Vers une compréhension mécanistique de la biocatalyse des composés pharmaceutiques dans des matrices complexes par traitement fongique (Trametes hirsuta)

La présence des contaminants organiques dans l’environnement est une problématique aux enjeux aussi bien scientifiques que politiques. Le caractère diffus et continu (différentes et multiples sources) de cette contamination ne permet pas à ces molécules biologiquement actives d’être soumises à une législation. Ces molécules, pouvant être très récalcitrantes, ne sont pas systématiquement éliminées par les systèmes de traitement des eaux conventionnels. Actuellement, de nouveaux procédés biotechnologiques basés sur des enzymes extracellulaires (e.g. Laccase) ou des champignons lignivores permettent l’élimination des composés les plus récalcitrants. Notre compréhension des mécanismes impliqués dans cette élimination reste incomplète. En effet, la biosorption et l’activité des enzymes extracellulaire sont les mécanismes les plus souvent mis en avant pour expliquer l’efficacité des procédés d’élimination fongique, mais ne sont pas capables d’expliquer les performances obtenues pour certains composés pharmaceutiques. Ces lacunes dans nos connaissances sur les mécanismes responsables de l’élimination fongique des contaminants organiques sont un frein à la pleine exploitation de ces procédés de traitement. De plus, il est forcé d’admettre qu’un grand nombre de travaux portant sur l’élimination fongique de contaminants organiques ont été réalisés dans des conditions de hautes concentrations, qui peuvent être peu représentatives des matrices environnementales. Ainsi, les effets observés à plus forte concentration peuvent etre le résultat dû au stress de l’organisme au contact des contaminants (toxicités). Cette thèse adresse deux questions ; ainsi quelle est l’influence des concentrations traces sur de tels procédés ? Et comment expliquer l’élimination de certains contaminants organiques lors des traitements fongiques ? Afin d’apporter des éléments de réponse sur les mécanismes mis en jeux lors de l’élimination fongique, les travaux présentés ici ont été réalisés sur un modèle de champignon lignivore connu pour ses propriétés en bioremediation. Dans un premier temps, un développement analytique permettant la quantification d’une sélection de contaminants organiques à l’état de traces a été réalisé. Cette méthode a permis d’effectuer des analyses de ces molécules à partir d’un seul échantillon environnemental de faible biomasse et à partir d’une seule injection instrumentale. Les résultats de cette thèse démontrent que l’élimination fongique de contaminants organiques résulte de mécanismes plus complexes que précédemment décrits. Notamment, la dégradation est fortement dépendante d’une étape initiale d’internalisation du contaminant par l’organisme ciblé et de la dégradation intracellulaire. Les mécanismes impliqués peuvent ainsi donnés lieux à des réactions de conjugaison intracellulaire des molecules (glucuronide, glutathione). Les résultats démontrent également que ces procédés d’élimination fongique sont efficaces sur une large gamme de concentration en contaminants organiques. Cependant, les faibles concentrations modifient les propriétés physico-chimiques et biologiques de l’organisme testé (i.e. un changement de la morphologie et du profil de la production enzymatique). La réponse biologique n’étant pas directement proportionnelle a l’exposition en contaminant. Cette étude a permis d’accroitre notre compréhension des mécanismes impliqués dans la dégradation fongique de contaminants organiques. Ceci ouvre la voie à de nouvelles études portant sur les interactions entre processus intra — et extracellulaires. Cette thèse contribue également à l’amélioration des connaissances en offrant des outils de compréhension nécessaire à l’optimisation et au développement du potentiel de ces procédés biotechnologiques (ciblage et role des enzymes réeellement impliquées dans les réactions de biocatalyse).

Multilayer structured carbon nanotubes/poly-L-lysine/laccase composite cathode for glucose/O-2 biofuel cell

Multilayer film of laccase, poly-L-lysine (PLL) and multi-walled carbon nanotubes (MWNTs) were prepared by a layer-by-layer self-assembly technique. The results of the UV-vis spectroscopy and scanning electron microscopy studies demonstrated a uniform growth of the multilayer. The catalytic behavior of the modified electrode was investigated. The (MWNTs/PLL/laccase)(n) multilayer modified electrode catalyzed four-electron reduction of O-2 to water, without any mediator.

A biofuel cell with enhanced performance by multilayer biocatalyst immobilized on highly ordered macroporous electrode

A one-compartment glucose/O-2. biofuel cell based on an electrostatic layer-by-layer (LbL) technique on three-dimensional ordered macroporous (3DOM) gold electrode was described. A 3DOM gold electrode was synthesized electrochemically by an inverted colloidal crystal template technique. Then the macroporous gold electrodes were functionalized with Au nanoparticles (AuNPs) and enzyme, glucose dehydrogenase (GDH) or laccase.

Degradation of lignin and other 14C-labelled compounds in compost and soil with an emphasis on white-rot fungi

Puu, ruohokasvit ja näistä tehdyt tuotteet kuten mekaanisesta massasta valmistettu sanomalehtipaperi sisältävät ligniiniä, joka hajoaa yleensä hyvin hitaasti luonnossa. Valkolahosienet hajottavat ligniiniä tehokkaimmin, ja koska niiden tuottamat entsyymit hajottavat myös muita vaikeasti hajoavia yhdisteitä, voidaan valkolahosienten avulla mahdollisesti puhdistaa saastuneita maita. Tässä työssä haluttiin selvittää, säilyttävätkö valkolahosienet (Abortiporus biennis, Bjerkandera adusta, Dichomitus squalens, Phanerochaete chrysosporium, Phanerochaete sordida, Phlebia radiata, Pleurotus ostreatus, Trametes hirsuta ja Trametes versicolor) aktiivisuutensa ja kasvavatko ne maassa. Aktiivisuutta mitattiin seuraamalla sienten synteettisen ligniinin (14C-DHP) hajotuskykyä. T. versicolor (silkkivyökääpä) osoittautui tehokkaimmaksi ligniinin hajottajaksi ja sen pentakloorifenolin (PCP) hajotuskykyä tutkittiin erillisessä kokeessa. Entiset tai pitkään käytössä olleet saha-alueet ovat yhä saastuneet puun käsittelyaineista peräisin olevilla kloorifenoleilla. Biohajoavien muovien kehitystyö sekä kompostoinnin yleistyminen jätteiden käsittelymenetelmänä ovat luoneet tarpeen materiaalien biohajoavuuden määrittämiseen. Euroopan standardisoimisjärjestön (CEN) kontrolloidussa kompostitestissä biohajoavuus määritetään materiaalin hajoamisen aikana muodostuvan hiilidioksidin perusteella. Hiilidioksidin tuotto mitataan sekä näytettä sisältävästä kompostista että kompostista ilman näytettä, ja tällöin oletetaan, että kompostin orgaaninen aines molemmissa komposteissa (tausta) tuottaa yhtä paljon hiilidioksidia. Testin puutteeksi saattaa osoittautua kompostissa tai maassa esiintyvä "priming effect". Tällä tarkoitetaan materiaalin lisäämisen jälkeen esiintyvää epänormaalin suurita tai pientä hiilidioksidin muodostusta, minkä seurauksena testin tulosksena saatava biohajoavuus on virheellinen. Ligniinin hajotessa muodostuu enemmän humusta kuin hiilidioksidia, koska ligniini on humuksen tärkein lähtöaine. Näin ollen ligniiniä sisältävät paperituotteet saattavat testin mukaan vaikuttaa biologisesti hajoamattomilta. Valkolahosienet hajottivat 4-23% ligniinistä hiilidioksidiksi ja T. versicolor 29% PCP:sta. Kompostissa ligniini hajosi hiilidioksidiksi 58°C:ssa huomattavasti vähemmän (8%) kuin lämpötiloissa 35°C ja 50°C (23-24%). Kompostin todennäköisesti tärkeimpien ligniinin hajottajien, termofiilisten sienten, tyypillinen optimilämpötila on 45°C, eivätkä ne ole enää aktiivisia 58°C:ssa. Sekä maassa että kompostissa ligniini sitoutui kuitenkin suurimmaksi osaksi humukseen. Valkolahosienet hajottivat sekä humukseen sitoutunutta ligniiniä että PCP:ia, mutta kompostin sekapopulaatio ei tähän pystynyt, ja ligniiniä sitoutui humukseen yhä enemmän kompostoinnin aikana. T. versicolor hajotti PCP:ia tehokkaasti, eikä se tuottanut myrkyllisiä kloorianisoleja, joita jotkut valkolahosienet saattavat muodostaa kloorifenoleista. Priming effect ilmiötä tutkittiin eri ikäisissä ja kypsyydeltään erilaisissa komposteissa. Kompostit erosvat toisistaan myös hajoamattoman jätteen määrän ja mikrobipopulaation suhteen. Negatiivinen priming effect havaittiin kaikissa epästabiileissa komposteissa (ikä enintään 6 kk), ja sen lisäksi yhdessä näistä komposteista positiivinen priming effect kokeen lopussa. Stabiileissa komposteissa (ikä vähintään 6 kk) ilmiötä ei sen sijaan havaittu. Epästabiileissa komposteissa biohajoavuudelle saadut tulokset eivät siis ole luotettavia. Työn tulosten perusteella valkolahosienet, ja erityisesti T. versicolor, ovat lupaavia saastuneen maan puhdistukseen, joskin sienirihmaston mahdollisuudet säilyä aktiivisena maan alkuperäisen mikrobipopulaation kanssa täytyy vielä selvittää. Kompostin sekapopulaatio, joka ei sisällä valkolahosieniä, hajotti ligniiniä yllättävän tehokkaasti termofiilisille sienille sopivissa lämpötiloissa, vaikka ligniini sitoutuikin pääasiallisesti humukseen. Kompostin kypsyys osoittautui tärkeäksi tekijäksi kontrolloidun kompostitestin onnistumisen kannalta. Priming effect ilmiön välttämiseksi on varmistettava, että testissä käytetty komposti on riittävän kypsä. Kompostien mikrobipopulaation koostumusta kompostoinnin eri vaiheissa tulisi tarkemmin selvittää, koska stabiilien ja epästabiilien kompostien ero aiheutui todennäköisesti populaatioiden rakenteessa vallitsevista eroista. Näin myös priming effect ilmiön syyt voitaisiin selittää paremmin.

Enhanced laccase stability through mediator partitioning into hydrophobic ionic liquids

Laccase-mediator systems have numerous potential uses for green oxidations, but their practical use may be limited because the reactive, oxidised mediators deactivate the enzyme. TEMPO, 4-hydroxybenzyl alcohol, phenothiazine and 2-hydroxybiphenyl caused almost complete deactivation of laccase from Trametes versicolor within 24-140 h. By contrast, 18% activity was retained after 188 h in controls without mediator, and 15% in the presence of ABTS. A biphasic reaction system was developed to protect the laccase, by partitioning the mediator into water-immiscible ionic liquids. In the presence of [C mim][AOT], laccase retained 54, 35, 35 and 41% activity after 188 h in the presence of 4-hydroxybenzyl alcohol, phenothiazine and 2-hydroxybiphenyl and ABTS, respectively, whilst 30% activity was retained in the presence of [N][Sac] and TEMPO. The protection against deactivation by the mediators correlated strongly with the distribution coefficients of the mediators between ionic liquids and water. © 2014 The Royal Society of Chemistry.

Covalent immobilization of laccase in green coconut fiber and use in clarification of apple juice

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

组合白腐真菌预处理木质纤维素原料的研究

木质纤维素原料种类多、分布广、数量巨大，通过燃料乙醇生产技术、厌氧沼气发酵技术将其转化成乙醇、沼气等二次能源，一定程度上可以缓解化石能源的不断消耗所带来的能源危机，也解决了农林废弃物引起的环境污染问题。其中以木质纤维素原料生产燃料乙醇，还可以避免以淀粉类和糖类原料生产燃料乙醇时带来的“与人争粮”等一系列问题。因此具有重要的经济效益、环境效益和社会效益。 然而，木质纤维素原料结构致密，木质素包裹在纤维素、半纤维素外围，导致其很难被降解利用，必须进行适当的预处理，去除木质素，打破原有的致密结构，利于原料的后续利用。因此，预处理成为木质纤维素原料能源化利用的关键。而目前预处理环节的费用过于昂贵，于是寻找一种高效、低成本的预处理方法是当今研究的热点。 本论文采用组合白腐真菌对木质纤维素原料进行生物预处理研究，与其他物理化学法相比，该法有着专一性较强、反应温和、不造成环境污染、成本低等优势。白腐真菌主要通过分泌木质素降解酶对木质素进行降解，从而破坏原料的致密结构，提高后续利用效率。所以木质素降解酶酶活的高低是影响原料预处理效果的一个关键因素。于是本论文首先通过将白腐真菌进行组合的方式提高木质素降解酶（漆酶，Lac）酶活；接着对组合菌的菌株相互作用机理进行研究，阐明组合菌Lac 酶活提高的原因，为菌株组合提高Lac 酶活这种方法的应用提供理论依据，同时也为后续组合白腐真菌预处理木质纤维素原料提供指导；进一步采用固态发酵和木质素降解酶两种方式对木质纤维素原料进行预处理研究，最大化去除木质素成分，破坏原料的致密结构；最终对预处理后原料的酶解糖化进行初步研究，为原料后续的能源化应用奠定基础。具体研究结果如下： （1） 以实验室保存的三株主要分泌Lac 的白腐真菌为出发菌株，筛选得到一组Lac 酶活明显提高的组合菌55+m-6，其中菌株55 为Trametes trogii sp.，m-6 为Trametes versicolor sp.，组合后Lac 酶活较单菌株分别提高24.13倍和4.07 倍。组合菌的最适产酶条件为pH 6.5、C/N 16:1、Tween 80 添加量为0.01%，在该条件下组合菌的Lac 酶活峰值比未优化时提高4.11倍。 （2） 对组合菌55+m-6 菌株间相互作用机理进行研究，发现菌株之间不存在抑制作用；平板培养时，菌丝交界处Lac 酶活最高并分泌棕色色素；液体培养时，菌株m-6 对组合后Lac 酶活的提高起着更为重要的作用：菌株m-6的菌块、过滤灭菌胞外物以及高温灭菌胞外物均能明显刺激菌株55 的Lac产生；菌株55、m-6 进行组合后，同工酶种类未发生增减，但有三种Lac同工酶浓度有所提高；对菌株胞外物进行薄层层析和质谱分析，结果表明组合前后菌株胞外物中各物质在浓度上存在较大的变化。推测组合菌Lac酶活的明显提高，主要是由于菌株m-6 胞外物中的一些物质能刺激菌株55 分泌大量Lac 进行代谢，且这些刺激物质并非菌株m-6 特有，菌株55自身也可以代谢生成，但是适当的浓度才能刺激Lac 的大量分泌。 （3） 将组合菌55+m-6 用于固态发酵预处理木质纤维素原料，发现其对玉米秆的降解程度最大，在粉碎度40 目、含水率65%的最优处理条件下，处理至第15d，秸秆失重率为41.24%，其中木质素、纤维素、半纤维素均有降解，且Lac 和纤维素酶（CMC）酶活以及还原糖量均达到峰值。 （4） 对玉米秆进行木质素降解酶预处理，发现Lac/1-羟基苯并三唑（HBT）系统对玉米秆木质素的降解效果最好，在最优处理条件时，即HBT 用量0.2%、处理时间1d、Lac 用量50U/g，木质素降解率可达12.60%。预处理后玉米秆的致密结构被破坏，比表面积增大，利于后续酶与纤维素、半纤维素成分的结合。 （5） 对预处理后的玉米秆进行酶解糖化，其中组合菌固态发酵预处理后玉米秆的糖化率比对照高4.33 倍；Lac/HBT 系统预处理后玉米秆的糖化率比对照高2.99％，糖化液中主要含有木糖、葡萄糖两种单糖。 There are many kinds and large quantities of lignocellulosic biomass widely distributed on the earth. They can be converted into secondary energy such as fuel ethanol, biogas, et al., which can relieve the energy crisis caused by consumption of fossil energy resources and solve the problem of environmental pollution caused by agriculture and forestry waste. Meanwhile, the production of fuel ethanol from lignocellulosic biomass can ensure food supply to human kind instead of starch- and sugar-containing raw materials. So the energy conversion of lignocellulosic biomass contributes considerable economic, environment and social benefits. However, lignocellulosic biomass has the compact structure, in which lignin surrounds cellulose and hemicellulose, so it must be pretreated before energy usage and pretreatment is one of the most critical steps in the energy conversion of lignocellulosic biomass. At present, the cost of pretreatment is too expensive, so looking for an efficient and low-cost pre-treatment method is one of recent research hot spots. In this research, combined white rot fungi pretreatment method was used, which had some advantages in low cost, high specificity, mild reacting conditions and friendly environmental effects compared with the other physical and chemical methods. White rot fungi secrete lignin degrading enzymes to degrade the content of lignin and damage the contact structure of lignocellulosic biomass, so the activity of the lignin degrading enzymes is the key factor to the degradation effect of raw materials. Firstly, the combined fungi with high laccase activity were screened; secondly, the interaction mechanism between strains was studied, and the cause of higher laccase activity after strains combination was also preliminary clarified; under the guidance of the mechanism, lignocellulosic biomass was pretreated by the combined fungi; lastly, the enzymatic hydrolysis of pretreated lignocellulosic biomass was also preliminary studied; all of the researches could lay the foundation for the energy application of lignocellulosic biomass. The specific research results were as follows: (1) The combined fungi 55+m-6 with significant higher laccase activity were screened from the three white rot fungi stored in our lab which mainly secreted laccase. Strain 55 and strain m-6 were Trametes trogii sp. and Trametes versicolor sp., respectively. The laccase activity of combined fungi was 24.13 and 4.07-fold than strain 55 and strain m-6, respectively. The optimized condition for laccase production of the combined fungi in liquid medium was pH 6.5, C/N 16:1 and Tween 80 0.01%. In this optimized condition, the laccase activity of combined fungi was 4.11-fold higher comparing with which in non-optimized medium. (2) The interaction mechanism between strain 55 and strain m-6 was further studied, and no inhibition effect was observed. Brown pigment was secreted on the junction of the two strains on the plate, where the highest laccase activity was detected. Strain m-6 was much important to boost laccase activity of combined fungi in liquid medium, and strain 55 was stimulated by fungal plug, filter sterilized extracellular substances and high temperature sterilized extracellular substances of strain m-6 to produce laccase. The types of laccase isozymes did not change after combining strain 55 and strain m-6, but the concentrations of three types increased. Mass Spectrometry and TLC analysis of extracellular substances of each strain showed that concentration of some substances considerably changed after strains were combined. It was supposed that the cause of higher laccase activity of combined fungi was mainly due to some extracellular substances of strain m-6 with the appropriate concentration which stimulated laccase secretion of strain 55 and generated not only by strain m-6 but also by strain 55. (3) Combined fungi 55+m-6 were used to lignocellulosic biomass pretreatment with the type of solid-state fermentation. The highest degree of degradation of corn straw was obtained, including the rate of weight loss was 41.24% and the lignin, cellulose and hemicellulose were degraded partially under the optimized condition of 40 mesh, 65% water content on 15th day. Laccase, CMCase activities and content of reducing sugar reached the maximum value on that day. (4) Lignin degrading enzymes from combined fungi 55+m-6 were used for corn straw pretreatment. The most remarkable degradation of lignin in corn straw with Lac/1-hydroxybenzotriazole (HBT) system was observed, and the 12.60% lignin degradation was obtained under the optimized condition of 0.2% HBT, 50 U/g laccase for 1 d. After pretreated by Lac/HBT, the tight structure of corn straw was demolished and specific surface area increased, which had advantages for accessible of enzyme to cellulose and hemicellulose. (5) The corn straws pretreated by combined fungi 55+m-6 with the type of solid-state fermentation and Lac/HBT were used for enzymatic hydrolysis, and the saccharification rates of each pretreatment type were 4.33 times and 2.99% higher than CK, respectively. The enzymatic hydrolysis liquid of corn straw pretreated by Lac/HBT mainly contained xylose and glucose.

Electrochemical characteristics of mediated laccase-catalysis and electrochemical detection of environmental pollutants

Laccase has been immobilized on the carbon nanotubes modified glassy carbon electrode surface by adsorption. As-prepared laccase retains good electrocatalytic activity to oxygen reduction by using 2,2'-azino-bis-(3-ethylbenzthiazoline-6-sulfonic acid) as the mediator. It can be used as a biosensor for the determination of catechol with broad linear range.

Electrochemical catalysis and thermal stability characterization of laccase-carbon nanotubes-ionic liquid nanocomposite modified graphite electrode

The hydrophobic carbon nanotubes-ionic liquid (CNTs-IL) get forms a stable modified film on hydrophobic graphite electrode surface. Laccase immobilized on the CNTs-IL gel film modified electrode shows good thermal stability and enhanced electrochemical catalytic ability. The optimal bioactivity occurs with increasing temperature and this optimum is 20 degrees C higher in comparison to free laccase. The improvement of laccase thermal stability may be due to the microenvironment of hydrophobic CNTs-IL gel on graphite electrode surface. On the other hand, the sensitive detection of oxygen has been achieved due to the feasibility of oxygen reduction by both of laccase and nanocomposite of CNTs-IL gel. Furthermore, the laccase hybrid nanocomposite also shows the fast electrochemical response and high sensitivity to the inhibitors of halide ions with the approximate IC50 of 0.01, 4.2 and 87.5 mM for the fluoride, chloride and bromide ions, respectively. It implies the feasibility of laccase modified electrode as an inhibition biosensor to detect the modulators of laccase.

Facile preparation of amperometric laccase biosensor with multifunction based on the matrix of carbon nanotubes-chitosan composite

The carbon nanotubes-chitosan (CNTs-CS) composite provides a suitable biosensing matrix due to its good conductivity, high stability, and good biocompatibility. Enzymes can be firmly incorporated into the matrix without the aid of other cross-linking reagents. The composite is easy to form insoluble film in solution above pH 6.3. Based on this, a facilely fabricated amperometric biosensor by entrapping laccase into the CNTs-CS composite film has been developed. At pH 6.0, the fungi laccase incorporated into the composite film remains better catalytic activity than that dissolved in solution. The system is in favor of the accessibility of substrate to the active site of laccase, thus the affinity to substrates is improved greatly, such as 2,2'-azino-bis-(3-ethylbenzthiazoline-6-sulfonic acid) diammonium salt (ABTS), catechol, and 0, with K. values of 19.86 mu M, 9.43 mu M, and 3.22 mM, respectively. The major advantages of the as-prepared biosensor are: detecting different substrates (ABTS, catechol, and 02), possessing high affinity and sensitivity, durable long-term stability, and facile preparation procedure. On the other hand, the system can be applied in fabrication of biofuel cells as the cathodic catalysts based on its good electrocatalysis for oxygen reduction.

Growth, dye degradation and ligninolytic activity studies on Zimbabwean white rot fungi

White rot fungi were collected from Chirinda and Chimanimani hardwood forests in Zimbabwe and studied with respect to growth temperature optima and dye decolorization. Temperature optima were found to vary (between 25-37 degreesC) amongst the isolates. The isolates were screened for their ability to degrade the polymeric dyes; blue dextran and Poly R478 and the triphenylmethane dyes; cresol red, crystal violet and bromophenol blue. Semi-quantitative determination of the hydrolytic enzyme activities possessed by the white rot fungi was determined using the API ZYM system. Lignin peroxidase (LiP), manganese peroxidase (MnP) and laccase activities in the fungi were also determined. No LiP was detected in any of the isolates but all isolates showed manganese peroxidase and laccase activities. Time related decolorization studies and optimum pH determinations for Poly R478 degradation by the isolates were carried out in liquid cultures. The most significant rates of Poly R478 decolorization in liquid cultures were found with the following isolates: Trametes cingulata, Trametes versicolor, Trametes pocas, DSPM95 (a species to be identified), Datronia concentrica and Pyenoporus sanguineus. (C) 2001 Elsevier Science Inc. All rights reserved.