Structural and textural studies of NiO impregnation in mesoporous ZrO2-CeO2 for catalysis applications.

The synthesis of zirconia-based ordered mesoporous structures for catalytic applications is a research area under development. These systems are also potential candidates as anodes in intermediate temperature solid oxide fuel cells (it-SOFC) due to an enhancement on their surface area [1-4]. The structural features of mesoporous zirconia-ceria materials in combination with oxygen storage/release capacity (OSC) are crucial for various catalytic reactions. The direct use of hydrocarbons as fuel for the SOFC (instead of pure H2), without the necessity of reforming and purification reactors can improve global efficiency of these systems [4]. The X-ray diffraction data showed that ZrO2-x%CeO2 samples with x>50 are formed by a larger fraction of the cubic phase (spatial group Fm3m), while for x<50 the major crystalline structure is the tetragonal phase (spatial group P42/nmc). The crystallite size of the cubic phase increases with increase in ceria content. The tetragonal crystallite size decreases when ceria content increases. After impregnation, the Rietveld analysis showed a NiO content around 60wt.% for all samples. The lattice parameters for the ZrO2 tetragonal phase are lower for higher ZrO2 contents, while for all samples the cubic NiO and CeO2 parameters do not present changes. The calculated densities are higher for higher ceria content, as expected. The crystallite size of NiO are similar (~20nm) for all samples and 55nm for the NiO standard. Nitrogen adsorption experiments revealed a broader particle size distribution for higher CeO2 content. The superficial area values were around 35m2/g for all samples, the average pore diameter and pore volumes were higher when increasing ceria content. After NiO impregnation the particle size distribution was the same for all samples, with two pore sizes, the first around 3nm and a broader peak around 10nm. The superficial area increased to approximately 45m2/g for all samples, and the pore volume was also higher after impregnation and increased when ceria content increased. These results point up that the impregnation of NiO improves the textural characteristics of the pristine material. The complementary TEM/EDS images present a homogeneous coating of NiO particles over the ZrO2-x%CeO2 support, showing that these samples are excellent for catalysis applications. [1] D. Y. Zhao, J. Feng, Q. Huo, N. Melosh, G. H. Fredrickson, B. F. Chmelka, G. D. Stucky, Science 279, 548-552 (1998). [2] C. Yu, Y. Yu, D. Zhao, Chem. Comm. 575-576 (2000). [3] A. Trovarelli, M. Boaro, E. Rocchini, C. de Leitenburg, G. Dolcetti, J. Alloys Compd. 323-324 (2001) 584-591. [4] S. Larrondo, M. A. Vidal, B. Irigoyen, A. F. Craievich, D. G. Lamas, I. O. Fábregas, et al. Catal. Today 107–108 (2005) 53-59.

Genetic studies of Cu-Pb-Zn mineralisation in Triassic red beds of Western Europe

Continental red bed sequences are host, on a worldwide scale, to a characteristic style of mineralisation which is dominated by copper, lead, zinc, uranium and vanadium. This study examines the features of sediment-hosted ore deposits in the Permo-Triassic basins of Western Europe, with particular reference to the Cu-Pb-Zn-Ba mineralisation in the Cheshire Basin, northwest England, the Pb-Ba-F deposits of the Inner Moray Firth Basin, northeast Scotland, and the Pb-rich deposits of the Eifel and Oberpfalz regions, West Germany. The deposits occur primarily but not exclusively in fluvial and aeolian sandstones on the margins of deep, avolcanic sedimentary basins containing red beds, evaporites and occasionally hydrocarbons. The host sediments range in age from Permian to Rhaetian and often contain (or can be inferred to have originally contained) organic matter. Textural studies have shown that early diagenetic quartz overgrowths precede the main episode of sulphide deposition. Fluid inclusion and sulphur isotope data have significantly constrained the genetic hypotheses for the mineralisation and a model involving the expulsion of diagenetic fluids and basinal brines up the faulted margins of sedimentary basins is favoured. Consideration of the development of these sedimentary basins suggests that ore emplacement occurred during the tectonic stage of basin evolution or during basin inversion in the Tertiary. ð34S values for barite in the Cheshire Basin range from 13.8% to 19.3% and support the theory that the Upper Triassic evaporites were the principal sulphur source for the mineralisation and provided the means by which mineralising fluids became saline. In contrast, δ34S values for barite in the Inner Moray Firth Basin (mean δ34S = + 29%) are not consistent with simple derivation of sulphur from the evaporite horizons in the basin and it is likely that sulphur-rich Jurassic shales supplied the sulphur for the mineralisation at Elgin. Possible sources of sulphur for the mineralisation in West Germany include hydrothermal vein sulphides in the underlying Devonian sediments and evaporites in the overlying Muschelkalk. Textural studies of the deeply buried sandstones in the Cheshire Basin reveal widespread dissolution and replacement of detrital phases and support the theory that red bed diagenetic processes are responsible for the release of metals into pore fluids. The ore solutions are envisaged as being warm (60-150%C), saline (9-22 wt % equiv NaCl) fluids in which metals were transported as chloride complexes. The distribution of δ34S values for sulphides in the Cheshire Basin (-1.8% to + 16%), the Moray Firth Basin (-4.8% to + 27%) and the German Permo-Triassic Basins (-22.2% to -12.2%) preclude a magmatic source for the sulphides and support the contention that sulphide precipitation is thought to result principally from sulphate reduction processes, although a decrease in temperature of the ore fluid or reaction with carbonates may also be important. Methane is invoked as the principal reducing agent in the Cheshire Basin, whilst terrestrial organic debris and bacterial reduction processes are thought to have played a major part in the genesis of the German ore deposits.

Melt topology and chemistry during partial melting in contact aureoles : an experimental study and field example

This study was initiated to investigate partial melting within the high-grade metamorphic rocks beneath the Little Cottonwood contact aureole (Utah, USA), in order to understand the melt generation, melt migration, and geometry of initial melt distribution on grain scale during crustal anatexis. The emplacement of the Little Cottonwood stock produced a contact aureole in the pelitic host rocks of the Big Cottonwood formation (BC). Metamorphic isogrades in pelitic rocks range form biotite to 2nd sillimanite grade as a function of distance from the contact. Migmatites are restricted to the highest grade and resulted form partial melting of the BC formation rocks. First melt was produced by a combined muscovite/biotite dehydration reaction in the sillimanite + k-feldspar stability field. Melt extraction from the pelites resulted in restites (magnetite + cordierite + alumosilicate ± biotite) surrounded by feldspar enriched quartzite zones. This texture is the result of gradual infiltration of partial melts into the quartzite. Larger, discrete melt accumulation occurred in extensional or transpressional domains such as boudin necks, veins, and ductile shear zones. Melt composition are Si02- rich, crystallized as pegmatites, and apparently were very mobile. They were able to infiltrate the quartzite pervaisivly. These melts are similar in composition to first melts produced in the hydrothermal partial melt experiments at 2kbar between 700 - 800°C on fine grained high metamorphic rocks (andalusite-cordierited-biotite-zone) of the BC formation. The experimental melts are water rich and in disequilibrium with the melting rock. Initial melt composition is heterogeneous for short run duration, reflective a lack of chemical equilibrium between individual melt pools. Rock core scale heterogeneity decreased with time indicating partial homogenization of melt compositions. A simultaneous shift of melt composition to higher silica content with time was observed. The silica content of the melt increased due to local melt/mineral reactions. Melt textures indicate that reactive melt transport is most efficient along grain boundaries rimmed by dissimilar grains. Melt heterogeneity resulted in chemical potential gradients which are major driving forces for initial melt migration and govern melt distribution during initial melting. An additional subject of the thesis is the crystal size distributions of opaque minerals in a fine-grained, high-grade meta-pelite of the Big Cottonwood which were obtained from 3D X-ray tomography (uCT) and 2D thin section analysis. µCT delivers accurate size distributions within a restricted range (~ a factor of 20 in size in a single 3D image), while the absolute number of crystals is difficult to obtain from these sparsely distributed, small crystals on the basis of 2D images. Crystal size distributions obtained from both methods are otherwise similar. - Ce travail de recherche a été entrepris dans le but d'étudier les processus de fusion partielle dans les roches fortement métamorphiques de l'auréole de contact de Little Cottonwood (Utah, USA) et ceci afin de comprendre la génération de liquide de fusion, la migration de ces liquides et la géométrie de la distribution initiale des liquides de fusion à l'échelle du grain durant l'anatexie de la croûte. L'emplacement du petit massif intrusif de Little Cottonwood a produit une auréole de contact dans les roches pélitiques encaissantes appartenant à la Foimation du Big Cottonwood (BC). Les isogrades métamorphiques dans les roches pélitiques varient de l'isograde de la biotite à la deuxième isograde de la sillimanite en fonction de la distance par rapport au massif intrusif. Les migmatites sont restreintes aux zones montrant le plus haut degré métamorphique et résultent de la fusion partielle des roches de la Formation de BC. Le premier liquide de fusion a été produit par la réaction de déshydratation combinée de la muscovite et de la biotite dans le champ de stabilité du feldspath potassique Pt de la sillimanite. L'extraction du liquide de fusion des pélites forme des restites (magnétites + cordiérite + aluminosilicate ± biotite) entourées par des zones de quartzites enrichies en feldspath. Cette texture est le résultat de l'infiltration graduelle du liquide de fusion partielle dans les quartzites. Des accumulations distinctes et plus larges de liquide de fusion ont lieu dans des domaines d'extension ou de transpression tels que les boudins, les veines, et les zones de cisaillement ductile. La composition des liquides de fusion est similaire à celle des liquides pegmatoïdes, et ces liquides sont apparemment très mobiles et capables d'infiltrer les quartzites. Ces liquides de fusion ont la même composition que les premiers liquides produits dans les expériences hydrotheunales de fusion partielle à 2kbar et entre 700-800° C sur les roches finement grenues et hautement métamorphiques (andalousite-cordiérite-biotite zone) de la Formation de BC. Les liquides de fusion obtenus expérimentalement sont riches en eau et sont en déséquilibre avec la roche en fusion. La composition initiale des liquides de fusion est hétérogène pour les expériences de courte durée et reflète l'absence d'équilibre chimique entre les différentes zones d'accumulation des liquides de fusion. L'hétérogénéité à l'échelle du noyau s'estompe avec le temps et témoigne de l'homogénéisation de la composition des liquides de fusion. Par ailleurs, on observe parallèlement un décalage de la composition des liquides vers des compositions plus riches en silice au cours du temps. Le contenu en silice des liquides de fusion évolue vers un liquide pegmatitique en raison des réactions liquides/minéraux. Les textures des liquides de fusion indiquent que le transport des liquides est plus efficace le long des bordures de grains bordés par des grains différents. Aucun changement apparent du volume total n'est visible. L'hétérogénéité des liquides s'accompagne d'un gradient de potentiel chimique qui sert de moteur principal à la migration des liquides et à la distribution des liquides durant la fusion. Un sujet complémentaire de ce travail de thèse réside dans l'étude de la distribution de la taille des cristaux opaques dans les pélites finement grenues et fortement métamorphiques de la Formation de Big Cottonwood. Les distributions de taille ont été obtenues suite à l'analyse d'images 3D acquise par tomographie ainsi que par analyse de lames minces. La microtomographie par rayon X fournit une distribution de taille précise sur une marge restreinte (- un facteur de taille 20 dans une seule image 3D), alors que le nombre absolu de cristaux est difficile à obtenir sur la base d'image 2D en raison de la petite taille et de la faible abondance de ces cristaux. Les distributions de taille obtenues par les deux méthodes sont sinon similaire. Abstact: Chemical differentiation of the primitive Earth was due to melting and separation of melts. Today, melt generation and emplacement is still the dominant process for the growth of the crust. Most granite formation is due to partial melting of the lower crust, followed by transport of magma through the crust to the shallow crust where it is emplaced. Partial melting and melt segregation are essential steps before such a granitic magma can ascent through the crust. The chemistry and physics of partial melting and segregation is complex. Hence detailed studies, in which field observations yield critical information that can be compared to experimental observations, are crucial to the understanding of these fundamental processes that lead and are leading to the chemical stratification of the Earth. The research presented in this thesis is a combined field and experimental study of partial melting of high-grade meta-pelitic rocks of the Little Cottonwood contact aureole (Utah, USA). Contact metamorphic rocks are ideal for textural studies of melt generation, since the relatively short times of the metamorphic event prevents much of the recrystallization which plagues textural studies of lower crustal rocks. The purpose of the study is to characterize melt generation, identify melting reactions, and to constrain melt formation, segregation and migration mechanisms. In parallel an experimental study was undertaken to investigate melt in the high grade meta pelitic rocks, to confirm melt composition, and to compare textures of the partial molten rock cores in the absence of deformation. Results show that a pegmatoidal melt is produced by partial melting of the pelitic rocks. This melt is highly mobile. It is capable of pervasive infiltration of the adjacent quartzite. Infiltration results in rounded quartz grains bordered by a thin feldspar rim. Using computed micro X-ray tomography these melt networks can be imaged. The infiltrated melt leads to rheological weakening and to a decompaction of the solid quartzite. Such decompaction can explain the recent discovery of abundant xenocrysts in many magmas, since it favors the isolation of mineral grains. Pervasive infiltration is apparently strongly influenced by melt viscosity and melt-crystal wetting behavior, both of which depend on the water content of melt and the temperature. In all experiments the first melt is produced on grain boundaries, dominantly by the local minerals. Grain scale heterogeneity of a melting rock leads thus to chemical concentration gradients in the melt, which are the driving force for initial melt migration. Pervasive melt films along grain boundaries leading to an interconnected network are immediately established. The initial chemical heterogeneities in the melt diminish with time. Résumé large public: La différenciation chimique de la Terre primitive est la conséquence de la fusion des roches et de la séparation des liquides qui en résultent. Aujourd'hui, la production de liquide magmatique est toujours le mécanisme dominant pour la croissance de la croûte terrestre. Ainsi la formation de la plupart des granites est un processus qui implique la production de magma par fusion partielle de la croûte inférieure, la migration de ces magmas à travers la croûte et finalement son emplacement dans les niveaux superficielle de la croûte terrestre. Au cours de cette évolution, les processus de fusion partielle et de ségrégation sont des étapes indispensables à l'ascension des granites à travers la croûte. Les conditions physico-chimiques nécessaires à la fusion partielle et à l'extraction de ces liquides sont complexes. C'est pourquoi des études détaillées des processus de fusion partielle sont cruciales pour la compréhension de ces mécanismes fondamentaux responsables de la stratification chimique de la Terre. Parmi ces études, les observations de terrain apportent notamment des informations déterminantes qui peuvent être comparées aux données expérimentales. Le travail de recherche présenté dans ce mémoire de thèse associe études de terrain et données expérimentales sur la fusion partielle des roches pélitiques de haut degré métamorphiques provenant de l'auréole de contact de Little Cottonwood (Utah, USA). Les roches du métamorphisme de contact sont idéales pour l'étude de la folination de liquide de fusion. En effet, la durée relativement courte de ce type d'événement métamorphique prévient en grande partie la recristallisation qui perturbe les études de texture des roches dans la croûte inférieure. Le but de cette étude est de caractériser la génération des liquides de fusion, d'identifier les réactions responsables de la fusion de ces roches et de contraindre la formation de ces liquides et leur mécanisme de ségrégation et de migration. Parallèlement, des travaux expérimentaux ont été entrepris pour reproduire la fusion partielle de ces roches en laboratoire. Cette étude a été effectuée dans le but de confirmer la composition chimique des liquides, et de comparer les textures obtenues en l'absence de déformation. Les résultats montrent qu'un liquide de fusion pegmatoïde est produit par fusion partielle des roches pélitiques. La grande mobilité de ce liquide permet une infiltration pénétrative dans les quarzites. Ces infiltrations se manifestent par des grains de quartz arrondis entourés par une fine bordure de feldspath. L'utilisation de la tomography à rayons X a permis d'obtenir des images de ce réseau de liquide de fusion. L'infiltration de liquide de fusion entraîne un affaiblissement de la rhéologie de la roche ainsi qu'une décompaction des quartzites massifs. Une telle décompaction peut expliquer la découverte récente d'abondants xénocristaux dans beaucoup de magmas, puisque elle favorise l'isolation des minéraux. L'infiltration pénétrative est apparemment fortement influencée par la viscosité du fluide de fusion et le comportement de la tension superficielle entre les cristaux et le liquide, les deux étant dépendant du contenu en eau dans le liquide de fusion et de la température. Dans toutes les expériences, le premier liquide est produit sur les bordures de grains, principalement par les minéraux locaux. L'hétérogénéité à l'échelle des grains d'une roche en fusion conduit donc à un gradient de concentration chimique dans le liquide, qui sert de moteur à l'initiation de la migration du liquide. Des fines couches de liquide de fusion le long de bordures de grains formant un réseau enchevêtré s'établit immédiatement. Les hétérogénéités chimiques initiales dans le liquide s'estompent avec le temps.

Geology and Geochronology of Silica Sands of Coastal Plain of Thiruvananthapuram District, Kerala,India,With Special reference to Late Quaternary Environment

Department of Marine Geology & Geophysics, Cochin University of Science & Technology

Activity and characterization by XPS, HR-TEM, Raman spectroscopy, and BET surface area of CuO/CeO2-TiO2 catalysts

Structural and textural studies of a CuO/TiO2 System modified by cerium oxide were conducted using Raman spectroscopy, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and N-2 absorption (BET specific surface area). The introduction of a minor amount of CeO2 (Ce0.09Ti0.82O1.91CU0.09 sample) resulted in a material with the maximum surface area value. The results of Raman spectroscopy revealed the presence of only two crystalline phases, TiO2 anatase and CeO2 cerianite, with well-dispersed copper species. TEM micrographs showed a trend toward smaller TiO2 crystallites when the cerium oxide content was increased. The XPS analysis indicated the rise of a second peak in Ti 2p spectra with the increasing amount of CeO2 located at higher binding energies than that due to the Till in a tetragonal symmetry. The CuO/TiO2 system modified by CeO2 displayed a superior performance for methanol dehydrogenation than the copper catalyst supported only on TiO2 or CeO2.

Metamorphic and geochronogical study of the Triassic El Oro metamorphic complex, Ecuador: Implications for high-temperature metamorphism in a forearc zone

In the forearc of the Andean active margin in southwest Ecuador, the El Oro metamorphic complex exhibits a well exposed tilted forearc section partially migmatized. We used Raman spectroscopy on carbonaceous matter (RSCM) thermometry and pseudosections coupled with mineralogical and textural studies to constrain the pressure–temperature (P–T) evolution of the El Oro metamorphic complex during Triassic times. Our results show that anatexis of the continental crust occurred by white-mica and biotite dehydration melting along a 10 km thick crustal domain (from 4.5 to 8 kbar) with increasing temperature from 650 to 700 °C. In the biotite dehydration melting zone, temperature was buffered at 750–820 °C in a 5 km thick layer. The estimated average thermal gradient during peak metamorphism is of 30 °C/km within the migmatitic domain can be partitioned into two apparent gradients parts. The upper part from surface to 7 km depth records a 40–45 °C/km gradient. The lower part records a quasi-adiabatic geotherm with a 10 °C/km gradient consistent with an isothermal melting zone. Migmatites U–Th–Pb geochronology yielded zircon and monazite ages of 229.3 ± 2.1 Ma and 224.5 ± 2.3 Ma, respectively. This thermal event generated S-type magmatism (the Marcabeli granitoid) and was immediately followed by underplating of the high-pressure low-temperature (HP-LT) Arenillas–Panupalí unit at 225.8 ± 1.8 Ma. The association of high-temperature low-pressure (HT-LP) migmatites with HP-LT unit constitutes a new example of a paired metamorphic belt along the South American margin. We propose that in addition to crustal thinning, underplating of the Piedras gabbroic unit before 230 Ma provided the heat source necessary to foster crustal anatexis. Furthermore, its MORB signature shows that the asthenosphere was involved as the source of the heat anomaly. S-type felsic magmatism is widespread during this time and suggests that a large-scale thermal anomaly affected a large part of the South American margin during the late Triassic. We propose that crustal anatexis is related to an anomaly that arose during subduction of the Panthalassa ocean under the South American margin. Slab verticalization or slab break-off can be invoked as the origin of the upwelling of the asthenosphere.

Granulometry of surface sediments from the Panama Basin (Table 2, 3)

Panama Basin sediment surface coarse fractions are dominantly composed of planktonic foraminiferal remains. Textural studies of these coarse fractions by means of a large diameter settling tube system reveal characteristics grain size spectra with important modes at 2.0-2.25 phi, 2.3-2.45 phi, 2.5-2.75 phi, 3.0-33 phi, and 3.4-3.75 phi. The coarser modes consist of large Globoquadrina dutertrei and Globorotalia menardii shells, the finer ones of small planktonic foraminiferal species and of shell fragments of the larger species. Analyses of samples from the Carnegie Gap provide sufficient information such that the extent of the high energy environment close to the sill depth can be mapped; the textural analyses also seem to indicate south and northward flowing components of the bottom currents which transport particle assemblages with distinct textural characteristics. The samples bear evidence for large scale removal of calcareous fines from the crest of structural highs; the fines are then dumped on the flanks of these elevations.

Textural and microstructural studies of zinc sulfide and associated phases in certain base metal deposits

A textural and microstructural study of a variety of zinc sulfide-containing ores has been undertaken, and the possible depositional and deformational controls of textural and microstructural development considered. Samples for the study were taken from both deformed and undeformed zinc ores of the Central U.S. Appalachians, and deformed zinc ores of the English Pennines. A variety of mineralogical techniques were employed, including transmitted and reflected light microscopy of etched and unetched material, transmission electron microscopy and electron microprobe analysis. For the Pennine zinc sulfides, spectroscopic, x-ray diffraction and fluid inclusion studies were also undertaken. Optical and electron optical examination of the Appalachian material confirmed the suitability of zinc sulfide for detailed study with such techniques. Growth and deformation-related microstructures could be distinguished from specimen-preparation induced artifacts. A deformationally-mduced lamelliform optical anisotropy is seen to be developed in areas hosting a dense planar microstructure of {111} twin- and slip-planes. The Pennine zinc sulfide texturally records a changing depositional environment. Thus, for example, delicately growth- zoned crystals are truncated and cross-cut by solution disconformities. Fluid inclusion studies indicate a highly saline (20-25 wt. % equiv. NaCl), low temperature (100-150°C.) fluid. Texturally, two varieties of zinc sulfide can be recognised; a widely developed, iron- banded variety, and a paragenetically early variety, banded due to horizons rich in crystal defects and microscopic inclusions. The zinc sulfide takes the form of a disordered 3C-polytype, with much of the disorder being deformational in origin. Twin- and slip-plane fabrics are developed . A deformation-related optical anisotropy is seen to overprint growth-related anisotropy, along with cuprian alteration of certain {111} deformation planes.

Textural classification of land cover using support vector machines: an empirical comparison with parametric, non parametric and hybrid classifiers in the Bolivian Amazon

Land cover classification is a key research field in remote sensing and land change science as thematic maps derived from remotely sensed data have become the basis for analyzing many socio-ecological issues. However, land cover classification remains a difficult task and it is especially challenging in heterogeneous tropical landscapes where nonetheless such maps are of great importance. The present study aims to establish an efficient classification approach to accurately map all broad land cover classes in a large, heterogeneous tropical area of Bolivia, as a basis for further studies (e.g., land cover-land use change). Specifically, we compare the performance of parametric (maximum likelihood), non-parametric (k-nearest neighbour and four different support vector machines - SVM), and hybrid classifiers, using both hard and soft (fuzzy) accuracy assessments. In addition, we test whether the inclusion of a textural index (homogeneity) in the classifications improves their performance. We classified Landsat imagery for two dates corresponding to dry and wet seasons and found that non-parametric, and particularly SVM classifiers, outperformed both parametric and hybrid classifiers. We also found that the use of the homogeneity index along with reflectance bands significantly increased the overall accuracy of all the classifications, but particularly of SVM algorithms. We observed that improvements in producer’s and user’s accuracies through the inclusion of the homogeneity index were different depending on land cover classes. Earlygrowth/degraded forests, pastures, grasslands and savanna were the classes most improved, especially with the SVM radial basis function and SVM sigmoid classifiers, though with both classifiers all land cover classes were mapped with producer’s and user’s accuracies of around 90%. Our approach seems very well suited to accurately map land cover in tropical regions, thus having the potential to contribute to conservation initiatives, climate change mitigation schemes such as REDD+, and rural development policies.

Geochemical, Sedimentological And Remote Sensing Studies Of Kayamkulam Estuary, South West Coast Of India- A Gis Approach

In this study, an attempt has been made to find the textural, geochemical, sedimentological characteristics of sediments and water phases of the kayamkulam estuary located in the Southwest coast of Kerala, besides the impact of gas based thermal power plant located at the northern part of the estuary. Estuaries are an important stage in the transport of the solid weathering product of the earth’s crust. These weathered products or sediments are complex mixtures of a number of solid phases that may include clays, silica, organic matter, metal oxides, carbonates, sulfides and a number of minerals. Studies on the aquatic systems revealed the fact that it posses severe ecological impairments due to heavy discharge of sediments from 44 rivers, the continued disposal of pollutants rich materials from industries, sewage channels, agricultural areas and retting yards

Studies on the Nature and Chemistry of Sediments and Water of Periyar and Chalakudy Rivers, Kerala, India

The present study is an attempt to address issues related to sediment properties like texture, mineralogy and geochemistry as well as water quality of two important rivers of central Kerala-the Periyar and the Chalakudy rivers. The main objectives of the study are to investigate the textural and mineralogical characteristics as well as transportation and depositional mechanisms of the sediments of Periyar and Chalakudy rivers, to find out the geochemical variability of organic carbon, phosphorus and certain major (Na,K,Ca and Mg) and minor/trace(Mn,Pb,Ni,Cr, and Zn) elements in the bulk sediments and mud fraction of these rivers, to evaluate the status of heavy metal pollution registered in the sediments of these rivers, to assess the physico-chemical characteristics and water quality of Periyar and Chalakudy rivers and to estimate the dissolved nutrient flux through the Periyar and Chalakudy rivers into the receiving coastal waters. The granulometric characteristics as well as statistical parameters of the sediments of Periyar and Chalakudy rivers depend on the flow pattern controlled by the gradient of the terrain. Compared to Periyar, fluctuations in the dispersal of particles are more in Chalakudy river. In Periyar river, the P and Fe in bulk sediments show a positive correlation with C-org, while in Chalakudy river, both the elements are related to THM concentration. In general, C-org, Fe and P Shows an increasing trend downstream. In Periyar river, the P and Fe in bulk sediments show a positive correlation with C-org, while in Chalakudy river, both the elements are related to THM concentration. Among these two rivers, the pollution of water is several fold higher in Periyar river due to influx due to influx of considerable quantity of liquid and solid wastes of industrial/domestic/urban origin. Nutrient analysis reveals 2-3 times increase in N and P during monsoon season whereas SiO2-Si shows a decreasing trend.

Studies on Modified Atmosphere Packaging of Pearl Spot (Etroplussuratensis) With Special Emphasis to Biochemical and Microbiological Parameters

A modified atmosphere may be defined as a packaging or storage of a perishable product in an atmosphere other than that of air. A modified atmosphere (MA) applies to food packaged products changes continuously throughout the storage period. The pearl spot (Etroplus suratensis) is an important brackish water fish belonging to the family Cichlidae. The present work was carried out to see the effect of modified atmosphere packaging on the shelf life fresh pearl spot stored in ice to extent the shelf life. The objectives of the present study are to study the suitability of Thermoformed Trays for modified atmosphere packaging, to standardize the most suitable gas mixture for modified atmosphere packaging pearl spot based on sensory evaluation, to find out the effect of modified atmosphere packaging in comparison to air packaging, to study the biochemical, microbiological, sensory and textural characteristics during storage, to study the safety concern regarding the Clostridium botulinum during modified atmosphere packaging, to find out the most suitable chemical quality indices for modified atmosphere stored pearl spot

ENGINEERING HIERARCHICAL MESO-/MICROPOROUS LAMELLAR ZEOLITES WITH VARIABLE TEXTURAL AND CATALYTIC PROPERTIES

Meso-/microporous zeolites combine the charactersitics of well-defined micropores of zeolite with efficient mass transfer consequences of mesopores to increase the efficiency of the catalysts in reactions involving bulky molecules. Different methods such as demetallation and templating have been explored for the synthesis of meso-/microporous zeolites. However, they all have limitations in production of meso-/microporous zeolites with tunable textural and catalytic properties using few synthesis steps. To address this challenge, a simple one-step dual template synthesis approach has been developed in this work to engineer lamellar meso-/microporous zeolites structures with tunable textural and catalytic properties. First, one-step dual template synthesis of meso-/microporous mordenite framework inverted (MFI) zeolite structures was investigated. Tetrapropyl ammonium hydroxide (TPAOH) and diquaternary ammonium surfactant ([C22H45-N+(CH3)2-C6H12-N+(CH3)2-C6H13]Br2, C22-6-6) were used as templates to produce micropores and mesopores, respectively. The variation in concentration ratios of dual templates and hydrothermal synthesis conditions resulted in production of multi-lamellar MFI and the hybrid lamellar-bulk MFI (HLBM) zeolite structures. The relationship between the morphology, porosity, acidity, and catalytic properties of these catalysts was systematically studied. Then, the validity of the proposed synthesis approach for production of other types of zeolites composites was examined by creating a meso-/microporous bulk polymorph A (BEA)-lamellar MFI (BBLM) composite. The resulted composite samples showed higher catalytic stability compared to their single component zeolites. The studies demonstrated the high potential of the one-step dual template synthesis procedure for engineering the textural and catalytic properties of the synthesized zeolites.