering), thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile stress-strain curves. The results suggest that the NRL blend is the most suitable in terms of mechanical and electrical properties required for applications in pressure and deformation sensors: a gain of conductivity without losing the elastomeric property of the rubber. (c) 2005 Wiley Periodicals, Inc.

Caracterização mecânica e térmica da borracha natural formulada e vulcanizada dos clones: GT 1, IAN 873, PB 235 e RRIM 600

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Matrizes poliméricas puras e modificadas para adsorção do gás sulfeto de hidrogênio

The underground natural gas found associated or not with oil is characterized by a mixture of hydrocarbons and residual components such as carbon dioxide (CO2), nitrogen gas (N2) and hydrogen sulfide (H2S), called contaminants. The H2S especially promotes itself as a contaminant of natural gas to be associated with corrosion of pipelines, to human toxicity and final applications of Natural Gas (NG). The sulfur present in the GN must be fully or partially removed in order to meet the market specifications, security, transport or further processing. There are distinct and varied methods of desulfurization of natural gas processing units used in Natural Gas (UPGN). In order to solve these problems have for example the caustic washing, absorption, the use of membranes and adsorption processes is costly and great expenditure of energy. Arises on such findings, the need for research to active processes of economic feasibility and efficiency. This work promoted the study of the adsorption of sulfide gas in polymer matrices hydrogen pure and modified. The substrates of Poly(vinyl chloride) (PVC), poly(methyl methacrylate) (PMMA) and sodium alginate (NaALG) were coated with vanadyl phosphate compounds (VOPO4.2H2O), vanadium pentoxide (V2O5), rhodamine B (C28H31N2O3Cl) and ions Co2+ and Cu2+, aiming to the adsorption of hydrogen sulfide gas (H2S). The adsorption tests were through a continuous flow of H2S in a column system (fixed bed reactor) adsorption on a laboratory scale. The techniques used to characterize the adsorbents were Infrared spectroscopy (FTIR), thermogravimetry analysis (TGA), X-ray fluorescence (XRF), the X-ray diffraction (XRD) electron microscopy (SEM). Such work indicates, the results obtained, the adsorbents modified PMMA, PVC and NaALG have a significant adsorptive capacity. The matrix that stood out and had the best adsorption capacity, was to ALG modified Co2+ with a score of 12.79 mg H2S / g matrix

Calcium polyphosphate coacervates: effects of thermal treatment

The addition of calcium chloride eletrolyte to sodium polyphosphate solutions lead to Calcium polyphosphate coacervates. The effects of a thermal treatment were investigated with the objective to increase the relative stability of the obtained material. Thermogravimetry analysis indicates that coacervates became less hydrophilic and more thermally stable after the thermal treatment. Crystallization was identified through differential scanning calorimetry and X-ray diffraction. Morphological changes were observed after the thermal treatment by scanning electron microscopy. N-2 adsorption-desorption isotherms suggest that both materials, thermally treated or not, display type IV isotherms, low superficial area and mesoporous structure. Stability experiments in solutions at different pH values show that the thermally treated calcium polyphosphate is relatively more stable than the non-treated coacervate.