Tempering temperature effects on abrasive wear of mottled cast iron

The effects of different tempering temperatures (300-600 degrees C) on abrasive wear resistance of mottled cast iron were studied. Abrasive wear tests were carried out using the rubber-wheel test on quartz sand and the pin test on Al(2)O(3) abrasive cloths. The retained austenite content of the matrix was determined by X-ray diffraction. The wear surface of the specimens was examined by scanning electron microscopy for identifying the wear micromechanism. Bulk hardness and matrix hardness before and after the tests were measured. The results showed that in the two-body (pin-on-disc test) system, the main wear mechanism was microcutting and high matrix hardening was presented. The wear rates presented higher correlation with the retained austenite than with the bulk and matrix hardness. In the three-body system (sand-rubber wheel), the wear surfaces presented indentations due to abrasive rolling. The wear rates had better correlation with both the bulk and matrix hardness (before and after the wear test) than with the retained austenite content. There are two groups of results, high and low wear rates corresponding to each tribosystem, two-body abrasive wear and three-body abrasive wear, respectively. (C) 2009 Elsevier B.V. All rights reserved.

Hyper-parallel tempering Monte Carlo simulations of Ar adsorption in new models of microporous non-graphitizing activated carbon: effect of microporosity

The adsorption of gases on microporous carbons is still poorly understood, partly because the structure of these carbons is not well known. Here, a model of microporous carbons based on fullerene- like fragments is used as the basis for a theoretical study of Ar adsorption on carbon. First, a simulation box was constructed, containing a plausible arrangement of carbon fragments. Next, using a new Monte Carlo simulation algorithm, two types of carbon fragments were gradually placed into the initial structure to increase its microporosity. Thirty six different microporous carbon structures were generated in this way. Using the method proposed recently by Bhattacharya and Gubbins ( BG), the micropore size distributions of the obtained carbon models and the average micropore diameters were calculated. For ten chosen structures, Ar adsorption isotherms ( 87 K) were simulated via the hyper- parallel tempering Monte Carlo simulation method. The isotherms obtained in this way were described by widely applied methods of microporous carbon characterisation, i. e. Nguyen and Do, Horvath - Kawazoe, high- resolution alpha(a)s plots, adsorption potential distributions and the Dubinin - Astakhov ( DA) equation. From simulated isotherms described by the DA equation, the average micropore diameters were calculated using empirical relationships proposed by different authors and they were compared with those from the BG method.

Optimization procedures in the design of continuous induction hardening and tempering installations for magnetic steel bars

An inverse problem concerning the industrial process of steel bars hardening and tempering is considered. The associated optimization problem is formulated in terms of membership functions and, for the sake of comparison, also in terms of quadratic residuals; both geometric and electromagnetic design variables have been considered. The numerical solution is achieved by coupling a finite difference procedure for the calculation of the electromagnetic and thermal fields to a deterministic strategy of minimization based on modified Flctcher and Reeves method. © 1998 IEEE.

Two and a Half Cheers for the Midwestern Bourgeoisie: Role of the Virtues in Tempering Business Decisions

A recent book (The Bourgeois Virtues: Ethics for an Age of Commerce, D. N. McCloskey), raises the matter of the role of the virtues in business and economic choice, arguing that capitalism can indeed, be virtuous or at least better than the alternative(s). This argument is especially timely in light of the apparent excesses on Wall Street and in some banking/financial institutions. Excessive greed and often the lack of business ethics contributed in substantive ways to the financial crisis and near economic meltdown we have been experiencing. As McCloskey, (2006, pp. 1-2) argues (in setting the stage for the complex argument made in this 616-page book!): “The book … is directed toward you who are suspicious of the phrase ‘bourgeois virtues,’ pretty sure that it is a contradiction in terms. And the book is directed, with less optimism about changing their minds, toward you who think the phrase is worse: a lie. ‘Bourgeois virtues’ is neither. The claim here is that modern capitalism does not need to be offset to be good. Capitalism can on the contrary be virtuous. In a fallen world bourgeois life is not perfect. But it’s better than any available alternative. American capitalism needs to be inspirited, moralized, completed. Two and a half cheers for the Midwestern bourgeoisie (middle-class, small business owners…. yet)… Many a businessman is an ethical shell or worse. Even the virtues of the bourgeoisie, … do not lead straight to heaven.”

Tempering the EU? NGO Advocacy in the Area of Freedom, Security, and Justice

The European Union’s (EU) area of Freedom, Security and Justice (AFSJ) portfolio comprises policy areas such as immigration and asylum, and police and judicial cooperation. Steps were taken to bring this field into the mandate of the EU first by the Maastricht Treaty, followed by changes implemented by the Amsterdam and Lisbon Treaties, the last one ‘normalizing’ the EU’s erstwhile Third Pillar. As the emergent EU regime continues to consolidate in this field, NGOs of various kinds continue to seek to influence policy-making and implementation, with varying success. This article seeks to establish the context in which NGOs carry out their work and argues that the EU-NGO interface is impacted both by the institutional realities of the European Union and the capacities of EU-oriented NGOs to seize and expand opportunities for access and input into the policy cycle. Using EU instruments representing three different policy bundles in AFSJ (immigration, asylum and judicial cooperation in criminal matters), the article seeks to map out NGO strategies in engaging and oftentimes resisting European Union policy instruments.

The American steel worker; a twenty-five years' experience in the selection, annealing, working, hardening and tempering of various kinds and grades of steel,

Mode of access: Internet.

Toughness variations during the tempering of a plain carbon, martensitic steel

The aim of this paper is to present results of toughness measurements and fractographic observations made on a quenched and tempered 0. 6%, carbon steel and to use these as a basis for a discussion of the factors affecting "623K (350 °C) embrittlement" (one-step temper embrittlement).

Solid Lipid Nanoparticles For Hydrophilic Biotech Drugs: Optimization And Cell Viability Studies (caco-2 & Hepg-2 Cell Lines).

Insulin was used as model protein to developed innovative Solid Lipid Nanoparticles (SLNs) for the delivery of hydrophilic biotech drugs, with potential use in medicinal chemistry. SLNs were prepared by double emulsion with the purpose of promoting stability and enhancing the protein bioavailability. Softisan(®)100 was selected as solid lipid matrix. The surfactants (Tween(®)80, Span(®)80 and Lipoid(®)S75) and insulin were chosen applying a 2(2) factorial design with triplicate of central point, evaluating the influence of dependents variables as polydispersity index (PI), mean particle size (z-AVE), zeta potential (ZP) and encapsulation efficiency (EE) by factorial design using the ANOVA test. Therefore, thermodynamic stability, polymorphism and matrix crystallinity were checked by Differential Scanning Calorimetry (DSC) and Wide Angle X-ray Diffraction (WAXD), whereas the effect of toxicity of SLNs was check in HepG2 and Caco-2 cells. Results showed a mean particle size (z-AVE) width between 294.6 nm and 627.0 nm, a PI in the range of 0.425-0.750, ZP about -3 mV, and the EE between 38.39% and 81.20%. After tempering the bulk lipid (mimicking the end process of production), the lipid showed amorphous characteristics, with a melting point of ca. 30 °C. The toxicity of SLNs was evaluated in two distinct cell lines (HEPG-2 and Caco-2), showing to be dependent on the concentration of particles in HEPG-2 cells, while no toxicity in was reported in Caco-2 cells. SLNs were stable for 24 h in in vitro human serum albumin (HSA) solution. The resulting SLNs fabricated by double emulsion may provide a promising approach for administration of protein therapeutics and antigens.

ANNEALING EFFECTS ON THE MICROSTRUCTURE OF FERRITIC-MARTENSITIC ODS-EUROFER STEEL

Oxide dispersion strengthened (ODS) ferritic/martensitic (FM) steels are promising candidates for structural applications in future fusion power reactors. In order to evaluate the thermal stability of 80% cold-rolled ODS-EUROFER, samples were annealed for 1 h at temperatures up to about 0.9 T(m), where T(m) is the absolute melting point. The characterization of the annealed samples was performed using transmission electron microscopy and electron backscatter diffraction. Results show that static recovery is the main softening mechanism of this steel when annealed below 800 degrees C. The volume fraction of recrystallized grains is quite small (below 0.10). Above 900 degrees C, martensitic transformation takes place causing pronounced hardening. Large M(23)C(6) particles are found at the grain boundaries after tempering at 750 degrees C for 2 h.

The effect of heat treatment on the toughness, hardness and microstructure of low carbon white cast irons

The effect of destabilisation and subcritical heat treatment on the impact toughness, hardness, and the amount and mechanical stability of retained austenite in a low carbon white cast iron have been investigated. The experimental results show that the impact energy constantly increases when the destabilisation temperature is raised from 950 degreesC to 1200 degreesC. Although the hardness decreases, the heat-treated hardness is still greater than the as-cast state. After destabilisation treatment at 1130 degreesC, tempering at 200 to 250 degreesC for 3 hours leads to the highest impact toughness, and secondary hardening was observed when tempering over 400 degreesC. The amount of retained austenite increased with the increase in the destabilisation temperature, and the treatment significantly improves the mechanical stability of the retained austenite compared with the as-cast state. Tempering below 400 degreesC does not affect the amount of retained austenite and its mechanical stability. But the amount of retained austenite is dramatically reduced when tempered above 400 degreesC. The relationship between the mechanical properties and the microstructure changes was discussed. (C) 2001 Kluwer Academic Publishers.

Modelagem e simulação de um secador intermitente de fluxos contracorrentes para frutos do cafeeiro

Este trabalho foi realizado com o objetivo de desenvolver um modelo computacional para simular a secagem de frutos café em um secador intermitente de fluxos contracorrente, empregando a linguagem de simulação EXTEND™ e o Modelo de Thompson (THOMPSON; PEART; FOSTER, 1968). Para validação do modelo desenvolvido foram utilizados dados experimentais obtidos por Silva (1991), em que foram empregados três níveis de temperatura do ar de secagem de 60, 80 e 100 °C. O modelo desenvolvido foi validado, sendo constatados desvios absolutos de 1,8% b.u e 1,1 kg e erros relativos de 11% e 1,6% na previsão dos parâmetros teor de água final e consumo de lenha, respectivamente. O modelo validado foi empregado na condução de experimentos tipo comparação de cenários. O primeiro experimento refere a alterações do ciclo operacional em que foram alterados os tempos de movimentação e de parada do fluxo da massa de grãos. E o segundo refere à alteração da configuração do secador quanto às alturas das câmaras de secagem e descanso. O ciclo operacional com os tempos de movimentação de um minuto e de parada de dezesseis minutos, para a temperatura do ar de secagem de 100 °C, proporcionou o melhor desempenho, sendo constatado tempo secagem de 12,3 h, consumo de lenha de 109,5 kg, consumo específico de energia de 7660 kJ.kg-1 de água evaporada, e capacidade de secagem de 87,86 kg.h-1. Quanto à configuração do secador, o melhor desempenho ocorreu para altura da câmara de secagem de 2,3 m usando a temperatura do ar de secagem de 100 °C, em que foram simulados tempo de secagem de 12,0 h, consumo de lenha de 106,5 kg, consumo específico de energia, de 7433 kJ.kg-1 de água evaporada, e capacidade de secagem de 90 kg.h-1. Desse modo, na condução da secagem de frutos de café em um secador intermitente de fluxos contracorrentes é recomendado o ciclo operacional com tempos de movimentação de um minuto e o de parada de dezesseis minutos, e não empregar a câmara de descanso. Essa conclusão está fundamentada em índices de desempenho do secador. Ressalta-se que não foram simulados os impactos nos parâmetros de qualidade.