Desmonte de Maciços Rochosos: optimização da perfuração

Este trabalho pretende avaliar e melhorar o modo de execução da aplicação da técnica de perfuração, não comprometendo a jusante, no ciclo de operações, a qualidade do desmonte, visando assim, uma optimização técnico-económica. Este manuscrito irá centrar-se na optimização da etapa da perfuração, visando assim a optimização do ciclo total da perfuração. As tarefas realizadas numa pedreira constituem um ciclo de operações. Uma das operações envolvidas no desmonte de maciços rochosos é a perfuração. A forma como esta é executada é determinante para o sucesso do desmonte. O correcto dimensionamento dos acessórios de perfuração, afiação de bits, manutenção preventiva dos equipamentos de perfuração e a constante formação dos operadores fazem parte de um conjunto de acções que irão determinar o sucesso da operação de perfuração, tendo sempre em vista, uma optimização técnico-económica, ou seja, produzir mais a um custo mais baixo. O estudo dos parâmetros do maciço rochoso aliado a uma perfuração cuidadosa e alinhada é evidenciado com o intuito de uma abordagem de geoengenharia integrada dos maciços rochosos. O estudo foi realizado na pedreira da APS, S.A. (Pedreira de Monte Chãos), tendo como análise os dados desde o início do projecto até à data. Para fundamentar este estudo, aborda-se os parâmetros geológico-geotécnicos e geomecânicos do maciço remanescente, verificando assim as ferramentas de corte mais adequadas ao caso e averiguar a influência da afiação de bits, quer seja manual ou semiautomática, e de que forma a mesma irá influenciar nos rendimentos e vidas úteis obtidas, tendo como objectivo, melhorar o custo por metro de furação realizado.

Avaliação ambiental sedimentar em área de perfuração exploratória marítima, bacia de campos, Rio de Janeiro-Brasil

Através do banco de dados referente a granulometria (cascalho, areia, silte e argila), carbonato biogênico, carbono orgânico total (COT) e argilo-minerais (caulinita, esmectita, ilita e gibsita) do projeto MAPEM- Monitoramento Ambiental em Atividades de Perfuração Exploratória Marítima (Águas Rasas), foi realizado este estudo visando avaliar os efeitos da perfuração dos poços BO-022H e BO-023H, localizados em talude continental superior, região sul da Bacia de Campos, Brasil, a 50 km da cidade de Cabo Frio, a 250m de profundidade. A promissora atividade de exploração e produção de petróleo e gás no Brasil tem exigido estudos detalhados do ambiente marinho, estes por sua vez deverão considerar desde a técnica de perfuração até a minuciosa alteração causada no substrato sedimentar. Nesta perspectiva foram coletadas amostras de sedimentos superficiais na região no em torno da área perfurada. Durante o cruzeiro I foram coletadas 48 amostras, no cruzeiro II, três meses após a perfuração, foram coletadas 61 amostras e no cruzeiro III, 22 meses após a perfuração, foram coletadas 54 amostras. Paralelamente foram amostradas 6 estações de controle. A preocupação é compreender quais são as alterações ambientas causadas pela perfuração, para isso as análises dos sedimentos geraram informações sobre a composição granulométrica, o teor carbonato biogênico e carbono orgânico total, e, composição mineralógica (argilo-minerais). Essas variáveis comparadas à variação espacial (área de monitoramento/estações de referência) e temporal (3 cruzeiros oceanográficos) permitiram compreender como o substrato sedimentar marinho reagiu a atividade de perfuração. Com o background da área, para os três cruzeiros oceanográficos, definiu-se os níveis médios das variáveis analisadas, identificando sinais de contaminação pela atividade de perfuração. Estes resultados demostram que a atividade de perfuração não promoveu alterações significativa nas propriedades sedimentares, que a variação dos valores de backgrounds, do cruzeiro II para o cruzeiro III, permaneceram muito próximo daqueles do cruzeiro I. Entre os argilo-minerais, a esmectita e a ilita , aumentaram, porém no cruzeiro III, os valores sofrem redução ficando muito próximo daqueles do cruzeiro I.

Enumeração de espectro de distâncias de esquemas de modulação codificada em treliça empregando codificação turbo

In this work, a performance analysis of transmission schemes employing turbo trellis coded modulation. In general, the performance analysis of such schemes is guided by evaluating the error probability of these schemes. The exact evaluation of this probability is very complex and inefficient from the computational point of view, a widely used alternative is the use of union bound of error probability, because of its easy implementation and computational produce bounds that converge quickly. Since it is the union bound, it should use to expurge some elements of distance spectrum to obtain a tight bound. The main contribution of this work is that the listing proposal is carried out from the puncturing at the level of symbol rather than bit-level as in most works of literature. The main reason for using the symbol level puncturing lies in the fact that the enummerating function of the turbo scheme is obtained directly from complex sequences of signals through the trellis and not indirectly from the binary sequences that require further binary to complex mapping, as proposed by previous works. Thus, algorithms can be applied through matrix from the adjacency matrix, which is obtained by calculating the distances of the complex sequences of the trellis. This work also presents two matrix algorithms for state reduction and the evaluation of the transfer function of this. The results presented in comparisons of the bounds obtained using the proposed technique with some turbo codes of the literature corroborate the proposition of this paper that the expurgated bounds obtained are quite tight and matrix algorithms are easily implemented in any programming software language

Fases de investigação geológico-geotécnica para a implantação de dutovias

The research addresses the need for detailed geological and geotechnical investigations in pipeline’s design, given the diversity of geological units crossed by these works along its layout, which often extends for hundreds of miles. For its large size, this type of work often goes through different states and regions with very different characteristics in terms of topography, vegetation, geology and geotechnical conditions. For a better use of these investigations in order to avoid unnecessary costs and inefficient results, some authors recommend that steps be taken to study, seeking a progressive detail of the pipeline’s implantation area. The main objective of the study is to describe, analyze and correlate the proposals for geological and geotechnical’s investigation recommended by the authors selected. Nogueira Junior & Marques (1998) suggest that for better effectiveness of geological and geotechnical investigations associated with the deployment of pipelines, different research methods are applied sequentially in five major stages of the building. Rocha et al (2008) recommend that, for the pipeline’s implantation using horizontal directional drilling, investigations are performed in three phases of study, to be developed in coordination with the project stages. For Gelinas & Mathy (2004), when time and budget constraints permit, geotechnical investigations for directional drilling projects for pipelines must be made in four sequential phases. Heinz (2008) suggests that the geotechnical investigations for pipeline’s implantation using horizontal directional drilling at crossings of water bodies are carried out in three successive stages. By the development of research, we could see that all the different proposals recommend studies in sequential phases, starting from a more general scale for a more specific, seeking a progressive understanding of the geological model of the area where you intend to deploy the pipeline

Efeito da geometria do implante dentário e do protocolo de fresagem óssea na estabilidade primária e na osseointegração inicial: estudo experimental em cães

CHAPTER 1 - This study histologically evaluated two implant designs: a classic thread design versus another specifically designed for healing chamber formation placed with two drilling protocols. Forty dental implants (4.1 mm diameter) with two different macrogeometries were inserted in the tibia of 10 Beagle dogs, and maximum insertion torque was recorded. Drilling techniques were: until 3.75 mm (regular-group); and until 4.0 mm diameter (overdrillinggroup) for both implant designs. At 2 and 4 weeks, samples were retrieved and processed for histomorphometric analysis. For torque and BIC (bone-to-implant contact) and BAFO (bone area fraction occupied), a general-linear model was employed including instrumentation technique and time in vivo as independent. The insertion torque recorded for each implant design and drilling group significantly decreased as a function of increasing drilling diameter for both implant designs (p<0.001). No significant differences were detected between implant designs for each drilling technique (p>0.18). A significant increase in BIC was observed from 2 to 4 weeks for both implants placed with the overdrilling technique (p<0.03) only, but not for those placed in the 3.75 mm drilling sites (p>0.32). Despite the differences between implant designs and drilling technique an intramembranous-like healing mode with newly formed woven bone prevailed. CHAPTER 2 - The objective of this preliminary histologic study was to determine whether the alteration of drilling protocols (oversized, intermediate, undersized drilling) present different biologic responses at early healing periods of 2 weeks in vivo in a beagle dog model. Ten beagle dogs were acquired and subjected to surgeries in the tibia 2 weeks before euthanasia. During surgery, 3 implants, 4 mm in diameter by 10 mm in length, were placed in bone sites drilled to 3.5 mm, 3.75 mm, and 4.0 mm in final diameter. The insertion and removal torque was recorded for all samples. Statistical significance was set to 95% level of confidence and the number of dogs was considered as the statistical unit for all comparisons. For the torque and BIC and BAFO, a general linear model was employed including instrumentation technique and time in vivo as independent. Overall, the insertion torque increased as a function of drilling diameter from 4.0 mm, to 3.75 mm, to 3.5 mm, with a significant difference in torque levels between all groups (p<0.001). Statistical assessment of BIC and BAFO showed significantly higher values for the 3.75 mm (recommended) drilling group was observed relative to the other two groups (p<0.001). Different drilling dimensions resulted in variations in insertion torque values (primary stability) and different pattern of healing and interfacial remodeling was observed for the different groups. CHAPTER 3 - The present study evaluated the effect of different drilling dimensions (undersized, regular, and oversized) in the insertion and removal torques of dental implants in a beagle dog model. Six beagle dogs were acquired and subjected to bilateral surgeries in the radii 1 and 3 weeks before euthanasia. During surgery, 3 implants, 4 mm in diameter by 10 mm in length, were placed in bone sites drilled to 3.2 mm, 3.5 mm, and 3.8 mm in final diameter. The insertion and removal torque was recorded for all samples. Statistical analysis was performed by paired t tests for repeated measures and by t tests assuming unequal variances (all at the 95% level of significance). Overall, the insertion torque and removal torque levels obtained were inversely proportional to the drilling dimension, with a significant difference detected between the 3.2 mm and 3.5 mm relative to the 3.8 mm groups (P < 0.03). Although insertion torque–removal torque paired observations was statis- tically maintained for the 3.5 mm and 3.8 mm groups, a significant decrease in removal torque values relative to insertion torque levels was observed for the 3.2 mm group. A different pattern of healing and interfacial remodeling was observed for the different groups. Different drilling dimensions resulted in variations in insertion torque values (primary stability) and stability maintenance over the first weeks of bone healing.

Constribuição técnica de um sistema de emulsão inversa a base de óleos vegetais para fluidos de perfuração

The developments in formulating drilling fluids to apply in petroleum fields are based on new technologies and environmental challenges, where the technical performance of a developed drilling fluid is used to produce a minimum environmental impact, showing great economy in costs. It is well known that the potential use of oil-based drilling fluids is limited because these fluids when discharged in the sea do not disperse as much as water-based ones and may form waterproof films in the seabed, having a profound effect on plants and animals living in this environment. The current works have been made in investigating fluids called pseudofluids, which are synthetic ester-based, n-paraffin-based and other fluids formed from inverse emulsion. In this research the principal parameters involved in inverse emulsion process were studied, in laboratory scale, using esters as main component. Others commercial drilling fluids were used as comparative samples, as well as samples from laboratory and field where these drilling fluids are being applied. Concentrations of emulsifier and organophilic clay, which are viscosity donor, were varied to verify the influence of these parameters, in different oil/water ratios (55/45, 60/40, 65/35, 70/30, and 75/25). The salt concentration (NaCl) is an indicative parameter of stability and activity of an esterbased fluid. In this research the salt concentration was varied in 10,000, 20,000, and 50,000 ppm of NaCl. Some rheological properties of the produced fluids were studied, such as: initial gel, plastic viscosity, yield point, and apparent viscosity. Through the obtained rheological measures, the existence of two systems could be verified: fluid and flocculated. It could be noticed that the systems were influenced, directly, by the oil/water ratio and emulsifier, organophilic clay and NaCl concentrations. This study showed the viability to use an ester obtained from a regional vegetable product babaçu coconut oil to obtain an efficient and environmental safe drilling fluid

A influência das características geomecânicas dos maciços fracturados no desvio da perfuração

A perfuração é uma das operações envolvidas no desmonte de rocha com explosivos. A forma como esta operação é executada é determinante para o sucesso do desmonte. Quando é realizada correctamente o desmonte produz superfícies limpas com o mínimo de sobrescavação e perturbação. A selecção das ferramentas de perfuração é um dos factores preponderantes para os custos do desmonte de maciços rochosos. A forma como a perfuração é executada é determinante para a boa fragmentação do maciço rochoso. Este estudo irá centrar‐se na perfurabilidade do maciço, linearidade dos furos e desenvolvimento de metodologias do ciclo de perfuração. O objectivo geral deste trabalho é demonstrar a interdependência entre os parâmetros geológicos e geotécnicos do maciço rochoso e as tecnologias de perfuração de forma a optimizar tanto técnica como economicamente. O controlo geomecânico do desmonte do maciço rochoso através de uma perfuração alinhada é salientado com o intuito de uma abordagem de geoengenharia integrada nos maciços rochosos.

Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour

Simulador de dano à formação, aplicado ao Projeto e à execução da perfuração de poços de petróleo

With the high oil price variability, the petroleum and the reservoir engineers are usually face to face on how they can evaluate the well performance and productivity. They can improve high productivity from the well construction to the secondary recoveries, but they have never tried a measurement in the drilling operations about the lower productivity index. As a rule, frequently the drilling operations hear from the reservoir engineering and geology that, if there is a formation damage, probably some drilling operations practices were not done properly or the good practice in petroleum engineering or mud engineering were not observed. The study in this working search is an attempt of how to measure a formation damage just from the project drilling to the drilling operations, with datum from the fields in Brazilian northeast and putting into practice a Simulator developed from the modeling on the theory offered by different experts and sources in formation damage

Nova técnica para obtenção de fraturas com altíssima condutividade em poços de petróleo

Increase hydrocarbons production is the main goal of the oilwell industry worldwide. Hydraulic fracturing is often applied to achieve this goal due to a combination of attractive aspects including easiness and low operational costs associated with fast and highly economical response. Conventional fracturing usually involves high-flowing high-pressure pumping of a viscous fluid responsible for opening the fracture in the hydrocarbon producing rock. The thickness of the fracture should be enough to assure the penetration of the particles of a solid proppant into the rock. The proppant is driven into the target formation by a carrier fluid. After pumping, all fluids are filtered through the faces of the fracture and penetrate the rock. The proppant remains in the fracture holding it open and assuring high hydraulic conductivity. The present study proposes a different approach for hydraulic fracturing. Fractures with infinity conductivity are formed and used to further improve the production of highly permeable formations as well as to produce long fractures in naturally fractured formations. Naturally open fractures with infinite conductivity are usually encountered. They can be observed in rock outcrops and core plugs, or noticed by the total loss of circulation during drilling (even with low density fluids), image profiles, pumping tests (Mini-Frac and Mini Fall Off), and injection tests below fracturing pressure, whose flow is higher than expected for radial Darcian ones. Naturally occurring fractures are kept open by randomly shaped and placed supporting points, able to hold the faces of the fracture separate even under typical closing pressures. The approach presented herein generates infinite conductivity canal held open by artificially created parallel supporting areas positioned both horizontally and vertically. The size of these areas is designed to hold the permeable zones open supported by the impermeable areas. The England & Green equation was used to theoretically prove that the fracture can be held open by such artificially created set of horizontal parallel supporting areas. To assess the benefits of fractures characterized by infinite conductivity, an overall comparison with finite conductivity fractures was carried out using a series of parameters including fracture pressure loss and dimensionless conductivity as a function of flow production, FOI folds of increase, flow production and cumulative production as a function of time, and finally plots of net present value and productivity index

Incorporação de resíduo de perfuração em matriz cerâmica: estabilização por solidificação

One of the waste generated during the drilling of oil wells are gravel which are impregnated of drilling fluid. This residue consists of highly toxic chemicals, including toxic metals. This study suggests an alternative process to the treatment of this waste, by incorporating it the form of raw material in the ceramic matrix , and by solidification and stabilize the metals present, Aluminum (Al), Iron (Fe), Manganese (Mn) and Zinc (Zn). The raw materials were characterized by the techniques of X ray fluorescence (FRX), X ray diffraction (DRX), laser granulometry (GL), thermogravimetry (TG) and differential thermal analysis (ADT). To evaluate the percentage of gravel effect the environmental and technological properties were obtained from formulations containing 0, 10 and 20 % by weight of gravel in the ceramic matrix. After sintering at temperatures 1080, 1120 and 1160 °C, the samples were tested for water absorption, the linear shrinkage firing, voltage of rupture and solubility. The results obtained showed that the stabilization by solidification, is a viable alternative to safe disposal of waste drilling. Ceramics products can be used in the manufacture of solid bricks

Desenvolvimento de misturas ternárias para remoção de reboco de fluido de perfuração sintético

The construction of wells is one of the most important activities of the oil industry. The drilling process is the set of activities and operations to design, program and perform the opening thereof. During this process, the cuttings are removed by the drilling fluid, or mud, and carted to the surface. This fluid is injected into the drill string and returns to the surface through the annular space between the well walls and the drill string. After the descent of the column casing, the annular space between the casing string and the walls of the borehole is filled with cement so as to secure the spine and prevent any migration of fluids between the various permeable zones traversed by the well behind of the coating. To ensure the good quality of the cementation scrubbers are used mattresses which are pumped ahead of the cement slurry so as to avoid contamination of the drilling fluid paste, or vice versa, and assist in the removal of plaster, formed by drilling fluid of the borehole walls, thus enabling a better cement bond to the well. Within this context, this work aims to evaluate the efficiency of mattresses scrubbers, the basis of ionic and nonionic surfactants, on the removal of nonaqueous drilling fluid, based on n-paraffin in oil wells, and the compatibility between the Mattress relations washer / drilling fluid bed scrubber / cement paste mattress washer / cement slurry / drilling fluid and the drilling fluid / cement slurry using laboratory tests rheology, thickening time and compressive strength. Also technique was performed X-ray diffraction (XRD) for a more detailed analysis of these mixtures with hydrated cement paste. In compatibility tests the conditions of temperature and pressure used in the same laboratory procedure simulating the conditions of oil wells, the well is considered the depth of 800 m. The results showed that the compositions of the mattress washer nonionic, KMS obtained a 100% efficient in removing the non-aqueous drilling fluid, and the best formulation showed good results with respect to compliance testing

Avaliação da resistência de união entre dentina preparada por laser e um sistema adesivo a base de silorano, variando a técnica de aplicação e umidade do substrato

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análises técnica e energética da secagem combinada no processamento de casulo do bicho-da-seda de Bombyx Mori L

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour