Thermoelectricity abstracts

Mode of access: Internet.

Experimental high frequency apparatus: how to make and use it,

Mode of access: Internet.

Apparatus and method for heat-run test on high-power PWM converters with low energy expenditure

Before installation, a voltage source converter is usually subjected to heat-run test to verify its thermal design and performance under load. For heat-run test, the converter needs to be operated at rated voltage and rated current for a substantial length of time. Hence, such tests consume huge amount of energy in case of high-power converters. Also, the capacities of the source and loads available in the research and development (R&D) centre or the production facility could be inadequate to conduct such tests. This paper proposes a method to conduct heat-run tests on high-power, pulse width modulated (PWM) converters with low energy consumption. The experimental set-up consists of the converter under test and another converter (of similar or higher rating), both connected in parallel on the ac side and open on the dc side. Vector-control or synchronous reference frame control is employed to control the converters such that one draws certain amount of reactive power and the other supplies the same; only the system losses are drawn from the mains. The performance of the controller is validated through simulation and experiments. Experimental results, pertaining to heat-run tests on a high-power PWM converter, are presented at power levels of 25 kVA to 150 kVA.

Thermoelectric Cooling and Power Generation

In a typical thermoelectric device, a junction is formed from two different conducting materials, one containing positive charge carriers (holes) and the other negative charge carriers (electrons). When an electric current is passed in the appropriate direction through the junction, both types of charge carriers move away from the junction and convey heat away, thus cooling the junction. Similarly, a heat source at the junction causes carriers to flow away from the junction, making an electrical generator. Such devices have the advantage of containing no moving parts, but low efficiencies have limited their use to specialty applications, such as cooling laser diodes. The principles of thermoelectric devices are reviewed and strategies for increasing the efficiency of novel materials are explored. Improved materials would not only help to cool advanced electronics but could also provide energy benefits in refrigeration and when using waste heat to generate electrical power.

Design and implementation of the embedded capacitance layers for decoupling of wireless sensor nodes

In this paper, the embedded capacitance material (ECM) is fabricated between the power and ground layers of the wireless sensor nodes, forming an integrated capacitance to replace the large amount of decoupling capacitors on the board. The ECM material, whose dielectric constant is 16, has the same size of the wireless sensor nodes of 3cm*3cm, with a thickness of only 14μm. Though the capacitance of a single ECM layer being only around 8nF, there are two reasons the ECM layers can still replace the high frequency decoupling capacitors (100nF in our case) on the board. The first reason is: the parasitic inductance of the ECM layer is much lower than the surface mount capacitors'. A smaller capacitance value of the ECM layer could achieve the same resonant frequency of the surface mount decoupling capacitors. Simulation and measurement fit this assumption well. The second reason is: more than one layer of ECM material are utilized during the design step to get a parallel connection of the several ECM capacitance layers, finally leading to a larger value of the capacitance and smaller value of parasitic. Characterization of the ECM is carried out by the LCR meter. To evaluate the behaviors of the ECM layer, time and frequency domain measurements are performed on the power-bus decoupling of the wireless sensor nodes. Comparison with the measurements of bare PCB board and decoupling capacitors solution are provided to show the improvement of the ECM layer. Measurements show that the implementation of the ECM layer can not only save the space of the surface mount decoupling capacitors, but also provide better power-bus decoupling to the nodes.

New Ways of Looking at the State Apparatus and the State Archive in Nineteenth Century Ireland: Curiosities from that Phonetic Museum - Royal Irish Constabulary Reports and their Political Uses, 1879-91

This essay seeks to contextualise the intelligence work of the Royal Irish Constabulary, particularly in the 1880s, in terms of the wider British and imperial practice and, as a corollary, to reflect upon aspects of the structure of the state apparatus and the state archive in Ireland since the Union. The author contrasts Irish and British police and bureaucratic work and suggests parallels between Ireland and other imperial locations, especially India. This paper also defines the narrowly political, indeed partisan, uses to which this intelligence was put, particularly during the Special Commission of 1888 on 'Parnellism and crime', when governmentheld police records were made available to counsel for The Times. By reflecting on the structure of the state apparatus and its use in this instance, the author aims to further the debate on the governance of nineteenth-century Ireland and to explore issues of colonial identity and practice. The line of argument proposed in this essay is prefigured in Margaret O'Callaghan, British high politics and a nationalist Ireland: criminality, land and the law under Forster and Balfour (Cork, 199