A 12 kW three-phase low THD rectifier with high-frequency isolation and regulated DC output

A robust 12 kW rectifier with low THD in the line currents, based on an 18-pulse transformer arrangement with reduced kVA capacities followed by a high-frequency isolation stage is presented in this work. Three full-bridge (buck-based) converters are used to allow galvanic isolation and to balance the dc-link currents, without current sensing or current controller. The topology provides a regulated dc output with a very simple and well-known control strategy and natural three-phase power factor correction. The phase-shift PWM technique, with zero-voltage switching is used for the high-frequency dc-dc stage. Analytical results from Fourier analysis of winding currents and the vector diagram of winding voltages are presented. Experimental results from a 12 kW prototype are shown in the paper to verify the efficiency, robustness and simplicity of the command circuitry to the proposed concept.

A new three-phase low THD power supply with high-frequency isolation and 60V/200A regulated DC output

This work proposes a new isolated high power factor 12kW power supply based on an 18-pulse transformer arrangement. Three full-bridge converters are used for isolation and to balance the DC-link currents, without current sensing or a current controller. The topology provides a regulated DC output with a very simple control strategy. Simulation and experimental results are presented in this paper.

Hybrid three-phase HPF rectifier with programmable input current THD, using FPGA device and VHDL language

In this paper is proposed and analyzed a digital hysteresis modulation using a FPGA (Field Programmable Gate Array) device and VHDL (Hardware Description Language), applied at a hybrid three-phase rectifier with almost unitary input power factor, composed by parallel SEPIC controlled single-phase rectifiers connected to each leg of a standard 6-pulses uncontrolled diode rectifier. The digital control allows a programmable THD (Total Harmonic Distortion) at the input currents, and it makes possible that the power rating of the switching-mode converters, connected in parallel, can be a small fraction of the total average output power, in order to obtain a compact converter, reduced input current THD and almost unitary input power factor. Finally, the proposed digital control, using a FPGA device and VHDL, offers an important flexibility for the associated control technique, in order to obtain a programmable PFC (Power Factor Correction) hybrid three-phase rectifier, in agreement with the international standards (IEC, and IEEE), which impose limits for the THD of the AC (Alternate Current) line input currents. The proposed strategy is verified by experiments. © 2008 IEEE.

Proposal of a hybrid rectifier structure with HPF and low THD suitable for front-end trolleybuses systems supplied by AC distribution networks

This paper presents the development and the experimental analysis of a new single-phase hybrid rectifier structure with high power factor (PF) and low harmonic distortion of current (THDI), suitable for application in traction systems of electrical vehicles pulled by electrical motors (trolleybus), which are powered by urban distribution network. This front-end rectifier structure is capable of providing significant improvements in trolleybuses systems and in the urban distribution network costs, and efficiency. The proposed structure is composed by an ordinary single-phase diode rectifier with parallel connection of a switched converter. It is outlined that the switched converter is capable of composing the input line current waveform assuring high power factor (HPF) and low THDI, as well as ordinary front-end converter. However, the power rating of the switched converter is about 34% of the total output power, assuring robustness and reliability. Therefore, the proposed structure was named single-phase HPF hybrid rectifier. A prototype rated at 15kW was developed and analyzed in laboratory. It was found that the input line current harmonic spectrum is in accordance with the harmonic limits imposed by IEC61000-3-4. The principle of operation, the mathematical analysis, the PWM control strategy, and experimental results are also presented in this paper. © 2009 IEEE.

Desarterialização transanal guiada por doppler associada ao reparo anorretal na doença hemorroidária: a técnica do THD

INTRODUÇÃO: O tratamento cirúrgico para hemorroidas deve ter indicação individual e baseia-se no sintoma predominante (sangramento ou prolapso), na gravidade da doença e na presença ou ausência de componente externo (plicoma). Cabe ao cirurgião conhecer as mais variadas técnicas para que possa encontrar o tratamento mais adequado caso a caso. TÉCNICA: O procedimento THD consiste na ligadura alta seletiva e guiada por Doppler de até seis ramos arteriais submucosos que irrigam as hemorroidas, levando à sua desarterialização, associada à correção do prolapso (reparo anorretal ou lifting). Utiliza equipamento e kit especiais. CONCLUSÃO: A técnica do THD tem mostrado bons resultados iniciais. Por ser técnica cirúrgica em que se respeita a anatomia, ela age diretamente sobre a fisiopatologia da afecção e corrige suas principais consequências, ela parece bastante promissora. Sua aplicação inicial pode ser nos pacientes com doença hemorroidária de II grau, que tenham indicação de tratamento cirúrgico, e de III e IV graus, nestes últimos, podendo ser associada à ressecção de plicomas.

Stereoselective analysis of thioridazine-2-sulfoxide and thioridazine-5-sulfoxide: An investigation of rac-thioridazine biotransformation by some endophytic fungi

The purpose of this study was to develop a method for the stereoselective analysis of thioridazine-2-sulfoxide (THD-2-SO) and thioridazine-5-sulfoxide (THD-5-SO) in culture medium and to study the biotransformation of rac-thioridazine (THD) by some endophytic fungi. The simultaneous resolution of THD-2-SO and THD-5-SO diastereoisomers was performed on a CHIRALPAK(R) AS column using a mobile phase of hexane: ethanol: methanol (92:6:2, v/v/v) + 0.5% diethylamine; UV detection was carried out at 262 nm. Diethyl ether was used as extractor solvent. The validated method was used to evaluate the biotransformation of THD by 12 endophytic fungi isolated from Tithonia diversifolia, Viguiera arenaria and Viguiera robusta. Among the 12 fungi evaluated, 4 of them deserve prominence for presenting an evidenced stereoselective biotransformation potential: Phomopsis sp. (TD2) presented greater mono-2-sulfoxidation to the form (S)-(SE) (12.1%); Glomerella cingulata (VA1) presented greater mono-5-sulfoxidation to the forms (S)-(SE) + (R)-(FE) (10.5%); Diaporthe phaseolorum (VR4) presented greater mono-2-sulfoxidation to the forms (S)-(SE) and (R)-(FE) (84.4% and 82.5%, respectively) and Aspergillus fumigatus (VR12) presented greater mono-2-sulfoxidation to the forms (S)-(SE) and (R)-(SE) (31.5% and 34.4%, respectively). (C) 2007 Elsevier B.V. All rights reserved.

Assignment of the absolute configuration at the sulfur atom of thioridazine metabolites by the analysis of their chiroptical properties: The case of thioridazine 2-sulfoxide

Thioridazine (THD) is a commonly prescribed phenotiazine neuroleptic drug, which is extensively biotransformed in the organism producing as main metabolites sulfoxides and a sulfone by sulfur oxidation Significant differences have been observed in the activity of the THD enantiomers as well as for its main metabolites, and enantioselectivity phenomena have been proved in the metabolic pathway. Here the assignment of the absolute configuration at the sulfur atom of enantiomeric THD-2-sulfoxide (THD-2-SO) has been carried out by circular dichroism (CD) spectroscopy The stereoisomers were separated by HPLC on Chiralpak AS column, recording the CD spectra for the two collected enantiomeric fractions The theoretical electronic CD spectrum has been obtained by the TDDFT/B3LYP/6-31G*. as Boltzmann averaging of the contributions calculated for the most stable conformations of the drug The comparison of the simulated and experimental spectra allowed the absolute configuration at the sulfur atom of the four THD-2-SO stereoisomers to be assigned The developed method should be useful for a reliable correlation between stereochemistry and activity and/or toxicity

Modeling, control and simulation of full-power converter wind turbines equipped with permanent magnet synchronous generator

In this paper, two wind turbines equipped with a permanent magnet synchronous generator (PMSG) and respectively with a two-level or a multilevel converter are simulated in order to access the malfunction transient performance. Three different drive train mass models, respectively, one, two and three mass models, are considered in order to model the bending flexibility of the blades. Moreover, a fractional-order control strategy is studied comparatively to a classical integer-order control strategy. Computer simulations are carried out, and conclusions about the total harmonic distortion (THD) of the electric current injected into the electric grid are in favor of the fractional-order control strategy.

Projeto e implementação de um pré-regulador de fator de potência com controlo digital

Hoje em dia as fontes de alimentação possuem correção do fator de potência, devido às diversas normas regulamentares existentes, que introduziram grandes restrições no que respeita à distorção harmónica (THD) e fator de potência (FP). Este trabalho trata da análise, desenvolvimento e implementação de um Pré-Regulador de fator de potência com controlo digital. O controlo digital de conversores com recurso a processamento digital de sinal tem vindo a ser ao longo dos últimos anos, objeto de investigação e desenvolvimento, estando constantemente a surgirem modificações nas topologias existentes. Esta dissertação tem como objetivo estudar e implementar um Pré-Regulador Retificador Boost e o respetivo controlo digital. O controlo do conversor é feito através da técnica dos valores médios instantâneos da corrente de entrada, desenvolvido através da linguagem de descrição de hardware VHDL (VHSIC HDL – Very High Speed Integrated Circuit Hardware Description Language) e implementado num dispositivo FPGA (Field Programmable Gate Array) Spartan-3E. Neste trabalho são apresentadas análises matemáticas, para a obtenção das funções de transferência pertinentes ao projeto dos controladores. Para efetuar este controlo é necessário adquirir os sinais da corrente de entrada, tensão de entrada e tensão de saída. O sinal resultante do módulo de controlo é um sinal de PWM com valor de fator de ciclo variável ao longo do tempo. O projeto é simulado e validado através da plataforma MatLab/Simulink e PSIM, onde são apresentados resultados para o regime permanente e para transitórios da carga e da tensão de alimentação. Finalmente, o Pré-Regulador Retificador Boost controlado de forma digital é implementado em laboratório. Os resultados experimentais são apresentados para validar a metodologia e o projeto desenvolvidos.

Power-and-area efficient 14-bit 1.5 MSample/s two-stage algorithmic ADC based on a mismatch-insensitive MDAC

IEEE International Symposium on Circuits and Systems, pp. 220 – 223, Seattle, EUA

Pipelined analog-to-digital conversion using current-mode reference shifting

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Projeto de um altifalante digital

Devido ao crescente desenvolvimento das nanotecnologias, estando associadas a melhoria da eficiência energética assim como mais processamento de dados e a redução dos custos, esta dissertação possibilita todo o enquadramento com sistemas modernos ao nível do áudio digital. Tendo como base esta perspetiva, esta dissertação apresenta um sistema de áudio completo desde a fonte do sinal digital no PC até ao sinal analógico no altifalante. O sistema é constituído pelos seguintes módulos: a interface do utilizador no PC, o Processador Digital de Sinais (DSP), o amplificador digital e os altifalantes. O sistema é baseado na amplificação de classe D controlada por um modulador sigma delta (ΣΔM) digital. São abordadas as técnicas utilizadas e os cuidados a ter em conta em cada módulo, tendo como principal objetivo uma boa qualidade de áudio. Diferentes arquiteturas ΣΔM são primeiramente analisadas por simulações para validar a estabilidade e a funcionalidade, seguidamente são implementadas ao nível físico no protótipo para qualificar algumas medições elétricas e testes acústicos básicos. Depois de selecionados os ΣΔM mais promissores, o sistema foi avaliado pela análise de alguns testes elétricos de alto nível assim como gravações do sinal de áudio em um ambiente de estúdio controlado. Os resultados acústicos são comparados com um sistema de estúdio com reconhecimento no mercado. As medições finais do protótipo revelaram valores do rendimento de até 72%, a SNR na saída do amplificador digital de 73 dB através da leitura com o Audio Precision ATS-2, com uma THD de -75 dB e uma gama dinâmica (DR) de 75 dB. A tensão de alimentação pode ir dos 5 aos 12 Volt, utilizando uma metodologia H-bridge na saída do amplificador, e podendo ser aplicada uma carga mínima de 4 Ohm. O sistema desenvolvido demonstra-se promissor e possibilita melhorias através de otimização de cada elemento em particular, desde adicionar capacidades ao DSP através de novo firmware, ou melhorar a potência do amplificador digital consoante os requisitos da aplicação.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Implementation and comparison of different switching techniques for shunt active power filters

This paper presents a comparison between three switching techniques that can be used in three-phase four-wire Shunt Active Power Filters (SAPFs). The implemented switching techniques are: Periodic-Sampling (PS), Triangular Carrier Pulse-Width Modulation (TC-PWM) and Space Vector PWM (SVPWM). The comparison between them is made in terms of the compensated currents THD%, implementation complexity, necessary CPU time and SAPF efficiency. To perform this comparison are presented and analyzed several experimental results, obtained with a 20 kVA Shunt Active Power Filter prototype, specially developed for this purpose. The control system of the developed SAPF is based in the p-q Theory with a grid synchronization algorithm p-PLL.

III - Contribuição para o estudo biológico e ecológico das Podostemaceae do salto do Piracicaba

1 - The Author, in this 3 thd. contribution, concludes the study of the biology and ecology of the species Tristicha trifaria (Willd.) Spreng. and Mourera aspera (Bong.) Tul., both of the Piracicaba Fall. 2 - According to the results of Dr. Peter van Royen (State Herbarium of Leiden, Holland), who made a complete revision of Podostemaceae of the Piracicaba Fall, the species Tristicha hypnoides (St. Hil.) Spreng. var. Hilarii Tul. and Mnioppsis Glazioviana Warm, correspond, respectively, to theTristicha trifaria (Willd.) Spreng. and Mniopsis weddelliana Tul. Apinagia Accorsii Toledo was transferred by Royen to the genus Wettsteiniola. So, its new name is Wettsteiniola accorsii (Toledo) v. Royen. 3 - Propagation by seeds may occur in the following places: a) placenta of partially open fruits; b) external and internal walls of the open capsules; c) pedicels of the fruits; d) remains of rhizomes, branches, etc. e) organic residues accumulated in water holes in the fall; f) clean rocks, in which the little groups of seedlings seems to be a colony of algae. Seeds adhere to the substrata above by means, of a mucilage produced by the transformation of the external integuments in contact with water. 4 - In the growth of the four species below it was found in Piracicaba Fall conspicuous zoning so scattered: a) Wettsteiniola accorsii (Toledo) v. Royen, in rocks situated just within the water fall, where velocity of the current and aeration of the water are very high. b) Tristicha trifaria (Willd.) Spreng. and Mniopsis weddelliana Tul., in rocks at some distance (100 m more or less) upstream until near the bridge across the river. c) Mourera aspera (Bong.) Tul., 300 m upwards the bridge. 5- During 1949, the ecological conditions of the Piracicaba Fall were changed due to the following factors: a) dry season very long, begining from last period of June until 30 november; b) stopping, during four months, of water from the Atibaia river (one of the components of Piracicaba river) near to the city of Americana, in the place where a new station of the Companhia Paulista de Força e Luz was build. In consequence, most of the Podostemaceae died. On the dry rocks there were only fruits and dried plants. 6 - Tristicha trifaria has the same biological and ecological behavior as the Mniopsis weddelliana,. 7 - The vegetative propagation of Tristicha trifaria is made by increasing of its branches, production of stolons with vegetatives buds and regeneration of old parts in especial conditions of water and aeration. 8 - Mourera aspera has the same vegetative propagation as the Wettsteiniola accorsii; it produces stolons (in very little percentage) with vegetative buds, branches of the rhizomes and regeneration of active old parts. 9 - Frequently, there is, on the plants an accumulation of sand, silt, loam, organic substances, and so on. The quantity of material stored depends of the purity of the water, of the morphology of the plants and of the situation on the fall. 10 - In extrem conditions of dry heat, the surviving of the species in its habitat depends exclusively from germination of seeds in the mentioned substrata. Exceptionally, some plants survive in a few water pockets full with the weak remaining current.