Experiments and modelling of phenanthrene biodegradation in the aqueous phase by a mixed culture

Pollution by polycyclic aromatic hydrocarbons(PAHs) is widespread due to unsuitable disposal of industrial waste. They are mostly defined as priority pollutants by environmental protection authorities worldwide. Phenanthrene, a typical PAH, was selected as the target in this paper. The PAH-degrading mixed culture, named ZM, was collected from a petroleum contaminated river bed. This culture was injected into phenanthrene solutions at different concentrations to quantify the biodegradation process. Results show near-complete removal of phenanthrene in three days of biodegradation if the initial phenanthrene concentration is low. When the initial concentration is high, the removal rate is increased but 20%-40% of the phenanthrene remains at the end of the experiment. The biomass shows a peak on the third day due to the combined effects of microbial growth and decay. Another peak is evident for cases with a high initial concentration, possibly due to production of an intermediate metabolite. The pH generally decreased during biodegradation because of the production of organic acid. Two phenomenological models were designed to simulate the phenanthrene biodegradation and biomass growth. A relatively simple model that does not consider the intermediate metabolite and its inhibition of phenanthrene biodegradation cannot fit the observed data. A modified Monod model that considered an intermediate metabolite (organic acid) and its inhibiting reversal effect reasonably depicts the experimental results.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Avaliação cinética da produção de biossurfactantes bacterianos

Biosurfactants present advantages in relation to the synthetic surfactants, as the biodegradability and low toxicity, and can be applied in the food industry, in pharmaceutical products, cosmetics and in the petroleum recovery. This paper aimed at selecting bacteria for biosurfactant production, evaluating the surface tension and the emulsifying activity and studying the fermentation process kinetics. The pure culture of Corynebacterium aquaticum showed capacity to promote emulsions formation and presented the smallest surface tension (28.8 mN m-1), and, in general, larger kinetic parameters, being selected as biosurfactant producer.

Foam-forming properties of Ilex paraguariensis (mate) saponin: foamability and foam lifetime analysis by Weibull equation

Saponins are natural soaplike foam-forming compounds widely used in foods, cosmetic and pharmaceutical preparations. In this work foamability and foam lifetime of foams obtained from Ilex paraguariensis unripe fruits were analyzed. Polysorbate 80 and sodium dodecyl sulfate were used as reference surfactants. Aiming a better data understanding a linearized 4-parameters Weibull function was proposed. The mate hydroethanolic extract (ME) and a mate saponin enriched fraction (MSF) afforded foamability and foam lifetime comparable to the synthetic surfactants. The linearization of the Weibull equation allowed the statistical comparison of foam decay curves, improving former mathematical approaches.

A influência dos elementos traços , (B, Cu, Mn, Mo e Zn) na produção de ramnolipídios por pseudomonas aeruginosa LBI

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Investigação dos efeitos tóxicos do biossurfactante ramnolipídio e suas implicações quando usado na biorremediação de águas contaminadas por petróleo

Pós-graduação em Ciências Biológicas (Biologia Celular e Molecular) - IBRC

Bactérias produtoras de biossurfactantes: isolamento, produção, caracterização e comportamento num sistema modelo

Pós-graduação em Engenharia e Ciência de Alimentos - IBILCE

Produção de ramnolipídios por mutantes de Pseudomonas aeruginosa LBI

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of the pre-inoculum utilization in biosurfactant production by solid-state fermentation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Bioremediation of PAHs - Limitations and soultions

Introduction 1.1 Occurrence of polycyclic aromatic hydrocarbons (PAH) in the environment Worldwide industrial and agricultural developments have released a large number of natural and synthetic hazardous compounds into the environment due to careless waste disposal, illegal waste dumping and accidental spills. As a result, there are numerous sites in the world that require cleanup of soils and groundwater. Polycyclic aromatic hydrocarbons (PAHs) are one of the major groups of these contaminants (Da Silva et al., 2003). PAHs constitute a diverse class of organic compounds consisting of two or more aromatic rings with various structural configurations (Prabhu and Phale, 2003). Being a derivative of benzene, PAHs are thermodynamically stable. In addition, these chemicals tend to adhere to particle surfaces, such as soils, because of their low water solubility and strong hydrophobicity, and this results in greater persistence under natural conditions. This persistence coupled with their potential carcinogenicity makes PAHs problematic environmental contaminants (Cerniglia, 1992; Sutherland, 1992). PAHs are widely found in high concentrations at many industrial sites, particularly those associated with petroleum, gas production and wood preserving industries (Wilson and Jones, 1993). 1.2 Remediation technologies Conventional techniques used for the remediation of soil polluted with organic contaminants include excavation of the contaminated soil and disposal to a landfill or capping - containment - of the contaminated areas of a site. These methods have some drawbacks. The first method simply moves the contamination elsewhere and may create significant risks in the excavation, handling and transport of hazardous material. Additionally, it is very difficult and increasingly expensive to find new landfill sites for the final disposal of the material. The cap and containment method is only an interim solution since the contamination remains on site, requiring monitoring and maintenance of the isolation barriers long into the future, with all the associated costs and potential liability. A better approach than these traditional methods is to completely destroy the pollutants, if possible, or transform them into harmless substances. Some technologies that have been used are high-temperature incineration and various types of chemical decomposition (for example, base-catalyzed dechlorination, UV oxidation). However, these methods have significant disadvantages, principally their technological complexity, high cost , and the lack of public acceptance. Bioremediation, on the contrast, is a promising option for the complete removal and destruction of contaminants. 1.3 Bioremediation of PAH contaminated soil & groundwater Bioremediation is the use of living organisms, primarily microorganisms, to degrade or detoxify hazardous wastes into harmless substances such as carbon dioxide, water and cell biomass Most PAHs are biodegradable unter natural conditions (Da Silva et al., 2003; Meysami and Baheri, 2003) and bioremediation for cleanup of PAH wastes has been extensively studied at both laboratory and commercial levels- It has been implemented at a number of contaminated sites, including the cleanup of the Exxon Valdez oil spill in Prince William Sound, Alaska in 1989, the Mega Borg spill off the Texas coast in 1990 and the Burgan Oil Field, Kuwait in 1994 (Purwaningsih, 2002). Different strategies for PAH bioremediation, such as in situ , ex situ or on site bioremediation were developed in recent years. In situ bioremediation is a technique that is applied to soil and groundwater at the site without removing the contaminated soil or groundwater, based on the provision of optimum conditions for microbiological contaminant breakdown.. Ex situ bioremediation of PAHs, on the other hand, is a technique applied to soil and groundwater which has been removed from the site via excavation (soil) or pumping (water). Hazardous contaminants are converted in controlled bioreactors into harmless compounds in an efficient manner. 1.4 Bioavailability of PAH in the subsurface Frequently, PAH contamination in the environment is occurs as contaminants that are sorbed onto soilparticles rather than in phase (NAPL, non aqueous phase liquids). It is known that the biodegradation rate of most PAHs sorbed onto soil is far lower than rates measured in solution cultures of microorganisms with pure solid pollutants (Alexander and Scow, 1989; Hamaker, 1972). It is generally believed that only that fraction of PAHs dissolved in the solution can be metabolized by microorganisms in soil. The amount of contaminant that can be readily taken up and degraded by microorganisms is defined as bioavailability (Bosma et al., 1997; Maier, 2000). Two phenomena have been suggested to cause the low bioavailability of PAHs in soil (Danielsson, 2000). The first one is strong adsorption of the contaminants to the soil constituents which then leads to very slow release rates of contaminants to the aqueous phase. Sorption is often well correlated with soil organic matter content (Means, 1980) and significantly reduces biodegradation (Manilal and Alexander, 1991). The second phenomenon is slow mass transfer of pollutants, such as pore diffusion in the soil aggregates or diffusion in the organic matter in the soil. The complex set of these physical, chemical and biological processes is schematically illustrated in Figure 1. As shown in Figure 1, biodegradation processes are taking place in the soil solution while diffusion processes occur in the narrow pores in and between soil aggregates (Danielsson, 2000). Seemingly contradictory studies can be found in the literature that indicate the rate and final extent of metabolism may be either lower or higher for sorbed PAHs by soil than those for pure PAHs (Van Loosdrecht et al., 1990). These contrasting results demonstrate that the bioavailability of organic contaminants sorbed onto soil is far from being well understood. Besides bioavailability, there are several other factors influencing the rate and extent of biodegradation of PAHs in soil including microbial population characteristics, physical and chemical properties of PAHs and environmental factors (temperature, moisture, pH, degree of contamination). Figure 1: Schematic diagram showing possible rate-limiting processes during bioremediation of hydrophobic organic contaminants in a contaminated soil-water system (not to scale) (Danielsson, 2000). 1.5 Increasing the bioavailability of PAH in soil Attempts to improve the biodegradation of PAHs in soil by increasing their bioavailability include the use of surfactants , solvents or solubility enhancers.. However, introduction of synthetic surfactant may result in the addition of one more pollutant. (Wang and Brusseau, 1993).A study conducted by Mulder et al. showed that the introduction of hydropropyl-ß-cyclodextrin (HPCD), a well-known PAH solubility enhancer, significantly increased the solubilization of PAHs although it did not improve the biodegradation rate of PAHs (Mulder et al., 1998), indicating that further research is required in order to develop a feasible and efficient remediation method. Enhancing the extent of PAHs mass transfer from the soil phase to the liquid might prove an efficient and environmentally low-risk alternative way of addressing the problem of slow PAH biodegradation in soil.

Assessment of the potential skin irritation of lysine-derivative anionic surfactants using mouse fibroblast and human keratinocytes as an alternative to animal testing

Purpose. The aim of this study was to identify new surfactants with low skin irritant properties for use in pharmaceutical and cosmetic formulations, employing cell culture as an alternative method to in vivo testing. In addition, we sought to establish whether potential cytotoxic properties were related to the size of the counterions bound to the surfactants. Methods. Cytotoxicity was assessed in the mouse fibroblast cell line 3T6, and the human keratinocyte cell line NCTC 2544, using the MTT assay and uptake of the vital dye neutral red 24 h after dosing (NRU). Results. Lysine-derivative surfactants showed higher IC50s than did commercial anionic irritant compounds such as sodium dodecyl sulphate, proving to be no more harmful than amphoteric betaines. The aggressiveness of the surfactants depended upon the size of their constituent counterions: surfactants associated with lighter counterions showed a proportionally higher aggressivity than those with heavier ones. Conclusions. Synthetic lysine-derivative anionic surfactants are less irritant than commercial surfactants such as sodium dodecyl sulphate and Hexadecyltrimethylammonium bromide and are similar to Betaines. These surfactants may offer promising applications in pharmaceutical and cosmetic preparations, representing a potential alternative to commercial anionic surfactants as a result of their low irritancy potential.

Noves aproximacions a la síntesi i caracterització de poliglicols al·lílics, polihidrosiloxans i surfactants copolimèrics. Avaluació d'aquests surfactants en formulacions de poliuretà

Els polímers són una sèrie de compostos que troben un ampli ventall d'aplicacions en la indústria actual. Un exemple són les espumes de poliuretà, estructures de tipus cel·lular obtingudes mitjançant la reacció química entre compostos de tipus isocianat i compostos de tipus poliol (polièters amb diferent nombre de grups hidroxil). És imprescindible l'ús d'additius d'estructura tensioactiva (surfactants de silicona) per estabilitzar el procés d'espumació i per proporcionar una estructura cel·lular ordenada i homogènia en mida i distribució. La síntesis i caracterització de les molècules precursores (polihidrosiloxans i polièters al·lílics), l'estudi de la reacció d'hidrosililació com a via d'obtenció dels diferents surfactants per reacció d'addició entre els polihidrosiloxans i els polièters al·lílics i la caracterització i avaluació en formulacions comercials de poliuretà dels surfactants sintetitzats han constituït els objectius del present treball. MEMÒRIA La Tesi Doctoral ha estat presentada seguint el següent esquema: CAPÍTOL I. INTRODUCCIÓ A LA QUÍMICA DEL POLIURETÀ. Es presenten els principis de la química del poliuretà, fent esment dels recents avenços en la síntesis i caracterització d'aquests compostos polimèrics, així com un apartat concret centrat en els surfactants de silicona. Es presenten les estructures habituals d'aquests compostos comercials i es detallen les reaccions de síntesi i les característiques físiques que aquests compostos proporcionen a les espumes de poliuretà. CAPÍTOL II. OBJECTIUS. 1.- Síntesis y caracterització d'una àmplia gamma de poliglicols al·lílics i de polihidrosiloxans amb grups hidrur reactius, ambdós precursors d'estructures polimèriques de tipus surfactant. 2.- Estudi de la reacció d'hidrosililació com a via de formació d'enllaços Si-C no hidrolitzables, mitjançant la reacció d'addició entre els substrats al·lílics insaturats i els polisiloxans amb grups hidrur reactius. 3.- Caracterització de les estructures polimèriques de tipus surfactant sintetitzades i avaluació d'aquestes en formulacions de poliuretà, a fi de relacionar l'estructura química d'aquests oligómers amb els efectes físics que originen en l'espuma de poliuretà. CAPÍTOL III. SÍNTESI I CARACTERITZACIÓ DE SUBSTRATS AL·LÍLICS INSATURATS DE TIPUS POLIGLICOL. S'han caracteritzat per HPLC-UV una sèrie de polietilenglicols comercials. S'ha estudiat la reacció de derivatització al·lílica sobre els grups hidroxil dels polièters comercials (PEG, PPG i copolímers PEG-PPG) i s'han caracteritzat exhaustivament els productes sintetitzats (1H,13C-RMN, GC, GC-MS, FTIR, ESI-MS, HPLC-UV). S'ha iniciat un estudi de polimerització aniònica sobre nous epòxids amb un punt de diversitat molecular, sintetitzant-se i caracteritzant-se els corresponents nous polièters obtinguts. CAPÍTOL IV. SÍNTESI I CARACTERITZACIÓ DE POLIHIDROSILOXANS REACTIUS. S'estudia la síntesis de polihidrosiloxans amb grups hidrur reactius, mitjançant la reacció de polimerització aniònica d'obertura d'anell ("AROP, anionic ring opening polimerization") i mitjançant la reacció de polimerització per equilibració catiònica. Es presenta una caracterització exhaustiva dels productes sintetitzats i es descriu la naturalesa de la microestructura polimèrica a partir de la distribució bivariant dels copolímers PDMS-co-PHMS (poli(dimetilsiloxà)-co-poli(hidrometilsiloxà)). CAPÍTOL V. ESTUDI SISTEMÀTIC DE LA REACCIÓ D'HIDROSILILACIÓ. S'ha estudiat la reacció d'hidrosililació amb la finalitat de sintetitzar estructures copolimèriques poliglicol-polisiloxà a partir de la reacció de polisiloxans hidrur reactius i polièters al·lílics. S'han provat diferents catalitzadors (Pt/C 5%, cat. de Speier i cat. de Karstedt), s'han sintetitzat diferents estructures tensoactives (lineals i ramificades) i s'ha modelitzat les diferents reaccions secundàries observades, per presentar un estudi mecanístic de la reacció d'hidrosililació aplicada a la síntesis de molècules d'elevat PM a partir de la reacció entre substrats al·lílics insaturats i polihidrosiloxans. CAPÍTOL VI. AVALUACIÓ DELS SURFACTANTS EN FORMULACIONS DE POLIURETÀ. S'ha estudiat la idoneïtat dels surfactants de silicona sintetitzats en diferents formulacions de poliuretà comercials. S'ha relacionat el comportament físic d'aquests surfactants en les espumes de poliuretà amb la seva estructura química a partir de l'anàlisi per microscòpia electrònica de rastreig. CAPÍTOL VII. CONCLUSIONS. S'han esposat les conclusions extretes de cada capítol.

Novel tear film supplements:a potential application for synthetic protein-phospholipid complexes

Purpose: Surfactant proteins A, B, C and D complex with (phospho)lipids to produce surfactants which provide low interfacial tensions. It is likely that similar complexation occurs in the tear film and contributes to its low surface tension. Synthetic protein-phospholipid complexes, with styrene maleic anhydrides (SMAs) as the protein analogue, have been shown to have similarly low surface tensions. This study investigates the potential of modified SMAs and/or SMA-phospholipid complexes, which form under physiological conditions, to supplement natural tear film surfactants. Method: SMAs were modified to provide structural variants which can form complexes under varying conditions. Infrared spectroscopy and Nuclear Magnetic Resonance were used to confirm SMA structure. Interfacial behaviour of the SMA and SMA-phospholipid complexes was studied using Langmuir trough, du Nûoy ring and pulsating bubblemethods. Factors which affect SMA-phospholipid complex formation, such as temperature and pH, were also investigated. Results: Structural manipulation of SMAs allows control over complex formation, including under physiological conditions (e.g. partial SMAesterfication allowed complexation with dimyristoylphosphatidylcholine, at pH7). The low surface tensions of the SMAs (42mN/m for static (du Nûoy ring) and 34mN/m for dynamic (Langmuir) techniques) demonstrate their surface activity at the air-aqueous interface. SMA-phospholipid complexes provide even lower surface tensions (~2 mN/m), approaching that of lung surfactant, as measured by the pulsating bubblemethod. Conclusions: Design of the molecular architecture of SMAs allows control over their surfactant properties. These SMAs could be used as novel tear films supplements, either alone to complex with native tear film phospholipids or delivered as synthetic protein-phospholipid complexes.

Biomimetic synthetic lubricants (Biosurfactants)

Poly(styrene-co-maleic anhydride) (PSMA) based copolymers are known to undergo conformational transition in response to environmental stimuli. This smart behaviour makes it possible to mimic the behaviour of native apoproteins. The primary aim of this study was to develop a better understanding of the structure-property relationships of various PSMA-based copolymers sought. The work undertaken in this thesis has revealed that the responsive behaviour of PSMA-based copolymers can be tailored by varying the molecular weight, hydrophobic (styrene) and hydrophilic (maleic acid) balance, and more so in the presence of additional hydrophobic, mono-partial ester moieties. Novel hydrophilic and hydrophobic synthetic surfactant protein analogues have successfully been prepared. These novel lipid solubilising agents possess a broad range of HLB (hydrophilic-lipophilic balance) values that have been estimated. NMR spectroscopy was utilised to confirm the structures for PSMA-based copolymers sought and proved useful in furthering understanding of the structure-property relationships of PSMA-based copolymers. The association of PSMA with the polar phospholipid, 2-dilauryl-sn-glycero-3- phosphocholine (DLPC) produces polymer-lipid complexes analogous to lipoprotein assemblies present in the blood plasma. NMR analysis reveals that the PSMA-based copolymers are not perfectly alternating. Regio-irregular structures, atactic and random monomer sequence distribution have been identified for all materials studied. Novel lipid solubilising agents (polyanionic surfactants) have successfully been synthesised from a broad range of PSMA-based copolymers with desired estimated HLB values that interact with polar phospholipids (DLPC/DPPC) uniquely. Very low static and dynamic surface tensions have been observed via the du Noϋy ring method and Langmuir techniques and correlate well with the estimated HLB values. Synthetic protein-lipid analogues have been successfully synthesised, that mimic the unique surface properties of native biological lubricants without the use of solvents. The novel PSMA-DLPC complexes have successfully been combined with hyaluronan (hyaluronic acid, HA). Today, the employment of HA is economically feasible, because it is readily available from bacterial fermentation processes in a thermally stable form - HyaCare®. The work undertaken in this thesis highlights the usage of HA in biolubrication applications and how this can be optimised and thus justified by carefully selecting the biological source, concentration, molecular weight, purity and most importantly by combining it with compatible boundary lubricating agents (polar phospholipids). Experimental evidence supports the belief that the combined HA and PSMA-DLPC complexes provide a balance of rheological, biotribological and surface properties that are composition dependent, and show competitive advantage as novel synthetic biological lubricants (biosurfactants).