Substrate Preparation Behaviors for the Cultivation of the Symbiotic Fungus in Leaf-Cutting Ants of the Genus Atta (Hymenoptera: Formicidae)

Our findings revealed two distinct patterns of substrate preparation: the pattern of leaf-cutting ants foraging on dicotyledons is marked by highly fragmented substrate resulting in a more advanced initial decomposition. The pattern of leaf-cutting ants harvesting grasses is characterized by large pieces of substrate, resulting in little initial decomposition. Ants foraging on both types of plants are apparently intermediary between the two patterns, although more similar to the patterns of those foraging on dicotyledons. Also, the behavior of scraping the substrate was described for the first time, it is very important for the removal of the epicuticular wax layer of the leaves helping the growth of the symbiotic fungus.

Evolution of Substrate Preparation Behaviors for Cultivation of Symbiotic Fungus in Attine Ants (Hymenoptera: Formicidae)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Behavior of Atta sexdens rubropilosa (Hymenoptera: Formicidae) workers during the preparation of the leaf substrate for symbiont fungus culture

The behavioral repertory of Atta sexdens rubropilosa Forel (Hymenoptera: Formicidae) workers marked by size category was studied during the preparation of the leaf substrate in the laboratory. The workers were marked according to three physical castes, i.e., minima, generalist and forager. Seven types of behavioral acts were recorded for each caste, with the following frequencies: licking leaf fragments (64.6%), holding fragments on the surface of the fungus garden (16.4%), shredding the fragments (6.0%), chewing and crimping the edges of the fragments (9.0%), incorporating the fragments (2.7%), touching the surface of the fungus with their mandibles and other mouthparts after incorporation (0.3%), and depositing fecal fluid (0.1%). The minima workers were found to be more specialized in the activities related to the preparation of the leaf substrate, which represented 52% of the total number of tasks performed. The generalists performed 40.3% of these tasks, and the foragers 7.9%. Licking the substrate was the behavior most frequently recorded and performed for a longer period of time. In this way, the workers may feed and at the same time eliminate microorganisms that are harmful to the symbiont fungus. The smaller castes, minima and generalists, are those most responsible for the preparation of the leaf substrate and predominate within a colony. From a practical viewpoint, with the introduction of toxic bait containing insecticides, for example, these size categories will be those most intensely intoxicated, especially through the behavior of licking bait pellets. On the basis of the data obtained about these behaviors, we may raise the hypothesis that trophallaxis in not the major factor triggering contamination with an insecticide among the workers of a colony.

Atomic force microscopy of nucleoprotein complexes.

Recent data on the AFM studies of nucleoprotein complexes of different types are reviewed in this paper. The first section describes the progress in the sample preparation methods for AFM studies of nucleic acids and nucleoprotein complexes. The second part of this paper reviews AFM data on studies of complexes of DNA with regulatory proteins. These studies include two different types of DNA distortion induced by proteins binding: local bending of DNA at sites of protein binding and formation of large loops due to protein-protein interactions between molecules bound to distant sites along the DNA molecules (DNA looping). The prospects for use of AFM for physical mapping of genomes are discussed in this section as well. The third part of the paper reviews data on studies of complexes of DNA with non-sequence specific binding proteins. Special emphasis is given to studies of chromatin which have resulted in progress in the understanding of structure of native chromatin fiber. In this section, novel data on AFM studies of RecA-DNA filaments and complexes of dsRNA with the dsRNA-specific protein p25 are also presented. Discussion of the substrate preparation procedures in relation to the AFM studies of nucleoprotein complexes is given in the final section.

Evolução dos comportamentos de preparação do substrato para o cultivo do fungo simbionte e cuidados com a cria, rainha e alados em formigas da tribo Attini (Hymenoptera: Formicidae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comunidades de fungos em jardins de formigas cortadeiras com diferentes hábitos de forrageamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Synaptic connectivity in micropatterned networks of neuronal cells

The presented thesis describes the formation of functional neuronal networks on an underlying micropattern. Small circuits of interconnected neurons defined by the geometry of the patterned substrate could be observed and were utilised as a model system of reduced complexity for the behaviour of neuronal network formation and activity. The first set of experiments was conducted to investigate aspects of the substrate preparation. Micropatterned substrates were created by microcontact printing of physiological proteins onto polystyrene culture dishes. The substrates displayed a high contrast between the repellant background and the cell attracting pattern, such that neurons seeded onto these surfaces aligned with the stamped structure. Both the patterning process and the cell culture were optimised, yielding highly compliant low-density networks of living neuronal cells. In the second step, cellular physiology of the cells grown on these substrates was investigated by patch-clamp measurements and compared to cells cultivated under control conditions. It could be shown that the growth on a patterned substrate did not result in an impairment of cellular integrity nor that it had an impact on synapse formation or synaptic efficacy. Due to the extremely low-density cell culture that was applied, cellular connectivity through chemical synapses could be observed at the single cell level. Having established that single cells were not negatively affected by the growth on patterned substrates, aspects of network formation were investigated. The formation of physical contact between two cells was analysed through microinjection studies and related to the rate at which functional synaptic contacts formed between two neighbouring cells. Surprisingly, the rate of synapse formation between physically contacting cells was shown to be unaltered in spite of the drastic reduction of potential interaction partners on the micropattern. Additional features of network formation were investigated and found consistent with results reported by other groups: A different rate of synapse formation by excitatory and inhibitory neurons could be reproduced as well as a different rate of frequency-dependent depression at excitatory and inhibitory synapses. Furthermore, regarding simple feedback loops, a significant enrichment of reciprocal connectivity between mixed pairs of excitatory and inhibitory neurons relative to uniform pairs could be demonstrated. This phenomenon has also been described by others in unpatterned cultures [Muller, 1997] and may therefore be a feature underlying neuronal network formation in general. Based on these findings, it can be assumed that inherent features of neuronal behaviour and cellular recognition mechanisms were found in the cultured networks and appear to be undisturbed by patterned growth. At the same time, it was possible to reduce the complexity of the forming networks dramatically in a cell culture on a patterned surface. Thus, features of network architecture and synaptic connectivity could be investigated on the single cell level under highly defined conditions.

Tailoring molecule nanostructures on insulating surfaces investigated by non-contact atomic force microscopy

Self-assembled molecular structures were investigated on insulating substrate surfaces using non-contact atomic force microscopy. Both, substrate preparation and molecule deposition, took place under ultra-high vacuum conditions. First, C60 molecules were investigated on the TiO2 (110) surface. This surface exhibits parallel running troughs at the nanometer scale, which strongly steer the assembly of the molecules. This is in contrast to the second investigated surface. The CaF2 (111) surface is atomically flat and the molecular assemblyrnwas observed to be far less affected by the surface. Basically different island structures were observed to what is typically know. Based on extensive experimental studies and theoretical considerations, a comprehensive picture of the processes responsible for the island formation of C60 molecules on this insulating surfaces was developed. The key process for the emergence of the observed novel island structures was made out to be the dewetting of molecules from the substrate. This new knowledge allows to further understand andrnexploit self-assembly techniques in structure fabrication on insulating substrate surfaces. To alter island formation and island structure, C60 molecules were codeposited with second molecule species (PTCDI and SubPc) on the CaF2 (111) surface. Depending on the order of deposition, quiet different structures were observed to arise. Thus, these are the first steps towards more complex functional arrangements consisting of two molecule species on insulating surfaces.

General Protocol for the Culture of Cells on Plasma-Coated Electrospun Scaffolds

As opposed to culture on standard tissue-treated plastic, cell culture on three-dimensional scaffolds impedes additional challenges with respect to substrate preparation, cell seeding, culture maintenance, and analysis. We herewith present a general route for the culture of primary cells, differentiated cells, or stem cells on plasma-coated, electrospun scaffolds. We describe a method to prepare and fix the scaffolds in culture wells and discuss a convenient method for cell seeding and subsequent analysis by scanning electron microscopy or immunohistology.

Tuning the functional properties of Silicon Carbide Thin Film and Nanowires

The present thesis has been devoted to the synthesis and investigation of functional properties of silicon carbide thin films and nanowires. The work took profit from the experience of the research group in the synthesis of 3C-SiC from vapour phase. 3C-SiC thin films Thin films heteroepitaxy on silicon substrates was carried out in a vapour phase epitaxy reactor. The initial efforts were committed to the process development in order to enhance the crystal quality of the epi-layer. The carbonization process and a buffer layer procedure were optimized in order to obtain good quality monocrystalline 3C-SiC layers. The films characterization was used not only to improve the entire process, but also to assess the crystalline quality and to identify the defects. Methyltrichlorosilane (MTS) was introduced during the synthesis to increase the growth rate and enhance crystalline quality. The effect of synthesis parameters such as MTS flow and process temperature was studied in order to promote defect density reduction and the release of the strain due to lattice mismatch between 3C-SiC and silicon substrate. In-growth n-type doping was implemented using a nitrogen gas line and the effect of different synthesis parameters on doping level was studied. Raman measurements allowed a contactless characterization and evaluation of electrically active dopant. The effect of MTS on nitrogen incorporation was investigated and a promotion of dopant concentration together with a higher growth rate were demonstrated. This result allows to obtain higher doping concentrations without deteriorating crystal quality in 3C-SiC and, to the best of our knowledge, it has never been demonstrated before. 3C-SiC nanowires Core-shell SiC-SiO2 nanowires were synthesized using a chemical vapour deposition technique in an open tube configuration reactor on silicon substrates. Metal catalyst were used to promote a uniaxial growth and a dense bundle of nanowires 100 µm long and 60 nm thick was obtained. Substrate preparation was found to be fundamental in order to obtain a uniform nanowire density. Morphological characterization was carried out using scanning electron microscopy and the analysis of structural, compositional, optical properties is reported.

Development of surface flaw thresholds for pre-cured fiber reinforced polymer and groove size tolerance for near surface mounted fiber reinforced polymer retrofit systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. This study was conducted as part of the National Cooperative Highway Research Program (NCHRP) Project 10-59B to develop construction specifications and process control manual for repair and retrofit of concrete structures using bonded FRP systems. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The bond interface between FRP and concrete was modeled by a series of nonlinear springs. The model was validated against test data from the present study as well as those available from the literature. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of ±1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Development of Surface Flaw Thresholds for Pre-Cured Fiber Reinforced Polymer and Groove Size Tolerance for Near Surface Mounted Fiber Reinforced Polymer Retrofit Systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems, and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of +1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Interference of epicuticular wax from leaves of grasses in selection and preparation of substrate for cultivation of symbiont fungus by Atta capiguara (Hym. Formicidae)

The selection of plants is one of the stages of foraging behavior, executed by leaf-cutting ants for the cultivation of symbiont fungus. Anatomical, biochemical and physiological characteristics of vegetal species are some of the factors that influence selection of substrate; however, most studies described in the literature refer to leaf-cutting ants. Due to the scarcity of studies on the role of epicuticular waxes of grasses in relation to foraging behavior of monocotyledonous leaf-cutters, we completed three experiments with the ant species Atta capiguara in which we analyzed: the attractiveness or selectivity of leaves of Saccharum officinarum (sugarcane) and/or Hypharrenia rufa (capim jaraguá), with and without epicuticular wax in relation to the worker of this ant species, their processing and elimination in the form of pellets of epicuticular wax from the referred fragments removed by the workers for cultivation of symbiont fungus. We observed that vegetal fragments without wax were those most transported by workers to the inside of the nests; that they processed the fragments equally with as much as without wax, and eliminated, in the form of pellets, wax removed from the same into garbage chambers of the colonies, leading us to conclude that for monocotyledonous leaf-cutters, epicuticular wax from vegetal leaves has great importance in vegetal integrity by being used as substrate, representing a physical barrier to the growth of symbiont fungus.

Influence of cerium (IV) ions on the inorganic and organic phase for preparation of a siloxane-PMMA based film on tin plate substrate

Tinplate is one of the most widely used food canning materials, however, there are significant problems related to the use of tinplate cans, such as alterations in sensory features affecting food quality and corrosion phenomena of the canning material. To avoid corrosion problems different methods have been used for the passivation of tinplate such protective lacquers or different kinds of corrosion inhibitors (chromate and dichromate). However, chromates and dichromates are extremely harmful to the environment and can cause carcinogenic tumors to humans. An option, protective coatings obtained by the sol-gel process, act as a physical barrier, which isolates the surface of metal protecting from the corrosive agents. The aim of this work is to study the influence of addition of cerium (IV) ions in the inorganic and organic part of sol-gel processing in the formation of hybrid coatings based on siloxane-PMMA on tin plate. The coatings were obtained by dip-coating technique and evaluated by open circuit and impedance measurements, linear polarization and polarization curves obtained in 3.5% NaCl solution. The results have clearly shown the improvement on the protective properties of the Ce 4+ modified film when added into the organic phase, which can be due to the formation of a more uniform and densely reticulated siloxane-PMMA film. © 2009 by NACE International.

Copolymers obtained by the radiation-induced grafting of styrene onto poly(tetrafluoroethylene-co-perfluoropropylvinyl ether) substrates. 1. Preparation and structural investigation

A study has been made to investigate the radiation grafting of styrene onto poly(tetrafluoroethylene-co-perfluoropropylvinyl ether) (PFA) substrates, using the simultaneous irradiation method. Two PFA polymers of different comonomer perfluoropropyl vinyl ether (PPVE) content and degree of crystallinity were used. Effects of grafting conditions such as monomer concentrations, type of solvent, dose rate, and irradiation dose on the grafting yield were investigated. Of the six different solvents used, the most efficient in terms of increasing grafting yield were dichloromethane, benzene, and methanol. The degree of grafting increased with increasing radiation dose up to 500 kGy, stabilizing above this dose. However, the grafting yield decreased with an increase in the dose rate. The grafting of styrene onto the PFA substrates was confirmed by FTIR-ATR and micro-Raman spectroscopy, The increase in the overall grafting yield was accompanied by a proportional increase in the penetration depth of the grafts into the substrate.