The measurement of actual acidity in acid sulfate soils and the determination of sulfidic acidity in suspension after peroxide oxidation

Improvements to the routine methods for the determination of actual acidity in suspension for acid sulfate soils (ASS) are introduced. The titratable sulfidic acidity (TSA) results using an improved peroxide-based method were compared with the theoretical acidity predicted by the chromium reducible sulfur method for 9 acid sulfate soils. The regression between these 2 measures of sulfidic acidity was highly significant, the slope of the regression line not significantly different from unity (P = 0.05) and the intercept not significantly different from zero. This contrasts with results of other workers using earlier peroxide oxidation methods, where TSA substantially underestimated the theoretical acidity predicted by reduced inorganic sulfur analysis. Comparison was made between the 2 principal measurements from the improved peroxide method (TSA and S-POS), with S-POS converted to theoretical sulfidic acidity to allow comparison. The relationship between these 2 measurements was highly significant. The effects of titration in suspension, as well as raising titration end points to pH 6.5, were investigated, principally with respect to the titratable actual acidity (TAA) result. TAA results obtained by KCl extraction were compared with those obtained using BaCl2, MgCl2, and water extraction. TAA in 1 M KCl suspensions titrated to pH 6.5 agreed well with titratable actual acidity measured using the 25-h extraction approach of the Lin et al. (2000a) BaCl2 method. Both BaCl2 and KCl solutions were ineffective at fully recovering acidity from synthetic jarosite without repeated extraction and titration. The application of correction factors for the estimation of total actual acidity in ASS is not supported by the results of this investigation. Acid sulfate soils that contain substantial quantities of jarosite or other acid-producing but relatively insoluble sulfate minerals continue to prove problematic to chemically analyse; however, an approach for estimating this component is discussed.

Sulfate Mineral Paragenesis in Pennsylvanian Rocks and The Occurrence of Slavikite in Nebraska

The acid weathering of pyrite-bearing Pennsylvanian clastic sedimentary rocks in southeastern Nebraska locally produces the secondary sulfate minerals alunogen, copiapite, epsomite, felsobanyaite/basaluminite, gypsum, halotrichite, jarosite, rozenite, and slavikite. Of these mineral occurrences, four are first-time discoveries in the state or the surrounding region. Slavikite (NaMg2Fe5 (S04)7 (OH) 6• 33H20), which has been reported only once before in North America and from a handful of sites in Europe and South America, was found in abundance at an outcrop at Brownville, NE. The pH values in 1:1 solutions of deionized water of the studied minerals, excluding epsomite, range from 1.94 to 4.82. Therefore, segregations of secondary minerals in themselves are significant microenvironmental reservoirs of acid that can be mobilized during precipitation events. Because of its role in liberating and concentrating ions such as Al3+, Fe2+, Fe3+, Mg3+, and SO42-, acid rock weathering should be considered in local to regional assessments of surface-water and groundwater chemistry. Observations also suggest that rock weathering by the growth of sulfate salts is a potential factor in local hillslope development, one that has not previously been considered in the study area.

(Table 1) Sulfur contents and isotope composition in rocks and minerals from DSDP/ODP Hole 504B

DSDP Hole 504B is the only hole in oceanic crust to penetrate through the volcanic section and into hydrothermally altered sheeted dikes. We have carried out petrologic and sulfur isotopic analyses of sulfide and sulfate minerals and whole rocks from the core in order to place constraints on the geochemistry of sulfur during hydrothermal alteration of ocean crust. The nearly 600 m-thick pillow section has lost sulfur to seawater and has net d34S = -1.8 per mil due to degassing of SO2 during crystallization and subsequent low temperature interaction with seawater. Hydrothermally altered rocks in the 200 m-thick transition zone are enriched in S and 34S (4300 ppm and +3.0 +/-1.2 per mil, respectively), whereas the more than 500 m of sheeted dikes contain 720 ppm S with d34S = +0.6 +/-1.4 per mil. These data are consistent with the presence of predominantly basaltic sulfur in hydrothermal fluids deep in the crust: following precipitation of anhydrite during seawater recharge, small amounts of seawater sulfate were reduced at temperatures >250°C through conversion of igneous pyrrhotite to secondary pyrite and minor oxidation of ferrous iron in the crust. The S- and 34S-enrichments of the transition zone are the results of seawater sulfate reduction and sulfide deposition during subsurface mixing between upwelling hot (up to 350°C) hydrothermal fluids and seawater. Seawater sulfate was probably reduced through oxidation of ferrous iron in hydrothermal fluids and in the transition zone rocks. Alteration of the upper crust resulted in loss of basaltic sulfur to seawater, fixation of minor seawater sulfur in the crust and redistribution of magmatic sulfur within the crust. This caused net increases in sulfur content and d34S of the upper 1.8 km of the oceanic crust.

Sulfur speciation and stable isotope trends of water-soluble sulfates in mine tailings profiles

Sulfur speciation and the sources of water-soluble sulfate in three oxidizing sulfidic mine tailings impoundments were investigated by selective dissolution and stable isotopes. The studied tailings impoundments-Piuquenes, Cauquenes, and Salvador No. 1-formed from the exploitation of the Rio Blanco/La Andina, El Teniente, and El Salvador Chilean porphyry copper deposits, which are located in Alpine, Mediterranean, and hyperarid climates, respectively. The water-soluble sulfate may originate from dissolution of primary ore sulfates (e.g., gypsum, anhydrite, jarosite) or from oxidation of sulfide minerals exposed to aerobic conditions during mining activity. With increasing aridity and decreasing pyrite content of the tailings, the sulfur speciation in the unsaturated oxidation zones showed a trend from dominantly Fe(Ill) oxyhydroxide fixed sulfate (e.g., jarosite and schwertmannite) in Piuquenes toward increasing presence of water-soluble sulfate at Cauquenes and Salvador No. 1. In the saturated primary zones, sulfate is predominantly present in water-soluble form (mainly as anhydrite and/or gypsum). In the unsaturated zone at Piuquenes and Cauquenes,the delta(34)S(S04) values ranged from +0.5 parts per thousand to +2.0 parts per thousand and from -0.4 parts per thousand to +1.4 parts per thousand Vienna Canyon Diablo Troilite (V-CDT), respectively, indicating a major sulfate source from pyrite oxidation (delta(34)S(pyrite) -1.1 parts per thousand and -0.9 parts per thousand). In the saturated zone at Piuquenes and Cauquenes, the values ranged from -0.8%. to +0.3 parts per thousand and from +2.2 parts per thousand to +3.9 parts per thousand, respectively. At Cauquenes the 34 S enrichment in the saturated zone toward depth indicates the increasing contribution of isotopically heavy dissolved sulfate from primary anhydrite (similar to+10.9%o). At El Salvador No. 1, the delta(34)S(SO4) average value is -0.9 parts per thousand, suggesting dissolution of supergene sulfate minerals (jarosite, alunite, gypsum) with a delta(34)S similar to -0.7 parts per thousand as the most probable sulfate source. The gradual decrease Of delta(18)O(S04) values from the surface to the oxidation front in the tailings impoundments at Piuquenes (from -4.5 parts per thousand to -8.6 parts per thousand Vienna Standard Mean Ocean Water, V-SMOW) and at Cauquenes (from -1.3 parts per thousand to -3.5 parts per thousand) indicates the increasing importance of ferric iron as the main electron acceptor in the oxidation of pyrite. The different delta(18)O(SO4) values between the tailings impoundments studied here reflect the local climates.

Chemistry, isotope values (δD, δ18O, δ34S(SO4)) and temperatures of the water inflows in two Gotthard tunnels, Swiss Alps

Water inflows in the Gotthard Highway Tunnel and in the Gotthard Exploration Tunnel are meteoric waters infiltrating at different elevations, on both sides of an important orographic divide. Limited interaction of meteoric waters with gneissic rocks produces Ca-HCO3 and Na-Ca-HCO3 waters, whereas prolonged interaction of meteoric waters with the same rocks generates Na-HCO3 to Na-SO4 waters. Waters circulating in Triassic carbonate-evaporite rocks have a Ca-SO4 composition. Calcium-Na-SO4 waters are also present. They can be produced through interaction of either Na-HCO3 waters with anhydrite or Ca-SO4 waters with a local gneissic rock, as suggested by reaction path modeling. An analogous simulation indicates that Na-HCO3 waters are generated through interaction of Ca-HCO3 waters with a local gneissic rock. The two main SO4-sources present in the Alps are leaching of upper Triassic sulfate minerals and oxidative dissolution of sulfide minerals of crystalline rocks. Values of delta S-34(SO4) < <similar to>+ 9 parts per thousand, are due to oxidative dissolution of sulfide minerals, whereas delta S-34(SO4) > similar to+ 9 parts per thousand are controlled either by bacterial SO4 reduction or leaching of upper Triassic sulfate minerals. Most waters have temperatures similar to the expected values for a geothermal gradient of 22 degreesC/km and are close to thermal equilibrium with rocks. However relatively large, descending flows of cold waters and ascending flows of warm waters are present in both tunnels and determine substantial cooling and heating, respectively, of the interacting rocks. The most import upflow zone of warm, Na-rich waters is below Guspisbach, in the Gotthard Highway Tunnel, at 6.2-9.0 km from the southern portal. These warm waters have equilibrium temperatures of 65-75 degreesC and therefore constitute an important low-enthalpy geothermal resource. (C) 2001 Elsevier Science Ltd. All rights reserved.

Evaluation of Microcracking and Chemical Deterioration in Concrete Pavements, October 31, 1995

The major objective of this research project was to investigate the chemistry and morphology of portland cement concrete pavements in Iowa. The integrity of the various pavements was evaluated qualitatively, based on the presence or absence of microcracks, the presence or absence of sulfate minerals, and the presence or absence of alkali-silica gel(s). Major equipment delays and subsequent equipment replacements resulted in significant delays over the course of this research project. However, all these details were resolved and the equipment is currently in place and fully operational. The equipment that was purchased for this project included: (I) a LECO VP 50, 12-inch diameter, variable speed grinder/polisher: (2) a Hitachi S-2460N variable pressure scanning electron microscope; and (3) a OXFORD Instruments Link ISIS microanalysis system with a GEM (high-purity germanium) X-ray detector. This study has indicated that many of the concrete pavements contained evidence of multiple deterioration mechanisms: and hence, the identification of a single reason for the distress that was observed in any given pavement typically had to be based on opinion rather than empirical evidence.

Evaluation of Microcracking and Chemical Deterioration in Concrete Pavements Final Report, October 31, 1995

The major objective of this research project was to investigate the chemistry and morphology of portland cement concrete pavements in Iowa. The integrity of the various pavements was evaluated qualitatively, based on the presence or absence of microcracks, the presence or absence of sulfate minerals, and the presence or absence of alkali-silica gel(s). Major equipment delays and subsequent equipment replacements resulted in significant delays over the course of this research project. However, all these details were resolved and the equipment is currently in place and fully operational. The equipment that was purchased for this project included: ( I ) a LECO VP 50, 12-inch diameter, variable speed grinder/polisher: (2) a Hitachi S-2460N variable pressure scanning electron microscope; and (3) a OXFORD Instruments Link ISIS microanalysis system with a GEM (high-purity germanium) X-ray detector. This study has indicated that many of the concrete pavements contained evidence of multiple deterioration mechanisms: and hence, the identification of a single reason for the distress that was observed in any given pavement typically had to be based on opinion rather than empirical evidence.

Evaluation of Microcracking and Chemical Deterioration in Concrete Pavements: Phase II, HR-358, Progress Report, 1995

The major objective of this research project is to investigate the chemistry and morphology of Portland cement concrete pavements in Iowa. The integrity of the various pavements is being ascertained based on the presence or absence of microcracks, the presence or absence of sulfate minerals, and the presence or absence of alkali-silica gel(s). Work is also being done on quantifying the air content of the concrete using image analysis techniques since this often appears to be directly related to the sulfate minerals that are commonly observed in the pavement cores.

Thermal degradation of both latex and latex cast films forming membranes: combined TG/FTIR investigation

Latex collected from natural rubber trees forming membranes can be used as biomaterials in several fields being the temperature a key parameter. Thermogravimetry (TG) coupled to Fourier transform infrared spectroscopy (FTIR) is a useful technique to investigate the thermal degradation of both latex and cast films (membranes), wich were obtained from Hevea brasiliensis (RRIM 600 clone) and used without stabilization. The membranes were prepared by casting the latex onto a glass substrate at 65 degrees C for 6 h. The thermal degradation was followed by FTIR spectra acquisition along the process, allowing the identification of the gaseous components evolved upon the thermal treatment. According to TG measurements, the main processes of thermal degradation of the latex and membranes occur at three temperature intervals for both.

Characterization of diagenetic fluids at ODP Site 103-639

Site 639, drilled during Leg 103 of the Ocean Drilling Program, penetrated an Upper Jurassic to Lower Cretaceous carbonate platform on a tilted fault block along the Galicia margin off the northwest Iberian Peninsula. The carbonate platform is composed primarily of a sequence of dolomite overlying limestone. Samples were analyzed for mineral chemistry, stable isotope geochemistry, fluid inclusion microthermometry, and volatile contents and by dolomite pyrolysis mass spectrometry for trace sulfate minerals. The dolomite recovered from the Galicia margin at Site 639 formed during shallow burial from sulfate-bearing, hypersaline brines at slightly elevated temperatures. The light oxygen isotopic signatures of the dolomite are interpreted as the result of the evaporative loop and slightly elevated temperatures during dolomite formation or from reequilibration at higher temperatures during deeper burial. The hypersalinity is interpreted to be associated with a nearby, shallow restricted basin that formed during rifting of the Iberian margin from Newfoundland. The dolomitization of the platform is therefore a by-product of the rifting.

Chert petrology and geochemistry at DSDP Leg 62 Holes

Sixty-five chert, porcellanite, and siliceous-chalk samples from Deep Sea Drilling Project Leg 62 were analyzed by petrography, scanning electron microscopy, analysis by energy-dispersive X-rays, X-ray diffraction, X-ray spectroscopy, and semiquantitative emission spectroscopy. Siliceous rocks occur mainly in chalks, but also in pelagic clay and marlstone at Site 464. Overall, chert probably constitutes less than 5% of the sections and occurs in deposits of Eocene to Barremian ages at sub-bottom depths of 10 to 820 meters. Chert nodules and beds are commonly rimmed by quartz porcellanite; opal-CT-rich rocks are minor in Leg 62 sediments 65 to 108 m.y. old and at sub-bottom depths of 65 to 520 meters. Chert ranges from white to black, shades of gray and brown being most common; yellow-brown and red-brown jaspers occur at Site 464. Seventy-eight percent of the studied cherts contain easily recognizable burrow structures. The youngest chert at Site 463 is a quartz cast of a burrow. Burrow silica maturation is always one step ahead of host-rock silicification. Burrows are commonly loci for initial silicification of the host carbonate. Silicification takes place by volume-f or-volume replacement of carbonate sediment, and more-clay-rich sediment at Site 464. Nannofossils are commonly pseudomorphically replaced by quartz near the edges of chert beds and nodules. Other microfossils, mostly radiolarians and foraminifers, whether in chalk or chert, can be either filled with or replaced by calcite, opal-CT, and (or) quartz. Chemical micro-environments ultimately control the removal, transport, and precipitation of calcite and silica. Two cherts from Site 465 contain sulfate minerals replaced by quartz. Site 465 was never subaerially exposed after sedimentation began, and the formation of the sulfate minerals and their subsequent replacement probably occurred in the marine environment. Several other cherts with odd textures are described in this paper, including (1) a chert breccia cemented by colloform opal-CT and chalcedony, (2) a transition zone between white porcellanite containing opal-CT and quartz and a burrowed brown chert, consisting of radial aggregates of opal-CT with hollow centers, and (3) a chert that consists of silica-replaced calcite pseudospherules interspersed with streaks and circular masses of dense quartz. X-ray-diffraction analyses show that when data from all sites are considered there are poorly defined trends indicating that older cherts have better quartz crystallinity than younger ones, and that opal-CT crystallite size increases and opal-CT cf-spacings decrease with depth of occurrence in the sections. In a general way, depth of burial and the presence of calcite promote the ordering in the opal-CT crystal structure which allows its eventual conversion to quartz. Opal-CT in porcellanites converts to quartz after reaching a minimum d-spacing of 4.07 Å. Quartz/opal-CT ratios and quartz crystallinity vary randomly on a fine scale across four chert beds, but quartz crystallinity increases from the edge to the center of a fifth chert bed; this may indicate maturation of the silica. Twenty-four rocks were analyzed for their major- and minor-element compositions. Many elements in cherts are closely related to major mineral components. The carbonate component is distinguished by high values of CaO, MgO, Mn, Ba, Sr, and (for unknown reasons) Zr. Tuffaceous cherts have high values of K and Al, and commonly Zn, Mo, and Cr. Pure cherts are characterized by high SiO2 and B. High B may be a good indicator of formation of chert in an open marine environment, isolated from volcanic and terrigenous materials.