The DEAR-COTS hard real-time subsystem

In this report, the Hard Real-Time Subsystem of DEAR-COTS is described, and the services it must provide are identified. This report is an input of ISEP/IPP and FEUP for the specification of the DEAR-COTS architecture (deliverable to the FCT).

Updating of the hierarchical rock mass rating (HRMR) system and a new subsystem developed for weathered granite formations

The RMR system is still very much applied in rock mechanics engineering context. It is based on the evaluation of six weights to obtain a final rating. To obtain the final rating a considerable amount of information is needed concerning the rock mass which can be difficult to obtain in some projects or project stages at least with accuracy. In 2007 an alternative classification scheme based on the RMR, the Hierarchical Rock Mass Rating (HRMR) was presented. The main feature of this system was the adaptation to the level of knowledge existent about the rock mass to obtain the classification of the rock mass since it followed a decision tree approach. However, the HRMR was only valid for hard rock granites with low fracturing degrees. In this work, the database was enlarged with approximately 40% more cases considering other types of granite rock masses including weathered granites and based on this increased database the system was updated. Granite formations existent in the north of Portugal including Porto city are predominantly granites. Some years ago a light rail infrastructure was built in the city of Porto and surrounding municipalities whi h involved considerable challenges due to the high heterogeneity levels of the granite formations and the difficulties involved in their geomechanical characterization. In this work it is intended to provide also a contribution to improve the characterization of these formations with special emphasis to the weathered horizons. A specific subsystem applicable to the weathered formations was developed. The results of the validation of these systems are presented and show acceptable performances in identifying the correct class using less information than with the RMR system.

Transport Resource Management within UMTS Radio Network Subsystem

Tällä hetkellä haastavin telekommunikaatioteollisuuden tutkimus – ja kehitystoiminta on keskittynyt kolmannen sukupolven matkapuhelinjärjestelmien ympärille. Järjestelmien standardointityössä on saatu aikaiseksi ensimmäiset vakaat spesifikaatioversiot ja kaupallista toimintaa ollaan parhaillaan aloittelemassa Japanissa ja Euroopassa. Eräs kolmannen sukupolven järjestelmistä on UMTS (Universal Mobile Telecommunications System). Tämä diplomityö antaa yleiskuvan UMTS järjestelmästä ja sen eri verkkoelementtien toiminnallisuuksista. Päähuomio on kiinnitetty radioverkkojärjestelmään (UMTS Terrestrial Radio Access Network) ja erityisesti sen radioaliverkkojärjestelmään (Radio Network Subsystem), joka koostuu radioverkonohjaimesta (Radio Network Controller) ja joukosta siihen kuuluvia tukiasemia (Node B). Radioverkonohjain ja tukiasemat on yhdistetty avoimen rajapinnan kautta jota kutsutaan Iub -rajapinnaksi. Rajapinta tarjoaa radioverkonohjaimelle mahdollisuuden kontrolloida tukiasemia signalointiviestien avulla ja mahdollistaa tehokkaan ja luotettavan käyttäjätiedon siirron radioaliverkkojärjestelmän sisällä. Tämän diplomityön pääasiallinen sisältö on siirtoresurssien hallinta Iub -rajapinnan ylitse. Työssä esitellään ja selitetään siirtoverkon arkkitehtuuri. Myös kaikki Iub:ssä sijaitsevat protokollat ja toiminnalliset yksiköt jotka vaikuttavat siirtoresurssien hallintaan esitellään ja kuvataan yksityiskohtaisesti. Päähuomio on kiinnitetty sovellusprotokolliin sekä rajapinnan siirtoverkko- että radioverkkokerroksella sekä näiden protokollien väliseen vuorovaikutukseen. Kyseiset protokollat ovat Node B Application Part (NBAP) ja Access Link Control Application Part (ALCAP). Työn toteutusosassa käydään lävitse NBAP –protokollan prototyypin ja Node B Manager –toiminnallisen yksikön prototyypin implementaatio.

Subsystem Testing of Message Guided State Machines Using a Simulator Framework

Simulaattorit ovat yksinkertaistettuja malleja tietyistä järjestelmän osioista. Niitä käytetään mallintamaan testattavan osion ympärillä olevien muiden osioiden ulkoista toimintaa, jotta testattavalle osiolle saadaan oikeanlainen toimintaympäristö aikaiseksi. Tilakoneita käytetään mallintamaan ohjelmistojen tai niiden osien toimintaa. Sanomaohjatuissa tilakoneissa tilojen vaihdot perustuvat saapuviin sanomiin. Tässä työssä esitellään erään ohjelmiston alijärjestelmän testaamisessa käytettävä arkkitehtuuri, joka perustuu suurelta osin simulaattoreiden käyttöön muiden alijärjestelmien mallintamisessa. Testattava ohjelmisto koostuu enimmäkseen tilakoneista, jotka vaihtavat keskenään sanomia ja ohjaavat näin toistensa tilasiirtymiä. Työn testausympäristö on suunniteltu juuri tämänkaltaisen ohjelmiston testaamiseen. Työssä esiteltävää testausympäristöä myöskin käytettiin useamman kuukauden ajan ja se todettiin toimivaksi. Joitakin testausympäristön käyttöohjeita, käyttökokemuksia sekä siihen liittyviä parannusehdotuksia käydään läpi työn loppuosassa. Erityisesti havaittiin miten tärkeää on testata implementaatiota jo luokka tasolla ennen alijärjestelmä tason testaukseen siirtymistä sekä päädyttiin siihen, että suunnitteluvaiheen pitäisi olla lähemmin liitoksissa alijärjestelmätestaukseen.

A Sociological Study of the Political Subsystem in Yugoslavia

In this critical analysis of sociological studies of the political subsystem in Yugoslavia since the fall of communism Mr. Ilic examined the work of the majority of leading researchers of politics in the country between 1990 and 1996. Where the question of continuity was important, he also looked at previous research by the writers in question. His aim was to demonstrate the overall extent of existing research and at the same time to identify its limits and the social conditions which defined it. Particular areas examined included the problems of defining basic concepts and selecting the theoretically most relevant indicators; the sources of data including the types of authentic materials exploited; problems of research work (contacts, field control, etc.); problems of analysisl and finally the problems arising from different relations with the people who commission the research. In the first stage of the research, looking at methods of defining key terms, special attention was paid to the analysis of the most frequently used terms such as democracy, totalitarianism, the political left and right, and populism. Numerous weaknesses were noted in the analytic application of these terms. In studies of the possibilities of creating a democratic political system in Serbia and its possible forms (democracy of the majority or consensual democracy), the profound social division of Serbian society was neglected. The left-right distinction tends to be identified with the government-opposition relation, in the way of practical politics. The idea of populism was used to pass responsibility for the policy of war from the manipulator to the manipulated, while the concept of totalitarianism is used in a rather old-fashioned way, with echoes of the cold war. In general, the terminology used in the majority of recent research on the political subsystem in Yugoslavia is characterised by a special ideological style and by practical political material, rather than by developed theoretical effort. The second section of analysis considered the wider theoretical background of the research and focused on studies of the processes of transformation and transition in Yugoslav society, particularly the work of Mladen Lazic and Silvano Bolcic, who he sees as representing the most important and influential contemporary Yugoslav sociologists. Here Mr. Ilic showed that the meaning of empirical data is closely connected with the stratification schemes towards which they are oriented, so that the same data can have different meanings in shown through different schemes. He went on to show the observed theoretical frames in the context of wider ideological understanding of the authors' ideas and research. Here the emphasis was on the formalistic character of such notions as command economy and command work which were used in analysing the functioning and the collapse of communist society, although Mr. Ilic passed favourable judgement on the Lazic's critique of political over-determination in its various attempts to explain the disintegration of the communist political (sub)system. The next stage of the analysis was devoted to the problem of empirical identification of the observed phenomena. Here again the notions of the political left and right were of key importance. He sees two specific problems in using these notion in talking about Yugoslavia, the first being that the process of transition in the FR Yugoslavia has hardly begun. The communist government has in effect remained in power continuously since 1945, despite the introduction of a multi-party system in 1990. The process of privatisation of public property was interrupted at a very early stage and the results of this are evident on the structural level in the continuous weakening of the social status of the middle class and on the political level because the social structure and dominant form of property direct the majority of votes towards to communists in power. This has been combined with strong chauvinist confusion associated with the wars in Croatia and Bosnia, and these ideas were incorporated by all the relevant Yugoslav political parties, making it more difficult to differentiate between them empirically. In this context he quotes the situation of the stream of political scientists who emerged in the Faculty of Political Science in Belgrade. During the time of the one-party regime, this faculty functioned as ideological support for official communist policy and its teachers were unable to develop views which differed from the official line, but rather treated all contrasting ideas in the same way, neglecting their differences. Following the introduction of a multi-party system, these authors changed their idea of a public enemy, but still retained an undifferentiated and theoretically undeveloped approach to the issue of the identification of political ideas. The fourth section of the work looked at problems of explanation in studying the political subsystem and the attempts at an adequate causal explanation of the triumph of Slobodan Milosevic's communists at four subsequent elections was identified as the key methodological problem. The main problem Mr. Ilic isolated here was the neglect of structural factors in explaining the voters' choice. He then went on to look at the way empirical evidence is collected and studied, pointing out many mistakes in planning and determining the samples used in surveys as well as in the scientifically incorrect use of results. He found these weaknesses particularly noticeable in the works of representatives of the so-called nationalistic orientation in Yugoslav sociology of politics, and he pointed out the practical political abuses which these methodological weaknesses made possible. He also identified similar types of mistakes in research by Serbian political parties made on the basis of party documentation and using methods of content analysis. He found various none-sided applications of survey data and looked at attempts to apply other sources of data (statistics, official party documents, various research results). Mr. Ilic concluded that there are two main sets of characteristics in modern Yugoslav sociological studies of political subsystems. There are a considerable number of surveys with ambitious aspirations to explain political phenomena, but at the same time there is a clear lack of a developed sociological theory of political (sub)systems. He feels that, in the absence of such theory, most researcher are over-ready to accept the theoretical solutions found for interpretation of political phenomena in other countries. He sees a need for a stronger methodological bases for future research, either 1) in complementary usage of different sources and ways of collecting data, or 2) in including more of a historical dimension in different attempts to explain the political subsystem in Yugoslavia.

Integration of room temperature single electron transistor with CMOS subsystem

The single electron transistor (SET) is a charge-based device that may complement the dominant metal-oxide-semiconductor field effect transistor (MOSFET) technology. As the cost of scaling MOSFET to smaller dimensions are rising and the the basic functionality of MOSFET is encountering numerous challenges at dimensions smaller than 10nm, the SET has shown the potential to become the next generation device which operates based on the tunneling of electrons. Since the electron transfer mechanism of a SET device is based on the non-dissipative electron tunneling effect, the power consumption of a SET device is extremely low, estimated to be on the order of 10^-18J. The objectives of this research are to demonstrate technologies that would enable the mass produce of SET devices that are operational at room temperature and to integrate these devices on top of an active complementary-MOSFET (CMOS) substrate. To achieve these goals, two fabrication techniques are considered in this work. The Focus Ion Beam (FIB) technique is used to fabricate the islands and the tunnel junctions of the SET device. A Ultra-Violet (UV) light based Nano-Imprint Lithography (NIL) call Step-and-Flash- Imprint Lithography (SFIL) is used to fabricate the interconnections of the SET devices. Combining these two techniques, a full array of SET devices are fabricated on a planar substrate. Test and characterization of the SET devices has shown consistent Coulomb blockade effect, an important single electron characteristic. To realize a room temperature operational SET device that function as a logic device to work along CMOS, it is important to know the device behavior at different temperatures. Based on the theory developed for a single island SET device, a thermal analysis is carried out on the multi-island SET device and the observation of changes in Coulomb blockade effect is presented. The results show that the multi-island SET device operation highly depends on temperature. The important parameters that determine the SET operation is the effective capacitance Ceff and tunneling resistance Rt . These two parameters lead to the tunneling rate of an electron in the SET device, Γ. To obtain an accurate model for SET operation, the effects of the deviation in dimensions, the trap states in the insulation, and the background charge effect have to be taken into consideration. The theoretical and experimental evidence for these non-ideal effects are presented in this work.

Rapid sizing tool for a low cost university microsatellite structure subsystem

In recent decays university class small satellites are creating many opportunities for space research and professional trainings while at the same time responding to constrained budgets. In this work the main focus is on developing a simple and rapid structural sizing tool considering the main objectives of a low cost university class microsatellite project. In satellite projects, structure subsystem is one of the influential subsystems as a driver of the cost and acceptance of the final design. At the first steps of such projects there is no confirmed data regarding the launch vehicle or even in some cases there is no data for the satellite payload. Due to these facts, developing simple sizing tools at conceptual design phase for obtaining an over view of the effect of different variables is useful before entering complex calculations in detailed design phases. In this study, after developing a simple analytical model of satellite structure subsystem, a design space is evaluated with practical boundaries considering mass and dimensions constraints of such projects. The results are useful to give initial insight to establish the system level structural sizing

Habilitadores para aplicación de teleconsulta sobre IP Multimedia Subsystem

En el presente trabajo se presenta el diseño e implementación de un conjunto de habilitadores o servicios genéricos para aplicaciones de teleconsulta sobre redes IMS. A partir de las funcionalidades identificadas en las aplicaciones de teleconsulta se han diseñado los habilitadores a desarrollar, que son los siguientes: una sala de espera virtual, una pizarra virtual y una multiconferencia multimedia. Estos servicios utilizan a su vez otros habilitadores genéricos referidos en el estado del arte de la arquitectura IMS. Tales servicios se han integrado en una arquitectura IMS para garantizar su funcionamiento. Para evaluar el funcionamiento de los habilitadores desarrollados se ha definido e implementado el caso de uso de una aplicación de teleconsulta avanzada.

A linear chained approach for service invocation in IP multimedia subsystem.

IP Multimedia Subsystem (IMS) is considered to provide multimedia services to users through an IP-based control plane. The current IMS service invocation mechanism, however, requires the Serving-Call Session Control Function (S-CSCF) invokes each Application Server (AS) sequentially to perform service subscription pro?le, which results in the heavy load of the S-CSCF and the long session set-up delay. To solve this issue, this paper proposes a linear chained service invocation mechanism to invoke each AS consecutively. By checking all the initial Filter Criteria (iFC) one-time and adding the addresses of all involved ASs to the ?Route? header, this new approach enables multiple services to be invoked as a linear chain during a session. We model the service invocation mechanisms through Jackson networks, which are validated through simulations. The analytic results verify that the linear chained service invocation mechanism can effectively reduce session set-up delay of the service layer and decrease the load level of the S-CSCF

Static analysis of WCET in a satellite software subsystem

This paper describes the authors? experience with static analysis of both WCET and stack usage of a satellite on-board software subsystem. The work is a continuation of a previous case study that used a dynamic WCET analysis tool on an earlier version of the same software system. In particular, the AbsInt aiT tool has been evaluated by analysing both C and Ada code generated by Simulink within the UPMSat-2 project. Some aspects of the aiT tool, specifically those dealing with SPARC register windows, are compared to another static analysis tool, Bound-T. The results of the analysis are discussed, and some conclusions on the use of static WCET analysis tools on the SPARC architecture are commented in the paper.