A microstructure based model of the deformation mechanisms and flow stress during elevated temperature straining of a magnesium alloy

We show that the variation of flow stress with strain rate and grain size in a magnesium alloy deformed at a constant strain rate and 450 °C can be predicted by a crystal plasticity model that includes grain boundary sliding and diffusion. The model predicts the grain size dependence of the critical strain rate that will cause a transition in deformation mechanism from dislocation creep to grain boundary sliding, and yields estimates for grain boundary fluidity and diffusivity.

Anisotropy in plastic deformation of extruded magnesium alloy sheet during tensile straining at high temperature

Experimental measurements are used to characterize the anisotropy of flow stress in extruded magnesium alloy AZ31 sheet during uniaxial tension tests at temperatures between 350°C and 450°C, and strain rates ranging from 10-5 to 10-2 s-1. The sheet exhibits lower flow stress and higher tensile ductility when loaded with the tensile axis perpendicular to the extrusion direction compared to when it is loaded parallel to the extrusion direction. This anisotropy is found to be grain size, strain rate, and temperature dependent, but is only weakly dependent on texture. A microstructure based model (D. E. Cipoletti, A. F. Bower, P. E. Krajewski, Scr. Mater., 64 (2011) 931–934) is used to explain the origin of the anisotropic behavior. In contrast to room temperature behavior, where anisotropy is principally a consequence of the low resistance to slip on the basal slip system, elevated temperature anisotropy is found to be caused by the grain structure of extruded sheet. The grains are elongated parallel to the extrusion direction, leading to a lower effective grain size perpendicular to the extrusion direction. As a result, grain boundary sliding occurs more readily if the material is loaded perpendicular to the extrusion direction.

Study of activated sludge separation by dynamic straining /

Mode of access: Internet.

STRAINING ENGINEERING OF GRAPHENE AND GRAPHENE-BASED NANOSTRUCTURES

Graphene has emerged as an extraordinary material with its capability to accommodate an array of remarkable electronic, mechanical and chemical properties. Extra-large surface-to-volume ratio renders graphene a highly flexible morphology, giving rise to intriguing observations such as ripples, wrinkles and folds as well as the potential to transform into other novel carbon nanostructures. Ultra-thin, mechanically tough, electrically conductive graphene films promise to enable a wealth of possible applications ranging from hydrogen storage scaffolds, electronic transistors, to bottom-up material designs. Enthusiasm for graphene-based applications aside, there are still significant challenges to their realization, largely due to the difficulty of precisely controlling the graphene properties. Controlling the graphene morphology over large areas is crucial in enabling future graphene-based applications and material design. This dissertation aims to shed lights on potential mechanisms to actively manipulate the graphene morphology and properties and therefore enable the material design principle that delivers desirable mechanical and electronic functionalities of graphene and its derivatives.

On the mechanism of microbial cell disruption in high-pressure homogenisation

The tensions produced in the wall of a rigid, thin-walled, liquid-filled sphere as it moves with an axisymmetric straining flow are examined. This problem has not been previously addressed. A generalised correlation for the maximum wall tension, expressed in dimensionless form as a Weber number (We), is developed in terms of the acceleration number (Ac) and Reynolds number (Re) of the straining flow. At low Reynolds number We is dominated by viscous forces, while inertial forces due to internal pressure gradients caused by sphere acceleration dominate at higher Re. The generalised correlation has been used to examine the case of a typical yeast cell (a thin-walled, liquid-filled sphere) passing through a typical high-pressure homogeniser (a straining-flow device). At 56 MPa homogenising pressure, a 6 mu m yeast cell experiences tensions in the inertially dominated regime (Re = 100). The correlation gives We = 0.206, corresponding to a maximum wall tension of 8 Nm(-1). This is equivalent to an applied compressive force of 150 mu N and compares favourably with the force required to break yeast cells under compressive micromanipulation (40-90 mu N). Inertial forces may therefore be an important and previously unrecognised. mechanism of microbial cell disruption during high-pressure homogenisation. Further work is required to examine the likelihood of cell deformation in the high-strain-rate short-residence-time environment of the homogeniser, and the effect that such deformation may have on the contribution of inertial forces to disruption. (C) 1998 Published by Elsevier Science Ltd. All rights reserved.

Evolution of three-dimensional folds for a non-Newtonian plate in a viscous medium

We derive analytical solutions for the three-dimensional time-dependent buckling of a non-Newtonian viscous plate in a less viscous medium. For the plate we assume a power-law rheology. The principal, axes of the stretching D-ij in the homogeneously deformed ground state are parallel and orthogonal to the bounding surfaces of the plate in the flat state. In the model formulation the action of the less viscous medium is replaced by equivalent reaction forces. The reaction forces are assumed to be parallel to the normal vector of the deformed plate surfaces. As a consequence, the buckling process is driven by the differences between the in-plane stresses and out of plane stress, and not by the in-plane stresses alone as assumed in previous models. The governing differential equation is essentially an orthotropic plate equation for rate dependent material, under biaxial pre-stress, supported by a viscous medium. The differential problem is solved by means of Fourier transformation and largest growth coefficients and corresponding wavenumbers are evaluated. We discuss in detail fold evolutions for isotropic in-plane stretching (D-11 = D-22), uniaxial plane straining (D-22 = 0) and in-plane flattening (D-11 = -2D(22)). Three-dimensional plots illustrate the stages of fold evolution for random initial perturbations or initial embryonic folds with axes non-parallel to the maximum compression axis. For all situations, one dominant set of folds develops normal to D-11, although the dominant wavelength differs from the Biot dominant wavelength except when the plate has a purely Newtonian viscosity. However, in the direction parallel to D-22, there exist infinitely many modes in the vicinity of the dominant wavelength which grow only marginally slower than the one corresponding to the dominant wavelength. This means that, except for very special initial conditions, the appearance of a three-dimensional fold will always be governed by at least two wavelengths. The wavelength in the direction parallel to D-11 is the dominant wavelength, and the wavelength(s) in the direction parallel to D-22 is determined essentially by the statistics of the initial state. A comparable sensitivity to the initial geometry does not exist in the classic two-dimensional folding models. In conformity with tradition we have applied Kirchhoff's hypothesis to constrain the cross-sectional rotations of the plate. We investigate the validity of this hypothesis within the framework of Reissner's plate theory. We also include a discussion of the effects of adding elasticity into the constitutive relations and show that there exist critical ratios of the relaxation times of the plate and the embedding medium for which two dominant wavelengths develop, one at ca. 2.5 of the classical Biot dominant wavelength and the other at ca. 0.45 of this wavelength. We propose that herein lies the origin of parasitic folds well known in natural examples.

Optimization study of hybrid spot-welded/bonded single-lap joints

Joining of components with structural adhesives is currently one of the most widespread techniques for advanced structures (e.g., aerospace or aeronautical). Adhesive bonding does not involve drilling operations and it distributes the load over a larger area than mechanical joints. However, peak stresses tend to develop near the overlap edges because of differential straining of the adherends and load asymmetry. As a result, premature failures can be expected, especially for brittle adhesives. Moreover, bonded joints are very sensitive to the surface treatment of the material, service temperature, humidity and ageing. To surpass these limitations, the combination of adhesive bonding with spot-welding is a choice to be considered, adding a few advantages like superior static strength and stiffness, higher peeling and fatigue strength and easier fabrication, as fixtures during the adhesive curing are not needed. The experimental and numerical study presented here evaluates hybrid spot-welded/bonded single-lap joints in comparison with the purely spot-welded and bonded equivalents. A parametric study on the overlap length (LO) allowed achieving different strength advantages, up to 58% compared to spot-welded joints and 24% over bonded joints. The Finite Element Method (FEM) and Cohesive Zone Models (CZM) for damage growth were also tested in Abaqus® to evaluate this technique for strength prediction, showing accurate estimations for all kinds of joints.

Numerical and experimental study of tensile strength of single and double-strap repairs

Adhesive bonding as a joining or repair method has a wide application in many industries. Repairs with bonded patches are often carried out to re-establish the stiffness at critical regions or spots of corrosion and/or fatigue cracks. Single and double-strap repairs (SS and DS, respectively) are a viable option for repairing. For the SS repairs, a patch is adhesively-bonded on one of the structure faces. SS repairs are easy to execute, but the load eccentricity leads to peel peak stresses at the overlap edges. DS repairs involve the use of two patches, one on each face of the structure. These are more efficient than SS repairs, due to the doubling of the bonding area and suppression of the transverse deflection of the adherends. Shear stresses also become more uniform as a result of smaller differential straining. The experimental and Finite Element (FE) study presented here for strength prediction and design optimization of bonded repairs includes SS and DS solutions with different values of overlap length (LO). The examined values of LO include 10, 20 and 30 mm. The failure strengths of the SS and DS repairs were compared with FE results by using the Abaqus® FE software. A Cohesive Zone Model (CZM) with a triangular shape in pure tensile and shear modes, including the mixed-mode possibility for crack growth, was used to simulate fracture of the adhesive layer. A good agreement was found between the experiments and the FE simulations on the failure modes, elastic stiffness and strength of the repairs, showing the effectiveness and applicability of the proposed FE technique in predicting strength of bonded repairs. Furthermore, some optimization principles were proposed to repair structures with adhesively-bonded patches that will allow repair designers to effectively design bonded repairs.

Effect of hole drilling at the overlap on the strength of single-lap joints

Bonded unions are gaining importance in many fields of manufacturing owing to a significant number of advantages to the traditional fastening, riveting, bolting and welding techniques. Between the available bonding configurations, the single-lap joint is the most commonly used and studied by the scientific community due to its simplicity, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes in single-lap joints is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses at the damage initiation sites in structures or alterations of the failure mechanism emerging from local modifications. In this work, the effect of hole drilling at the overlap on the strength of single-lap joints was analyzed experimentally with two main purposes: (1) to check whether or not the anchorage effect of the adhesive within the holes is more preponderant than the stress concentrations near the holes, arising from the sharp edges, and modification of the joints straining behaviour (strength improvement or reduction, respectively) and (2) picturing a real scenario on which the components to be bonded are modified by some external factor (e.g. retrofitting of decaying/old-fashioned fastened unions). Tests were made with two adhesives (a brittle and a ductile one) varying the adherend thickness and the number, layout and diameter of the holes. Experimental testing showed that the joints strength never increases from the un-modified condition, showing a varying degree of weakening, depending on the selected adhesive and hole drilling configuration.

Desenvolvimento de sistema de apoio dinâmico da chapa no corte em guilhotina

Guilhotinas são máquinas robustas, de corte rectilíneo, normalmente associadas a equipamentos de baixo custo, devido à pequena quantidade de dispositivos tecnológicos incorporados. No entanto, esta situação pode ser alterada através da criatividade dos projetistas deste tipo de equipamento. Analisando algumas operações específicas, pode-se observar que algumas ferramentas, quando associadas ao equipamento, podem aumentar substancialmente a produtividade do processo de corte e a qualidade do produto final. Em relação ao processo de corte de chapas finas de metal, pode-se observar que na fase final de corte, o peso do material a cortar é suspenso por uma pequena porção de material que ainda não foi sujeita ao corte. Este facto leva a uma deformação plástica nesta última zona, causando problemas de qualidade no produto final, que não ficará completamente plano. Este trabalho foi desenvolvido em torno deste problema, estudando a melhor solução para desenvolver uma nova ferramenta, capaz de evitar a falta de nivelamento da placa, após corte. Um novo equipamento foi concebido, capaz de ser facilmente incorporado na guilhotina, permitindo o acompanhamento da inclinação da lâmina durante a operação de corte. O sistema é totalmente automatizado, sendo operado por uma única instrução de corte dada pelo operador da máquina. Este sistema permite à empresa fabricante aumentar o valor agregado de cada máquina, oferecendo aos clientes soluções avançadas, contribuindo desta forma para a sustentabilidade do negócio da empresa.

Unexpected Triggers for Pheochromocytoma-Induced Recurrent Heart Failure

Pheochromocytoma crisis typically presents as paroxysmal episodes of headache, tachycardia, diaphoresis or hypertension. We describe an uncommon case of recurrent non-hypertensive heart failure with systolic dysfunction in a young female due to pheochromocytoma compression. It presented as acute pulmonary oedema while straining during pregnancy and later on as cardiogenic shock after a recreational body massage. Such crisis occurring during pregnancy is rare. Moreover, of the few reported cases of pheochromocytoma-induced cardiogenic shock, recreational body massage has not yet been reported as a trigger for this condition.

Patient satisfaction after biofeedback for constipation and pelvic floor dyssynergia.

Patients referred for chronic constipation frequently report symptoms of straining, feeling of incomplete evacuation, or the need to facilitate defecation digitally (dyschezia). When such patients show manometric evidence of inappropriate contraction or failure to relax the pelvic floor muscles during attempts to defecate, they are diagnosed as having pelvic floor dyssynergia (Rome I). To evaluate long-term satisfaction of patients with pelvic floor dyssynergia after biofeedback. Forty-one consecutive patients referred for chronic constipation at an outpatient gastrointestinal unit and diagnosed as having pelvic floor dyssynergia who completed a full course of biofeedback. Data have been collected using a standardised questionnaire. A questionnaire survey of patients' satisfaction rate and requirement of aperients was undertaken. Mean age and symptom duration were respectively 41 and 20 years. Half of patients reported fewer than 3 bowel motions per week. Patients were treated with a mean of 5 biofeedback sessions. At the end of the therapy pelvic floor dyssynergia was alleviated in 85% of patients and 49% were able to stop all aperients. Satisfaction was maintained at follow-up telephone interviews undertaken after a mean period of 2 years, as biofeedback was helpful for 79% of patients and 47% still abstained from intake of aperients. Satisfaction after biofeedback is high for patients referred for chronic constipation and diagnosed with pelvic floor dyssynergia. Biofeedback improves symptoms related to dyschezia and reduces use of aperients.

Efectos de las aceleraciones positivas en el organismo

El artículo describe los efectos de las aceleraciones positivas (+Gz) sobre el organismohumano. Se consideran los factores determinantes de las aceleraciones: intensidad, velocidad de comienzo, dirección y duración. La fisiopatología describe los factores hidrostáticos,hemodinámicos y de regulación refleja del aparato cardiocirculatorio. La exposición a +Gz produce reacciones adaptativas fisiológicas. Cuando éstas se superan, aparecen patologías de tipocardiocirculatorio, respiratorio, músculoesquelético, nervioso, sensorial,... Se describen los diferentes procedimientos y equipos específicos que protegen al piloto de los efectos de +Gz. Éstos incluyen las maniobras de contracción muscular, los trajes anti-G, los equipos de respiración a presión positiva, así como el entrenamiento en centrífuga.

Moderata Fonte y María Zambrano: por cuenta propia

In this paper, Rosa Rius thinks about feminine identity and its history, based on the expressions of freedom of two authors living four centuries apart: the Venetian humanist Moderata Fonte (1555-1592) and the Malagan philosopher María Zambrano (1904-1991). The fact that these women¿s freedom is taken as one of their main identifying elements, and straining the historical action of this freedom, unforeseen by the establishment, does not at all imply that the undeniable discrimination inflicted upon women throughout centuries is forgotten or goes on without protest.