General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Investigations on Metamaterial Based Spiral Inductors for Compact Microwave Devices

Division of Electronics Engineering

Non-linear modelling of microwave devices embedding nano-ferroelectric materials for real-time reconfigurable transmitarray

In this thesis work a nonlinear model for Interdigitated Capacitors (IDCs) based on ferroelectric materials, is proposed. Through the properties of materials such as Hafnium-Zirconium Oxide (HfZrO2), it is possible to realize tunable radiofrequency (RF) circuits. In particular, the model proposed in this thesis describes the use of an IDC, realized on a High-Resistivity silicon substrate, as a phase shifter for beam-steering applications. The model is obtained starting from already present experimental measurements, through which it is possible to identify a circuit model. The model is tested for both low power values and other power values using Harmonic Balance simulations, which show an excellent convergence of the model up to 40 dBm of input power. Furthermore, an array composed by two patches operating both at 2.55 GHz, which exploits the tunable properties of the HfZrO-based IDC is proposed. At 0dBm the model shows a 47° phase shift with polarization -1 V and 1 V which leads to a 11° steering of the main lobe of the array.

Sintering temperature influence on microwave dielectric properties of TiO2-ZrO2 ceramics

Dielectric ceramics have been widely investigated and used for microwave applications such as resonators and filters. The present study deals with the influence of sintering temperature on microwave dielectric properties of TiO2 ceramics with 10, 20, and 30 wt% ZrO2. Three compositions have been developed through mixing procedures and then tested for each sintering temperature: 1500 and 1400°C. X-ray diffraction and scanning electron microscopy are carried out aiming to explain the ceramic behavior of each sample. The dielectric constants of different ceramics for both temperatures varied from 85.4 to 62.6, while their quality factor due to dielectric losses varied from 3110 to 1630. The Q decrease is attributed to the non uniform grain growth and to the obtained crystalline phases. The best microwave parameters were obtained for the ceramics sintered at 1400°C, which can be applied in microwave circuits as dielectric resonators. © (2010) Trans Tech Publications.

Sintering and Microwave Properties of Zirconium Tin Titanate Doped with Select Oxides

Zirconium tin titanate (ZST) is often used as a dielectric resonator for the fabrication of microwave devices. Pure compositions do not sinter easily by solid state sintering; therefore, sintering ZST requires sintering aids capable of creating defects that could improve diffusion processes and/or promote liquid phase sintering. The mechanisms by which the additives influence the microstructure and, consequently, the ZSTs dielectric properties are not very clear. The effects of ZnO, Bi2O3, and La2O3, on the stoichiometry and dielectric properties of ZST sintered at different temperatures were investigated in this study.

Nuevas arquitecturas de transpondedores de microondas = New transponder architectures at microwave frequencies = Nouvelles architectures des transpondeurs d’hyperfréquences

En la última década, los sistemas de telecomunicación de alta frecuencia han evolucionado tremendamente. Las bandas de frecuencias, los anchos de banda del usuario, las técnicas de modulación y otras características eléctricas están en constante cambio de acuerdo a la evolución de la tecnología y la aparición de nuevas aplicaciones. Las arquitecturas de los transceptores modernos son diferentes de las tradicionales. Muchas de las funciones convencionalmente realizadas por circuitos analógicos han sido asignadas gradualmente a procesadores digitales de señal, de esta manera, las fronteras entre la banda base y las funcionalidades de RF se difuminan. Además, los transceptores inalámbricos digitales modernos son capaces de soportar protocolos de datos de alta velocidad, por lo que emplean una elevada escala de integración para muchos de los subsistemas que componen las diferentes etapas. Uno de los objetivos de este trabajo de investigación es realizar un estudio de las nuevas configuraciones en el desarrollo de demostradores de radiofrecuencia (un receptor y un transmisor) y transpondedores para fines de comunicaciones y militares, respectivamente. Algunos trabajos se han llevado a cabo en el marco del proyecto TECRAIL, donde se ha implementado un demostrador de la capa física LTE para evaluar la viabilidad del estándar LTE en el entorno ferroviario. En el ámbito militar y asociado al proyecto de calibración de radares (CALRADAR), se ha efectuado una actividad importante en el campo de la calibración de radares balísticos Doppler donde se ha analizado cuidadosamente su precisión y se ha desarrollado la unidad generadora de Doppler de un patrón electrónico para la calibración de estos radares. Dicha unidad Doppler es la responsable de la elevada resolución en frecuencia del generador de “blancos” radar construido. Por otro lado, se ha elaborado un análisis completo de las incertidumbres del sistema para optimizar el proceso de calibración. En una segunda fase se han propuesto soluciones en el desarrollo de dispositivos electro-ópticos para aplicaciones de comunicaciones. Estos dispositivos son considerados, debido a sus ventajas, tecnologías de soporte para futuros dispositivos y subsistemas de RF/microondas. Algunas demandas de radio definida por software podrían cubrirse aplicando nuevos conceptos de circuitos sintonizables mediante parámetros programables de un modo dinámico. También se ha realizado una contribución relacionada con el diseño de filtros paso banda con topología “Hairpin”, los cuales son compactos y se pueden integrar fácilmente en circuitos de microondas en una amplia gama de aplicaciones destinadas a las comunicaciones y a los sistemas militares. Como importante aportación final, se ha presentado una propuesta para ecualizar y mejorar las transmisiones de señales discretas de temporización entre los TRMs y otras unidades de procesamiento, en el satélite de última generación SEOSAR/PAZ. Tras un análisis exhaustivo, se ha obtenido la configuración óptima de los buses de transmisión de datos de alta velocidad basadas en una red de transceptores. ABSTRACT In the last decade, high-frequency telecommunications systems have extremely evolved. Frequency bands, user bandwidths, modulation techniques and other electrical characteristics of these systems are constantly changing following to the evolution of technology and the emergence of new applications. The architectures of modern transceivers are different from the traditional ones. Many of the functions conventionally performed by analog circuitry have gradually been assigned to digital signal processors. In this way, boundaries between baseband and RF functionalities are diffused. The design of modern digital wireless transceivers are capable of supporting high-speed data protocols. Therefore, a high integration scale is required for many of the components in the block chain. One of the goals of this research work is to investigate new configurations in the development of RF demonstrators (a receiver and a transmitter) and transponders for communications and military purposes, respectively. A LTE physical layer demonstrator has been implemented to assess the viability of LTE in railway scenario under the framework of the TECRAIL project. An important activity, related to the CALRADAR project, for the calibration of Doppler radars with extremely high precision has been performed. The contribution is the Doppler unit of the radar target generator developed that reveals a high frequency resolution. In order to assure the accuracy of radar calibration process, a complete analysis of the uncertainty in the above mentioned procedure has been carried out. Another important research topic has been the development of photonic devices that are considered enabling technologies for future RF and microwave devices and subsystems. Some Software Defined Radio demands are addressed by the proposed novel circuit concepts based on photonically tunable elements with dynamically programmable parameters. A small contribution has been made in the field of Hairpin-line bandpass filters. These filters are compact and can also be easily integrated into microwave circuits finding a wide range of applications in communication and military systems. In this research field, the contributions made have been the improvements in the design and the simulations of wideband filters. Finally, an important proposal to balance and enhance transmissions of discrete timing signals between TRMs and other processing units into the state of the art SEOSAR/PAZ Satellite has been carried out obtaining the optimal configuration of the high-speed data transmission buses based on a transceiver network. RÉSUMÉ Les systèmes d'hyperfréquence dédiés aux télécommunications ont beaucoup évolué dans la dernière décennie. Les bandes de fréquences, les bandes passantes par utilisateur, les techniques de modulation et d'autres caractéristiques électriques sont en constant changement en fonction de l'évolution des technologies et l'émergence de nouvelles applications. Les architectures modernes des transcepteurs sont différentes des traditionnelles. Un grand nombre d’opérations normalement effectuées par les circuits analogiques a été progressivement alloué à des processeurs de signaux numériques. Ainsi, les frontières entre la bande de base et la fonctionnalité RF sont floues. Les transcepteurs sans fils numériques modernes sont capables de transférer des données à haute vitesse selon les différents protocoles de communication utilisés. C'est pour cette raison qu’un niveau élevé d'intégration est nécessaire pour un grand nombre de composants qui constitue les différentes étapes des systèmes. L'un des objectifs de cette recherche est d'étudier les nouvelles configurations dans le développement des démonstrateurs RF (récepteur et émetteur) et des transpondeurs à des fins militaire et de communication. Certains travaux ont été réalisés dans le cadre du projet TECRAIL, où un démonstrateur de la couche physique LTE a été mis en place pour évaluer la faisabilité de la norme LTE dans l'environnement ferroviaire. Une contribution importante, liée au projet CALRADAR, est proposée dans le domaine des systèmes d’étalonnage de radar Doppler de haute précision. Cette contribution est le module Doppler de génération d’hyperfréquence intégré dans le système électronique de génération de cibles radar virtuelles que présente une résolution de fréquence très élevée. Une analyse complète de l'incertitude dans l'étalonnage des radars Doppler a été effectuée, afin d'assurer la précision du calibrage. La conception et la mise en oeuvre de quelques dispositifs photoniques sont un autre sujet important du travail de recherche présenté dans cette thèse. De tels dispositifs sont considérés comme étant des technologies habilitantes clés pour les futurs dispositifs et sous-systèmes RF et micro-ondes grâce à leurs avantages. Certaines demandes de radio définies par logiciel pourraient être supportées par nouveaux concepts de circuits basés sur des éléments dynamiquement programmables en utilisant des paramètres ajustables. Une petite contribution a été apportée pour améliorer la conception et les simulations des filtres passe-bande Hairpin à large bande. Ces filtres sont compacts et peuvent également être intégrés dans des circuits à micro-ondes compatibles avec un large éventail d'applications dans les systèmes militaires et de communication. Finalement, une proposition a été effectuée visant à équilibrer et améliorer la transmission des signaux discrets de synchronisation entre les TRMs et d'autres unités de traitement dans le satellite SEOSAR/PAZ de dernière génération et permettant l’obtention de la configuration optimale des bus de transmission de données à grande vitesse basés sur un réseau de transcepteurs.

Investigation of an optically reconfigurable plasma for silicon based microwave applications

This paper investigates the use of photoconductive plasmas for controlling microwave circuits and antennas on semiconductor substrates. Initial experiments show that significant changes in the reflection coefficient characteristics can be obtained by varying the length of a photo-illuminated plasma region from 0 to 2mm. The resulting structure forms the basis for further experiments involving tuneable microwave devices. © 2013 European Microwave Association.

Diseño de inversores de impedancias de microondas compactos basados en metamateriales: aplicación a divisores de potencia

Recientemente ha surgido un nuevo campo de investigación en el área del electromagnetismo aplicado y de la ingeniería de microondas, basado en el control de las propiedades electromagnéticas de estructuras artificiales, conocidas como metamateriales. El objetivo principal de este proyecto es el estudio y control del comportamiento de estas estructuras artificiales, y su posterior aplicación para la síntesis de dispositivos compactos de microondas. En el primer capítulo se hace una introducción a los metamateriales en la que se exponen sus principales propiedades electromagnéticas, para finalmente presentar las líneas de transmisión zurdas que se suelen utilizar en el diseño de metamateriales. En el segundo capítulo se realiza un estudio de las propiedades y del funcionamiento de una celda metamaterial. Finalmente en el tercer capítulo se exponen diferentes dispositivos diseñados mediante la utilización de este tipo de celdas.

Dispersion of Hybrid Electromagnetic-Spin Waves in the Slotline

The presented thesis is devoted to investigation of wave processes in hybrid ferrite / ferroelectric structures. Spin wave devices based on ferrite films have such disadvantages, as huge size of the magnetic systems, low tuning velocity, considerable power inputs for parameters control that limits possible device applications. The considered layered structures allow to overcome the disadvantages mentioned and to promote the development of novel class of tunable microwave devices. The proposed theoretical analysis is intended to construct a model of hybrid electromagnetic-spin waves. Based on the theoretical analysis the experimental investigations were carried out. The experimental resonance characteristics of ferrite / ferroelectric resonator were obtained and their tunability by means of magnetic and electric field was demonstrated.

APSYM 2014

14th Biennial International Symposium on Antennas and propagation Department of Electronics, Cochin University of Science & Technology, Cochin 682022, INDIA

Análise e projeto de superfícies seletivas de frequência com elementos pré-fractais para aplicações em comunicações indoor

In this thesis, a frequency selective surface (FSS) consists of a two-dimensional periodic structure mounted on a dielectric substrate, which is capable of selecting signals in one or more frequency bands of interest. In search of better performance, more compact dimensions, low cost manufacturing, among other characteristics, these periodic structures have been continually optimized over time. Due to its spectral characteristics, which are similar to band-stop or band-pass filters, the FSSs have been studied and used in several applications for more than four decades. The design of an FSS with a periodic structure composed by pre-fractal elements facilitates the tuning of these spatial filters and the adjustment of its electromagnetic parameters, enabling a compact design which generally has a stable frequency response and superior performance relative to its euclidean counterpart. The unique properties of geometric fractals have shown to be useful, mainly in the production of antennas and frequency selective surfaces, enabling innovative solutions and commercial applications in microwave range. In recent applications, the FSSs modify the indoor propagation environments (emerging concept called wireless building ). In this context, the use of pre-fractal elements has also shown promising results, allowing a more effective filtering of more than one frequency band with a single-layer structure. This thesis approaches the design of FSSs using pre-fractal elements based on Vicsek, Peano and teragons geometries, which act as band-stop spatial filters. The transmission properties of the periodic surfaces are analyzed to design compact and efficient devices with stable frequency responses, applicable to microwave frequency range and suitable for use in indoor communications. The results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as: fractal iteration number (or fractal level), scale factor, fractal dimension and periodicity of FSS, according the pre-fractal element applied on the surface. The analysis of the fractal dimension s influence on the resonant properties of a FSS is a new contribution in relation to researches about microwave devices that use fractal geometry. Due to its own characteristics and the geometric shape of the Peano pre-fractal elements, the reconfiguration possibility of these structures is also investigated and discussed. This thesis also approaches, the construction of efficient selective filters with new configurations of teragons pre-fractal patches, proposed to control the WLAN coverage in indoor environments by rejecting the signals in the bands of 2.4~2.5 GHz (IEEE 802.11 b) and 5.0~6.0 GHz (IEEE 802.11a). The FSSs are initially analyzed through simulations performed by commercial software s: Ansoft DesignerTM and HFSSTM. The fractal design methodology is validated by experimental characterization of the built prototypes, using alternatively, different measurement setups, with commercial horn antennas and microstrip monopoles fabricated for low cost measurements

Modelos de dispositivos de microondas e ópticos através de redes neurais artificiais de alimentação direta

This dissertation contributes for the development of methodologies through feed forward artificial neural networks for microwave and optical devices modeling. A bibliographical revision on the applications of neuro-computational techniques in the areas of microwave/optical engineering was carried through. Characteristics of networks MLP, RBF and SFNN, as well as the strategies of supervised learning had been presented. Adjustment expressions of the networks free parameters above cited had been deduced from the gradient method. Conventional method EM-ANN was applied in the modeling of microwave passive devices and optical amplifiers. For this, they had been proposals modular configurations based in networks SFNN and RBF/MLP objectifying a bigger capacity of models generalization. As for the training of the used networks, the Rprop algorithm was applied. All the algorithms used in the attainment of the models of this dissertation had been implemented in Matlab

Modelagem de Superfícies Seletivas de Freqüência e Antenas de Microfita utilizando Redes Neurais Artificiais

This work has as main objective the application of Artificial Neural Networks, ANN, in the resolution of problems of RF /microwaves devices, as for example the prediction of the frequency response of some structures in an interest region. Artificial Neural Networks, are presently a alternative to the current methods of analysis of microwaves structures. Therefore they are capable to learn, and the more important to generalize the acquired knowledge, from any type of available data, keeping the precision of the original technique and adding the low computational cost of the neural models. For this reason, artificial neural networks are being increasily used for modeling microwaves devices. Multilayer Perceptron and Radial Base Functions models are used in this work. The advantages/disadvantages of these models and the referring algorithms of training of each one are described. Microwave planar devices, as Frequency Selective Surfaces and microstrip antennas, are in evidence due the increasing necessities of filtering and separation of eletromagnetic waves and the miniaturization of RF devices. Therefore, it is of fundamental importance the study of the structural parameters of these devices in a fast and accurate way. The presented results, show to the capacities of the neural techniques for modeling both Frequency Selective Surfaces and antennas

Determination of copper in fish feed by graphite furnace atomic absorption spectrometry using slurry sampling

The present work develops and optimizes a method to determine copper in samples of feces and fish feed by graphite furnace atomic absorption spectrometry (GFAAS) through the direct introduction of slurries of the samples into the spectrometer's graphite tube coated internally with metallic rhodium and tungsten carbide that acts as chemical modifiers. The limits of detection (LOD) and quantification (LOQ) calculated for 20 readings of the blank of the standard slurries (0.50% m/v of feces or feed devoid of copper) were 0.24 and 0.79 μg L -1 for the standard feces slurries and 0.26 and 0.87 μg L -1 for the standard feed slurries. The proposed method was applied in studies of absorption of copper in different fish feeds and their results proved compatible with that obtained from samples mineralized by acid digestion using microwave oven. © Springer Science+Business Media, LLC 2008.

Contribución al desarrollo de técnicas CAD para el diseño de antenas impresas y dispositivos pasivos de microondas basadas en el método de elementos finitos

El objetivo principal de esta tesis es el desarrollo de herramientas numéricas basadas en técnicas de onda completa para el diseño asistido por ordenador (Computer-Aided Design,‘CAD’) de dispositivos de microondas. En este contexto, se desarrolla una herramienta numérica basada en el método de los elementos finitos para el diseño y análisis de antenas impresas mediante algoritmos de optimización. Esta técnica consiste en dividir el análisis de una antena en dos partes. Una parte de análisis 3D que se realiza sólo una vez en cada punto de frecuencia de la banda de funcionamiento donde se sustituye una superficie que contiene la metalización del parche por puertas artificiales. En una segunda parte se inserta entre las puertas artificiales en la estructura 3D la superficie soportando una metalización y se procede un análisis 2D para caracterizar el comportamiento de la antena. La técnica propuesta en esta tesis se puede implementar en un algoritmo de optimización para definir el perfil de la antena que permite conseguir los objetivos del diseño. Se valida experimentalmente dicha técnica empleándola en el diseño de antenas impresas de banda ancha para diferentes aplicaciones mediante la optimización del perfil de los parches. También, se desarrolla en esta tesis un procedimiento basado en el método de descomposición de dominio y el método de los elementos finitos para el diseño de dispositivos pasivos de microonda. Se utiliza este procedimiento en particular para el diseño y sintonía de filtros de microondas. En la primera etapa de su aplicación se divide la estructura que se quiere analizar en subdominios aplicando el método de descomposición de dominio, este proceso permite analizar cada segmento por separado utilizando el método de análisis adecuado dado que suele haber subdominios que se pueden analizar mediante métodos analíticos por lo que el tiempo de análisis es más reducido. Se utilizan métodos numéricos para analizar los subdominios que no se pueden analizar mediante métodos analíticos. En esta tesis, se utiliza el método de los elementos finitos para llevar a cabo el análisis. Además de la descomposición de dominio, se aplica un proceso de barrido en frecuencia para reducir los tiempos del análisis. Como método de orden reducido se utiliza la técnica de bases reducidas. Se ha utilizado este procedimiento para diseñar y sintonizar varios ejemplos de filtros con el fin de comprobar la validez de dicho procedimiento. Los resultados obtenidos demuestran la utilidad de este procedimiento y confirman su rigurosidad, precisión y eficiencia en el diseño de filtros de microondas. ABSTRACT The main objective of this thesis is the development of numerical tools based on full-wave techniques for computer-aided design ‘CAD’ of microwave devices. In this context, a numerical technique based on the finite element method ‘FEM’ for the design and analysis of printed antennas using optimization algorithms has been developed. The proposed technique consists in dividing the analysis of the antenna in two stages. In the first stage, the regions of the antenna which do not need to be modified during the CAD process are initially characterized only once from their corresponding matrix transfer function (Generalized Admittance matrix, ‘GAM’). The regions which will be modified are defined as artificial ports, precisely the regions which will contain the conducting surfaces of the printed antenna. In a second stage, the contour shape of the conducting surfaces of the printed antenna is iteratively modified in order to achieve a desired electromagnetic performance of the antenna. In this way, a new GAM of the radiating device which takes into account each printed antenna shape is computed after each iteration. The proposed technique can be implemented with a genetic algorithm to achieve the design objectives. This technique is validated experimentally and applied to the design of wideband printed antennas for different applications by optimizing the shape of the radiating device. In addition, a procedure based on the domain decomposition method and the finite element method has been developed for the design of microwave passive devices. In particular, this procedure can be applied to the design and tune of microwave filters. In the first stage of its implementation, the structure to be analyzed is divided into subdomains using the domain decomposition method; this process allows each subdomains can be analyzed separately using suitable analysis method, since there is usually subdomains that can be analyzed by analytical methods so that the time of analysis is reduced. For analyzing the subdomains that cannot be analyzed by analytical methods, we use the numerical methods. In this thesis, the FEM is used to carry out the analysis. Furthermore the decomposition of the domain, a frequency sweep process is applied to reduce analysis times. The reduced order model as the reduced basis technique is used in this procedure. This procedure is applied to the design and tune of several examples of microwave filters in order to check its validity. The obtained results allow concluding the usefulness of this procedure and confirming their thoroughness, accuracy and efficiency for the design of microwave filters.